NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index
Stopping Devices and Processes
HP NonStop S-Series System Expansion and Reduction Guide—522465-009
D-7
Prepare and Stop an E4SA
This example screen shows all open associations of the TCP/IP $ZTC20 process to
other processes. For example, $ZTN20, the Telserv process, appears in boldface.
This example screen shows all open Telserv sessions that the TCP/IP $ZTC20 process
has:
-> LISTOPENS PROCESS $ZTC20
TCPIP Listopens PROCESS \TROLL.$ZTC20
Openers PPID BPID PLFN BLFN Protocol Lport
$ZTN20 2,301 8 0 TCP telnet
$ZPT20 0,325 4 0 TCP echo
$ZTN20 2,301 9 0 TCP telnet
$ZPT20 0,325 5 0 TCP finger
$ZPT20 0,325 6 0 TCP ftp
$ZTN20 2,301 7 0 TCP telnet
$ZTN20 2,301 3 0 TCP telnet
$ZPM20 2,302 3 0 UDP 111
$ZPM20 2,302 4 0 TCP 111
$ZBK20 1,41 3 0 TCP 795
$ZBK20 1,41 4 0 TCP 800
$ZTN20 2,301 10 0 TCP telnet
$ZTN20 2,301 4 0 TCP telnet
$ZNET 0,24 4 0 #ZSPI *
$ZTN20 2,301 5 0 TCP telnet
$ZTN20 2,301 6 0 TCP telnet
-> LISTOPENS PROCESS $ZTN20
TELSERV Listopens PROCESS \TROLL.$ZTN20
Window Openers PCPU PPIN PLFN BCPU BPIN BLFN Servic
#PTCZA3G \TROLL $Z02F 7 20 1 N/A N/A N/A TACL
#PTCZA3V \TROLL $Z078 3 23 1 N/A N/A N/A TACL
#PTCZA3Y \TROLL $Z09Q 6 27 1 N/A N/A N/A TACL
#PTCZA3U \TROLL $Z06R 2 45 1 N/A N/A N/A TACL
#PTCZA3R \TROLL $Z05F 7 25 1 N/A N/A N/A TACL
#PTCZA3S \TROLL $Z06D 0 83 1 N/A N/A N/A TACL
#PTCZA3Y \TROLL 6 40 2 N/A N/A N/A TACL
#PTCZA3W \TROLL $Z07F 4 26 1 N/A N/A N/A TACL
#PTCZA3Y \TROLL 6 40 3 N/A N/A N/A TACL
#ZSPI \TROLL $ZNET 0 24 6 N/A N/A N/A ZSPI