HP XP7 Remote Web Console Messages Abstract This document lists the error codes and error messages for the Remote Web Console for the HP XP7 Storage, and provides the recommended action for the error conditions.
© Copyright 2014 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 HP XP7 Storage messages and error codes....................................................6 HP XP7 Storage messages.........................................................................................................6 Message window format...........................................................................................................6 Advanced message window......................................................................................................
Part code 03205..................................................................................................................109 Part code 03222..................................................................................................................113 Part code 03305..................................................................................................................114 6 Message (part code group 04nnn)...........................................................120 Part code 04005.
Part code 10121...................................................................................................................262 Part code 10122...................................................................................................................263 Part code 10126...................................................................................................................265 13 Message (part code group 20nnn)..........................................................
1 HP XP7 Storage messages and error codes This chapter covers the various messages and error codes released by the storage system. HP XP7 Storage messages Figure 1-1 and Figure 1-2 show examples of typical message windows. Figure 1 Sample message window1 Figure 2 Sample message window2 Message window format Message level There are four message levels as shown below. Information Warning Fatal error The server is unable to accept the request from Remote Web Console.
Error code The error code is a message ID. In some cases, the number of digits in the message may not match the number of digits described in this manual, so if a part code having five or less digits is displayed in a message window, add some zeros to the beginning of the part code so as to make it a six-digit code. For example, when the four-digit error code "6023" is displayed in a message window, refer to the six-digit error code "006023" in this manual.
Remote Console-Remote Web Console error codes To resolve errors in Remote Web Console for XP7: • See the Troubleshooting chapter in the user guide for the product you were using when the error occurred (for example, Business Copy). • Look up the error message in the error code tables in this manual, and follow the recommended action for the error condition.
2 Message (part code group 00nnn) This chapter includes the error messages with the part code 00001 to 00810. Part code 00001 Table 1 Error codes (part code 00001) Part Code Error Number Error Message Recommended Action Severity Level 00001 001000 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00001 001001 A time-out error occurred. The array controller reboots automatically.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 004011 A network error occurred. The probable Log on again. A network error may occur when E cause is: the load of another application program working on the same PC with Storage Navigator is high. • A timeout error occurred during Increase the value of the RMI time-out period when communication with the SVP. network error occurs.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 005516 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 00001 005517 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 00001 005518 An error occurred during SVP processing.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level retrying, please contact HP Technical Support. 00001 006039 An error occurred during array controller If the problem persists despite retrying, please processing. contact HP Technical Support. E If this problem persists, please contact HP Technical Support. 00001 007003 The content of the management file of the audit log is invalid.
Table 1 Error codes (part code 00001) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00001 056555 The complete operation is performed to If the problem persists despite retrying, please all SIMs related to Audit Log. contact HP Technical Support. E 00001 056556 Complete operation of SIMs failed because the number of audit logs that had not been transferred exceeded the threshold. If the problem persists despite retrying, please contact HP Technical Support.
Table 2 Error codes (part code 00002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00002 002009 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00002 002010 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00002 002011 The SVP configuration is invalid.
Table 2 Error codes (part code 00002) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00002 006051 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00002 006502 Processing is in progress. If the problem persists despite retrying, please contact HP Technical Support. W 00002 006531 The SVP is busy. If the problem persists despite retrying, please contact HP Technical Support.
Part code 00003 Table 3 Error codes (part code 00003) Part Code Error Number Error Message Recommended Action Severity Level 00003 001040 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00003 001141 Processing is in progress. If the problem persists despite retrying, please contact HP Technical Support. W 00003 001900 Maintenance operation is executed by the SVP.
Table 3 Error codes (part code 00003) (continued) Part Code Error Number Error Message Recommended Action Severity Level W Communication busy. 00003 002033 The SVP is not ready yet, or an internal processing is being executed. Wait, then click [Refresh] on the [File] menu. When an error occurs during a login, wait, then log in again. 00003 002083 Unexpected error occurred. Please refresh the array configuration. The storage system status is invalid.
Part code 00004 Table 4 Error codes (part code 00004) Part Code Error Number Error Message Recommended Action Severity Level 00004 002006 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00004 006000 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00004 006001 A time-out error occurred. The array controller reboots automatically.
Part code 00006 Table 6 Error codes (part code 00006) Part Code Error Number Error Message Recommended Action Severity Level 00006 001005 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00006 001006 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00006 001007 An error occurred during SVP processing.
Part code 00010 Table 8 Error codes (part code 00010) Part Code Error Number Error Message Recommended Action 00010 006027 A network error occurred. The causes might be one of the following. You cannot connect to the SVP because of factors, E such as a network error or SVP error. Check the IP address. If the IP address is correct, close the browser (also close the browser of the storage list), and log in again after waiting a while. If the problem persists, please contact the HSSC.
Part code 00110 Table 11 Error codes (part code 00110) Part Code Error Number Error Message Recommended Action Severity Level 00110 005030 The displayed information has not been Check the microprogram version of the storage changed. Try again. system. W 00110 007060 An error occurred in the client logic. Check the microprogram version of the storage system. E 00110 007440 An error occurred during SVP processing. Check the microprogram version of the storage system.
Table 11 Error codes (part code 00110) (continued) Part Code Error Number Error Message Recommended Action Severity Level located on the Control Panel of the Remote Web Console to change the time-out period for Modify mode. 00110 057011 An error occurred regarding screen display. Please log off from Remote Web Console. After that, Please log off from Web Console. After that, E please log on to Web Console again and check whether configuration changes have been made correctly.
Part code 00122 Table 12 Error codes (part code 00122) Part Code Error Number Error Message Recommended Action 00122 105260 The free space for storing audit log files Download the Audit Log. is running out. Severity Level W Usage Rate xxx% 00122 105261 The free space for storing audit log files Download the Audit Log. has run out. The old audit log information will be overwritten. E Usage Rate xxx% 00122 107016 The audit log is not reset because the file of the audit log is not saved.
Table 13 Error codes (part code 00190) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00190 007052 The secret key file (.key file) cannot be backed up. If this problem persists, contact HP Technical Support. E 00190 007053 The signed public key certificate file (.crt If this problem persists, contact HP Technical file) cannot be updated. Support. E 00190 007054 The secret key file (.key file) cannot be updated.
Table 13 Error codes (part code 00190) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00190 057791 Work files cannot be deleted. If this problem persists, contact HP Technical Support. E 00190 057908 The web server cannot be restarted. If this problem persists, contact HP Technical Support. E 00190 057909 SSL communication is required for this function. If this problem persists, contact HP Technical Support. E Reconnect by using an https connection.
Part code 00221 Table 14 Error codes (part code 00221) Part Code Error Number Error Message Recommended Action Severity Level 00221 105007 The re-entered password does not match Verify the settings, and then retry the operation. the one entered previously. W 00221 105008 The re-entered secret does not match the Verify the settings, and then retry the operation. one entered previously.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105318 The domain name of authentication server is not input. This is a compulsory input item. W 00222 105319 The domain name of authentication server is too long. Enter with 1 to 255 characters. W 00222 105320 Invalid characters are used in the domain name of authentication server. Enter with alphanumeric characters and symbols( W - . ).
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105338 The password of authentication server is not input. This is a compulsory input item. W 00222 105339 The password of authentication server is too long. Enter with 1 to 256 characters. W 00222 105340 Invalid characters are used in the specified password of authentication server. Enter with alphanumeric characters and symbols( W ! # $ % & ' ( ) * + - .
