Release Notes HP Virtual TapeServer for NonStop Servers Product Version: 8.4 Rev. B October 2013 Part Number: 737701-001 © 2004 - 2013 Hewlett-Packard All rights reserved No part of this document may be copied in any form or by any means without prior written consent of HP. All drawings, schematics and artwork used in the manufacture of the products described herein are copyrighted.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Overview of features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Support. . . . . . . . . . . . . . . . . . . . . . . . . .
Known Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Hardware, configuration, and hardware replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 General operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Virtual TapeServer (VTS) is a fully integrated virtual tape, hardware and software solution. VTS offers complete disaster recovery capabilities. As a primary repository for data center backups, VTS can be used as secondary tiered storage for replicated data to meet disaster recovery requirements. Overview of features Release 8.4 introduces the following new features and support to VTS. Refer to online help for information about using any of the new features.
Installation and Configuration This section describes how to access information about installing and configuring release 8.4 of VTS. It also provides compatibility notes. Installation, upgrade, update, and downgrade The following documentation provides information about installing, upgrading, updating, and downgrading VTS: Initial installation and configuration is described in the Virtual TapeServerQuick Start Guide. Instructions to upgrade from 8.0, 8.2 or 8.3 to 8.
Host bus adapter support The following host bus adapters (HBAs) have been tested for use with VTS and IBM Power System servers: For use with Power 7: Feature code CCIN Description 0647, 1912, 5736, 5775 571A PCI-X DDR Dual Channel Ultra320 SCSI Adapter 5749 576B 4 Gigabit PCI-X2 Dual Port Fibre Channel Adapter 5774 5774 4 Gigabit PCI Express Dual Port Fibre Channel Adapter 5735 577D 8 Gigabit PCI-E Dual Port Fibre Channel Adapter Feature code CCIN Description 2765 2765 2 Gigabit Fi
Library Interface IBM TS3100 with LT04 and LTO-5 drives FC, SCSI IBM TS3100 with LTO-4 drives FC IBM TS3580 with LTO-3 drives FC Overland NEO with LTO-5 drives FC The following standalone drives were tested with Stacked Export jobs: Tape drive Interface HP Storageworks 960 Ultrium3 SCSI HP Storageworks 960 Ultrium3 FC The following standalone drives were tested with Tape-to-tape Export jobs (Host-native and Virtual formats): Tape drive Interface HP Storageworks 960 Ultrium3 FC HP Storage
Tape drive emulation VTS supports one virtual tape drive (VTD) per SCSI port and up to four VTDs per Fibre Channel port. All together, a maximum of 32 VTDs are supported per VTS server. For best performance, VTS can perform a maximum of 16 simultaneous backups at one time. Note Virtual tape drives support up to 256KB (262144 byte) blocks. Tape library emulation Multiple virtual tape libraries (VTLs) are supported per VTS system.
Supported Tape Library Emulations for IBM Systems TS3500-TD4-FC • Legacy Systems (v5r4, v5r4 M5) • Power6 (v5r4, v5r4 M5, v6r1, v6r1.1, v7r1) • Power7 (v6r1, v6r1.1, v7r1) TS3500-TD4-SCSI • Power6 (V6r1) Backup management application support Host connections are supported with the following backup applications: From Windows Server 2003 hosts: • IBM Tivoli Storage Manager 5.5 • Symantec Veritas NetBackup 6.5 and 7 • EMC RSA Legato Networker 7.5.2 • CommVault Galaxy 7.
Browser support The following browsers are supported for use viewing the VTS web interface: Microsoft Internet Explorer 7.0 and above Mozilla Firefox 4.
Upgrade and Downgrade This section provides procedures for upgrading and downgrading the VTS appliance(s) in your environment. It also provides a list of known issues related to upgrade and downgrade. Upgrading to 8.4 You can upgrade to 8.4 from version 8.0, 8.2 or 8.3 only. During the upgrade, a backup of /usr/ local/tape/ is created, the upgrade is performed, and new system RPMs are installed. After the upgrade completes, you can view the upgrade logs from the Manage Logs page of the web interface.
