NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index

Glossary
G-Series Common Glossary
Glossary-6
authentication attributes
authentication attributes. Security attributes of a process that do not change unless a
successful reauthentication occurs or the super ID changes them. For Open System
Services (OSS) processes, the authentication attributes include the login name, real
user ID, real group ID, authentication system (node name), and group list.
authorization attributes. Security attributes of a process that can change through use of
functions such as
setuid() (or of Guardian procedures such as
PROCESS_CREATE_) without reauthentication. For Open System Services (OSS)
processes, the authorization attributes include the effective user ID, saved-set user ID,
saved-set group ID, user audit flags, and effective user name.
authorization key. A password required for logging on to a modem. If you plan to allow
dial-outs to a service provider, you must specify the authorization key of the service
provider’s modem during configuration of the OSM or TSM Notification Director.
automated cartridge subsystem (ACS). A type of tape library. Also known as automated
cartridge system.
Automated Data Processing (ADP). The term used in the FIPS PUB 94 document to refer
to computerized data processing equipment that is installed inside a computer room.
automatic cartridge loader (ACL). A device that stores multiple cartridge tapes and loads
them automatically, one at a time, into a tape drive.
automatic configuration. The automatic assignment of magnetic disk attributes to an
internal disk drive when it is inserted into a slot. Also known as
plug and play.
averaging. A measurement method for determining the average value of alternating voltage
and current waveforms. The averaging method involves sampling a waveform and
averaging the samples over the period of one cycle.
AWAN. See asynchronous wide area network (AWAN) servers.
AXCEL. The command used to invoke the Accelerator on a TNS/R system.
back-end board (BEB). A circuit board that translates fiber-optic signals from a 3216
controller or 6760 ServerNet device adapter into small computer system interface
(SCSI) commands and information for a tape drive. The BEB is housed in a cage-like
sheet-metal enclosure and plugs into one of the 50-pin SCSI ports on the back of a
tape drive customer-replaceable unit (CRU).
background process. In the Open System Services (OSS) environment, a process that
belongs to a background process group.
background process group. In the Open System Services (OSS) environment, a process
group that is both:
•
Not a foreground process group
•
A member of a session that has a connection with a controlling terminal