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105357 Other than the numeric characters are input to the secondary port number of authentication server. Enter with numeric characters. W 00222 105358 The value that can be input to the secondary port number of the authentication server is 1 to 65535. Set a value within the range.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message 00222 105379 Invalid characters are used in the Enter with alphanumeric characters and symbols( W specified domain name of external user - . ). group mapping. 00222 105380 The base DN of external user group mapping is not input. This is a compulsory input item. W 00222 105381 The base DN of external user group mapping is too long. Enter with 1 to 255 characters.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 105398 The number of retries for the external user group mapping is not input. This is a compulsory input item. W 00222 105399 Other than the numeric characters are input to the specified number of retries of authentication server. Enter with numeric characters. W 00222 105400 The value that can be input to the Set a value within the range.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action 00222 105417 Invalid characters are used in the Enter with alphanumeric characters and symbols( W specified user name for connecting test. ! # $ % & ' * + - . / = ? @ ^ _ `{ | } ~ ). 00222 105418 The password for connecting test is not input. This is a compulsory input item. W 00222 105419 The password for connecting test is too long. Enter with 1 to 128 characters.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106055 Failed to delete the user account. Check the following contents. W • If the specified user exists. • If there is no built-in user in the specified users. • If there is a valid local authentication user who belongs to the Administrator User Group except the specified user, then retry the operation.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 106069 You cannot remove the selected users, because they will not belong to any groups. Check the number of the groups which the selected users belong to. W 00222 106070 The Built-in user cannot be removed. Select the users whose types are not the Built-in. W 00222 106071 The selected users could not be removed.
Table 15 Error codes (part code 00222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00222 107014 Failed to get the user group information. If the problem persists despite retrying, please contact HP Technical Support. W 00222 107017 An error occurred while accessing the alert information. Try again. If this problem persists, contact HP Technical Support. E 00222 107024 An error occurred during SVP processing.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00290 005130 No role (Support personnel). The following role is required for this operation. - • Maintenance personnel (for vendors) Contact the security administrator, and then register the user to an user group which has a necessary role. 00290 005140 No role (Storage administrator [Initial configuration]). The following role is required for this operation.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00290 006500 Failed to Backup. If the same error occurs again despite retrying, please contact HP Technical Support. - 00290 006610 The external authentication file cannot be opened. If this problem persists, contact HP Technical Support. E 00290 006710 The external application link file cannot If this problem persists, contact HP Technical be opened. Support.
Table 16 Error codes (part code 00290) (continued) Part Code Error Number Error Message Recommended Action Severity Level the resource that the user could treat after the user account information was restored with Restore File would differ from that of backed up.
Table 17 Error codes (part code 00305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00305 007206 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00305 007207 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 00305 007208 An error occurred during SVP processing.
Table 19 Error codes (part code 00322) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00322 205029 The combination of the selected rows is Select communities and IP Addresses so that invalid. values of all of the selected communities or IP Addresses are the same. W 00322 205030 The form of the community is wrong. Check the settings. W 00322 205031 No more managers can be registered because the number of registered IP addresses has reached the maximum.
Table 20 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level W >>>>> Thin Provisioning Smart Tiers Z >>>>> Smart Tiers Smart Tiers Z >>>>> Thin Provisioning Z Fast Snap >>>>> Thin Provisioning 00405 005074 The specified program product ID is invalid. Retry the operation. If this problem persists, contact HP Technical Support. 00405 005075 This key code is invalid. Any of the following is thought to be the problem.
Table 20 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level Remove or disable the related program product first. W >>>>> Thin Provisioning Z Fast Snap >>>>> Thin Provisioning 00405 005078 To remove or disable this program product, you must remove or disable a different program product first.
Table 20 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00405 005525 Data Retention cannot be removed Release the S-VOL Disable setting or the reserved W because the S-VOL Disable setting or the volume setting. reserved volume setting remains. 00405 006012 An error occurred during SVP processing. 00405 006022 The information in the license file cannot Verify the information in the license file, and then W be acquired.
Table 20 Error codes (part code 00405) (continued) Part Code Error Number Error Message Recommended Action Severity Level Purchase a license for the program product to continue the use. W licensed capacity during the valid period. 00405 066018 The program product was removed because the term license is expired. 00405 075012 A permanent license is necessary to Install a permanent license (excluding the frame install before installing the meter license. unlimited).
Table 23 Error codes (part code 00422) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00422 205005 The license key file name exceeds 200 characters. Select a different file with the name within 200 characters. W 00422 205006 The specified program product is not installed. Verify the license status. W 00422 205007 The specified program product cannot be enabled because the status is not Install (Disable). Verify the license status.
Part code 00605 Table 24 Error codes (part code 00605) Part Code Error Number Error Message Recommended Action Severity Level 00605 002011 The status of the storage system requires Check the status of the storage system E the maintenance (if the storage system is blocked, shared memory (for example, the storage system is is inconsistent, or some other factor). blocked, the shared memory is If this problem persists, please contact HP inconsistent, or some other factor). Technical Support.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level Journal, or Continuous Access Journal Z is defined. 00605 002517 A pair of Business Copy, Business Copy Release the pair definition, and then retry the Z, Compatible FlashCopy, Compatible operation. When quick split is in progress, FlashCopy SE, or Fast Snap is defined. suspend the pair, and then release it. W 00605 002518 A pair of Business Copy or Business Copy Z is defined.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 008102 This function is not supported. Check whether the DKCMAIN microcode version W and the SVP microcode version are mismatched. 00605 008122 Another maintenance processing is in progress. Wait for a while, then retry the operation.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 058407 The reserved volume setting for Release the journal volume setting for Continuous W Continuous Access Journal or Continuous Access Journal or Continuous Access Journal Z, Access Journal Z is defined. then retry the operation. 00605 058409 The cache mode cannot be changed when the Disconnect External Storage Systems or the Disconnect External Volume is in progress.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 065801 There are no setting lines of the ExG. Check the setting of ExG. W 00605 065802 There are no setting lines of TargetPathGroup. Check the contents of the spreadsheet. W 00605 066011 The number of external LUs that can be connected from a single port has exceeded the maximum value. Delete unnecessary external LU(s), then retry the operation.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 066568 Multiple operation tags are defined. Check the contents of the spreadsheet. W 00605 066675 The syntax of parameter is invalid. Check the syntax of parameter. W 00605 066692 The volume in the local storage system cannot be operated. Specify the volume in an external storage system. W 00605 066693 A correct parameter as a data transfer volume is not set.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 066749 The number of paths has reached the maximum number. Check the setting of path. W 00605 066750 The specified WWN is not registered. Check the specified WWN. W 00605 066751 The specified WWN has already been specified. Excluding the overlapping setting, then retry the operation.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level system and the migration target storage system. 00605 077142 The operation cannot be performed because the multi-array virtualization function of the specified LDEV ID is enabled. Disable the multi-array virtualization function, and W then retry the operation. 00605 077143 The specified LDEV capacity is not valid. Verify the setting of the LDEV capacity.
Table 24 Error codes (part code 00605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00605 078057 The specified LDEV belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the specified LDEV. W 00605 078058 The specified external volume contains an LDEV that belongs to a resource group that you do not have permission to access.
Table 26 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00622 105042 [Delete] is clicked without selecting any row. Select one or more table rows. W 00622 105084 The setting cannot be changed, because Check the settings. an invalid value has been input. W 00622 105204 A necessary program product is not installed, or insufficient permissions to execute editorial operation. Install a necessary program product.