9. Select From Local File if you copied the .UPG file to the /tmp directory on the system or to an attached vault. Then, type the path in the Location of Revision Update File field. Or, select From Uploaded File and then click Browse to navigate to the file on the network or type in the full path of the location. 10. Click UPGRADE. 11. Click OK to continue. Note Upgrading may take a while. Do not navigate away from the page until the upgrade completes. 12.
Downgrading VTS Complete the following steps if you want to downgrade VTS (to 8.0, 8.2 or 8.3). The following is performed by the downgrade process: • Backup of /usr/local/tape/ is restored • System restore image is restored • VTS is downgraded • System restore image is deleted Note Operating system RPMs that were installed during an upgrade are not reverted. If desired, you must manually uninstall these RPMs. Also, it is recommended that you downgrade all appliances in your VTS environment.
Upgrade and downgrade issues Upgrade may fail because TapeServer process could not be stopped. Processes can be started intermittently by the web server (such as the System Status page) and cron jobs. If one of these processes runs a process from /usr/local/tape/bin during an upgrade, the upgrade could fail. (TL-5007, EAR-10253) WORKAROUND: Stop all processes using the service vts-services stop command and then attempt the upgrade again.
Resolved Issues and Enhancements The following changes have been incorporated into the software since the 8.3 release. Hardware, configuration, and hardware replacement In some instances, an IP Address could not be added to eth1 using the netconfig command. When the netconfig command was used to add the IP Address, “ip_addr undetermined” was returned. This issue has been resolved. (TL-8206) The netconfig command would not continue if a hardware error occurred on a disconnected port.
Jobs (general) A job name which contained a space or special characters would cause the job to fail with the error: “Missing backupSystem in jobset”. Now, any spaces in the name are converted to underscores when the job is saved. Special characters are not allowed in job names. (TL-7736, EAR-9006) Manage Virtual Tapes and Manage Tapes and Pools (Advanced Operations) The Data Size column of the Virtual Tapes pages reported 0 Bytes in use for all cartridges.
VTL Entering a VTL serial number larger than 10 digits caused the creation of the VTL to fail. The input field for the VTL serial number is now limited to 10 digits. (TL8195) A tape that was moved from a drive to the I/O port in a VTL, would only be partially removed from the VTL and would be unusable afterwards. Now, the tape will be moved out of the VTL and placed on the shelf where the I/O Port leaves it.
Policy Based Actions If a pool had multiple policies defined, only the first policy triggered would run. This issue has been resolved. (TL-8210, EAR-10654) When a pool was renamed the policies associated with the pool were not transferred to the updated pool. This issue is no longer seen in version 8.4. (TL-7897) AutoCopy, Instant DR, and Replication If an IDR job was run with the incorrect job name, the message: “Missing backup System” was erroneously reported.
Utilities and services Each hour multiple entries were written to the var/log/messages log concerning automounts. The entries were similar to: “Mar 17 16:01:12 vtslibg4 automount[5209]: create_udp_client:90: hostname lookup failed: Operation not permitted”. This issue has been resolved. (TL-7335, EAR-10347, EAR-9583) The error “ERROR> keepalive.cgi:170 keepalive - The indicated process is not running” appeared in the job log after a job successfully completed. This issue has been resolved.
Known Issues The following known issues, or “errata,” apply to the 8.4 release. The issue tracking number is provided in parentheses. Refer to this number when making inquiries to Technical Support. There is a table of tracking numbers listed in ascending order, with the summary and document section number, in Issue Index on page 55. Hardware, configuration, and hardware replacement Adding or removing a HBA may cause the port configuration to change.
Connection issues may occur when using 4Gb Fibre Channel cards. Connection issues can occur when using the 4Gb Fibre Channel card directly connected to AS/400 on v5r4. When it comes up as private loop, there are issues seeing the devices. Also, if the host resets, VTS runs out of resources in the driver and the VTD is lost. Contact Support if this issue occurs. (TL-6698, EAR-7772, EAR-7918, EAR-9416) Compression setting for tape drives is not altered from the default value after it has powered on.
