Safeguard Reference Manual (G06.29+, H06.08+, J06.03+)
Table Of Contents
- Safeguard Reference Manual
- Legal Notices
- Contents
- What is New in this Manual
- Manual Information
- New and Changed Information
- Changes to the 520618-030 manual
- Changes to the 520618-029 manual
- Changes to the 520618-028 manual
- Changes to the 520618-027 manual
- Changes to the 520618-026 manual
- Changes to the 520618-025 manual
- Changes to the H06.22/J06.11 manual
- Changes to the H06.21/J06.10 Manual
- Changes to the H06.20/J06.09 Manual
- Changes to the 520618-020 Manual
- Changes to the H06.19/J06.08 Manual
- About This Manual
- 1 Introduction
- 2 Common SAFECOM Language Elements
- 3 The Command to Run SAFECOM
- 4 SAFECOM Session-Control Commands
- 5 User Security Commands
- 6 User Alias Security Commands
- 7 Group Commands
- 8 Disk-File Security Commands
- Disk-File Ownership
- Disk-File Access Authorities
- Disk-File Access Authorization
- Disk-File Security Command Summary
- Syntax of Disk-File Security Commands
- ADD DISKFILE Command
- ADD DISKFILE-PATTERN Command
- ALTER DISKFILE Command
- ALTER DISKFILE-PATTERN Command
- DELETE DISKFILE Command
- DELETE DISKFILE-PATTERN Command
- FREEZE DISKFILE Command
- FREEZE DISKFILE-PATTERN Command
- INFO DISKFILE Command
- INFO DISKFILE-PATTERN Command
- RESET DISKFILE Command
- RESET DISKFILE-PATTERN Command
- SET DISKFILE Command
- SET DISKFILE-PATTERN Command
- SHOW DISKFILE Command
- SHOW DISKFILE-PATTERN Command
- THAW DISKFILE Command
- THAW DISKFILE-PATTERN Command
- SAFECOM Saved Diskfile Pattern Commands
- ADD SAVED-DISKFILE-PATTERN Command
- ALTER SAVED-DISKFILE-PATTERN Command
- DELETE SAVED-DISKFILE-PATTERN Command
- FREEZE SAVED-DISKFILE-PATTERN Command
- INFO SAVED-DISKFILE-PATTERN Command
- RESET SAVED-DISKFILE-PATTERN Command
- SET SAVED-DISKFILE-PATTERN Command
- SHOW SAVED-DISKFILE-PATTERN Command
- THAW SAVED-DISKFILE-PATTERN Command
- 9 Disk Volume and Subvolume Security Commands
- Volume Authorization Record Ownership
- Subvolume Authorization Record Ownership
- Volume and Subvolume Access Authorities
- Volume and Subvolume Access Authorization
- Volume and Subvolume Security Command Summary
- Syntax of Disk Volume and Subvolume Security Commands
- ADD VOLUME and SUBVOLUME Commands
- ALTER VOLUME and SUBVOLUME Commands
- DELETE VOLUME and SUBVOLUME Commands
- FREEZE VOLUME and SUBVOLUME Commands
- INFO VOLUME and SUBVOLUME Commands
- RESET VOLUME and SUBVOLUME Commands
- SET VOLUME and SUBVOLUME Commands
- SHOW VOLUME and SUBVOLUME Commands
- THAW VOLUME and SUBVOLUME Commands
- 10 Device and Subdevice Security Commands
- Device and Subdevice Authorization Record Ownership
- Device and Subdevice Access Authorities
- Device and Subdevice Access Authorization
- Device and Subdevice Security Command Summary
- Syntax of Device and Subdevice Security Commands
- ADD DEVICE and SUBDEVICE Commands
- ALTER DEVICE and SUBDEVICE Commands
- DELETE DEVICE and SUBDEVICE Commands
- FREEZE DEVICE and SUBDEVICE Commands
- INFO DEVICE and SUBDEVICE Commands
- RESET DEVICE and SUBDEVICE Commands
- SET DEVICE and SUBDEVICE Commands
- SHOW DEVICE and SUBDEVICE Commands
- THAW DEVICE and SUBDEVICE Commands
- 11 Process and Subprocess Security Commands
- Process and Subprocess Security
- Process and Subprocess Access Authorities
- Special NAMED and UNNAMED Process Protection Records
- Process and Subprocess Security Command Summary
- Syntax of the Process and Subprocess Security Commands
- ADD PROCESS and SUBPROCESS Commands
- ALTER PROCESS and SUBPROCESS Commands
- DELETE PROCESS and SUBPROCESS Commands
- FREEZE PROCESS and SUBPROCESS Commands
- INFO PROCESS and SUBPROCESS Commands
- RESET PROCESS and SUBPROCESS Commands
- SET PROCESS and SUBPROCESS Commands
- SHOW PROCESS and SUBPROCESS Commands
- THAW PROCESS and SUBPROCESS Commands
- 12 OBJECTTYPE Security Commands
- 13 Security Group Commands
- 14 Terminal Security Commands
- 15 Event-Exit-Process Commands
- 16 Safeguard Subsystem Commands
- 17 Running Other Programs From SAFECOM
- A SAFECOM Error and Warning Messages
- B Disk-File Access Rules
- Index
SAFECOM Error and Warning Messages
Safeguard Reference Manual — 520618-030
A - 41
Effect. The command is not executed.
Recovery. PASSWORD-MAXIMUM-LENGTH should be greater than or equal to
PASSWORD-MINIMUM-LENGTH.
Cause. PASSWORD-ALGORITHM is HMAC256 and PASSWORD-ENCRYPT is ON
and PASSWORD-MAXIMUM-LENGTH is less than PASSWORD-MINIMUM-LENGTH.
Effect. The command is not executed.
Recovery. PASSWORD-MAXIMUM-LENGTH should be greater than or equal to
PASSWORD-MINIMUM-LENGTH.
Cause. An attempt to specify audit exclusion failed because the number of values
specified for the attribute AUDIT-EXCLUDE-VALUE was more than five.
Effect. The command is rejected.
Recovery. Specify five or lesser number of values for the attribute AUDIT-EXCLUDE-
VALUE.
Cause. An attempt to specify audit exclusion failed because both the attributes
AUDIT
-EXCLUDE-FIELD and AUDIT-EXCLUDE-VALUE were not set
Effect. The command is rejected.
Recovery. Specify values for both attributes AUDIT-EXCLUDE-FIELD and AUDIT-
EXCLUDE-VALUE in a single command line.
Note. This error message is supported only on systems running G06.31 and later G-series
RVUs and H06.08 and later H-series RVUs.
PASSWORD-MAXIMUM-LENGTH <n> MUST BE GREATER THAN OR EQUAL TO
PASSWORD-MINIMUM-LENGTH <n> ; COMMAND NOT EXECUTED
Note. This error message is supported only on systems running G06.31 and later G-series
RVUs and H06.08 and later H-series RVUs.
MAX AUDIT EXCLUDE VALUES 5 EXCEEDED
Note. This error message is supported only on systems running J06.03 and later J-series
RVUs, H06.14 and later H-series RVUs, and G06.32 and later G-series RVUs.
BOTH THE FIELDS AUDIT-EXCLUDE-FIELD and AUDIT-EXCLUDE-VALUE ARE REQUIRED
Note. This error message is supported only on systems running J06.03 and later J-series
RVUs and H06.14 and later H-series RVUs, and G06.32 and later G-series RVUs.