McDATA® 4Gb SAN Switch for HP p-Class BladeSystem user guide Part number: AA-RW20B-TE Second edition: December 2005
Legal and notice information © Copyright 2005 Hewlett-Packard Development Company, L.P. © Copyright 2005 McDATA Corporation. © Copyright 2005. This software includes technology under a license from QLogic Corporation. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create Security Group dialog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Create Security Group Member dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Editing the security configuration on a switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viewing properties of a security set, group, or member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a zone set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activating and deactivating a zone set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing a zone from a zone set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing a zone set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Managing zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring the factory default configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Downloading a support file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing Product Feature Enablement (PFE) keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Port command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Setup command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Show command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Show Config command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40 41 42 43 44 45 46 47 48 Network Properties dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SNMP Properties dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Restore dialogs – Full Restore and Selective Restore tab pages . . . . . . . . . . . . . . Features Licenses dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add License Key dialog . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This manual describes the McDATA® Web Server™ and McDATA Element Manager™ management tools for the McDATA 4Gb SAN Switch. The McDATA 4Gb SAN Switch is a 10-port non-blocking Fibre Channel (FC) switch. This manual defines the features, components, and performance characteristics of the McDATA 4Gb SAN Switch.
Document conventions and symbols Table 1 Document conventions Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text (http://www.hp.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the disclaimer that follows these conditions in the documentation and/or other materials provided with the distribution. 3. The name "JDOM" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact license@jdom.org. 4.
Helpful web sites For other product information, see the following HP web sites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.com • http://h71028.www7.hp.com/enterprise/cache/80316-0-0-0-121.
1 Using McDATA Web Server/McDATA Element Manager This section describes how to use the McDATA Web Server and McDATA Element Manager applications and their menus. McDATA Web Server is a graphical user interface that provides both fabric and switch module management functions. Because McDATA Web Server resides in the switch firmware, no installation is needed. You can run one instance of the McDATA Web Server at a time by opening the switch IP address with an internet browser.
Table 2 Workstation requirements Hardware RJ-45 Ethernet port Internet Browser Microsoft® Internet Explorer® 5.0 or later Netscape® Navigator® 4.72 or later Mozilla™ 1.02 or later Java 2 Run Time Environment installed to support the McDATA Web Server. See Starting McDATA Web Server, page 14 for more information. Starting McDATA Web Server To start McDATA Web Server after the switch is operational, enter the switch IP address in an internet browser.
Perform one of the following procedures to access and begin managing the switch: • Select Open Existing Fabric to open the Add a New Fabric dialog, which prompts you for a fabric name, IP address, account name, and password. See ”Adding a fabric” on page 40. • Select Start Application Without Specifying a Fabric to open the McDATA Web Server window shown in Figure 2. Click Add to open the Add a New Fabric dialog, which prompts you for a fabric name, IP address, account name, and password.
Exiting McDATA Web Server or McDATA Element Manager Select File > Exit to exit the application session. Enter the password and click OK, if the fabric view file was saved with a password. Setting preferences You can customize the following preference settings for McDATA Web Server and McDATA Element Manager: • Change the location of the working directory in which to save files. • Change the location of the browser used to view the online help.
Using online help Online help is available for the McDATA Web Server and McDATA Element Manager applications and their functions. To open online help, choose one of the following: • Select Help > Help Topics. • Click Help in the tool bar. • Click Help in dialogs to display context-sensitive help in dialogs. Viewing software version and copyright information Select Help > View to view software version and copyright information.
User interface The McDATA Web Server and McDATA Element Manager applications share a common interface. The McDATA Web Server uses two basic displays to manage the fabric and individual switches: the topology display and the faceplate display as shown in Figure 5. The topology display shows all switches that are able to communicate and all connections between switches. The faceplate display shows the front of a single switch and its ports.
Menu bars The menus and the options vary depending on the management application and the display. For example, the Port menu and many of the Switch menu selections are available only in the faceplate display. McDATA Web Server topology display menu The McDATA Web Server topology display menu options are shown in Figure 6. Figure 6 McDATA Web Server Topology display menu McDATA Web Server faceplate display menu The McDATA Web Server faceplate menu options are shown in Figure 7.
McDATA Element Manager faceplate display menu The McDATA Element Manager faceplate menu options are shown in Figure 8. These menus differ from the McDATA Web Server faceplate menus in the following ways: • There is no Fabric menu • The Zoning Menu is limited to the Edit Zoning Config... option • The Show Event Browser option is added to the View menu. • There is no Security menu.
McDATA Web Server Tool bar The McDATA Web Server tool bar consists of a row of graphical buttons that you can use to access functions as shown in Table 3. The tool bar buttons are an alternative method to using the menu bar. The tool bar can be relocated in the display by clicking and dragging the handle at the left edge of the tool bar.
McDATA Web Server fabric tree The McDATA Web Server fabric tree lists the managed fabrics and their switches as shown in Figure 9. The window width can be adjusted by clicking and dragging the moveable window border. An entry handle located to the left of an entry in the tree indicates that the entry can be expanded or collapsed. Click this handle or double-click the entry to expand or collapse a fabric tree entry. A fabric entry expands to show its member switches.
Working status Indicator The working status indicator, located in the lower right corner of the McDATA Web Server window, shows when the management workstation is exchanging information with the fabric. As conditions change, the fabric forwards this information to the management workstation where it is reflected in the various displays.
Working with switches and links Switch and link icons are selectable and moveable, and serve as access points for other displays and menus. You select switches and links to display information about them, modify their configuration, or delete them from the display. Context-sensitive popup menus are displayed when you right-click on a switch or link icon, or in the background of the topology display graphic window. Selecting switches and links Selected switch icons are highlighted in light blue.
Using the faceplate display The McDATA Web Server and McDATA Element Manager faceplate displays, shown in Figure 11, display the switch name and operational state, and port status. The external ports are numbered 0 and 9. Internal ports are numbered 1–8. The port numbers 1–8 correspond to server blades slots 1–8.
Port views and status Port color and text provide information about the port and its operational state. Green indicates active; gray indicates inactive. The faceplate display provides the following views of port status corresponding to the View menu options in the faceplate display. See ”Monitoring port status” on page 98 for more information about these displays.
Faceplate data windows The faceplate display provides the following data windows corresponding to the data window tabs: • Devices—Displays information about devices (hosts and storage targets) connected to the switch. • Switch—Displays current switch configuration data. • Port Statistics—Displays performance data for the selected ports. • Port Information—Displays information for the selected ports.
Using McDATA Web Server/McDATA Element Manager
2 Managing fabrics This section describes the following tasks that manage fabrics using McDATA Web Server: • Securing a fabric, page 29 • Tracking fabric firmware and software versions, page 39 • Managing the fabric database, page 40 • Displaying fabric information, page 44 • Working with device information and nicknames, page 50 • Zoning a fabric, page 52 Securing a fabric Fabric security consists of the following: • Security consistency checklist, page 29 • Connection security, page 29 • User account se
User account security User account security is the process by which your user account and password are authenticated with the list of valid user accounts and passwords. The switch validates your account and password when you attempt to add a fabric using McDATA Web Server or log in to a switch through Telnet. Your system administrator defines accounts, passwords, and authority levels that are stored on the switch. See ”Managing user accounts” on page 61 for more information.
In addition to authorization, the switch can be configured to require authentication to validate the identity of the connecting switch, device, or host. Authentication can be performed locally using the switch security database, or remotely using a RADIUS server. With a RADIUS server, the security database for the entire fabric resides on the server. In this way, the security database can be managed centrally, rather than on each switch. You can configure up to five RADIUS servers to provide failover.
The orphan security set contains the security groups and members that don't belong to a user-defined security set. Excluding the orphan security set, you can only have 1 group type in a security set. The three types of security groups are: • ISL—Default (E_Port authentication) • MS (Management Server CT authentication) • Port (F_Port authentication) Figure 12 Edit Security dialog Use the File menu in the Edit Security dialog to: • Edit the security configuration on the switch.
Create Security Set dialog Use the Create Security Set dialog shown in Figure 13 to create a new security set. There is a maximum of 4 security sets. Figure 13 Create Security Set dialog To add a security set from the faceplate display, perform the following procedure: 1. Click Security on the tool bar, or select Security > Edit Security to open the Edit Security dialog. 2. To open the Create a Security Set dialog, choose one of the following: • Click Security Set in the Edit Security dialog tool bar.
The naming conventions for all security groups are listed below. • Must start with a letter. • All alphanumeric chars [aA—zZ] [0—9]. • The symbols $_ - and ^ are the only symbols allowed. An empty (no members) security group in the active security set will prevent all connections for that security group type. For example, an empty ISL security group will cause the switch to refuse all logins from other switches. To add a security group to a security set, perform the following procedure: 1.