Table 26 Error codes (part code 00622) (continued) Part Code Error Number Error Message 00622 105262 LDEV Name can not be registered Edit LDEVs, or recreate external volumes if you because there is a volume that failed to want to register the LDEV Name. be created as an external volume. W 00622 105265 Insufficient logical volumes to map the external volumes. Reduce the number of external volumes to be mapped, then retry the operation.
Table 26 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00622 105278 The port that is connected to the specified external volume belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the port that is connected to the specified external volume. W 00622 105279 The specified emulation type cannot be Check the capacity of the external volumes.
Table 26 Error codes (part code 00622) (continued) Part Code Error Number Error Message Recommended Action 00622 107002 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 00622 107003 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support.
Part code 00722 Table 28 Error codes (part code 00722) Part Code Error Number Error Message Recommended Action Severity Level 00722 205042 The Primary Server and the Secondary Server have the same settings. Set a different IP Address or Port Number. W 00722 205043 The value you entered for the Port Number is not within the allowable range (1 to 65535). Check the settings. W 00722 205044 The value you entered for the Timout is not within the allowable range (1 to 120). Check the settings.
Table 29 Error codes (part code 00726) (continued) Part Code Error Number Error Message Recommended Action Severity Level 00726 205006 Failed to send a test message to xxx. Verify the following. E • If the client certificate is correct. • If the root certificate of the server side is correct. • If the LAN is connected. 00726 205007 The client certificate or root certificate of Verify the following. Upload it again, and then the correct xxx is not uploaded, or a send a test message.
3 Message (part code group 01nnn) This chapter includes the error messages with the part code 01005 to 01310. Part code 01005 Table 31 Error codes (part code 01005) Part Code Error Number Error Message Recommended Action Severity Level 01005 001002 The specified volume cannot be set as a command device because it is used as the volume of Continuous Access Synchronous, Continuous Access Journal, Business Copy, Auto LUN, or Fast Snap. Please select another volume.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001022 Invalid host mode. The configuration information has been already changed. Check the settings, and request the setting of the configuration information again. W 01005 001023 Invalid Fibre address. The configuration information has been already changed. Check the settings, and request the setting of the configuration information again.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action 01005 001116 When registering WWN, the value is Specify a different volume, and then retry the not specified. Or, zero is set as the value operation. of WWN. Be sure to set the WWN value before requesting the configuration change. W 01005 001123 Command device security cannot be set The configuration information has been already to the specified volume because the changed.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 001174 The specified host ID is already registered. Correct the settings, then retry. W 01005 001177 The specified host is already registered. Correct the settings, then retry. W 01005 001178 An incorrect host name was specified. Correct the settings, then retry. W 01005 001180 An error occurred during SVP processing.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Please refresh the array configuration. The port type is incorrect. 01005 001367 The host mode "4C" is used for a host Check the settings, then retry. group connecting to volumes that cannot be used for HP XP External Storage. W 01005 001368 Error happened before the change was Check the settings, then retry. processed.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Contact HP Technical Support. W Execute the changing operations separately. 01005 001929 Releasing the Host Mode Option 61 is disabled. 01005 001930 The operation cannot be performed Specify a volume other than the external volume because the specified volume is used as mapped for the online data migration, and then an external volume that is mapped for retry the operation.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 002097 The host specified by the WWN is performing I/O operations. Specify a different volume, and then retry the operation. W 01005 002098 Error happened after some change When the same problem persists, please contact E occurred. Please refresh the array HP Technical Support. configuration.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level An error occurred during SVP processing. 01005 006036 Error happened before the change was If this problem persists, please contact HP processed. Technical Support. E An error occurred during SVP processing. 01005 006040 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 31 Error codes (part code 01005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01005 056303 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 057101 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 01005 057102 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 01022 Table 32 Error codes (part code 01022) Part Code Error Number Error Message Recommended Action 01022 105009 All the check boxes are cleared. Check the check boxes for the items that you want W to change, then retry the operation. 01022 105010 The host group name is not set. Enter the host group name from 1 to 64 characters. W 01022 105011 The number of characters specified in the host group name has exceed the maximum. Enter the host group name from 1 to 64 characters.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level same port, or it exists in the [Selected Hosts] table. 01022 105026 The processing cannot be done because Check if there is a target host to be set in the of no data in the [Selected Hosts] table. [Selected Hosts] table. When there is not, add host(s) and retry the operation. When there is, close the window(s) and refresh it, then retry again.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105046 HBA WWN cannot be converted into hexadecimal. Specify the HBA WWN with 16 digits in hexadecimal. W 01022 105047 The length of the host name is incorrect. Enter the host name within 1 to 64 characters. W 01022 105048 An invalid character is used in the host name. W 01022 105049 You are trying to register the same host Check the settings.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 105085 The setting cannot be changed, because Check the settings. the value of UUID is outside the range. W 01022 105086 The input value of the starting LUN ID is Check the settings. outside the range. W 01022 105087 The LUN ID cannot be set, because the value is outside the range. Check the settings. W 01022 105088 The table column is not selected.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message 01022 105277 Some LDEVs or Host Groups that are not Click [OK], then continue the operation. available for LUN path setting are excluded from the choices. W 01022 105296 The specified port belongs to a resource Log out, and then log back in with access to the group that you do not have permission resource group containing the specified port. to access.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 106506 The specified LU does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 01022 106510 The specified host does not exist in the configuration. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message 01022 108005 There is a volume, which is set as Check the settings. reserved by Data Retention, in the target path information. W 01022 108006 The specified LDEV is a reserved volume Check the settings. of Data Retention. W 01022 108007 The specified LDEV is set other than the Read/Write (S-VOL enabled) of Data Retention. Check the settings.
Table 32 Error codes (part code 01022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01022 205019 The FC-AL topology cannot be set to the Check the settings. port whose transfer rate is 16 Gbps. W 01022 205053 The virtual model types or the serial numbers of the selected LDVEs are different. Check the settings.
Table 33 Error codes (part code 01305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 01305 066576 Any operation tag to the program product is not set. Check the contents of the spreadsheet. E 01305 066577 Version number or program product of the declaration is not correct. If the problem persists despite retrying, please contact HP Technical Support. E 01305 066578 There was an error while executing the Check the contents of the spreadsheet. spreadsheet.
4 Message (part code group 02nnn) This chapter includes the error messages with the part code 02005. Part code 02005 Table 35 Error codes (part code 02005) Part Code Error Number Error Message Recommended Action Severity Level 02005 001009 Error happened before the change was The configuration information has been already processed. The emulation type of the changed. Check the settings, and request the volumes is not for open systems, or the setting of the configuration information again.
Table 35 Error codes (part code 02005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 02005 002032 An error occurred while connecting to the storage system. A communication error occurs. If the same error occurs despite retrying, please contact HP Technical Support. E 02005 002082 Error happened after some change occurred. Please refresh the array configuration. Processing is disabled because the host is mounted or the device is reserved.
Table 35 Error codes (part code 02005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 02005 065660 Error happened before the change was Associate the Thin Provisioning volume with a processed. pool, then retry the operation. W The Thin Provisioning volume is not associated with a pool. 02005 065704 Error happened before the change was Associate the Thin Provisioning volumes with the processed. same pool, then retry the operation.
