Safeguard Reference Manual (G06.29+, H06.08+, J06.03+)
Table Of Contents
- Safeguard Reference Manual
- Legal Notices
- Contents
- What is New in this Manual
- Manual Information
- New and Changed Information
- Changes to the 520618-030 manual
- Changes to the 520618-029 manual
- Changes to the 520618-028 manual
- Changes to the 520618-027 manual
- Changes to the 520618-026 manual
- Changes to the 520618-025 manual
- Changes to the H06.22/J06.11 manual
- Changes to the H06.21/J06.10 Manual
- Changes to the H06.20/J06.09 Manual
- Changes to the 520618-020 Manual
- Changes to the H06.19/J06.08 Manual
- About This Manual
- 1 Introduction
- 2 Common SAFECOM Language Elements
- 3 The Command to Run SAFECOM
- 4 SAFECOM Session-Control Commands
- 5 User Security Commands
- 6 User Alias Security Commands
- 7 Group Commands
- 8 Disk-File Security Commands
- Disk-File Ownership
- Disk-File Access Authorities
- Disk-File Access Authorization
- Disk-File Security Command Summary
- Syntax of Disk-File Security Commands
- ADD DISKFILE Command
- ADD DISKFILE-PATTERN Command
- ALTER DISKFILE Command
- ALTER DISKFILE-PATTERN Command
- DELETE DISKFILE Command
- DELETE DISKFILE-PATTERN Command
- FREEZE DISKFILE Command
- FREEZE DISKFILE-PATTERN Command
- INFO DISKFILE Command
- INFO DISKFILE-PATTERN Command
- RESET DISKFILE Command
- RESET DISKFILE-PATTERN Command
- SET DISKFILE Command
- SET DISKFILE-PATTERN Command
- SHOW DISKFILE Command
- SHOW DISKFILE-PATTERN Command
- THAW DISKFILE Command
- THAW DISKFILE-PATTERN Command
- SAFECOM Saved Diskfile Pattern Commands
- ADD SAVED-DISKFILE-PATTERN Command
- ALTER SAVED-DISKFILE-PATTERN Command
- DELETE SAVED-DISKFILE-PATTERN Command
- FREEZE SAVED-DISKFILE-PATTERN Command
- INFO SAVED-DISKFILE-PATTERN Command
- RESET SAVED-DISKFILE-PATTERN Command
- SET SAVED-DISKFILE-PATTERN Command
- SHOW SAVED-DISKFILE-PATTERN Command
- THAW SAVED-DISKFILE-PATTERN Command
- 9 Disk Volume and Subvolume Security Commands
- Volume Authorization Record Ownership
- Subvolume Authorization Record Ownership
- Volume and Subvolume Access Authorities
- Volume and Subvolume Access Authorization
- Volume and Subvolume Security Command Summary
- Syntax of Disk Volume and Subvolume Security Commands
- ADD VOLUME and SUBVOLUME Commands
- ALTER VOLUME and SUBVOLUME Commands
- DELETE VOLUME and SUBVOLUME Commands
- FREEZE VOLUME and SUBVOLUME Commands
- INFO VOLUME and SUBVOLUME Commands
- RESET VOLUME and SUBVOLUME Commands
- SET VOLUME and SUBVOLUME Commands
- SHOW VOLUME and SUBVOLUME Commands
- THAW VOLUME and SUBVOLUME Commands
- 10 Device and Subdevice Security Commands
- Device and Subdevice Authorization Record Ownership
- Device and Subdevice Access Authorities
- Device and Subdevice Access Authorization
- Device and Subdevice Security Command Summary
- Syntax of Device and Subdevice Security Commands
- ADD DEVICE and SUBDEVICE Commands
- ALTER DEVICE and SUBDEVICE Commands
- DELETE DEVICE and SUBDEVICE Commands
- FREEZE DEVICE and SUBDEVICE Commands
- INFO DEVICE and SUBDEVICE Commands
- RESET DEVICE and SUBDEVICE Commands
- SET DEVICE and SUBDEVICE Commands
- SHOW DEVICE and SUBDEVICE Commands
- THAW DEVICE and SUBDEVICE Commands
- 11 Process and Subprocess Security Commands
- Process and Subprocess Security
- Process and Subprocess Access Authorities
- Special NAMED and UNNAMED Process Protection Records
- Process and Subprocess Security Command Summary
- Syntax of the Process and Subprocess Security Commands
- ADD PROCESS and SUBPROCESS Commands
- ALTER PROCESS and SUBPROCESS Commands
- DELETE PROCESS and SUBPROCESS Commands
- FREEZE PROCESS and SUBPROCESS Commands
- INFO PROCESS and SUBPROCESS Commands
- RESET PROCESS and SUBPROCESS Commands
- SET PROCESS and SUBPROCESS Commands
- SHOW PROCESS and SUBPROCESS Commands
- THAW PROCESS and SUBPROCESS Commands
- 12 OBJECTTYPE Security Commands
- 13 Security Group Commands
- 14 Terminal Security Commands
- 15 Event-Exit-Process Commands
- 16 Safeguard Subsystem Commands
- 17 Running Other Programs From SAFECOM
- A SAFECOM Error and Warning Messages
- B Disk-File Access Rules
- Index
Safeguard Subsystem Commands
Safeguard Reference Manual — 520618-030
16 - 28
ALTER SAFEGUARD Command
ONLY
specifies that only pattern searching will occur. That is, normal non-pattern
searching will not be performed even if the pattern search returns
NORECORD.
MID
specifies that pattern based protection records will be searched:
°
After the diskfile protection record search returns NORECORD when
Direction-Diskfile is set to Filename-First.
°
Before the diskfile protection record search, when the Direction-Diskfile
is set to VOLUME-FIRST, and the VOLUME and SUBVOLUME
protection record search returns NORECORD.
AUDIT-CLIENT-OSS { ON | OFF }
specifies whether the OSS-related audits are written to the Safeguard audit
trial. It allows the auditing of OSS-related operations to be configured
independently of the existing AUDIT-CLIENT-GUARDIAN attribute, and all
other subsystem client auditing. The initial value is ON.
PASSWORD-ALGORITHM { DES | HMAC256 }
indicates the algorithm to encrypt passwords when they are changed. The
initial value is DES.
DES
indicates to use the DES algorithm to encrypt passwords. This is the initial
value. Encrypted passwords are stored in the L/USERID and L/USERAX
files.
HMAC256
indicates to use the HMAC with SHA-256 algorithm to encrypt passwords,
when PASSWORD-ENCRYPT is ON. Encrypted passwords are stored in
the L/USERAX files.
Note. The MID option is supported only on systems running J06.08 and later
J-series RVUs and H06.19 and later H-series RVUs.
Note. The AUDIT-CLIENT-OSS attribute is supported only on systems running
H06.0
8 and later H-series RVUs and G06.29 and later G-series RVUs.
Note. The PASSWORD-ALGORITHM attribute is supported only
on systems running
H06.06 and later H-series RVUs and G06.29 and later G-series RVUs.