The conventions for Port security group members are listed below: • You can enter member World Wide Name (WWN), which must be 16 hex characters, or 23 characters with valid WWN format xx:xx:xx:xx:xx:xx:xx:xx. • The authentication choices are None and CHAP. • The Secret field is disabled if authentication is set to None. If authentication is CHAP, the Secret field is enabled. • Generate is only enabled when authentication is set to CHAP.
Editing the security configuration on a switch To edit a security configuration on the switch from the faceplate display, perform the following procedure: 1. Choose one of the following to open the Edit Security dialog: • Click Security on the tool bar. • Select Security > Edit Security. By default, the security configuration on the switch is displayed in the Edit Security dialog. 2. Choose one of the following from the Edit Security dialog: • Select File > Open File.
Security Config dialog Use the Security Config dialog, shown in Figure 16, to save the active security configuration on the switch to non-volatile or to temporary memory, and to require the domain ID of a switch be validated before attaching to the fabric. Figure 16 Security Config dialog To configure switch security from the faceplate display, perform the following procedure: 1. Select Security > Edit Security Config to open the Security Config dialog. 2.
Deactivating a security set Only one security set can be active at one time. To deactivate an active security set from the faceplate display, perform the following procedure: 1. Select Security > Deactivate Security Set. 2. Select a security set from the drop-down list in the Deactivate Security Set dialog. 3. Click Yes to confirm that you want to deactivate the active security set in the Deactivate Security Set dialog.
Tracking fabric firmware and software versions The Fabric Tracker option enables you to generate a snapshot or baseline of current system version information, which can be viewed, analyzed and compared to other snapshot files, and exported to a file. Information includes date and time, McDATA Web Server version, switch active firmware version, device hardware, drivers, and firmware version from FDMI. Select Fabric > Fabric Tracker to open the Fabric Snapshot Analysis dialog shown in Figure 17.
Managing the fabric database A fabric database contains the set of fabrics that you have added during a McDATA Web Server session. Initially, if you do not open an existing fabric or fabric view file, the McDATA Web Server application opens with an empty fabric database. Adding a fabric To add a fabric to the database, perform the following procedure: 1. Select Fabric > Add Fabric to open the Add a New Fabric dialog shown in Figure 18. Figure 18 Add a New Fabric dialog 2.
Opening a fabric view file A fabric view file is one or more fabrics saved to a file. To open an existing view file, perform the following procedure: 1. Choose one of the following: • Select Fabric > Add Fabric • Click Add on the tool bar. 2. Enter a fabric name (optional) and the IP address of the switch through which to manage the fabric. 3. Enter an account (login) name and password. The factory account name and password are "admin" and "password".
Adding a new switch to a fabric If there are no special conditions to be configured for the new switch, simply plug in the switch and the switch becomes functional with the default fabric configuration. The default fabric configuration settings are: • Fabric zoning is sent to the switch from the fabric. • External ports are 1-Gbps/2-Gbps/4-Gbps ports and are GL_Ports. Internal ports are 2-Gbps ports and are FL_Ports. • The default static IP address of 10.0.0.1 and gateway of 10.0.0.
Replacing a failed switch The archive/restore works for all switches. However, the Restore menu item is not available for the in-band switches. You can only restore a switch out-of-band (the fabric management switch). There are certain parameters that are not archived, and these are not restored by McDATA Web Server. See ”Archiving a switch” on page 88 and ”Restoring a switch” on page 89 for information about archive and restore.
Displaying fabric information The topology display is your primary tool for monitoring a fabric. The graphic window of the topology display provides status information for switches, inter-switch links, and the Ethernet connection to the management workstation. The data window tabs show device, switch, link, and active zone set information. The Active Zoneset data window shows the zone definitions for the active zone set.
Displaying the Event Browser The Event Browser displays a list of events generated by the switches in the fabric and the switch management application. Events that are generated by the application are not saved on the switch, but can be saved to a file during the switch management session. To display the Event Browser in McDATA Web Server, choose one of the following: • Select Fabric > Show Event Browser. • Click Events on the tool bar.
Severity is indicated in the severity column using icons as described in Table 5. Table 5 Severity levels Severity icon Description Alarm—An alarm is a "serviceable event". This means that attention by the user or field service is required. Alarms are posted asynchronously to the screen and cannot be turned off. If the alarm denotes that a system error has occurred the customer and/or field representative will generally be directed to provide a "show support" capture of the switch.
Filtering the Event Browser Filtering the Event Browser enables you to display only those events that are of interest based on the event severity, timestamp, source, type, and description. Select Filter > Filter Entries in the Events Browser window to open the Filter Events dialog shown in Figure 20. The Event Browser displays those events that meet all of the criteria in the Filter Events dialog.
Devices data window The Devices data window displays information about devices (hosts and storage targets) connected to the switch. Click the Devices data window tab, in either the topology or faceplate display, to display device information for all devices that are logged into the selected fabric. To narrow the display to devices that are logged into specific switches, select one or more switches in the fabric tree or the topology display. Table 6 describes the entries in the Devices data window.
Active Zone Set data window The Active Zoneset data window, shown in Figure 21, shows the zone membership for the active zone set that resides on the fabric management switch. The active zone set is the same on all switches in the fabric – you can confirm this by adding a fabric through another switch and comparing Active Zone Set displays. Click the Active Zoneset data window tab in the topology display (only) to open the Active Zoneset data window.
Working with device information and nicknames McDATA Web Server enables you to perform the following: • Displaying detailed device information, page 50 • Exporting device information to a file, page 50 • Managing device port nicknames, page 50 Displaying detailed device information In addition to the information that is available in the Devices data dialog, you can click (i) in the Details column to display more information as shown in Figure 22.
Creating a nickname To create a device port nickname, perform the following procedure: 1. Select File > Nicknames to open the Nicknames dialog. 2. Choose one of the following methods to enter a nickname. A nickname must start with a letter and can have up to 64 characters. Valid characters include alphanumeric characters [aA—zZ][0—9] and special symbols [$ _ - ^ ]. • Click on a device in the table. Select Edit > Create Nickname to open the Add Nickname dialog.
Zoning a fabric If HAFM is used to manage the fabric, it is recommended to use HAFM to manage the fabric zoning. If HAFM is not used and other McDATA switch models are in the fabric, it is recommended to use SANpilot or Embedded Web Server to manage the fabric zoning. If all switches in the fabric are McDATA 4Gb SAN switches, use McDATA Web Server to manage the fabric zoning.
Zoning database Each switch has its own zoning database. The zoning database is made up of the active zone set that has been created on the switch or received from other switches. The switch maintains two copies of the zoning database: one copy is maintained in temporary memory for editing purposes; the second copy is maintained in permanent memory. Zoning database edits are made on an individual switch basis and are not propagated to other switches in the fabric when saved.
Managing the zoning database Managing the zoning database consists of the following: • Editing the zoning database, page 54 • Configuring the zoning database, page 56 • Saving the zoning database to a file, page 56 • Restoring the zoning database from a file, page 56 • Restoring the default zoning database, page 57 • Removing all zoning definitions, page 57 Editing the zoning database Select Zoning > Edit Zoning from the faceplate display to open the Edit Zoning dialog shown in Figure 23.
You can select zone sets, zones, and ports in the following ways: • Click a zone, zone set, or port icon. • Right-click to select a zone set or zone, and open the corresponding popup menu. • Press and hold Shift while clicking several consecutive icons. • Press and hold Control while clicking several non-consecutive icons. Using tool bar buttons, popup menus, or a drag-and-drop method, you can create and manage zone sets and zones in the zoning database. Table 7 describes the zoning tool bar operations.
Configuring the zoning database Use the Zoning Config dialog to change the Interop Auto Save and Default Zone configuration parameters. The Default Zone parameter applies only when Interop Mode is set to McDATA Fabric Mode. Open the faceplate display. Select Zoning > Edit Zoning Config to open the Zoning Config dialog shown in Figure 24. Click OK after making changes to put the new values into effect.
Restoring the default zoning database Restoring the default zoning clears the switch of all zoning definitions. Restoring default zoning is a fabric-wide action. When you are in Standard mode and restore default zoning, no devices/ports are able to communicate with each other on the switches.
Activating and deactivating a zone set You must activate a zone set to apply its zoning definitions to the fabric. Only one zone set can be active at one time. When you activate a zone set, the switch distributes that zone set to the temporary zoning database on every McDATA 4Gb SAN Switch in the fabric. To activate a zone set, perform the following procedure: 1. Select Zoning > Activate Zone Set to open the Activate Zone Set dialog. 2. Select a zone set from the Select Zone Set drop-down list. 3.
Creating a zone in a zone set To create a zone in a zone set, perform the following procedure: 1. Select Zoning > Edit Zoning to open the Edit Zoning dialog. 2. Select a zone set in which to create a zone. 3. Select Edit > Create a Zone. 4. Enter a name for the new zone in the Create a Zone dialog The new zone name is displayed in the Zone Sets dialog. A zone name must begin with a letter and be no longer than 64 characters. Valid characters are 0—9, A—Z, a—z, _, ^, $, and -. 5. Click OK.
