Safeguard Reference Manual (G06.29+, H06.08+, J06.03+)
Table Of Contents
- Safeguard Reference Manual
- Legal Notices
- Contents
- What is New in this Manual
- Manual Information
- New and Changed Information
- Changes to the 520618-030 manual
- Changes to the 520618-029 manual
- Changes to the 520618-028 manual
- Changes to the 520618-027 manual
- Changes to the 520618-026 manual
- Changes to the 520618-025 manual
- Changes to the H06.22/J06.11 manual
- Changes to the H06.21/J06.10 Manual
- Changes to the H06.20/J06.09 Manual
- Changes to the 520618-020 Manual
- Changes to the H06.19/J06.08 Manual
- About This Manual
- 1 Introduction
- 2 Common SAFECOM Language Elements
- 3 The Command to Run SAFECOM
- 4 SAFECOM Session-Control Commands
- 5 User Security Commands
- 6 User Alias Security Commands
- 7 Group Commands
- 8 Disk-File Security Commands
- Disk-File Ownership
- Disk-File Access Authorities
- Disk-File Access Authorization
- Disk-File Security Command Summary
- Syntax of Disk-File Security Commands
- ADD DISKFILE Command
- ADD DISKFILE-PATTERN Command
- ALTER DISKFILE Command
- ALTER DISKFILE-PATTERN Command
- DELETE DISKFILE Command
- DELETE DISKFILE-PATTERN Command
- FREEZE DISKFILE Command
- FREEZE DISKFILE-PATTERN Command
- INFO DISKFILE Command
- INFO DISKFILE-PATTERN Command
- RESET DISKFILE Command
- RESET DISKFILE-PATTERN Command
- SET DISKFILE Command
- SET DISKFILE-PATTERN Command
- SHOW DISKFILE Command
- SHOW DISKFILE-PATTERN Command
- THAW DISKFILE Command
- THAW DISKFILE-PATTERN Command
- SAFECOM Saved Diskfile Pattern Commands
- ADD SAVED-DISKFILE-PATTERN Command
- ALTER SAVED-DISKFILE-PATTERN Command
- DELETE SAVED-DISKFILE-PATTERN Command
- FREEZE SAVED-DISKFILE-PATTERN Command
- INFO SAVED-DISKFILE-PATTERN Command
- RESET SAVED-DISKFILE-PATTERN Command
- SET SAVED-DISKFILE-PATTERN Command
- SHOW SAVED-DISKFILE-PATTERN Command
- THAW SAVED-DISKFILE-PATTERN Command
- 9 Disk Volume and Subvolume Security Commands
- Volume Authorization Record Ownership
- Subvolume Authorization Record Ownership
- Volume and Subvolume Access Authorities
- Volume and Subvolume Access Authorization
- Volume and Subvolume Security Command Summary
- Syntax of Disk Volume and Subvolume Security Commands
- ADD VOLUME and SUBVOLUME Commands
- ALTER VOLUME and SUBVOLUME Commands
- DELETE VOLUME and SUBVOLUME Commands
- FREEZE VOLUME and SUBVOLUME Commands
- INFO VOLUME and SUBVOLUME Commands
- RESET VOLUME and SUBVOLUME Commands
- SET VOLUME and SUBVOLUME Commands
- SHOW VOLUME and SUBVOLUME Commands
- THAW VOLUME and SUBVOLUME Commands
- 10 Device and Subdevice Security Commands
- Device and Subdevice Authorization Record Ownership
- Device and Subdevice Access Authorities
- Device and Subdevice Access Authorization
- Device and Subdevice Security Command Summary
- Syntax of Device and Subdevice Security Commands
- ADD DEVICE and SUBDEVICE Commands
- ALTER DEVICE and SUBDEVICE Commands
- DELETE DEVICE and SUBDEVICE Commands
- FREEZE DEVICE and SUBDEVICE Commands
- INFO DEVICE and SUBDEVICE Commands
- RESET DEVICE and SUBDEVICE Commands
- SET DEVICE and SUBDEVICE Commands
- SHOW DEVICE and SUBDEVICE Commands
- THAW DEVICE and SUBDEVICE Commands
- 11 Process and Subprocess Security Commands
- Process and Subprocess Security
- Process and Subprocess Access Authorities
- Special NAMED and UNNAMED Process Protection Records
- Process and Subprocess Security Command Summary
- Syntax of the Process and Subprocess Security Commands
- ADD PROCESS and SUBPROCESS Commands
- ALTER PROCESS and SUBPROCESS Commands
- DELETE PROCESS and SUBPROCESS Commands
- FREEZE PROCESS and SUBPROCESS Commands
- INFO PROCESS and SUBPROCESS Commands
- RESET PROCESS and SUBPROCESS Commands
- SET PROCESS and SUBPROCESS Commands
- SHOW PROCESS and SUBPROCESS Commands
- THAW PROCESS and SUBPROCESS Commands
- 12 OBJECTTYPE Security Commands
- 13 Security Group Commands
- 14 Terminal Security Commands
- 15 Event-Exit-Process Commands
- 16 Safeguard Subsystem Commands
- 17 Running Other Programs From SAFECOM
- A SAFECOM Error and Warning Messages
- B Disk-File Access Rules
- Index
Safeguard Subsystem Commands
Safeguard Reference Manual — 520618-030
16 - 24
ALTER SAFEGUARD Command
The default value is OFF.
AUDIT-TACL-LOGOFF
controls generation of audits for the TACL LOGOFF or TACL EXIT operations.
When set to ON, audits for the TACL LOGOFF or TACL EXIT operations are
generated based on the value of the AUDIT-AUTHENTICATE-PASS and
AUDIT-AUTHENTICATE-FAIL attributes.
When set to OFF, audits for the TACL LOGOFF or TACL EXIT operations are
generated based on the value of the AUDIT-CLIENT-GUARDIAN, AUDIT-
PROCESS-ACCESS-PASS, and AUDIT-PROCESS-ACCESS-FAIL attributes.
The default value is OFF.
DYNAMIC-PROC-UPDATE
ON specifies that the process identity attributes (AUDIT-USER-ACTION-PASS,
AUDIT-USERACTION-FAIL, primary group, supplementary group list, and
group count) are updated dynamically when the audit and group attributes of
the corresponding user are modified.
The default value is OFF.
CI-PROG [ prog-filename ]
prog-filename defines the command interpreter st
arted after user
authentication at a Safeguard terminal if no command interpreter is defined for
the user or the terminal. The initial value is $SYSTEM.SYSTEM.TACL. A null
entry for this attribute sets the value to NONE. prog-filename must be a
local file name.
If CI-PROG is set to NONE, and no value is specified for CI-PROG for the
terminal or user, no command interpreter is started at the Safeguard terminal.
CI-LIB [ lib-filename ]
lib-filename defines the library file to be used with the CI-P
ROG command
interpreter specified in the Safeguard configuration record. The default value is
no library. A null entry for this attribute resets the value to the default value.
lib-filename must be a local file name.
Note. The attribute AUDIT-OSS-FILTER is supported only on systems running J06.04
and later J-series RVUs, H06.15 and later H-series RVUs, and G06.32 and later G-
series RVUs.
Note. The attribute AUDIT-TACL-LOGOFF is supported only on systems running
J06.08
and later J-series RVUs, H06.19 and later H-series RVUs, and G06.32 and
later G-series RVUs.
Note. The attribute DYNAMIC-PROC-UPDATE is suppo
rted only on systems running
J06.10 and later J-series RVUs and H06.21 and later H-series RVUs.