SSH Reference Manual
With this parameter set to false, users will be prompted if they want to continue a connection to an
unknown host.
Note: When you start SSH2 in NOWAIT mode, make sure you have disabled logging to the home terminal. To
do so, set the following PARAM:
PARAM LOGCONSOLE *
2. SSH2 will now start with the parameters specified in the command line. It will output initialization messages to
your terminal. Please check these messages for any errors.
Note: Set the DEFINE =TCPIP^PROCESS^NAME or the parameter SUBNET accordingly if you want to run SSH2
over a TCP/IP process other than $ZTC0.
Upon first startup, SSH2 will create a HOSTKEY for the DAEMON mode, which may take a few seconds, depending on
the speed of your system. SSH2 will also create the SSHCTL configuration data base.
Note: If you have installed SSH2 on a non-audited disk volume, SSH2 will fail to open the SSHCTL with error 80
(Invalid operation on audited file or non-audited disk volume). For testing, you may add SSHCTLAUDIT FALSE to the
startup parameters to work around this problem. For a production installation, however, it is strongly recommended that
you have SSHCTL audited. Use the SSHCTL parameter to specify a filename on an audited disk volume, if required.
A normal startup output looks similar to the following screen shot:
$SSH01|20Jan14 15:34:01.52|20|-------------------------------------------------------
$SSH01|20Jan14 15:34:01.52|10|SSH2 version T9999H06_22Jan2014_comForte_SSH2_0097
$SSH01|20Jan14 15:34:01.53|10|config file: '$QAHPSSH.T0801ABK.ztc1cfg'
$SSH01|20Jan14 15:34:01.53|10|config2 file: '*'
$SSH01|20Jan14 15:34:01.54|20|object filename is '\BWNS02.$QAHPSSH.T0801ABK.SSH2'
$SSH01|20Jan14 15:34:01.54|20|object subvolume is '\BWNS02.$QAHPSSH.T0801ABK',
priority is 150
$SSH01|20Jan14 15:34:01.54|20|dumping configuration:
[file ] * <log configuration>
[def ] ALLOWEDAUTHENTICATIONS <keyboard-interactive,password,publickey>
[file ] ALLOWEDSUBSYSTEMS <sftp,tacl>
[def ] ALLOWFROZENSYSTEMUSER <FALSE>
[def ] ALLOWINFOSSH2 <ALL>
[def ] ALLOWPASSWORDSTORE <TRUE>
[file ] ALLOWTCPFORWARDING <TRUE>
[def ] AUDITCONSOLE <*>
[file ] AUDITFILE <$QAHPSSH.T0801ABK.ZTC1AUD>
[file ] AUDITFILERETENTION <10>
[def ] AUDITFORMAT <21>
[file ] AUDITMAXFILELENGTH <1000>
[def ] AUTOADDAUTHPRINCIPAL <FALSE>
[file ] AUTOADDSYSTEMUSERS <TRUE>
[def ] BACKUPCPU <NONE>
[def ] BANNER <*>
[def ] BURSTSUPPRESSION <FALSE>
[def ] BURSTSUPPRESSIONEXPIRATIONTIME <300>
[def ] BURSTSUPPRESSIONMAXLOGLEVEL <40>
[def ] CACHEBURSTSUPPRESSION <FALSE>
[def ] CIPCOMPATERROR <*>
[def ] CIPHERS <aes256-cbc,twofish256-cbc,twofish-cbc,aes128-
cbc,twofish128-cbc,blowfish-cbc,3des-cbc,arcfour,cast128-cbc>
[def ] CLIENTALLOWEDAUTHENTICATIONS <none,gssapi-with-
mic,publickey,password,keyboard-interactive>
[file ] CLIENTMODEOWNERPOLICY <GUARDIANNAME>
[def ] COMPRESSION <TRUE>
[run ] CONFIG <$QAHPSSH.T0801ABK.ztc1cfg>
[def ] CONFIG2 <*>
[def ] CONSOLEBURSTSUPPRESSION <FALSE>
[def ] CPUSET <>
[def ] CUSTOMER <>
[file ] DAEMONMODEOWNERPOLICY <LOGINNAME>
[def ] DNSMODE <FIRST>
[def ] EMSBURSTSUPPRESSION <FALSE>
HP NonStop SSH Reference Manual Installation & Quick Start • 37