Renaming a zone or a zone set To rename a zone, perform the following procedure: 1. Click the zone/zone set to be renamed in the Zone Sets tree of the Edit Zoning dialog. 2. Select Edit > Rename. 3. Enter a new name for the zone/zone set in the Rename Zone/Rename Zone Set dialog. 4. Click OK to save changes. Removing a zone member Removing a zone member will affect every zone and zone set in which that zone is a member. To remove a member from a zone, perform the following procedure: 1.
3 Managing switches This section describes the following tasks that manage switches using the McDATA Web Server or McDATA Element Manager application.
Creating user accounts A switch can have a maximum of 15 user accounts. To create a new user account on a switch, perform the following procedure: 1. Select Switch > User Accounts in the faceplate display to open the User Account Administration dialog. 2. Click the Add Account tab to open the Add Account tab page shown in Figure 25. 3. Enter an account name in the New Account Login field. Account names are limited to 15 characters. 4.
Removing a user account To remove a user account on a switch, perform the following procedure: 1. Select Switch > User Accounts in the faceplate display to open the User Account Administration dialog. 2. Click the Remove Account tab to open the Remove Account tab page shown in Figure 26. 3. Select the account (login) name from the list of accounts at the top of the dialog. 4. Click Remove Account. 5. Click Close to close the User Account Administration dialog.
Changing a user account password Any user can change their password for their account, but only the Admin account name can change the password for another user’s account. If the administrator does not know the user’s original password, the administrator must remove the account and add the account. To change the password for an account on a switch, perform the following procedure: 1. Select Switch > User Accounts in the faceplate display to open the User Account Administration dialog. 2.
Modifying a user account To modify a user account on a switch, perform the following procedure: 1. Select Switch > User Accounts in the faceplate display to open the User Account Administration dialog. 2. Click the Modify Account tab to open the Modify Account tab page shown in Figure 28. 3. Select the account (login) name from the list of accounts at the top of the dialog. 4. Select the Admin Authority Enabled option to grant admin authority to the account name. 5. Select an Account Expiration Date option.
Configuring RADIUS servers A RADIUS server authenticates users and devices using a challenge/response protocol over a secure SSL connection. Basic implementations consist of a central RADIUS server containing a database of authorized users as well as authentication information. A RADIUS client wishing to verify the authenticity of a user issues a challenge to the user and collects the response to the challenge.
5. Enter the remote UDP port number of the Authentication RADIUS Server in the UDP Port field. The RADIUS Accounting Server UDP port will always be the value of Device/User Authentication Server UDP Port + 1. When enabled, the RADIUS Accounting Server audits user activity whether UserAuthServer is enabled or not. The RADIUS Accounting Server default is False. 6. Enter the timeout value in seconds (minimum of 1 second, maximum of 30 seconds) in the Timeout field.
Editing RADIUS server information Editing information of a RADIUS server involves changing the configuration of a RADIUS server. Figure 31 RADIUS Server Information dialog—Edit Server tab page To edit information of a RADIUS server, perform the following procedure: 1. Select Switch > Radius Servers in the faceplate display. 2. Click the Edit Server tab in the Radius Server Information dialog shown in Figure 31. 3. Select the server to be edited in server list at the top of the dialog. 4.
Modifying RADIUS server authentication order Editing information of a RADIUS server involves changing the configuration of a RADIUS server. Figure 32 RADIUS Server Information dialog—Modify Authentication Order tab page To modify the authentication order information of a RADIUS server, perform the following procedure: 1. Select Switch > Radius Servers in the faceplate display. 2. Click the Modify Authentication Order tab in the Radius Server Information dialog shown in Figure 32. 3.
Displaying switch information The faceplate display and data windows provide the following switch information: • Switch event log • Device and HBA information • Switch specifications and addresses • Configuration parameters • Port performance statistics • Port information • Configured zone sets (McDATA Web Server only) Figure 33 shows the McDATA Web Server faceplate display for the McDATA 4Gb SAN Switch.
Switch data window The Switch data window displays current network and switch information for the selected switches. See ”Configuring a switch” on page 78 for more information about the Switch data window. Table 9 describes the Switch data window entries. To open the Switch data window, choose one of the following: • Select one or more switches in the topology display. Click the Switch data window tab. • Open the faceplate display. Click the Switch data window tab.
Table 9 72 Switch data window entries (continued) Entry Description Interop Mode Interoperability mode. Use Standard to connect to FC-SW-2 compliant switches and McDATA switches in Open Fabric Mode. Use McDATA Fabric Mode to connect to McDATA switches in McDATA Fabric Mode. The default is Standard. Legacy Address Format Not applicable Interop Auto Save Zoning auto save status. Saves zoning updates in temporary memory and the zoning database (True), or only in temporary memory (False).
Table 9 Switch data window entries (continued) Entry Description FDMI HBA Entry Limit Maximum number of HBAs that can be registered with a switch. FDMI Enable Fabric Device Management Interface status. If enabled, device information can be obtained, managed, and saved through the fabric using Name Service Management Server functions. The switch data window reports any and all FDMI information reported by the entry switch, if FDMI is enabled on the entry switch.
Port Statistics data window The Port Statistics data window displays port performance data for the selected ports. Click the Port Stats data window tab in the faceplate display to open the Port Statistics data window. See ”Port Statistics data window” on page 100 for a description of the Port Statistics data window entries. The Statistics drop-down list is available on the Port Statistics data window, and provides different ways to view detailed port information.
Configuring port threshold alarms You can configure the switch to generate alarms for selected events. Configuring an alarm involves choosing an event type, rising and falling triggers, a sample window, and finally enabling or disabling the alarm. To configure port threshold alarms, perform the following procedure: 1. Open the faceplate display. 2. Select Switch > Port Threshold Alarm Configuration.
NOTE: The switch will down a port if a rising trigger alarm is not cleared after three consecutive sample windows. Generate rising trigger alarm; eligibility ends Generate rising trigger alarm; eligibility ends Rising trigger Event count Generate falling trigger alarm; eligibility is reset Falling trigger Sample window Figure 36 Port threshold alarm example 8. Enter a sample window in seconds. The sample window defines the period of time in which to count events. 9.
Resetting a switch Resetting a switch reboots the switch using the switch configuration parameters last saved in permanent memory on the switch. Depending on the reset type, a switch reset may or may not include a Power On Self Test (POST) or it may or may not disrupt traffic. Table 9 describes the types of switch resets. During a hotreset operation, fabric services will be unavailable for a short period (30—75 seconds depending on switch model).
Configuring a switch Switch configuration is divided into three areas: chassis configuration, network configuration, and SNMP configuration. Chassis configuration specifies switch-wide FC settings. Network configuration specifies IP settings, remote logging, and the NTP client. SNMP configuration specifies SNMP settings and traps. You can configure a switch explicitly or you can use the Configuration Wizard.
Switch administrative states The switch administrative state determines the operational state of the switch. The switch administrative state exists in two forms: the configured administrative state and the current administrative state. • The configured administrative state is the state that is saved in the switch configuration and is preserved across switch resets. McDATA Web Server or McDATA Element Manager always makes changes to the configured administrative state.
In McDATA Fabric mode, the McDATA 4Gb SAN Switch will display the domain IDs the same as other M-series directors and edge switches no matter which management utility is used. The valid domain ID range is 1—31 for McDATA Fabric mode. Prior to changing from McDATA Fabric mode to Standard mode, it is recommended that the switch be isolated from the fabric (take switch offline) before making the configuration changes and all domain IDs in the fabric should be noted to avoid conflicts.
Fabric Device Management Interface Fabric Device Management Interface (FDMI) provides a means to gather and display device information from the fabric, and allows FDMI capable devices to register certain information with the fabric, if FDMI is enabled. McDATA Web Server or McDATA Element Manager will report any and all FDMI information reported by the entry switch, if FDMI is enabled on the entry switch.
Advanced switch properties The Advanced Switch Properties dialog enables you to set the timeout values and interop mode settings. The Advanced Switch Properties dialog is available for only the entry switch, because an in-band switch can not be taken offline. The switch will automatically be taken offline temporarily and will be restored to its original state after the changes are completed. Select Switch > Advanced Switch Properties to open the Advanced Switch Properties dialog.
Configuring system services The System Services dialog provides a central location for you to enable or disable any of the external user services such as SNMP, Secure Sockets Layer (SSL), Secure SHell (SSH), embedded switch management application (McDATA Web Server or McDATA Element Manager), CLI, Network Time Protocol (NTP), and Common Information Model (CIM). Select Switch > Services to display the System Services dialog.
• CIM—Common Information Model. Allows management of the switch through third-party applications that use CIM. • FTP—File Transfer Protocol. Allows file transfers to the switch via FTP. FTP is required for out-of-band firmware uploads which will complete faster than in-band firmware uploads. • Management Server—Allows management of the switch through third-party applications that use GS-3 Management Server.