5 Message (part code group 03nnn) This chapter includes the error messages with the part code 03005 to 03305. Part code 03005 Table 36 Error codes (part code 03005) Part Code Error Number Error Message 03005 001910 The specified volume contains Fast Snap Check the setting of the specified volumes. pair. W 03005 001911 The specified volume contains Pool-VOLs. W 03005 002011 The status of the storage system requires Please contact HP Technical Support.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level • The processor status is changing. • The cache status is changing. • LDEV shredding is in progress. • The configuration is changing. 03005 002200 The Concurrent Copy or the Compatible If the Concurrent Copy or the Compatible XRC W XRC operation is in progress in the operation is in progress in the target volumes, target volumes.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 002520 A Auto LUN pair is defined. Delete the pair definition, and then retry the operation. W 03005 002521 An Auto LUN pair is defined. Release the pair definition. W 03005 003003 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03005 005010 An error occurred during SVP processing.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 008002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03005 008100 An error occurred while connecting to the storage system. If this problem persists, please contact HP Technical Support. E 03005 008102 This function is not supported.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 057102 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03005 058460 The logical volume cannot be registered, Install the logical volume. because it is not installed. 03005 058461 The specified operation cannot be done, Restore the blockade status of the logical volume. W because the logical volume is blocked.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level memory available on the shared memory If the additional shared memory is already for the V-VOL management area. installed, the capacity of pools and V-VOLs has reached the maximum. In this case, delete unnecessary pools and V-VOLs, and then retry the operation. 03005 058475 The PCB for fibre port is not installed. Install the PCB for fiber port, and retry the operation.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 065690 The specified volumes contain volumes that are being quick formatted. Check the settings and retry the operation. W 03005 065691 Preparing for quick format. Check the status and wait until the status changes W to a status that maintenance is possible. 03005 065692 The specified volumes contain volumes that quick format cannot be executed.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 068786 A parity group that is not blocked is included in the specified parity groups. Check the status of the specified parity groups.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action 03005 068824 The specified volume is currently used by Continuous Access Synchronous, Continuous Access Synchronous Z, or External Storage Access Manager. Wait until the processing of Continuous Access E Synchronous, Continuous Access Synchronous Z, or External Storage Access Manager is completed, and then retry the operation. If this problem persists, please contact HP Technical Support.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action • Auto LUN • Auto LUN • Continuous Access Synchronous • Continuous Access Synchronous • Continuous Access Journal • Continuous Access Journal Severity Level 03005 078010 The specified operation cannot be executed, because the maximum reserved pool capacity is incorrect. Check the maximum reserved pool capacity, then W retry the operation.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078030 The frequency distribution data cannot be obtained. There is no monitoring information of the specified THP V-VOL because one of the following is performed: Collect the information, and then retry the operation. W Recover the blocked MP Blade, then specify it.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action 03005 078044 The operation cannot be executed because the specified pool has one of the following problems. Take any of the following actions, and then retry E the operation. If this problem persists, contact HP Technical Support. • The status of the specified Pool-VOL is not normal. • Restore the pool volume to the normal status.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action 03005 078062 Failed to delete the pool. Pools cannot be deleted when they are in the following status: Delete the following pairs or volumes if any, and W then retry the operation. • Pairs of Fast Snap are remaining. • Volumes of Thin Provisioning are remaining.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078114 The operation failed, because the start Check the status of the pool, then retry the of tier relocation operation was specified operation. for a pool in tier relocation operation, or the stop of tier relocation operation was specified for a pool not in tier relocation operation.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 078268 The operation cannot be performed due Specify a pool volume, or specify a pool volume W to one of the following reasons: that is set to the specified pool, and then retry the operation. • The specified volume is not a pool volume. • The specified pool volume is not set to the specified pool. 03005 078269 The specified pool ID is invalid.
Table 36 Error codes (part code 03005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03005 107103 This function is not available. DKA Encryption is required. Install the required program product. W 03005 108100 A parameter error occurred on the storage system. If this problem persists, contact HP Technical Support. E 03005 108102 The number of created keys exceeds the Verify the setting. maximum. W 03005 108103 The key cannot be deleted.
Part code 03010 Table 37 Error codes (part code 03010) Part Code Error Number Error Message Recommended Action Severity Level 03010 001046 The number of Cache Residency settings Reduce the number of Cache Residency settings, W has exceeded the maximum number of then retry the operation. available Cache Residency Areas.
Table 38 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105152 An LDEV in Normal or Quick Formatting Check the settings. status is selected. E 03022 105153 The specified value is outside the range. Check the settings. W 03022 105154 0 cannot be specified. Check the settings. W 03022 105155 A value other than the numerical value is specified. Check the settings.
Table 38 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105178 An unblocked LDEV is selected for the target LDEV to be operated. Check the settings. W 03022 105179 An LDEV in Normal or Quick Formatting Check the settings. status is selected. W 03022 105181 Quick formatting cannot be performed because the number of parity groups exceeds 72. Check the settings.
Table 38 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105250 Two or more Basic exists together to External. Check the settings. E 03022 105259 There is no output file. Please operate it again after executing Shredding. E 03022 105263 An LDEV that the Snapshot is set has been selected. Check the settings. W 03022 105267 Volumes that can be shredded in the selected volumes will be displayed. Click [OK] to shred.
Table 38 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level group to which the user has no access right. 03022 105309 The specified pool cannot be used Verify the resources allocation for the user with because the user has no access right to security administrator role. a resource group to which the pool belongs. 03022 105312 Open and mainframe pools cannot be selected at the same time.
Table 38 Error codes (part code 03022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03022 105452 The number of virtual volumes that can be registered in the storage system has reached the maximum. Verify the device configuration of the storage system. W 03022 105453 There are not enough usable LDEV IDs in the selected free area. Decrease the number of the selected free areas or provide the number of usable LDEV IDs.
Part code 03121 Table 39 Error codes (part code 03121) Part Code Error Number Error Message Recommended Action 03121 105001 The specified Tiering Policy cannot be Check the Tiering Policy setting. set due to one of the following reasons: Severity Level W • The Tier1 Min value exceeds the Tier1 Max value. • The Tier3 Min value exceeds the Tier3 Max value. • The total value of the Tier1 Min value and the Tier3 Min value exceeds 100%.
Table 40 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106011 The number of prefix characters of the pool name is invalid. Enter prefix characters with a valid number for the pool name. W 03122 106012 The specified prefix characters for a pool Check the prefix characters of pool name, then name contain an invalid character(s). retry the operation. W 03122 106013 The initial number of specified pool name is not input.
Table 40 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106033 The operation cannot be performed because at least one Fast Snap pool is selected. Verify the available pool types, select pools, and W then retry the operation. 03122 106034 The shrinking operation cannot be performed on the specified pool due to one of the following reasons. Check the following settings, and then retry the operation.
Table 40 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106091 The warning threshold is not input. Check the setting of warning threshold, then retry W the operation. 03122 106093 The depletion threshold is not input. Check the setting of the depletion threshold, then W retry the operation. 03122 106094 More than one volume type (drive type, To continue, click [OK]. Otherwise, click [Cancel].
Table 40 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 106107 The operation cannot be executed because there is only one tier in the specified pool. Check the configuration of tier in the pool. W 03122 106108 The specified LDEVs cannot be set as Select LDEVs allocated to the same resource pool volumes in the same pool because group. the LDEVs are allocated to different resource groups.
Table 40 Error codes (part code 03122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03122 107023 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 03122 200001 The pool of the specified capacity cannot be created. Check the specified value of the Total Capacity, and then retry the operation.
Table 41 Error codes (part code 03205) (continued) Part Code Error Number Error Message 03205 002203 Processing cannot be performed because Release the setting of Volume Security, then retry W of Volume Security settings. the operation. 03205 002515 A pair of Continuous Access Release the pair definition, or delete command W Synchronous, Continuous Access devices defined by Business Continuity Manager, Synchronous Z, Continuous Access and then retry the operation.