No checks are made for duplicate file names when moving a virtual cartridge from a /DATAxx partition to a /VAULTxx partition. This may cause issues if the same filename is used in different VAULTs or pools. (TL-8236) vtsa user cannot mount CD or DVD. The vtsa user is not able to execute mount commands. (TL-6748) WORKAROUND: Use the bill user instead. Incorrect serial number of SCSI VTD is displayed in the System Tools menu with V7iOS (V7R1).
• ems_telnet.pl • hsmdelete.pl • hsmget.pl • hsmput.pl • vtsisc_cancel.pl • vtsisc_mount.pl • vtsisc_unmount.pl • vts_scratch_erase.pl The most common symptom of this problem is that VTS will not be able to log into a host server. Log messages may make it appear as if a password has not been set, though it has been set since encrypted passwords cannot be decrypted.
To disable ISC, two parameters must be set. The ems_InterSystemCommunication_hosts and interSystemCommunication_enable parameters must be set to indicate that ISC should be disabled. Otherwise, ISC will still be enabled. (TL-0240) WORKAROUND: To disable ISC, set these parameters in the VTS configuration file: interSystemCommunication_enable=”NO” ems_InterSystemCommunication_hosts=”ems_InterSystemCommunication_host s=”” Then, stop ISC from the Manage System Tasks page.
Editing a VTD without a license causes the VTD to be deleted. If the license is removed and then you attempt to edit a VTD, the system deletes the VTD. (TL-3962) Tape can be mounted in deleted VTD and the tape remains locked. If you delete a VTD, VTS still allows you to mount a virtual tape in the deleted VTD. No data is lost but the tape is locked. This occurs if multiple windows are used and actions are performed in one window and affect the actions taken in the other.
System Status page indicates that TEST_UNIT_READY command was processed and complete, but no commands were processed. The System Status page indicates that a TEST_UNIT_READY command was completed. If the user looks at this to determine if VTS is communicating with the host, it is misleading. The TEST_UNIT_READY command is command 0x0.
A pool can not be moved to a different vault using the Tapes and Pools page. The help for the Tapes and Pools page incorrectly states that you can change the name for any field except the pool name. The help should state that you can change the name for any field except the VAULT name. (TL-8269, EAR-10250) The Last Mounted column on the Manage Virtual Tapes page shows the last time the virtual tape was modified, not necessarily the last time the virtual tape was mounted.
Cartridge size check done on Cartridge Maintenance page instead of Pool Maintenance page. Though you specify a maximum cartridge size on the Pool Maintenance page, the system does not check for the size; it checks on the Cartridge Maintenance page. (TL-3772) Cannot click button to confirm deletion of cartridges if deleting many. When deleting many cartridges, the confirmation dialog box extends off the screen and does not show the OK button.
Firefox improperly renders Cartridge Maintenance page when Multiple Select checkbox is unchecked. If you use Firefox to view the interface and you deselect the Multiple Select option on the Cartridge Maintenance page, the browser renders the page incorrectly, displaying items in the wrong place and not preserving information. (TL0346) WORKAROUND: Click the Clear Form button to correct the display problem. Pool is restored to a cartridge resulting in data not being stored as expected.
VTL may be loaded with too many cartridges. When a VTL is edited and more virtual tapes are placed in the VTL than number of slots available, the library may fail to startup and remain in the disabled state. (TL-3624) Unmount button for virtual tapes in a virtual library does not work. You cannot manually unmount a virtual tape that resides in a virtual library. (TL-1384) WORKAROUND: Use the Manage Virtual Tapes page and remove the cartridge from the VTL instead of trying to unmount it.