IP configuration The IP configuration identifies the switch on the Ethernet network and determines which network discovery method to use. Table 14 describes the IP configuration parameters.
SNMP properties Use the SNMP Properties dialog shown in Figure 41 to change SNMP configuration parameters. You must select a switch in the topology display or open the faceplate display to open the SNMP Properties dialog. Select Switch > SNMP Properties. Making any changes. Click OK to put the new values into effect. NOTE: Since read community, trap community, and write community settings are like passwords and are write-only fields, the current settings are displayed as asterisks.
SNMP configuration The SNMP configuration defines how authentication traps are managed. Table 15 describes the SNMP configuration parameters. The illegal characters for the user-defined fields are the pound sign (#), semi-colon (;), and comma (,).
SNMP trap configuration The SNMP trap configuration defines how traps are set. Choose from the tabs Trap1 – Trap 5 to configure each trap. Table 16 describes the SNMP configuration parameters. Table 16 SNMP trap configuration parameters Parameter Description Trap Version Specifies the SNMP version (1 or 2) with which to format traps Trap 1 Enabled Trap Address 1 Enables or disables the trap. If disabled, traps are not configurable. Specifies the IP address to which SNMP traps are sent.
Restoring a switch Restoring a switch loads the archived switch configuration parameters to the switch. The switch configuration must be archived before it can be restored. The switch archive must be compatible with the switch to be restored; that is, you can restore a McDATA 4Gb SAN Switch only with an archive from a McDATA 4Gb SAN Switch. See ”Archiving a switch” on page 88 for more information. NOTE: The switch being restored should be physically disconnected from the fabric.
• Configured Security—Restores all security sets in the switch database. See ”Device security” on page 30 for more information. • Radius Server—Restores all RADIUS Server information defined in the switch database. See ”Configuring RADIUS servers” on page 66 for more information. 7. If you select the Configured Zoning or Full Restore option and the file contains zone sets, a dialog prompts you to activate one of those zone sets. Click Yes.
Table 17 Factory default configuration settings (continued) Setting Value Location Undefined Trap Enabled False Trap Port 162 Trap Address Trap 1: 10.0.0.254; Traps 2-5: 0.0.0.
3. Select Switch > Features to display the Feature Licenses dialog shown in Figure 43. Figure 43 Features Licenses dialog 4. Click Add to open the Add License Key dialog shown in Figure 44. Figure 44 Add License Key dialog 5. Enter the license key in the Key field. 6. Click Get Description to display the PFE key description. 7. Click Add Key. Allow a minute or two to complete. Installing firmware The switch comes with current firmware installed.
Using McDATA Web Server or McDATA Element Manager to install firmware Installing firmware involves loading, unpacking, and activating the firmware image on the switch. McDATA Web Server or McDATA Element Manager does this in one operation. To provide consistent performance throughout the fabric, ensure that all McDATA 4Gb SAN Switch for HP p-Class BladeSystem switches are running the same version of firmware.
Using the CLI to install firmware To install firmware using the CLI when a File Transfer Protocol (FTP) server is present on the management workstation, use the Firmware Install command. See the ”Firmware Install command” on page 128 for more information. This command is disruptive to the fabric traffic. 1. Enter the following command to download the firmware from a remote host to the switch, install the firmware, then reset the switch to activate the firmware.
Displaying hardware status To display a summary of the hardware status information in a popup text box, rest the cursor over the chassis LED cluster in the faceplate display. • Power LED—Indicates the voltage status of the switch. • Heartbeat LED—Indicates the general status of the internal switch processor and the results of the POST. • System Fault LED—Indicates an error, such as an over temperature condition, internal system error, voltage fault, or corrupt configuration.
Managing switches
4 Managing ports This section describes the following topics about managing ports and devices using McDATA Web Server or McDATA Element Manager: • Displaying port information, page 97 • Configuring ports, page 104 • Resetting a port, page 106 • Testing ports, page 106 Displaying port information Port information is available primarily in the faceplate display shown in Figure 46. The faceplate display data windows provide information and statistics for switches and ports.
Monitoring port status The faceplate display provides the following port related information: • Port type • Port operational state • Port speed • Port media To display port number and status information for a port, position the cursor over a port on the faceplate display. The status information changes depending on the View menu option selected. Displaying port types To display port type status, from the faceplate display, select View > View Port Types.
Displaying port speeds To display the speed of each port in the faceplate display, select View > View Port Speeds. Table 20 lists the possible port speeds. Table 20 Port speeds State Description Au Auto-detect 1Gb 1-Gbps transmission speed 2Gb 2-Gbps transmission speed 4Gb 4-Gbps transmission speed Displaying transceiver media status To display transceiver media status, select View > View Port Media. Table 21 lists the port media states and their meanings. Table 21 .
Port Statistics data window The Port Statistics data window displays statistics about port performance. Select one or more ports in the faceplate display that you want to view statistics. Click the Port Stats data window tab to open the Port Statistics window. Table 22 describes the Port Statistics data window entries. The Statistics drop-down list is available on the Port Statistics data window, and provides different ways to view detailed port information. Click the down arrow to open the drop-down list.
Table 22 Port Statistics data window entries (continued) Entry Description Flow Errors Number of times a frame is received and all the switch ports receive buffers are full. The normal Fabric Login exchange of flow control credit should prevent this from occurring. The frame will be discarded. FReject Number of frames, from devices, that have been rejected. Frames can be rejected for any of a large number of reasons.
Table 22 Port Statistics data window entries (continued) Entry Description Total Rx Frames Total number of frames received by the port Total Rx Words Total number of words received by the port Total Tx Frames Total number of frames transmitted by the port Total Tx Words Total number of words transmitted by the port Tx Link Resets Number of link reset primitives sent from this port to an attached port Total Offline Sequences Total number of offline sequences transmitted and received by the port
Table 23 Port Information data window entries (continued) Entry Description MFS Mode Multiple Frame Sequence bundling status I/O Stream Guard Not applicable Administrative Port Speed The speed requested by the user Operational Port Speed The speed actually being used by the port Device Scan Device scan status. Enabled means the switch queries the connected device during login for FC-4 descriptor information.
Configuring ports The port settings or characteristics are configured using the Port Properties dialogs shown in Figure 47. Select a port in the faceplate display. Select Port > Port Properties to open the Port Properties dialog. The Port Properties dialog shows the switch name and the selected ports.
Changing port speeds The 1-Gbps/2-Gbps/4-Gbps ports are capable of transmitting and receiving at 1-Gbps, 2-Gbps, or 4-Gbps. The ports can be configured for either transmission speed or to sense the transmission speed of the device to which it is connected. Table 25 describes the port speeds. To change the port speed, perform the following procedure: 1. Select one or more 1-Gbps/2-Gbps/4-Gbps ports in the faceplate display. 2. Select Port > Port Properties. 3.
Changing port symbolic name To change the symbolic name of a port from the faceplate display, perform the following procedure: 1. Open the faceplate display and select a port. 2. Select Port > Port Symbolic Name. 3. In the Port Symbolic Name dialog, choose one of the following: • Enter a new name for the port in the Set Port Symbolic Name field. The symbolic name can have up to 32 characters. • Select the Restore Default Port Symbolic Name option to restore the default name. 4. Click OK.
• Node-to-Node (online)—The Node-to-Node test verifies communications between the port and its device node or device loop. The port being tested must be online and connected to a remote device. The port passes the test if the frame that was sent by the ASIC matches the frame that was received. This test does not disrupt communication on the selected port. This test requires that the port be online, and therefore, does not disrupt communication.
Managing ports
5 Command Line Interface The CLI enables you to perform a variety of fabric and switch management tasks through an Ethernet connection.
Working with switch configurations Successful management of switches and fabrics with the CLI depends on the effective use of switch configurations. Modifying configurations, backing up configurations, and restoring configurations are key switch management tasks. Modifying a configuration A switch supports up to 10 configurations including the default configuration. Each switch configuration contains switch, port, port threshold alarm, and zoning configuration components.
Backing up and restoring switch configurations Backing up and restoring a configuration is useful to protect your work or for use as a template in configuring other switches. The Config Backup command creates a file on the switch, named configdata. This file can be used to restore a switch configuration only from the CLI; it cannot be used to restore a switch using McDATA Web Server or McDATA Element Manager.
Commands The command syntax is as follows: command operand operand [value] operand [value1] [value2] The command is followed by one or more operands. Consider the following rules and conventions: • Commands and operand are case insensitive. • Required operand values appear in standard font: [value]. Optional values are shown in italics: [value]. • Underlined portions of the operand in the command format indicate the abbreviated form that can be used. For example the Delete operand can be abbreviated Del.