Table 41 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 008140 The configuration of Compatible Release the configuration definition of Compatible W FlashCopy or Compatible FlashCopy SE FlashCopy or Compatible FlashCopy SE, and then is defined. retry the operation. 03205 008958 An error occurred on the DKC side. If this problem persists, please contact HP Technical Support. E 03205 008966 An error occurred on the DKC side.
Table 41 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 066506 Specified SSID has already been used. Check the setting of SSID. W 03205 066508 The specified LDEV capacity is invalid. Check the setting of LDEV capacity. W 03205 066510 The specified emulation type cannot be Check the setting of the specified emulation type. W used. 03205 066512 Specified CLPR is not mounted. Check the setting of CLPR.
Table 41 Error codes (part code 03205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03205 078059 The pool associated with the specified LDEV contains LDEVs that belong to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the LDEVs in the associated pool. W 03205 078061 The specified emulation type is different Specify the same emulation type as the pool.
Table 42 Error codes (part code 03222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03222 105202 The status information of the specified Execute refresh. LDEV does not exist in the configuration. E 03222 105203 The detailed information of the pool that Execute refresh. is associated with the specified LDEV does not exist in the configuration. E 03222 105211 The selected volume cannot be enhanced Please decrease the number of selections of any further.
Table 43 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 001043 An operation is specified for the uninstalled VDEV. Correct the settings, then retry the operation. W 03305 001044 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 001045 The specified Subsystem ID already exists. Specify another SSID. Correct the specified content, and issue the request again.
Table 43 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 002005 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 002011 The status of the storage system requires If this problem persists, please contact HP maintenance (for example, the storage Technical Support. system is blocked, the shared memory is inconsistent, or some other factor).
Table 43 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level • LDEV shredding is in progress. • The configuration is changing. 03305 002200 The Concurrent Copy or the Compatible Cancel the Concurrent Copy job or delete a XRC operation is in progress in the Compatible XRC pair via the host. target volumes. W 03305 002201 Processing cannot be performed because Specify a different volume, and then retry the of Data Retention settings.
Table 43 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 03305 006011 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 03305 006022 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 43 Error codes (part code 03305) (continued) Part Code Error Number Error Message Recommended Action 03305 075043 The operation cannot be performed Specify a volume other than the external volume because the specified volume is used as mapped for the online data migration, and then an external volume that is mapped for retry the operation. the online data migration. W 03305 075044 The VLL operation does not support the specified emulation type. Specify a different emulation type.
6 Message (part code group 04nnn) This chapter includes the error messages with the part code 04005 to 04010. Part code 04005 Table 44 Error codes (part code 04005) Part Code Error Number Error Message Recommended Action Severity Level 04005 005010 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 04005 005040 The number of requests exceeds the maximum number that can be processed.
Table 44 Error codes (part code 04005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 04005 055245 The number of cache residency areas set for the CLPR exceeds the maximum available number of cache residency areas. Specify a different volume, and then retry the operation. W CLPR No:xxx SLPR No:xxx 04005 055246 The total number of cache residency Specify a different volume, and then retry the areas set for the CLPRs does not match operation.
Table 44 Error codes (part code 04005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 04005 055542 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 04005 055576 An LDEV number that does not apply to Check the setting(s). the selected CU group has been specified. E 04005 056526 The resources of other SLPR(s) cannot be If the problem persists despite retrying, please accessed.
Table 45 Error codes (part code 04010) (continued) Part Code Error Number Error Message Recommended Action 04010 005010 The value specified as the ending Correct the values specified as the starting and address for the data to be placed in ending addresses, then retry the operation. cache is smaller than the value specified as the starting address. W 04010 005011 The value specified as the Number of Cache Residency Areas is equal to or less than one cylinder.
7 Message (part code group 05nnn) This chapter includes the error messages with the part code 05105 to 05310. Part code 05105 Table 46 Error codes (part code 05105) Part Code Error Number Error Message Recommended Action Severity Level 05105 002002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05105 002003 An error occurred during SVP processing. Use the SVP to check if the DKC is in the normal status, then retry.
Table 46 Error codes (part code 05105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05105 006092 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05105 006501 There is no monitoring data. Change the monitor switch to ON, and accumulate the data. W 05105 007007 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Part code 05107 Table 47 Error codes (part code 05107) Part Code Error Number Error Message Recommended Action Severity Level 05107 005099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 05107 006012 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 49 Error codes (part code 05122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05122 105105 There is no editable WWN as a target of monitoring. Click [OK]. W 05122 105106 The WWN cannot be added, because that WWN Name is duplicated in the WWN to be monitored. Check the additional WWN, and edit the duplicated WWN Name. W 05122 105107 The content has not been edited. Edit the WWN to be monitored.
Table 49 Error codes (part code 05122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05122 105254 No more graph items can be added Set the number of graph items per one graph because the number of graph items that panel to 8 or less. can be displayed in one graph panel has reached the maximum. 05122 107001 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001122 The volume(s) is already being used by Compatible XRC. Select a different volume, and then retry the operation. W 05205 001207 The volume types do not match. Retry the operation. If this problem persists, contact HP Technical Support. W 05205 001210 The shared memory to set a plan is insufficient. Install the shared memory if it is possible.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message 05205 001229 The specified volume(s) are already used See "Supported and prohibited source and target W by Business Copy Z or Business Copy. volumes" in the AutoLUN User Guide if the volumes of Business Copy for Mainframe or of Business Copy can be migrated. 05205 001230 The specified volume(s) are already used Select a different volume, and then retry the by Business Copy Z or Business Copy. operation.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 001611 The specified volume has Read Only/Protect/SVOL Disable setting of Data Retention. Release the Read Only/Protect/S-VOL Disable setting of Data Retention Utility. W 05205 002003 The SVP is busy (internal processing), or Wait until the internal processing or the W a maintenance operation is in progress.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 006036 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 05205 006050 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 05205 006502 Processing in progress. Wait for a while, and then retry the operation. If W this problem persists, contact HP Technical Support.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 007411 Failed to write to the plan file. Retry the operation. If this problem persists, contact HP Technical Support. W 05205 007412 The file contains invalid data. Retry the operation. If this problem persists, contact HP Technical Support. E 05205 007413 The file contains invalid data. Retry the operation. If this problem persists, contact HP Technical Support.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 008671 The sizes of the source and the target volumes are not equal. Select the volumes with the same size for the migration source and target, and then retry the operation. W 05205 008971 An error occurred during SVP processing. If this problem persists, contact HP Technical Support.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 055522 The specified volume(s) are already being used as V-VOL(s). Select a different volume, and then retry the operation. W 05205 055523 The specified volume(s) are already being used as Pool-VOL(s). Select a different volume, and then retry the operation. W 05205 055524 The specified volumes are already usedas the volumes of Fast Snap.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 057101 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 05205 057102 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 05205 058451 The storage system is busy (internal processing). Retry the operation. If this problem persists, contact HP Technical Support.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 065709 The specified following volumes cannot be migrated. The migration source volume is shared by a P-VOL or an S-VOL of Continuous Access Journal or Continuous Access Synchronous, and the migration target volume is a Thin Provisioning volume. Select a different volume, and then retry the operation.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 075019 The volume specified as a migration target cannot be used because its emulation type is 3390-V. Select a different volume, and then retry the operation.
Table 50 Error codes (part code 05205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05205 078057 The operation failed, because the current Check the microcode version of the storage microcode version does not support the system. capacity of the specified target volume. W 05205 078058 The operation failed, because the current Check the microprogram version of the storage microcode version does not support the system. capacity of the specified reserved volume.
