XYGATE Access Control Reference Manual

XYGATE
®
Access Control Reference Manual
Appendix G: XAC Error Messages
XYPRO Technology Corporation 282 Proprietary and Confidential
Error Message Description
XAC – ACACL syntax error at line ##
- Command <ACL Command Name>
Missing CHANGERUSER FROM or
TO specification
No more than a total of 10,000 bytes of arguments can be used with all the
INPUT keywords used in a single ACACL entry
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
Too many entries for PROMPT
The CHANGEUSER_FROM and CHANGEUSER_TO keywords must be
used together; both must be present in an ACACL entry if either one is
present.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
ALIAS table overflow
You are permitted to have a maximum of 10 different tokens in your prompt
line.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
ALLOW/DENY quote mismatch
The command indicated caused the total byte count of arguments to the
ALIAS keyword for all entries in the ACACL file to exceed 10,000 bytes.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
ALLOW/DENY table overflow
The argument to ALLOWCMD or DENYCMD must have both beginning and
ending quotation marks.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
CONVMODE fkeys must be defined
before BLOCKMODE FKEYS <key
name>
No more than 200 separate ALLOWCMD and DENYCMD entries are
permitted in the entire ACACL file. No more than 10,000 bytes total of
arguments to the ALLOWCMD and DENYCMD entries are permitted in the
entire ACACL file.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
Duplicate objects specification not
allowed
All MAP_C_FKEY commands in a single ACACL Command Entry must
occur before all MAP_B_FKEY commands in that same ACACL Command
Entry,.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
FKEY from error
OPENSBYOBJECTS can only occur once in a Command Entry in the
ACACL file.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
FKEY to error
The ORIGINAL key name specified in the command is in error; it must be
F1-F16, SF1-SF16, PGDN, SPGDN, PGUP, SPGUP, LNINS, LNDEL, ENT,
SENT, RLUP, SRLUP, RLDN, SRLDN or the special value ALL.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
INPUT table overflow
The MAP-TO key name specified in the command is in error; it must be F1-
F16, SF1-SF16, PGDN, SPGDN, PGUP, SPGUP, LNINS, LNDEL, ENT,
SENT, RLUP, SRLUP, RLDN, SRLDN or the special value NONE.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
Invalid PROMPT keyword <text>
The arguments to the INPUT keyword exceed 10,000 characters; 10,000
characters is the maximum permitted.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
PROMPT text limit exceeded
The PROMPT entry included <text> which is not a valid keyword.
XAC – ACACL syntax error at line ##
- COMMAND <Command Name>
Too many CHANGEUSER entries
Your prompt, once built and including the text of all the PROMPT keywords
you included on the line, may not exceed 20 characters in length.
XAC – ACACL syntax error at line ##
- Duplicate ACLGROUP ignored -
<ACLGROUP name>
No more than 10 CHANGEUSER FROM/TO pairs may be assigned to a
single ACACL Command Entry.
XAC – ACACL syntax error at line ##
- Missing ACLGROUP name
The same name is used for two different ACLGROUP entries; change the
name.