Table 28 Commands listed by authority level Monitoring commands Configuration command Help (135) Admin History (136) Admin session commands Ping (143) CIM1 (115) Ps (144) CIMListener (116) Quit (145) CIMSubscription (118) Show (180) Config1 (120) Show Config (190) Create (123) Show Log (193) Date1 (126) Show Perf (196) Feature (127) Show Setup (198) Firmware Install (128) Uptime (204) Group1 (129) Whoami (207) Hardreset (134) Hotreset (137) Image (138) L
Admin command Description Starts and ends an Admin session. The Admin session allows commands that change the fabric and switch configurations. Only one Admin session can be started on the switch at any time. An idle Admin session will time out after a period of time (the default is 30 minutes) which can be changed using the Set Setup System command. Authority Admin Syntax admin start (or begin) end (or stop) cancel Operands start or begin Opens the Admin session.
CIM command Description Manages CIM listener and subscription configurations on the switch. Authority Admin session Syntax cim cancel clear edit limits save Operands cancel Terminates the current CIM edit session without saving changes that were made. clear Clears all CIM listener and subscription configurations from the switch. edit Opens a CIM edit session. limits Displays the maximum allowed number of CIM listeners, subscriptions, and subscriptions per listener.
CIMListener command Description Configures CIM indication service listeners and adds subscriptions to listeners. See the CIMSubscription command for information about configuring subscriptions. Authority Admin session and a CIM Edit session. See the CIM command for information about opening a CIM edit session.
Examples The following is an example of the CIMListener Create command: McDATA4GbSAN (admin-cim) #> cimlistener create listener_1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so. Name Type URL listener_1 (2=Permanent, 3=Transient) (IP address:port format) [Permanent ] [10.0.0.
CIMSubscription command Description Creates, edits, or removes CIM subscriptions. Authority Admin session and a CIM Edit session. Syntax cimsubscription create [subscription_name] delete [subscription_name] edit [subscription_name] Operands create [subscription_name] Prompts you in a line-by-line fashion to create a CIM subscription with the name given by [subscription_name]. [subscription_name] can have up to 32 characters: 0—9, A—Z, a—z, _, $, ^, and -.
Examples The following is an example of the CIMSubscription Create command: McDATA4GbSAN (admin-cim) #> cimsubscription create subscription_1 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
Config command Description Manages the FC configurations on a switch. For information about setting the port and switch configurations, see the Set Config command. Authority Admin session for all operands except List. Syntax config activate [config_name] backup cancel copy [config_source] [config_destination] delete [config_name] edit [config_name] list restore save [config_name] Operands activate [config_name] Activates the configuration given by [config_name].
restore Restores configuration settings to an out-of-band switch from a backup file named configdata, which must be first uploaded on the switch using FTP. You create the backup file using the Config Backup command. Use FTP to load the backup file on a switch, then enter the Config Restore command. After the restore is complete, the switch automatically resets. See ”Backing up and restoring switch configurations” on page 111. NOTE: All management sessions are terminated because the switch is reset.
The following is an example of how to upload a configuration backup file (configdata) from the workstation to the switch, and then restore the configuration. #> ftp symbolic_name or ip_address user: images password: images ftp> bin ftp> put configdata ftp> quit McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> config restore The switch will be reset after restoring the configuration. Please confirm (y/n): [n] y Alarm Msg: [day month date time year][A1005.
Create command Description Creates support files for troubleshooting switch problems, and certificates for secure communications for McDATA Web Server and McDATA Element Manager. Authority Admin session Syntax create certificate support Operands certificate Creates a security certificate on the switch. The security certificate is required to establish an SSL connection with a management application such as McDATA Web Server.
Examples The following is an example of the Create Support command when an FTP server is available on the workstation: McDATA4GbSAN (admin) #> create support Log Msg:[Creating the support file - this will take several seconds] FTP the dump support file to another machine? (y/n): y Enter IP Address of remote computer: 10.20.33.130 Login name: johndoe Enter remote directory name: bin/support Would you like to continue downloading support file? (y/n) [n]: y Connected to 10.20.33.130 (10.20.33.130).
See also Date command, page 126 Set command, page 156 Set Setup command, page 172 McDATA® 4Gb SAN Switch for HP p-Class BladeSystem user guide 125
Date command Description This command displays or sets the system date and time. To set the date and time the information string must be provided in this format: MMDDhhmmCCYY. The new date and time takes effect immediately. Authority Admin session except to display the date. Syntax date [MMDDhhmmCCYY] Operands [MMDDhhmmCCYY] Specifies the date – this requires an Admin session. If you omit [MMDDhhmmCCYY], the current date is displayed which does not require an Admin session.
Feature command Description Adds Product Feature Enablement (PFE) key features to the switch and displays the PFE key log. A Product Feature Enablement (PFE) key is a password that you can purchase from your switch distributor or authorized reseller to enable particular features in your switch. To obtain the McDATA 4Gb SAN Switch serial number and Product Feature Enablement license key, follow the step-by-step instructions on the "firmware feature entitlement request certificate" for the PFE key.
Firmware Install command Description Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch (without a POST) to activate the firmware.
Group command Description Creates groups, manages membership within the group, and manages the membership of groups in security sets. IMPORTANT: This command is available only with the SANtegrity Enhanced PFE key. Authority Admin session and a Security Edit session. See the Security command for information about starting a Security Edit session. The List, Members, Securitysets, and Type operands are available without an Admin session.
Table 31 ISL Group member attributes (continued) Attribute Description Secondary Hash Hash function to use to decipher the encrypted Secondary Secret sent by the ISL group member. Hash values are MD5 or SHA-1. The Secondary Hash is used when the Primary Hash is not available on the ISL group member. The Primary Hash and the Secondary Hash cannot be the same. Secondary Secret Hex string that is encrypted by the Secondary Hash and sent for authentication.
copy [group_source] [group_destination] Creates a new group named [group_destination] and copies the membership into it from the group given by [group_source]. create [group] [type] Creates a group with the name given by [group] with the type given by [type]. A group name must begin with a letter and be no longer than 64 characters. Valid characters are 0—9, A—Z, a—z, _, $, ^, and -. The security database supports a maximum of 16 groups. If you omit [type], ISL is used.
Table 34 Group member attributes (continued) Attribute Description Secret Hexadecimal string that is encrypted by the Hash function for authentication with MS group members. The string has the following lengths depending on the Hash function: (MS Groups) MD5 hash: 16-byte SHA-1 hash: 20-byte Binding (ISL Groups) Domain ID of the switch to which to bind the ISL group member World Wide Name. This option is available only if FabricBindingEnabled is set to True using the Set Config Security command.
The following is an example of the Group Edit command: McDATA4GbSAN (admin-security) #> group edit G1 10:00:00:c0:dd:00:90:a3 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
Hardreset command Description Resets the switch and performs a POST. This reset disrupts traffic, activates the pending firmware, and clears the alarm log. To save the alarm log before resetting, see the Set Log command. Authority Admin session Syntax hardreset Notes To reset the switch without a POST, see the Reset command. To reset the switch without disrupting traffic, see the Hotreset command.
Help command Description Displays a brief description of the specified command, its operands, and usage. Authority None Syntax help [command] [operand] Operands [command] Displays a summary of the command given by [command] and its operands. If you omit [command], the system displays all available commands. [operand] Displays a summary of the operand given by [operand] belonging to the command given by [command]. If you omit [operand], the system displays the available operands for the specified command.
History command Description Displays a numbered list of the previously entered commands from which you can re-execute selected commands. Authority None Syntax history Notes Use the History command to provide context for the ! command: • Enter ![command_string] to re-execute the most recent command that matches [command_string]. • Enter ![line number] to re-execute the corresponding command from the History display • Enter ![partial command string] to re-execute a command that matches the command string.
Hotreset command Description Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This command terminates all management sessions, saves all configuration information, and clears the event log. After the pending firmware is activated, the configuration is recovered. This process takes less than 80 seconds. To save the event log to a file before resetting, see the Set Log command.
Image command Description Manages and installs switch firmware. Authority Admin session Syntax image cleanup fetch [account_name] [ip_address] [file_source] [file_destination] install list unpack [file] Operands cleanup Removes all firmware image files from the switch. All firmware image files are removed automatically each time the switch is reset.
Notes To provide consistent performance throughout the fabric, ensure that all switches are running the same version of firmware. To install firmware when the management workstation has an FTP server, use the Image Install command or the Firmware Install command. To install firmware when the management workstation does not have an FTP server, perform the following procedure: 1. Connect to the switch through the Ethernet port. 2.
Examples The following is an example of the Image Install command: McDATA4GbSAN (admin) #> image install Warning: Installing new firmware requires a switch reset. Continuing with this action will terminate all management sessions, including any Telnet sessions. When the firmware activation is complete, you may log in to the switch again. Do you want to continue? [y/n]: y Press 'q' and the ENTER key to abort this command. User Account : johndoe IP Address : 10.20.33.130 Source Filename : 5.2.00.
Lip command Description Re-initializes the specified loop port. Authority Admin session Syntax lip [port_number] Operands [port_number] The number of the port to be re-initialized.