Table 51 Error codes (part code 05221) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05221 209010 Are you sure you want to delete all the operational histories? To continue, click [OK]. Otherwise, click [Cancel]. W 05221 209011 Are you sure you want to delete the selected rows? To continue, click [OK]. Otherwise, click [Cancel].
Table 52 Error codes (part code 05222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05222 206100 The pool usage of the target volume To continue, click [OK]. Otherwise, click [Cancel]. W exceeds the depletion threshold. Do you want to continue this operation? 05222 206101 This migration plan cannot be performed Increase the pool capacity associated with the because the pool usage associated with target volume. the target volume is 100 percent or more.
Part code 05305 Table 53 Error codes (part code 05305) Part Code Error Number Error Message Recommended Action Severity Level 05305 001064 The specified WWN is already being used. Correct the specified contents, and request the setting of the configuration information again. W 05305 001258 This port is not properly equipped. Retry the same operation. If nothing changes, please contact HP Technical Support. W 05305 002002 An error occurred during SVP processing.
Table 53 Error codes (part code 05305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05305 005113 The specified WWN is registered on a PFC group. Check the specified content, and retry. W 05305 005114 Target WWNs have different attribute. Check the specified content, and retry. W 05305 005204 This function is not available.Performance Monitor is required. Install the necessary program product. E 05305 006000 An error occurred during SVP processing.
Table 53 Error codes (part code 05305) (continued) Part Code Error Number Error Message Recommended Action 05305 056303 An error occurred during SVP processing. The error may be caused by a temporary E communication failure. Reboot the SVP or click [Refresh All] on the File menu of Remote Web Console and refresh the configuration information to recover from the error. If this problem persists, please contact HP Technical Support.
Table 53 Error codes (part code 05305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05305 075040 This functionality is not available because Performance Control is not installed. Install the necessary program product. E 05305 076510 The specified port belongs to a resource Log out, and then log back in with access to the group that you do not have permission resource group containing the specified port. to access.
Table 55 Error codes (part code 05310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05310 005068 The value is not set for the overall control. Set the value for the overall control. W 05310 005069 The maximum value is not set for the non-priority WWN. Set the maximum value for the non-priority WWN. W 05310 005107 The specified name is already used. Verify the settings, and then retry the operation. i 05310 005108 The specified name is already used.
Table 55 Error codes (part code 05310) (continued) Part Code Error Number Error Message Recommended Action Severity Level 05310 009328 The settings for the removed ports remain. To clear the settings, check the check box of W "Delete ports if CHA is removed," and then click [Apply]. 05310 009329 Next, the initialization for the settings on Port control will be performed. If you click [OK] on the next window, the settings W on port control will be initialized.
8 Message (part code group 06nnn) This chapter includes the error messages with the part code 06005 to 06810. Part code 06005 Table 56 Error codes (part code 06005) Part Code Error Number Error Message Recommended Action Severity Level 06005 005013 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 06005 005099 An error occurred during SVP processing.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008704 The specified number of remote paths is Verify the remote path status, and then restore the W less than the minimum number of paths paths. due to a communication error between the local storage system and the remote storage system. 06005 008705 The remote paths cannot be deleted due Verify the CHA status of the local storage system.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level systems is in one of the following statuses: • Maximum 4 remote storage systems are already registered in one CU. • Maximum 64 remote storage systems are already registered while System is selected. 06005 008721 The remote path creation was incomplete. Verify the path connections between the local storage system and the remote storage system, and then retry the operation.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008738 The emulation type of the local storage system does not support Continuous Access Synchronous or Continuous Access Synchronous Z The emulation type of the MCU does not support W TrueCopy. If you want to use TrueCopy, please call the Support Center. 06005 008739 The NVS status of the local storage system connected to the host is not active.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level retry the operation. If the volume is connected to a VM system, vary the volume offline from the VM system. 06005 008751 The emulation type of the remote storage Verify the emulation type of the remote storage system does not support Continuous system. Access Synchronous or Continuous Access Synchronous Z. W 06005 008753 An internal error occurred.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008766 Continuous Access Synchronous or Verify the emulation type of the specified Continuous Access Synchronous Z does secondary volume. not support the emulation type of the secondary volume. 06005 008768 The remote storage system is still used by a different remote replication program product.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008791 The primary volume is online to the host. Vary the concerned path offline from the other host, then retry the operation. 06005 008792 The operation cannot be performed Install the Volume Retention function in the remote W because the Volume Retention function storage system, and then retry the operation. was not installed in the specified remote storage system.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008800 The secondary volume is already used in Auto LUN. Verify the status of the secondary volume. W 06005 008801 The secondary volume is reserved, or the remote path or the remote storage system is in a high-load condition. Verify the status of the secondary volume from the W host. If the secondary volume is not reserved, retry the operation.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008831 The specified secondary volume is already used as a reserved volume of Auto LUN. Specify a different volume. W 06005 008832 The specified secondary volume is used Wait for a few minutes, and then retry the by an Auto LUN pair whose status is operation. changing.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008862 Please retry the Delete Pair(Pairsplit-S) operation later. A few minutes later, retry the operation. E 06005 008863 Unknown Error Code. Please call the HP Technical Support. E 06005 008864 An internal error occurred. If this problem persists, please contact HP Technical Support. E 06005 008865 An internal error occurred.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008899 An internal error occurred. If this problem persists, please contact HP Technical Support. E 06005 008900 An error occurred during the port change. If this problem persists, please contact HP Technical Support. E 06005 008901 An error occurred during the port change. If the problem persists despite retrying, please contact HP Technical Support.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 008926 The specified secondary volume cannot Verify the Volume Security setting of the specified W be used because of the Volume Security secondary volume. setting. 06005 008927 The specified primary volume cannot be Verify the Volume Security setting of the specified W used because of the Volume Security primary volume. setting. 06005 008929 Invalid port type.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action 06005 008982 The pair cannot be created because the Specify a different volume. specified primary volume is a command device. W 06005 008983 The pair cannot be created because the Specify a different volume. specified secondary volume is a command device. W 06005 008989 The specified primary volume is a volume used by Compatible FlashCopy or Compatible FlashCopy SE.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level If the Resync Pairs operation cannot be performed, restore the Continuous Access Journal or Continuous Access Journal Z pair first, and then retry the operation. 06005 058322 The Create Pairs operation cannot be Specify a different volume for the secondary performed because the specified volume. secondary volume is a LUSE volume that is set across multiple CLPRs.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 058498 A pair cannot be created because the specified primary volume is being used as a pool volume. Specify another volume. W 06005 058499 A pair cannot be created because the specified secondary volume is being used as a pool volume. Specify another volume. W 06005 058509 A communication time-out error occurred Wait a while, then retry the operation.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Journal or Continuous Access Journal Z.The operation cannot be performed because the Cont Access Journal 3DC & 4x4 Open MF function is not installed on the local storage system. 06005 068023 The specified secondary volume is used Install the Cont Access Journal 3DC & 4x4 Open W as a pair volume of Continuous Access MF function on the remote storage system.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level then replan a combination of volumes for pair creation. 06005 068816 A pair cannot be created because the specified volume is used as a primary volume of Continuous Access Journal. The specified volume is a primary volume of Continuous Access Journal used in the 2DC configuration in which Continuous Access Synchronous is combined. Select a different volume.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 068880 The operation failed, because the specified volume was used for Auto LUN. Select another volume, or release the Auto LUN setting. E 06005 068882 The operation failed, because the quorum disk was inaccessible. If the problem persists despite retrying, please contact HP Technical Support.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action 06005 078128 The operation cannot be performed because the specified volume is in the online data migration process. Specify a volume other than the one in the online W data migration process.