Filter by Pool drop-down list on the External Data page is disabled if a pool with no replicated tapes is selected. If a pool has no replicated virtual tapes, the Filter By Pool drop-down list is disabled if selected. Use this feature only when there are virtual tapes to be displayed. (TL-6755) WORKAROUND: Navigate away and then back to the External Data page. Selecting Back button on External Data page does not allow drop-down devices to be selected directly.
PTLI reservation is unclear and may cause error. If you change a port from physical to virtual mode, an error is displayed if you attempt to create a virtual device on the port where that physical drive was connected. The reservation of the PTLI is a feature, but the reason for it may not be clear and the method to clear it up is not indicated by the error message. (TL-5946) WORKAROUND: Delete the PTLI using the Advanced link on the Manage Virtual Devices page.
Reports No destination given in Export Report. If an error occurs while connecting to a remote host or device, the Export report will not indicate this though the export fails. (TL6312) Access Control A user with an Operator account cannot perform any jobs on the media from the Virtual Media Management page regardless of the permissions granted under Access Control. (TL-8554) WORKAROUND: Use the Advanced pages to perform these jobs.
VTL Modifying the number of slots within a VTL may cause the VTL to fail. (TL-8534) WORKAROUND: If the number of slots within a VTL needs to be modified, remove and recreate the VTL. For VTL drives, the eject button on the drives page will be visible, but not usable. Attempting to use the eject button to eject a tape from a VTL drive will fail as expected since the drives are controlled by the changer.
Incorrect error message displayed if attempting to add locked cartridge to library. If the library is full when adding a cartridge to a library, check the Mounts and Locks page to determine if the cartridge is locked. If so, you may receive this message: “Unable to insert cartridge because magazine is full.” A locked cartridge cannot be added to a library, but the error message is incorrect in this case. (TL-4004) WORKAROUND: Resolve the locked condition and then add the cartridge to the library.
without all library entities (including Logical and Physical) associated with the Library definition deleted, the web interface and backend protocol layers become inconsistent. (TL-2318) WORKAROUND: Remove all associated library objects (including Physical and Logical), edit the file again, and recreate the library. VLM cannot be loaded if a pool is moved. The full path to a virtual tape is used when the virtual tape is added to a VLM.
No notification that restore fails because remote key server was not added after restoring from a disaster recovery site. The local key server should be removed prior to restoring the key database. The web interface should notify the user when a restore from a disaster recovery site fails because a local key server already exists. (TL-4399) Key database restore fails if an IP address is used instead of a hostname.
Creating cartridges in an encrypted pool when Data Encryption is not running generated confusing message. If Data Encryption is not running and you attempt to create cartridges in an encrypted pool, messages similar to the following are displayed. (TL-3048) Created 0 of 10 in P17 of size 2T successfully: Cartridge BBB000 in P17 failed encryption rc=254 Errors are logged to encry_key.log during exports and uploads. During exports and uploads, messages similar to the following are logged to encry_key.
Removing a key generator may cause a delay before cartridges can be encrypted again. After removing a key generator, if there are any key generators left, it may take up to 5 minutes before cartridges can be encrypted again. (TL-1121) If the RSA key of a remote host changes, Data Encryption operations to that host may fail. Typically, the RSA key will not change unless the operating system on that host is reinstalled.
VTSPolicy commands Q_INC and Q_DIFF variables used in the CommVault VTSPolicy backup all cartridges. Q_INC and Q_DIFF variables used in the CommVault VTSPolicy should backup the changed cartridges since the last backup. Instead, all cartridges all in the pool are backed up. (TL-2770) VTSPolicy TSM Archive command for a vault results in an error message. Issuing a VTSPolicy TSM Archive command for a vault will fail to back up the vault.
Cartridge having less than minimum size is listed as erasable in Scan/Cleanup after migration. If a cartridge is below the size specified by the cleanup_minimum_size_ MB parameter, the cartridge is scheduled to be erased by Scan/Cleanup after migration. This is incorrect behavior; it should not be scheduled for erasure. (TL-0444) Tape-to-tape export and import (native export and import) No warning is given if a job is scheduled without selecting a cartridge.