Passwd command Description Changes a user account’s password. Authority Admin account name and an Admin session to change another account’s password. You can change you own password without an Admin session. Syntax passwd [account_name] Operands [account_name] The user account name. To change the password for an account name other than your own, you must open an Admin session with the account name Admin. If you omit [account_name], you will be prompted to change the password for the current account name.
Ping command Description Initiates an attempt to communicate with another switch over an Ethernet network and reports the result. Authority None Syntax ping [ip_address] Operands [ip_address] The IP address of the switch to query. Broadcast IP addresses, such as 255.255.255.255, are not valid. Examples The following is an example of a successful Ping command: McDATA4GbSAN #> ping 10.20.11.57 Ping command issued. Waiting for response... McDATA4GbSAN #> Response successfully received from 10.20.11.57.
Ps command Description Displays current system process information. Authority None Syntax ps Examples The following is an example of the Ps command: McDATA4GbSAN #> ps PID 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 404 405 406 PPID %CPU TIME 327 0.0 00:00:00 327 0.0 00:00:01 327 0.0 00:00:21 327 0.1 00:05:35 327 0.2 00:11:29 327 0.0 00:00:04 327 0.0 00:02:16 327 0.0 00:02:44 327 0.8 00:35:12 327 0.0 00:00:29 327 0.0 00:02:46 327 0.0 00:00:21 327 5.6 04:08:24 327 0.0 00:01:38 327 0.
Quit command Description Closes the Telnet session. Authority None Syntax quit, exit, or logout Notes You can also press Control+D to close the Telnet session.
Reset command Description Resets the switch configuration parameters. If you omit the operand, the default is Reset Switch. Authority Admin session Syntax reset cim config [config_name] factory port [port_number] radius security services snmp switch (default) system zoning Operands cim Resets cim configuration to default values.
system Resets the system configuration settings to the factory default values. See Table 42 for system configuration default values. zoning Clears the zoning database and deactivates the active zone set. The zoning configuration values (InteropAutosave, DefaultZone) remain unchanged. Notes The following tables specify the various factory default settings. Enter the Show Config Switch command to display switch configuration values.
Table 36 Port configuration defaults (continued) Parameter Default AutoPerfTuning True LCFEnable False MFSEnable False VIEnable False MSEnable True NoClose False PDISCPingEnable True Enter Show Config Threshold command to display threshold alarm configuration values.
Enter the Show Config Zoning command to display zoning configuration values. Table 38 Zoning configuration defaults Parameter Default InteropAutoSave True DefaultZone False Enter the Show Setup SNMP command to display SNMP configuration values. Table 39 SNMP configuration defaults Parameter Default SNMPEnabled True Contact Location Description McDATA 4Gb SAN Switch Trap [1-5] Address Trap 1: 10.0.0.254; Traps 2–5: 0.0.0.
Enter the Show Setup Services command to display switch service configuration values. Table 41 Services configuration defaults Parameter Default TelnetEnabled True SSHEnabled False GUIMgmtEnabled True SSLMgmtEnabled False EmbeddedGUIEnabled True SNMPEnabled True NTPEnabled False CIMEnabled True FTPEnabled True MgmtServerEnabled False Enter the Show Setup System command to display system configuration values.
Security command Description Opens a Security Edit session in which to manage the security database on a switch. See the Group command and the Securityset command. IMPORTANT: This command is available only with the SANtegrity Enhanced PFE key. Authority Admin session. The operands Active, History, Limits, and List are available without an Admin session.
save Saves the changes that have been made to the security database during a Security Edit session. Changes you make to any security set will not take effect until you activate that security set. See the Securityset command for information about activating a security set.
The following is an example of the Security List command: McDATA4GbSAN (admin-security) #> security list McDATA4GbSAN #> security list Active Security Information SecuritySet Group GroupMember ----------- ----- ----------No active securityset defined.
Securityset command Description Manages security sets in the security database. NOTE: This command is available only with the SANtegrity Enhanced PFE key. Authority Admin session and a Security Edit session. See the Security command for information about starting a Security Edit session. The Active, Groups, and List operands are available without an Admin session. You must end the Security Edit session before using the Activate and Deactivate operands.
list Displays a list of all security sets. This operand is available without an Admin session. remove [security_set] [group] Removes a group given by [group] from the security set given by [security_set]. If [security_set] is the active security set, the group will not be removed until the security set has been deactivated. rename [security_set_old] [security_set_new] Renames the security set given by [security_set_old] to the name given by [security_set_new].
Set command Description Sets a variety of switch parameters. Authority Admin session for all operands except Alarm, Beacon, and Pagebreak, which are available without an Admin session. Syntax set alarm [option] beacon [state] config [option] log [option] pagebreak [state] port [option] setup [option] switch [state] timezone Operands alarm [option] Controls the display of alarms in the session output stream or clears the alarm log. [option] can be one of the following: clear Clears the alarm log history.
setup [option] Changes SNMP and system configuration settings. See the Set Setup command. switch [state] Changes the administrative state for all ports on the switch to the state given by [state]. The previous Set Config Switch settings are restored after a switch reset or a reactivation of a switch configuration. [state] can be one of the following: online Places all ports online offline Places all ports offline. diagnostics Prepares all ports for testing.
Set Config command Description Sets switch, port, port threshold alarm, security, and zoning configuration parameters. The changes you make with this command are not retained when you reset or power cycle the switch unless you save them using the Config Save command. See the Config command.
Table 44 Set Config port parameters (continued) Parameter Description ARB_FF Send ARB_FF (True) instead of IDLEs (False) on the loop. The default is False. InteropCredit Interoperability credit. The number of buffer-to-buffer credits per port. 0 means the default (8) is unchanged. Changing interoperability credits is necessary only for E_Ports that are connected to non-FC-SW-2-compliant switches. Contact your authorized maintenance provider for assistance in using this feature.
security Initiates an edit session in which to change the security settings. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. Press q or Q to end the editing session. Table 45 describes the Set Config Security parameters. IMPORTANT: Table 45 This operand is available only with the SANtegrity Enhanced PFE key.
Table 46 Set Config switch parameters (continued) Parameter Description PrincipalPriority The priority used in the FC-SW-2 principal switch selection algorithm. 1 is high, 255 is low. The default is 254. ConfigDescription Switch configuration description. The configuration description can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is Default Config. InteropMode Interoperability mode.
threshold Initiates a configuration session by which to generate and log alarms for selected events. The system displays each event, its triggers, and sampling window one line at a time and prompts you for a value. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. These parameters must be saved in a configuration and activated before they will take effect. See the Config command for information about saving and activating a configuration.
zoning Initiates an edit session in which to change switch zoning attributes. The system displays each parameter one line at a time and prompts you for a value. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. Table 48 describes the zoning configuration parameters.
Examples The following is an example of the Set Config Port command: McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> config edit McDATA4GbSAN (admin-config) #> set config port 0 A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
The following is an example of the Set Config Switch command: McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> config edit McDATA4GbSAN (admin-config) #> set config switch A list of attributes with formatting and default values will follow. Enter a new value or simply press the ENTER key to accept current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
The following is an example of the Set Config Threshold command: McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> config edit McDATA4GbSAN (admin-config) #> set config threshold A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
The following is an example of the Set Config Zoning command. McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> config edit McDATA4GbSAN (admin-config) #> set config zoning A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
Set Log command Description Specifies the events to record in the event log and display on the screen. You determine what events to record in the switch event log using the Component, Level, and Port operands. You determine what events are automatically displayed on the screen using the Display operand. Alarms are always displayed on the screen.
display [filter] Specifies the log events to automatically display on the screen according to the event severity levels given by [filter]. [filter] can be one of the following values: Critical Critical severity level events. The critical level describes events that are generally disruptive to the administration or operation of the fabric, but require no action. Warn Warning severity level events.
Notes In addition to critical, warn, and informative severity levels, the highest event severity level is alarm. The alarm level describes events that are disruptive to the administration or operation of a fabric and require administrator intervention. Alarms are always logged and always displayed on the screen.
Set Port command Description Sets port state and speed for the specified port temporarily until the next switch reset or new configuration activation. This command also clears port counters. Authority Admin session except for the Clear operand. Syntax set port [port_number] bypass [alpa] clear enable speed [transmission_speed] state [state] Operands [port_number] Specifies the port. External ports are numbered 0 and 9; internal ports are numbered 1–8.
Set Setup command Description Manages configuration settings for Remote Authentication Dial-In User Service (RADIUS) servers, switch services, SNMP, and system configurations. Authority Admin session Syntax set setup radius services snmp system Operands radius Prompts you in a line-by-line fashion to configure RADIUS servers for user account and device authentication. Table 49 describes the RADIUS server configuration fields.
Table 49 RADIUS service settings (continued) Entry Description UserAuthServer Enable (True) or disable (False) this server for user account authentication. A user authentication RADIUS server requires a secure management connection (SSL). The default is True. AccountingServer Enable (True) or disable (False) this server for auditing of activity during a user session. When enabled, user activity is audited whether UserAuthServer is enabled or not. The default is False.