Table 56 Error codes (part code 06005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06005 208523 The remote storage system does not support Multi-Array Virtualization. Verify the microcode version of the remote storage W system. Or, specify an LDEV on which the virtual access mode is disabled. 06005 208524 The Create Pairs operation cannot be performed because no virtual LDEV ID is set on the volume specified as the secondary volume.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 005040 Too many objects are specified. Specify fewer objects, and then retry the operation. W 06505 005511 The program product is not installed. Install the program product. W 06505 006000 An error occurred during SVP processing. Retry the operation. If this problem persists, contact HP Technical Support. E 06505 006001 An error occurred during SVP processing.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008702 The status of the primary volume is invalid. Refresh the window, and then verify the status of the primary volume. Retry the operation if the primary volume is available. W 06505 008703 The specified number of remote paths is Verify the number of remote paths, and then retry W less than the minimum number of paths. the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message 06505 008721 The remote path creation is not complete Verify the remote path connections between the yet. local and the remote storage systems, and then retry the operation. W 06505 008722 The remote path could not be created.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008744 The specified primary volume cannot be Verify that the primary volume is in any of the used. following conditions: W • The volume is in data copy process (correction copy or drive copy). • The volume is in correction access condition. • The volume is blocked. • The volume is being maintained. • The access attribute of the volume is Read Only.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008795 The operation cannot be performed because the volume specified as the primary volume is used by Business Copy or Business Copy Z and applies to either of the following: Verify the status of the primary volume from the host or the SVP. W Verify the status of the volume specified as a secondary volume. W • A secondary volume, which is not in the PSUS status.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008891 LUN paths are defined on the specified port. Delete the LUN paths on the specified port, and then retry the operation. W 06505 008893 An internal error occurred. Verify the SSB log, and then contact HP Technical E Support. 06505 008894 Jobs exist on the specified port. Stop the jobs from the host, and then retry the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 008944 The specified secondary volume cannot Verify the access attribute of the specified be used because of the access attribute secondary volume. changed by Data Retention. W 06505 008947 The external volume that is mapped to an internal volume is connected to the port. Release the setting of the external volume, then retry the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058016 The cache or the shared memory is in an abnormal state. If this problem persists, contact HP Technical Support. E 06505 058017 The specified volume is being connected Check the status of the specified volume from the W by a mainframe host. mainframe host.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action 06505 058036 The device emulation type of the specified volume is not supported. Check the emulation type of the specified volume. W 06505 058037 The specified journal cannot be deleted Verify the status of the specified journal. because a data volume exists. W 06505 058038 No more path group IDs can be registered.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058082 The specified consistency group is already used. Verify the consistency group status on the Continuous Access Journal window of the local and remote storage systems. W 06505 058083 The specified master journal is not registered. Check the status of the specified master journal.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level registered remote storage system, and then enter the correct values. If the specified values are correct, verify the cable connection of the remote storage system. If this problem persists, contact the Hitachi Data Systems Support Center. 06505 058101 The pair status is incorrect. Refresh the window, and then verify the pair status. 06505 058102 An internal error occurred.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level creating Delta resync volume pairs is already used by the ordinary (not Delta resync) volume pairs. 06505 058271 The volume specified as the secondary volume cannot be used due to one of the following reasons: • S-VOL Disable is set by Data Retention.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action 06505 058281 No more pairs can be registered in the specified restore journal. Check the number of pairs in the specified restore W journal. 06505 058282 The specified secondary volume is Verify the journal in which the specified secondary W already registered in a different journal. volume is registered.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058296 The specified volume cannot be used because it is being used by any of the following program products: Release the setting of the different program product that uses the specified volume and then retry the operation, or select a different volume.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message 06505 058334 The parameter related to the inflow Verify the status of the specified journal. cannot be changed, because the status of the specified journal is neither "Initial" nor "Stopped". W 06505 058335 The timer type cannot be changed, because the status of the specified journal is not "Initial".
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action 06505 058348 The Create Pairs operation cannot be performed because VMA of Data Retention is set on the volume specified as the primary volume. Verify the settings of the specified primary volume W from the Data Retention window.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058355 The pair operation cannot be performed Select a different volume, or delete the pair whose W because the volume specified as the volume is used by a different program product, secondary volume is being used by one and then retry the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058487 The Create Pairs operation cannot be Verify the status of the volume specified as the performed because the volume specified primary volume. as the primary volume is a pool volume.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058550 The operation to add journal volumes failed due to the mirror status of the specified journal. Verify the status of the mirrors in the specified journal. W 06505 058552 The operation cannot be performed because the program product license of System Array Management is not installed on the remote storage system.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058593 The storage system has accepted the request normally, however the processing requires some time. Refresh the window. If this message is displayed after: W • the setting operation, verify that the setting is reflected. • the operation of changing pair status, verify the status of the primary and secondary volumes.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058607 Journal groups cannot be deleted from the extended consistency group (EXCTG), because the specified journal group was not registered. Verify the journals in the specified extended consistency group (EXCTG). W 06505 058608 The Resync Pairs operation cannot be performed.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Check if the specified command device exists in the device of specified serial number. W because the attribute of the specified journal is invalid. 06505 058624 Journals cannot be added to the extended consistency group (EXCTG), because the combination of the serial number and the command device is invalid.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 058686 The specified operation failed, because Check the attribute of the journal of the remote the attribute of the journal of the remote storage system. storage system was not "restore". W 06505 058687 The status of the other mirror of the Delta If this problem persists, contact HP Technical resync did not change. Support.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level Verify the status of the mirrors in the specified journal. W an external volume to which the I/O suppression mode is enabled. 06505 058697 The journal volume cannot be deleted from the specified journal due to the mirror status. 06505 058698 The operation cannot be performed Verify the status of the specified secondary because the specified secondary volume volume.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level volume should meet the following conditions: • It is a secondary volume of a different mirror. • It is in PSUS, PSUE, Suspend, PAIR, or Duplex status. 06505 058707 The Create Pairs operation or the Resync Verify the status of the specified secondary Pairs operation cannot be performed volume. because the status of the specified secondary volume is Not Ready.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level of the licensed capacities. The related program products are: • Continuous Access Synchronous or Continuous Access Synchronous Z • Continuous Access Journal or Continuous Access Journal Z 06505 068003 The operation failed, because the specified journal was not registered. Check if the specified journal is registered.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 068019 The remote storage system does not support the LDEV ID of the specified primary volume. Specify the LDEV ID that is supported by the remote storage system, and then retry the operation. W 06505 068024 The operation failed because the current Check the connected storage system's microcode W microcode version does not support version. Delta Resync.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level specified primary volume is either of the suspend the Continuous Access Synchronous pair following. . • The volume is not used by Continuous Access Synchronous. • The volume is used by Continuous Access Synchronous, but the pair status is not PSUS or PSUE.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 068850 The operation cannot be performed because the consistency group of the specified data volume is shared with multiple local and remote storage systems, and LU is specified for Range. Specify "Mirror" for the [Range], then retry the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level and is suspended by either of the following pair settings: • A pair in a synchronous consistency group. • A pair that Cylinder is set for Differential Management. 06505 068888 The operation cannot be performed Confirm the relationship status of the Compatible W because the specified primary volume is FlashCopy.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 068912 The operation cannot be performed Install the program product license of Cont Access W because the program product license of Journal 3DC & 4x4 Open MF on the local storage Cont Access Journal 3DC & 4x4 Open system, and then retry the operation. MF is not installed on the local storage system.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level intermediate sites in the Continuous Access Journal or Continuous Access Journal Z 3DC cascading configuration is Active. 06505 068925 The operation to create a pair for delta Verify the status of the specified primary volume. W resync cannot be performed because the pair status of the specified primary volume is not PAIR.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 078265 A request to create a pair using a Verify the settings. journal in the configuration consisting of three Continuous Access Journal sites was received. However, the operation failed because a pair creation for the Delta resync is specified.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 078276 The Resync Pairs operation cannot be performed because the specified secondary volume is already used as a secondary volume of a pair in a different mirror and the pair status is not applicable to the operation.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message 06505 078301 Failed to change the mirror option Verify the parameter of the specified Copy Pace. W because the parameter of Copy Pace is invalid. 06505 078302 Failed to change the mirror option because the parameter of Path Watch Time is invalid. Verify the parameter of the specified Path Watch W Time. 06505 078303 Failed to change the mirror option because the parameter of Transfer Speed is invalid.
