NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index

Glossary
G-Series Common Glossary
Glossary-60
main service entrance
(PMF) customer-replaceable unit (CRU) and is cleared when the system is powered
off.
main service entrance. The enclosure containing connection panels and switchgear,
located at the point where the utility power lines enter the building.
Maintenance Interface. See Archive and Database Maintenance Interface.
maintenance switch. The Ethernet switch that links the maintenance entities in various
modular components to the HP NonStop™ Open System Management (OSM)
Interface.
management process. A process through which an application issues commands to a
subsystem. A management process can be part of a subsystem, or it can be
associated with more than one subsystem. In the latter case, the management process
is logically part of each subsystem. Subsystem Control Point (SCP) is the management
process for all subsystems controlled by Subsystem Control Facility (SCF).
manager. (1) For an HP NonStop™ system, the person responsible for day-to-day
monitoring and maintenance tasks associated with a software subsystem on a
NonStop node. (2) For a UNIX system, any person in Management and Information
Services management for the site.
man page. A term sometimes used in UNIX documentation for the online or hard-copy
version of a file that provides reference information. See reference page
.
master service processor (MSP). A service processor (SP) that provides the basic service
processor functions as well as centralized system functions such as a console port, a
modem port for remote support functions, and system-load control. The enclosure
containing processors 0 and 1 (group 01) also contains a pair of MSPs. See also
expansion service processor (ESP)
.
MB. See megabyte (MB).
Measure. A tool used for monitoring the performance of the HP NonStop™ servers.
Measure can be used to check the performance of a ServerNet cluster.
media access control (MAC) address. A value in the Medium Access Control sublayer of
the IEEE/ISO/ANSI local area network (LAN) architecture that uniquely identifies an
individual station implementing a single point of physical attachment to a LAN.
Media Interface Connector (MIC). A type of head on a fiber-optic cable that has locking
wings on the sides.
megabyte (MB). A unit of measurement equal to 1,048,576 bytes (1024 kilobytes). See also
gigabyte (GB)
, kilobyte (KB), and terabyte (TB).
member. In a structured programming language, an addressable entry within a data
structure. A member can be a simple field or a data structure.