Virtual tape is skipped during a Tape-to-Tape export if it is empty. When selecting a virtual tape for Tape-to-Tape export to a library, and the virtual tape is empty, the export is not performed with the message that there is no data in the tape (even if the “Virtual Tape Format” is chosen). (TL-6540) WORKAROUND: Add data to the VT to export it. Activity log on Import/Export page is not in chronological order. The log messages are listed in random order.
Stack Exports triggered as events may fail. Stack Exports triggered as policy events may fail because there is no delay between backups. (TL-7818) WORKAROUND: Use the Job Scheduler to schedule Stacked Exports instead of Stacked Export policy events. Stacked and remote exports cannot be canceled using the UI. Once they have started, stacked and remote exports cannot be canceled using the UI. (TL-8007) In order for a stacked export to succeed, enough resources must be available.
Error, miscellaneous messages logged after successful NetBackup migration. Message similar to the following are logged in the debug log after a successful migration with NetBackup 6.5: Fri Nov 7 14:45:27 2008: [slave_signal_thread 15713] SIGCHLD received while no active child, ignoring it. Fri Nov 7 14:45:32 2008: [cli_tape 0x05000107] ERROR UNKNOWN tape command 0x44 for Id 0 Fri Nov 07 14:46:15 2008: [lsof.pl] Error: lsof.
Backup Exec 2012 incorrectly reports VT sizes for SDLT and DLT7000. Backup Exec 2012 incorrectly reports VT sizes for SDLT and DLT7000 tapes. Blank VTs show up with 16MB of free space. Tapes with data report the wrong amount of space left and space used. (TL-8063) WORKAROUND: Use the Ultrium, or Ultrium 3-SCSI drive types for correct tape usage. Restoring individual files from export that spanned files using CA ARCserve fails. (TL-6517) WORKAROUND: Restore the entire backup to obtain the single file.
Replicate job to missing or remounted data location gives vague error message. If a data location is remounted to an alternate mount point or removed, the error message from a replicate job that should use this location does not indicate the cause. Note that after a data partition has been used, it is not supported to remove it nor to change its mount point. (TL-5859) Status of replication job that failed due to an error is displayed as cancelled.
Virtual tapes are split though target vault is invalid. A virtual tape is split into multiple streams during a remote export even when the target vault is invalid. Once the file is split, replication will fail due to the vault being invalid. It should detect the error before splitting the file. (TL-4267) Rebooting while Replication is splitting files leaves a running job.
EMS If ems_keep_alive_interval is set too small, a “keep-alive lost!” message is generated. If the ems_keep_alive_interval is set too small, a very large number of Event Monitoring System (EMS) messages may be queued. This could result in a “keep-alive lost!” message being generated. (TL-8124) WORKAROUND: To avoid this keep the value of the ems_keep_alive_interval parameter just smaller than the timeout value for telnet or SSH depending on which is being used for EMS.
If a mount command is sent to a non-existent virtual tape drive, VTS reports that the tape is missing, not the drive. When a mount request is received by EMS, if the request specifies a tape drive that is not configured on the VTS, VTS sends a notification to the host that the tape is not found. It should send a notification that the drive is not found. (TL-2293) SMTP and notifications SMTP Delivery settings can be saved with no SMTP Server set.
Error message in vts-post-install.log. The message is a result of trying to change mode on a directory that does not yet exist: chmod: cannot access `/var/log/crds/rath_manager.log': No such file or directory. This message can be ignored. (TL-7380) Fatal message in vts-post-install.log. This message is a result of stopping the cpuspeed service which is intentional: - FATAL: Could not load /lib/modules/2.6.18-92.el5/modules.dep: No such file or directory. This message can be ignored.
cp: cannot stat `/usr/local/tape/patch': No such file or directory ls: /vault: No such file or directory WORKAROUND: Use the button on the web interface to obtain the logs. Message logged to console and /var/log/messages until iLO is configured. Until HP-iLO is configured, the following message may continue to print: INIT: Id “s1” respawning too fast: disabled for 5 minutes The message is also logged to /var/log/messages with no other information.
