NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index
Index
HP NonStop S-Series System Expansion and Reduction Guide—522465-009
Index-9
W
W
Worksheets
2.1a 4-2
, 4-6
2.n 4-5, 6-7
8a 4-2, 4-7
donor system 4-2
examples
10 3-9
, 3-10, 3-12, 3-13, 3-16
10, 11 3-7
5 2-9, 2-10, 2-11
list C-1
target system 6-6
using 2-9/2-14, 3-6/3-17
Z
ZSPR-EVT-
-CRU-INSERTION-FAILED 7-15
-CRU-INSERTION-OK 7-15
-CRU-POST-FAILED 7-9, 7-15
-CRU-POST-SUCCEEDED 7-9, 7-15
-CRU-REMOVED 7-15
-CRU-SNETCFG-COMPLETE 7-15
-CRU-SNETCFG-FAILED 7-15
-CRU-SNETCFG-STARTED 7-15
-LINK-ALIVE 7-15
ZSTO-EVT-
-ADAPTER-AUTO-FAILED 7-16
-ADAPTER-AUTO-RETRY 7-16
-CNFG-CRU-NOT-CONFIG 7-17
-CNFG-DISK-NAME 7-17
-CNFG-MISSING-CRU 7-17
-CONFIG-DEFERRED 7-17
-CRU-ACCESS-ERROR 7-17
-CRU-CONFIGURED 7-16
-CRU-CONFIG-FAILED 7-17
-CRU-DELETED 7-16
-CRU-INIT 7-9, 7-16
-CRU-INIT-FAILED 7-9, 7-16
-CRU-INSERTED 7-16
-CRU-OWNERSHIP 7-16
-CRU-RECONFIG 7-17
-CRU-REMOVED 7-16
-INVALID-CRU 7-16
-POST-COMPLETE 7-16
-POST-FAILED 7-16
-UNSUPPORTED-CRU 7-16
-WRONG-CRU-INSERTED 7-16