Table 50 Switch services settings (continued) Entry Description SSLEnabled Enables (True) or disables (False) secure SSL connections for management applications including McDATA Web Server, McDATA Element Manager, Application Programming Interface, and the CIM server. The default is False. • To enable secure SSL connections, you must first synchronize the date and time on the switch and workstation. • This service must be enabled to authenticate users through a RADIUS server.
SNMP Prompts you in a line-by-line fashion to change SNMP configuration settings. Table 51 describes the SNMP fields. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. Table 51 SNMP configuration settings Entry Description SNMPEnabled Enables (True) or disables (False) SNMP on the switch. The default is True. Contact Specifies the name of the person to be contacted to respond to trap events.
system Prompts you in a line-by-line fashion to change system configuration settings. Table 52 describes the system configuration fields. For each parameter, enter a new value or press Enter to accept the current value shown in brackets. NOTE: Table 52 Changing the IP address will terminate all Ethernet management sessions. System configuration settings Entry Description Eth0NetworkDiscovery Ethernet boot method: 1 - Static, 2 - Bootp, 3 - DHCP, 4 - RARP. The default is 1 - Static.
Examples The following is an example of the Set Setup RADIUS command: McDATA4GbSAN (admin) #> set setup radius A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the attributes for the server being processed, press 'q' or 'Q' and the ENTER key to do so.
The following is an example of the Set Setup SNMP command: McDATA4GbSAN #> admin start McDATA4GbSAN (admin) #> set setup snmp A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
The following is an example of the Set Setup System command: McDATA4GbSAN (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value. If you wish to terminate this process before reaching the end of the list press 'q' or 'Q' and the ENTER key to do so.
Show command Description Displays fabric, switch, and port operational information.
cimlistener [listener_name] Displays CIM indicator services listener information for the listener given by [listener_name]. If you omit [listener_name], the command displays all listeners. config [option] Displays switch, port, and zoning configuration attributes. See the Show Config command. domains Displays list of each domain and its World Wide Name in the fabric. fabric Displays list of each domain, symbolic name, World Wide Name, node IP address, and port IP address.
Table 53 Show Port parameters Entry Description AIinit Incremented each time the port begins AL initialization AIinitError Number of times the port entered initialization and the initialization failed Bad Frames Number of frames that have framing errors ClassXFramesIn Number of class x frames received by this port ClassXFramesOut Number of class x frames sent by this port ClassXWordsIn Number of class x words received by this port ClassXWordsOut Number of class x words sent by this port Cl
Table 53 Show Port parameters (continued) Entry Description RxOfflineSeq Number of offline sequences received. An OLS is issued for link initialization, a Receive & Recognize Not_Operational (NOS) state, or to enter the offline state.
• Show (About, Alarm, Backtrace, Chassis, Config Port, Config Security, Config Switch, Config Threshold, Dev, Dev Settings, Domains, Fabric, Log, Log Archive, Log Settings, Lsdb, Mem, Ns, Perf, Port, Setup Mfg, Setup Snmp, Setup System, Steering, Switch, Topology, Users) • Uptime • User Accounts • Whoami • Zoneset (Active, List) • Zoning (History, Limits, List) switch Displays switch operational information. Table 54 describes the switch operational parameters.
timezone Displays the current time zone setting. topology Displays all connected devices. users Displays a list of logged-in users. This is equivalent to the User List command. version Displays an introductory set of information about operational attributes of the switch. This operand is equivalent to the About operand.
The following is an example of the Show FDMI WWN command: McDATA4GbSAN #> show fdmi 21:00:00:e0:8b:09:3b:17 FDMI Information ---------------Manufacturer QLogic Corporation SerialNumber [04202 Model QLA2342 ModelDescription QLogic QLA2342 PCI Fibre Channel Adapter PortID 610000 NodeWWN 20:00:00:e0:8b:07:aa:bc HardwareVersion FC5010409-10 DriverVersion 8.2.3.10 Beta 2 (W2K VI) OptionRomVersion 1.21 FirmwareVersion 03.02.13. OperatingSystem SunOS 5.
The following is an example of the Show Interface command: McDATA4GbSAN #> show interface eth0 Link encap:Ethernet HWaddr 00:C0:DD:00:BD:ED inet addr:10.20.68.107 Bcast:10.20.68.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4712 errors:0 dropped:0 overruns:0 frame:0 TX packets:3000 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:415313 (405.5 Kb) TX bytes:716751 (699.
The following is an example of the Show Switch command: McDATA4GbSAN #> show switch Switch Information -----------------SymbolicName SwitchWWN BootVersion CreditPool DomainID FirstPortAddress FlashSize - MBytes LogFilterLevel MaxPorts NumberOfResets ReasonForLastReset ActiveImageVersion - build date PendingImageVersion - build date ActiveConfiguration AdminState AdminModeActive BeaconOnStatus OperationalState PrincipalSwitchRole BoardTemp (1) - Degrees Celsius SwitchDiagnosticsStatus SwitchTemperatureStatus
The following is an example of the Show Topology command for port 10: McDATA4GbSAN #> show topology 1 Local Link Information ---------------------Port PortID PortWWN PortType Int:1 620100 20:01:08:00:88:e0:aa:b5 F Remote Link Information ----------------------Device 0 PortID PortWWN NodeWWN PortType Description IPAddress 620100 50:05:08:b2:00:7b:a7:e2 50:05:08:b2:00:7b:a7:e0 N (NULL) 0.0.0.
Show Config command Description Displays switch, port, alarm threshold, security, and zoning for the current configuration. Authority None Syntax show config port [port_number] security switch threshold zoning Operands port [port_number] Displays configuration parameters for the port number given by [port_number]. External ports are numbered 0 and 9; internal ports are numbered 1–8. If [port_number] is omitted, all ports are specified. security Displays the security database Autosave parameter value.
The following is an example of the Show Config Switch command: McDATA4GbSAN #> show config switch Configuration Name: default ------------------AdminState Online BroadcastEnabled True InbandEnabled True FdmiEnabled True FdmiEntries 1000 DefaultDomainID 98 (0x62) DomainIDLock False SymbolicName McDATA4GbSAN R_A_TOV 10000 E_D_TOV 2000 PrincipalPriority 254 ConfigDescription Default Config ConfigLastSavedBy Initial ConfigLastSavedOn Initial InteropMode Standard The following is an example of the Show Config T
The following is an example of the Show Config Zoning command: McDATA4GbSAN #> show config zoning Configuration Name: default ------------------Zoning Configuration Information -------------------------------InteropAutoSave True DefaultZone False See also Set Config command, page 158 192 Command Line Interface
Show Log command Description Displays the contents of the log or the parameters used to create and display entries in the log. The log contains a maximum of 1200 entries. When the log reaches its entry capacity, subsequent entries overwrite the existing entries, beginning with the oldest. Authority None Syntax show log [number_of_events] component display [filter] level options port settings Operands [number_of_events] Specifies the number of the most recent events to display from the event log.
display [filter] Displays log events on the screen according to the component or severity level filter given by [filter].
The following is an example of the Show Log Options command: McDATA4GbSAN #> show log options Allowed options for log ----------------------FilterComponent All,None,NameServer,MgmtServer,Zoning,Switch,Blade,Port,Eport,Snmp FilterLevel Critical,Warn,Info,None DisplayLevel Critical,Warn,Info,None The following is an example of the Show Log command: McDATA4GbSAN #> show log [327][day month date time year][I][Eport Port:0/8][Eport State= E_A0_GET_DOMAIN_ID] [328][day month date time year][I][Eport Port: 0/8][F
Show Perf command Description Displays port performance in frames/second and bytes/second. If you omit the operand, the command displays data transmitted (out), data received (in), and total data transmitted and received in frames/second and bytes per second. Authority None Syntax show perf byte inbyte outbyte frame inframe outframe errors Operands byte Displays continuous performance data in total bytes/second transmitted and received. Press any key to stop the display.
The following is an example of the Show Perf Byte command: McDATA4GbSAN #> show perf byte Displaying bytes/sec (total)...
Show Setup command Description Displays the current SNMP and system settings. Authority None Syntax show setup mfg radius services snmp system Operands mfg Displays manufacturing information about the switch. radius Displays RADIUS server information. services Displays switch service status information. snmp Displays the current SNMP settings. system Displays the current system settings.
The following is an example of the Show Setup RADIUS command: McDATA4GbSAN #> show setup radius Radius Information -----------------DeviceAuthOrder RadiusLocal UserAuthOrder RadiusLocal TotalServers 1 Server: 1 ServerIPAddress ServerUDPPort DeviceAuthServer UserAuthServer AccountingServer Timeout Retries SignPackets Secret 10.20.11.