Troubleshooting This section includes information about how to troubleshoot problems and notes about items that may need clarification. Hardware, configuration, and hardware replacement IBM iSeries v7r1 does not discover VTLs when MF52479 PTF is applied. This is realized by the failure of the strsst (menu options 1,7,2,1) failing to show tape library devices. It is recommended that this PTF not be applied to avoid losing the detection and operation of physical and virtual changers.
General operations If a cartridge contains the maximum amount of data, encrypting the cartridge will cause the cartridge limit to be exceeded. However, no error is given to indicate this situation. The cartridge can be exported but if it is imported to a cartridge of the original cartridge limit size, the import will fail. (TL-1168) WORKAROUND: Import the cartridge to a cartridge whose size is larger than the original cartridge limit size. The portmap service is turned off by default.
Error message displayed on console after the system is booted for the first time. Messages similar to the following are displayed on the console the first time VTS is booted: Mounting other filesystems: [ OK ] Starting hp-ilo:/opt/hp/hp-ilo/drivers/char/hp_ilo/CpqCiKlx.c: In functionoctl32_handler': /opt/hp/hp-ilo/drivers/char/hp_ilo/CpqCiKlx.c:680: warning: assignment makes pointer from integer without a cast /opt/hp/hp-ilo/drivers/char/hp_ilo/CpqCiKlx.
Web interface Virtual tapes cannot be renamed. You cannot rename a virtual tape. (TL-4414, EAR6411) WORKAROUND: Create new virtual tapes with the desired name using the Advanced Media Actions option on the Manage Virtual Tapes page. Changing tape library settings could cause the drives to be unusable. When a tape library was changed from random access mode to auto loader mode, the Physical Device settings could become confused.
Data Encryption (SecureVTS) Tape library must be configured for encryption to support export of encrypted tapes. The external tape library must be correctly configured to allow VTS to manage encryption. Refer to the library documentation for instructions. (TL-6435) When encrypting or decrypting a cartridge and TapeServer stops, temporary directory and file are not deleted. Do not stop TapeServer or restart VTS unless the system is quiesced.
AutoCopy An error message from ems_telnet.pl indicates that AutoCopy is not configured. For AutoCopy to work as designed, manual procedures that mount a tape must end with unmounting the tape. AutoCopy depends on receiving mount and unmount messages through EMS to work correctly, and when a tape is manually mounted, the EMS subsystem is unaware of this. When the manual operation is completed, the tape must be unmounted manually.
Issue Index EAR-4030 EAR-4286 EAR-4456 EAR-4912 EAR-6219 EAR-6359 EAR-6411 EAR-7149 EAR-7280 EAR-7622 EAR-7672 EAR-7772 EAR-7918 EAR-8107 EAR-8148 EAR-8490 EAR-8795 EAR-9006 EAR-9049 EAR-9117 EAR-9416 EAR-9438 EAR-9460 EAR-9472 EAR-9583 EAR-9594 EAR-9655 EAR-10250 EAR-10253 EAR-10333 EAR-10347 EAR-10390 Using device names beginning with $ resulted in the values for ems_hostdevs and ems_virtdevs being blank in the logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EAR-10452 If an Instant Data Replication (IDR) job was started from the IDR user interface or an Event Management System (EMS) policy, an email notification may not have been sent when the IDR job completed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAR-10543 Cartridges might have remained in a locked state after being erased which resulted in the process failing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-0386 TL-0434 TL-0444 TL-0505 TL-0515 TL-0570 TL-0868 TL-0880 TL-0881 TL-0930 TL-0941 TL-0951 TL-0970 TL-0977 TL-0984 TL-0996 TL-1001 TL-1033 TL-1035 TL-1039 TL-1041 TL-1051 TL-1056 TL-1073 TL-1074 TL-1088 TL-1107 TL-1121 TL-1136 TL-1158 TL-1168 TL-1205 TL-1206 TL-1239 TL-1384 TL-1480 Unable to unmigrate a pool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pool Maintenance page loads slowly in a clustered environment.. . . . . . . . . . . . . . . . . .
