NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index

Glossary
G-Series Common Glossary
Glossary-50
INSPSNAP
INSPSNAP. The program that provides a process snapshot file for the Inspect subsystem.
installation subvolume (ISV). A subvolume containing files that perform a specific function
during the installation process, such as organizing documentation in a specific location,
providing the components of the HP NonStop™ Kernel operating system image
(OSIMAGE), and containing files that are used after the installation process.
installer. The person who installs the system equipment for a new system. This person also
installs new equipment when additions are made to the system. This person can install
software and perform system verification procedures as directed by the system
planner, configuration planner, or support planner.
instruction processing unit (IPU). A processing unit that executes programs by fetching
instructions from memory and executing them.
insulated ground. A grounding conductor with a dielectric (low-conductance) insulator
around it to prevent inadvertent contact with metal conduits.
intelligent SCSI processor (ISP). The ServerNet addressable controller (SAC) that
controls the small computer system interface (SCSI) bus.
interactive mode. A mode of operation that is characterized by having the same input and
output device (a terminal or a process) for the session. If a terminal is used, a person
enters a command and presses Return. If a process is used, the system interface waits
for the process to send a request and treats the process in the same manner as a
terminal. Contrast with noninteractive mode
.
internal routing. The routing of packets within an HP NonStop™ S-series server. See also
external routing
.
internal ServerNet fabrics. The fabrics that link ServerNet devices within an HP
NonStop™ S-series server. See also external ServerNet fabrics
.
internal ServerNet X or Y fabric. The X or Y fabric that links ServerNet devices within an
HP NonStop™ S-series server. See also fabric
.
internationalization. The process of designing and coding software so that it can be
adapted to meet the needs of different languages, cultures, and character sets, with
the ability to handle various linguistic and cultural conventions. Internationalization
methods enable the processing of character-based data independently of the
underlying character encoding, allowing choice among character sets. Sometimes
referred to as
I18N, derived from the 18 letters between the initial I and the final N of
the word
internationalization. See also character set.
Internet address. The 32-bit address assigned to hosts that want to participate in the
Internet using Transmission Control Protocol/Internet Protocol (TCP/IP). Internet
addresses are an abstraction of physical hardware addresses, just as the Internet is an
abstraction of physical networks. As assigned to the interconnection of a host to a