The following is an example of the Show Setup System command: McDATA4GbSAN #> show setup System Information -----------------Eth0NetworkDiscovery Eth0NetworkAddress Eth0NetworkMask Eth0GatewayAddress AdminTimeout InactivityTimeout LocalLogEnabled RemoteLogEnabled RemoteLogHostAddress NTPClientEnabled NTPServerAddress EmbeddedGUIEnabled See also Set Setup command, page 172 200 Command Line Interface system Static 10.20.92.246 255.255.255.0 10.20.92.1 30 0 True False 10.0.0.254 False 10.0.0.
Shutdown command Description Terminates all data transfers on the switch at convenient points and closes the Telnet session. Always power cycle the switch after entering this command.
Test command Description Tests ports using internal (SerDes level), external (transceiver), and online loopback tests. Internal and external tests require that the port be placed in diagnostic mode. See the Set Port State command for information about changing the port administrative state. While the test is running, the remaining ports on the switch remain fully operational.
Examples To run an internal or external port test, perform the following procedure: 1. Enter the following command and press Enter to start an Admin session. admin start 2. Enter the following command (x = port number) and press Enter to place the port in Diagnostics mode. set port x state diagnostics 3. Choose the type of port loopback test to run. Enter the following command to run an internal loopback test and press Enter.
Uptime command Description Displays the elapsed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activation does not reset the elapsed up time reported by this command.
User command Description Administers and displays user accounts. Authority Admin account name and an Admin session. The Accounts and List operands are available to all account names without an Admin session. Syntax user accounts add delete [account_name] edit list Operands accounts Displays all user accounts that exist on the switch. This operand is available to all account names without an Admin session. add Add a user account to the switch.
The following is an example of the User Add command: McDATA4GbSAN (admin) #> user add Press 'q' and the ENTER key to abort this command.
Whoami command Description Displays the account name, session number, and switch domain ID for the Telnet session.
Zone command Description Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit session. See the Zoning command for information about starting a Zoning Edit session. The List, Members, and Zonesets operands are available without an Admin session.
remove [zone] [member_list] Removes the ports/devices given by [member_list] from the zone given by [zone]. Use a to delimit ports/devices in [member_list]. [member_list] can have any of the following formats: • Domain ID and port number pair (Domain ID, Port Number). Domain IDs can be 1–31 in McDATA Fabric mode or 97–127 in Standard mode; port numbers can be 0–-255. • 16-character hexadecimal world wide port name (WWPN) with the format xx:xx:xx:xx:xx:xx:xx:xx.
The following is an example of the Zone Members command: McDATA4GbSAN #> zone members wwn_b0241f Current List of Members for Zone: wwn_b0241f --------------------------------50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f The following is an example of the Zone Zonesets command: McDATA4GbSAN #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ---------------------------------zone_set_1 See also Zoneset command, page 211 Zoning command, page 213 210 Command Line Interfa
Zoneset command Description Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit session. See the Zoning command for information about starting a Zoning Edit session. The Active, List, and Zones operands are available without an Admin session. You must close the Zoning Edit session before using the Activate and Deactivate operands.
Notes • A zone set must be active for its definitions to be applied to the fabric. • Only one zone set can be active at one time. • A zone can be a component of more than one zone set.
Zoning command Description Starts a Zoning Edit session in which to create and manage zone sets and zones. See the Zone command and the Zoneset command. Authority Admin session except for the Active, History, Limits, and List operands. The Clear operand also requires a zoning edit session. Syntax zoning active cancel clear edit history limits list restore save Operands active Displays information for the active zone set including component zones and zone members.
limits Displays the number of zone sets, zones, members per zone, and total members in the zoning database. This operand also displays the switch zoning database limits, excluding the active zone set, which are described in Table 55. This operand does not require an Admin session.
The following is an example of the Zoning Limits command: McDATA4GbSAN #> zoning limits Zoning Attribute ---------------MaxZoneSets MaxZones MaxTotalMembers MaxZonesInZoneSets MaxMembersPerZone Maximum ------1 2047 10000 2047 10000 Current ------1 17 166 19 10 23 9 16 5 5 3 3 8 8 24 8 13 21 3 4 [Zoning Name] ------------- D_1_JBOD_1 D_1_Photons D_2_JBOD1 D_2_NewJBOD_2 E1JBOD1 E2JBOD2 LinkResetZone LinkResetZone2 NewJBOD1 NewJBOD2 Q_1Photon1 Q_1_NewJBOD1 Q_1_Photon_1 Q_2_NewJBOD2 ZoneDomainPort ZoneFCAdd
The following is an example of the Zoning List command: McDATA4GbSAN #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -------------------------------wwn wwn_b0241f 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 21:00:00:e0:8b:02:41:2f wwn_23bd31 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:23:bd:31 wwn_221416 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:14:16 wwn_2215c3 50:06:04:82:bf:d2:18:c2 50:06:04:82:bf:d2:18:d2 10:00:00:00:c9:22:15:c3 Configured
Glossary Active firmware The firmware image on the switch that is in use Active zone set The zone set that defines the current zoning for the fabric Activity LED A port LED that indicates when frames are entering or leaving the port Administrative state State that determines the operating state of the port, I/O blade, or switch. The configured administrative state is stored in the switch configuration. The configured administrative state can be temporarily overridden using the CLI.
Fabric view file A file containing a set of fabrics that were opened and saved during a previous McDATA Web Server session Fan Fail LED An LED that indicates that a cooling fan in the switch is operating below standard Flash memory Memory on the switch that contains the chassis control firmware Force PROM mode See Maintenance Mode Frame Data unit consisting of a start-of-frame (SOF) delimiter, header, data payload, CRC, and an end-of-frame (EOF) delimiter FRU Field Replaceable Unit HAFM High Av
Power On Self Test (POST) Diagnostics that the switch chassis performs at start up Principal switch The switch in the fabric that manages domain ID assignments Product Feature Enablement key A password that you can purchase from your switch distributor or authorized reseller to enable particular features in your switch SFP Small Form-Factor Pluggable transceiver Small Form-Factor Pluggable (SFP) A transceiver device, smaller than a GigaBit Interface Converter, that plugs into the FC port SNMP Sim
Index A account name display 205, 207 factory 109 active zone set 49, 52 Active Zoneset data window 49 Admin account name 112 authority 112 Admin command 114 Admin session timeout 176 administrative state configured 79, 104 current 79, 104 port 104, 171 switch 79, 157 alarm configuration 75, 162 configuration defaults 148 configuration display 190 description 170 log 156, 180 Arbitrated Loop Physical Address 171 archive configuration 88 audience 9 authentication 130 device 66 trap 87 user 66 authority 112 a
zoning 57 defaults alarm configuration 148 port configuration 147 RADIUS configuration 149 security configuration 150 services configuration 150 Simple Network Management Protocol configuration 149 switch configuration 147 system configuration 150 zoning configuration 149 device authentication 66 nickname 51 scan 105 security 30 Devices data window 48, 70 document conventions 10 prerequisites 9 related documentation 9 documentation, HP web site 9 domain ID binding 132 description 79 display 181 lock 79 Dyna
Group command 129 GUI management service 83 H HAFM - See High Availability Fabric Manager hard reset 77 Hardreset command 134 hardware status 95 Heartbeat LED 95 help 17 Help command 135 help, obtaining 11, 12 High Availability Fabric Manager 13 History command 136 host bus adapter 181 hot reset 77 Hotreset command 137 HP authorized reseller 11 storage web site 12 Subscriber’s choice web site 11 technical support 11 I Image command 138 in-band management description 81 enable 38 indication service listene
node-to-node test 107 non-disruptive activation 92, 137 Non-Disruptive Code Load and Activation 77 NTP - See Network Time Protocol O online help 17 test 107 operating systems 13 orphan zone set 52 P page break 156 Passwd command 142 password change 142 factory 109 switch 142 user account 64 performance tuning 159 PFE key 91, 127 Ping command 143 port administrative state 104, 171 configuration 104, 158, 159 configuration defaults 147 configuration display 190 counters 171 displaying information 97 externa
security database clear 36, 151 display 151 display history 151 limits 151 security edit session cancel 151 initiate 151 revert changes 151 save changes 152 security set activate 37, 154 add member group 154 copy 154 create 33, 154 deactivate 38, 154 delete 154 delete member group 155 display 36, 155 display active 151, 154 display members 154 remove 36 rename 36, 155 Securityset command 154 SerDes level test 106 service listener 116 services 83 services configuration defaults 150 Set command 156 Set Config
arrange icons 24 data windows 24 description 18 usage 23 transceiver status 99 transmission speed 105 trap authentication 87 community 87 configuration 88 SNMP version 88 U upgrade 127 Uptime command 204 user account add 205 admin 109 admin account 109 create 62 default 61 delete 205 display 205 edit 205 list 205 logged in 185 modify 65 password 64 remove 63 security 30 User command 205 V version snapshot compare 39 export 39 save 39 Virtual Interface preference routing 159 W web server 174, 176 service