TL-1526 TL-1562 TL-1662 TL-1752 TL-1755 TL-1802 TL-1804 TL-1836 TL-1844 TL-1853 TL-1869 TL-1886 TL-1903 TL-1920 TL-1962 TL-1997 TL-2061 TL-2063 TL-2079 TL-2086 TL-2155 TL-2158 TL-2179 TL-2189 TL-2201 TL-2255 TL-2272 TL-2279 TL-2280 TL-2287 TL-2292 TL-2293 TL-2303 TL-2317 TL-2318 TL-2320 TL-2324 TL-2342 TL-2347 VLM cannot be loaded if a pool is moved. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-2350 TL-2358 TL-2365 TL-2367 TL-2388 TL-2390 TL-2529 TL-2551 TL-2629 TL-2641 TL-2770 TL-2772 TL-3001 TL-3020 TL-3032 TL-3041 TL-3048 TL-3052 TL-3071 TL-3105 TL-3117 TL-3125 TL-3152 TL-3156 TL-3165 TL-3168 TL-3170 TL-3171 TL-3175 TL-3190 TL-3212 TL-3278 TL-3300 TL-3304 TL-3377 TL-3429 TL-3440 TL-3456 TL-3463 Cartridge Status pop-up dialog is not updated while a cartridge is mounted. . . . . . . . . 25 Scan/Cleanup page performance is slow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-3491 TL-3512 TL-3515 TL-3562 TL-3624 TL-3643 TL-3672 TL-3702 TL-3721 TL-3742 TL-3756 TL-3766 TL-3772 TL-3788 TL-3825 TL-3837 TL-3844 TL-3847 TL-3849 TL-3853 TL-3874 TL-3877 TL-3885 TL-3897 TL-3940 TL-3950 TL-3953 TL-3962 TL-3982 TL-3985 TL-4004 TL-4007 TL-4011 TL-4012 TL-4014 TL-4018 TL-4033 TL-4035 TL-4042 TL-4046 TL-4063 TL-4108 TL-4139 TL-4141 TL-4142 TL-4163 TL-4176 Manage Virtual Devices page does not select available values when creating VTDs. . .
TL-4199 TL-4232 TL-4260 TL-4265 TL-4267 TL-4286 TL-4287 TL-4299 TL-4308 TL-4313 TL-4326 TL-4371 TL-4391 TL-4398 TL-4399 TL-4414 TL-4429 TL-4434 TL-4439 TL-4447 TL-4456 TL-4464 TL-4466 TL-4469 TL-4513 TL-4533 TL-4536 TL-4607 TL-4616 TL-4620 TL-4669 TL-4670 TL-4779 TL-4806 TL-4822 TL-4857 TL-4859 TL-4922 TL-4940 TL-4953 Mounts and unmounts appear to succeed though file system is full and failure code is returned. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-4956 TL-5007 TL-5023 TL-5034 TL-5063 TL-5111 TL-5137 TL-5155 TL-5177 TL-5179 TL-5207 TL-5246 TL-5252 TL-5456 TL-5582 TL-5586 TL-5677 TL-5698 TL-5707 TL-5738 TL-5741 TL-5806 TL-5844 TL-5845 TL-5850 TL-5859 TL-5862 TL-5882 TL-5892 TL-5930 TL-5944 TL-5946 TL-5948 TL-5951 TL-5954 TL-5969 TL-5971 TL-5975 Performance slows and the web interface becomes unresponsive if you close the browser during a pool move. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-5976 TL-5980 TL-5982 TL-5988 TL-5990 TL-5997 TL-5998 TL-6004 TL-6110 TL-6117 TL-6135 TL-6191 TL-6260 TL-6263 TL-6279 TL-6312 TL-6376 TL-6384 TL-6388 TL-6429 TL-6435 TL-6489 TL-6517 TL-6530 TL-6540 TL-6548 TL-6564 TL-6598 TL-6604 TL-6606 TL-6616 TL-6628 TL-6646 TL-6651 TL-6697 TL-6698 TL-6708 TL-6723 TL-6736 TL-6741 TL-6748 TL-6755 Replication lock files left on destination system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-6757 