NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index
Safety and Compliance
HP NonStop S-Series System Expansion and Reduction Guide—522465-009
Statements-3
Regulatory Compliance Statements
Declares under our sole responsibility that the following product
Conforms to the following normative European and International Standards.
Following the provisions of the normative European Council Directives:
EMC Directive 89/336/EEC (including amendments)
Low Voltage Directive 73/23/EEC (amended by 93/68/EEC)
Supplementary Information:
Product conformance to cited product specifications is based on sample (type) testing, evaluation, or
assessment at Hewlett Packard’s compliance laboratories in Cupertino, California or at accredited laboratories
accepted by European Union Notified and Competent Bodies
.
DECLARATION OF CONFORMITY
Supplier Name: HP COMPUTER CORPORATION
Supplier Address: HP Computer Corporation,
NonStop Enterprise Division
10333 Vallco Parkway
Cupertino, CA 95014
USA
Represented in the EU By:
Hewlett Packard EMEA GmbH
P.O. Box 81 02 44
81902 Munich
Germany
Product Name:
NonStop S-series server
Regulatory Model
CPTOF-0301
Product Model No:
S88000, S86000, S76000, S7600, S74000, S7400, S78000, S7800
Product Safety: EN60950:2003 (IEC 60950-1 1st Edition)
Electromagnetic EN 55022:1998 Radiated and Conducted Emission
Compatibility: EN 61000-3-2:2000 Harmonic Current Emission
EN 61000-3-3 +A1:2001 Voltage Fluctuation and Flicker
EN 55024:1998 EMC Immunity
Safety: Protection Class I, Pollution Degree II
Emissions: EMC Class A
Year Assessed/First Production: 2004
Charles Denning
Manager, Hardware Product Assurance
NonStop Enterprise Division
Cupertino, California