TL-6773 TL-6777 TL-6817 TL-6820 TL-6832 TL-6835 TL-6862 TL-6866 TL-6874 TL-6915 TL-6982 TL-6984 TL-7003 TL-7031 TL-7117 TL-7160 TL-7179 TL-7212 TL-7247 TL-7256 TL-7266 TL-7272 TL-7300 TL-7311 TL-7320 TL-7325 TL-7326 TL-7333 TL-7335 TL-7336 TL-7340 TL-7343 TL-7346 TL-7350 TL-7362 TL-7363 TL-7367 TL-7370 TL-7372 TL-7374 TL-7378 Encryption option is displayed for a disconnected library with drives that do not support encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-7379 TL-7380 TL-7381 TL-7391 TL-7392 TL-7406 TL-7409 TL-7453 TL-7494 TL-7531 TL-7550 TL-7586 TL-7595 TL-7599 TL-7608 TL-7610 TL-7611 TL-7617 TL-7625 TL-7632 TL-7641 TL-7697 TL-7725 TL-7736 TL-7750 TL-7783 TL-7812 TL-7813 TL-7814 TL-7818 TL-7896 TL-7897 TL-7918 TL-7934 TL-7940 TL-7944 TL-7967 TL-7988 TL-7994 Fatal message in vts-post-install.log.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Error message in vts-post-install.log. . . . . . . . . . . . . . . . . . . . .
TL-7996 TL-8007 TL-8026 TL-8034 TL-8046 TL-8063 TL-8082 TL-8094 TL-8095 TL-8098 TL-8099 TL-8112 TL-8114 TL-8123 TL-8124 TL-8137 TL-8154 TL-8178 TL-8187 TL-8188 TL-8195 TL-8206 TL-8210 TL-8234 TL-8236 TL-8269 TL-8349 TL-8358 TL-8365 TL-8368 TL-8374 TL-8405 TL-8429 The status of tapes shown in the Virtual Tapes page may not be current . . . . . . . . . . . Stacked and remote exports cannot be canceled using the UI. . . . . . . . . . . . . . . . . . . . .
TL-8445 TL-8449 TL-8454 TL-8456 TL-8460 TL-8481 TL-8493 TL-8507 Tl-8525 TL-8534 TL-8545 TL-8554 TL-8557 TL-8571 TL-8575 A pool which contained a large number of virtual tapes took longer than expected to be displayed on the Virtual Tapes page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 The size of the cluster vaults reported in the systems web interface was rounded down to the nearest whole number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index of Resolved Issues by Release 8.4 TL-1088 TL-1562 TL-1844 TL-1903 TL-2320 TL-3001 TL-3041 TL-3125 TL-4018 TL-4371 TL-5137 TL-0515 TL-6489 TL-6548 TL-6832 TL-6984 TL-7117 TL-7335 TL-7362 TL-7363 TL-7367 TL-7453 TL-7494 TL-7617 TL-7736 Empty, unlabeled encrypted cartridges might have shown a compression ratio.. . . . . . . Using device names beginning with $ resulted in the values for ems_hostdevs and ems_virtdevs being blank in the logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TL-7783 TL-7897 TL-8095 TL-8099 TL-8112 TL-8123 TL-8154 TL-8178 TL-8187 TL-8188 TL-8195 TL-8206 TL-8210 TL-8349 TL-8358 TL-8365 TL-8368 TL-8405 TL-8429 TL-8445 TL-8449 TL-8454 TL-8460 TL-8481 TL-8493 The Data Size column of the Virtual Tapes pages reported 0 Bytes in use for all cartridges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