Table 58 Error codes (part code 06505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06505 208536 The Create Pairs operation cannot be Verify the status of the specified secondary performed because the volume specified volume, the virtual serial number, or the virtual as the secondary volume applies to any controller ID.
Part code 06507 Table 59 Error codes (part code 06507) Part Code Error Number Error Message Recommended Action Severity Level 06507 005036 Two or more commands which were not Verify the settings, and then retry the operation. able to be processed were demanded. W 06507 006012 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 06507 006036 An error occurred during SVP processing. If this problem persists, contact HP Technical Support.
Table 60 Error codes (part code 06805) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06805 055009 An invalid CLPR No. was detected. Correct the cache resource number (CLPR No.), then retry the operation. If this problem persists, please call the Support Center. E 06805 055209 The maximum number of CLPRs that can Specify the number of CLPRs within the valid be created was exceeded. range. 06805 055210 The Block Option setting is incorrect.
Table 61 Error codes (part code 06810) (continued) Part Code Error Number Error Message Recommended Action Severity Level 06810 009102 Do you want to apply? To execute the operation in Preview, click [OK]. W 06810 009106 The value that is under setup is not To change the mode, click [OK]. Otherwise, click i reflected yet. Do you want to change the [Cancel]. mode? 06810 009107 The value that is under setup is not reflected yet.
9 Message (part code group 07nnn) This chapter includes the error messages with the part code 07005 to 07105. Part code 07005 Table 62 Error codes (part code 07005) Part Code Error Number Error Message Recommended Action Severity Level 07005 005013 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 07005 005099 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 008503 You cannot create the new pair, because Delete the Remote Copy pair. a remote copy pair exists in the same storage system frame. 07005 008504 The command could not be executed. Verify the composition, the status, or the volume W status of the pair.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008524 The emulation type is not supported. Specify the emulation type supported in HOMRCF. W 07005 008525 An internal logic error occurred. Contact HP Technical Support. E 07005 008526 An internal logic error occurred. Contact HP Technical Support. E 07005 008527 An internal logic error occurred. Contact HP Technical Support.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 008552 This volume cannot be specified as an Check the target volume. P-VOL because it is used as a command device. 07005 008553 The S-VOL is not implemented. 07005 008554 The command could not be executed Restore the blocked volume, or select a volume because the specified secondary volume that is not a system disk, and then retry the is blocked or used as a system disk. operation.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008583 The RAID level of the specified volume is not supported. Specify a volume of the supported RAID level. W 07005 008586 The number of groups that can be set in Verify the settings, and then retry the operation. the same storage system is invalid. W 07005 008587 The number of pairs that can be set in the same group is invalid.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action 07005 008607 The command cannot be run because the specified secondary volume is used as a primary volume of a Continuous Access Synchronous pair. See the Business Copy User Guide for the relation W between the pair status of Continuous Access Synchronous and the Business Copy operations.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 008630 The status mode type is invalid. Verify the settings, and then retry the operation. W 07005 008631 The specified CU number is invalid. Contact HP Technical Support. W 07005 008632 The timing of issuing the command is invalid. Contact HP Technical Support. E 07005 008633 The abnormal status is invalid. Contact HP Technical Support.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 008649 Because the boot device is the S-VOL in Check the specified volume number. the Pairsplit-S (Delete Pairs) command, the flag does not match. W 07005 008650 The boot device and the P-VOL do not match in the Paircreate (Create Pairs), Pairresync (Resync Pairs), or Pairsplit-S (Delete Pairs) command. Check the target volume number. W 07005 008651 The SSID is invalid.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 057101 An error occurred during SVP processing. If this problem persists, contact HP Technical Support. E 07005 057102 An error occurred during SVP processing. If this problem persists, contact HP Technical Support.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action 07005 058300 The operation failed, because the specified S-VOL was a data volume of Continuous Access Journal. Release the Continuous Access Journal setting or W specify another volume. 07005 058351 The Quick Restore command could not be executed because the specified pair contains external volumes, and also is used as a Continuous Access Journal pair.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 058573 This function is not supported. Check if the DKCMAIN and SVP microcode versions are mismatched. E 07005 058574 An error occurred while connecting to the storage system. If this problem persists, contact HP Technical Support. E 07005 058575 An error occurred while connecting to the storage system. If this problem persists, contact HP Technical Support.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level Provisioning volume not associated with a pool. 07005 068743 The command has been rejected, because Quick Format is performed on the specified P-VOL. Retry the operation after quick formatting is complete. W 07005 068744 The command has been rejected, because Quick Format is performed on the specified S-VOL. Retry the operation after quick formatting is complete.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 068838 The command has been rejected, Wait until the zero page reclamation is because the specified S-VOL is a volume completed, and then retry the operation. of Thin Provisioning whose zero page is being reclaimed. W 07005 068867 The command has been rejected, because the volume specified as P-VOL is a quorum disk. Specify another volume.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level as S-VOL was not associated with a pool. 07005 075005 The command could not be executed because no LUN path is set to the volume specified as a primary volume. 07005 075006 The command could not be executed Set an LUN path to the specified secondary because no LUN path is set to the volume, and then retry the operation. volume specified as a secondary volume.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078142 The operation cannot be done because Release the Fast Snap pair setting or specify the specified secondary volume is a another volume. secondary volume of Fast Snap. W 07005 078143 The specified snapshot number is used in another pair of Fast Snap.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078153 The LDEV number that is specified as a primary volume is invalid. Specify another LDEV number. W 07005 078154 The command was rejected because the Specify a volume of supported emulation type. emulation type of the specified primary volume was not OPEN-V.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 078167 The command was rejected because the Verify the Max LBA size of the volume. Max LBA size of the specified primary and the secondary volumes was different. W 07005 078168 The command was rejected because the Verify the number of slots of the volume. number of slots is different between the specified primary and the secondary volumes.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078182 The command was rejected because the Change the status of the Business Copy pair to primary volume of Fast Snap and the PSUS, and then retry the operation. secondary volume of Business Copy share a volume, and the pair of Business Copy was not in the state of PSUS.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078195 The command was rejected because the Select a volume other than the external volume primary volume is used as an external mapped for the online data migration, and then volume that is mapped for online data retry the operation. migration.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message 07005 078258 The operation failed because the volume Verify the status of the volume. specified as the S-VOL is a leaf volume. 07005 078259 The operation failed because the specified P-VOL that uses two mirrors in 3DC cascade, 3DC multi target, or Delta resync configuration is in one of the following statuses. • The volume is in the Continuous Access Journal Delta resync configuration.
Table 62 Error codes (part code 07005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07005 078310 The Fast Snap pair operation cannot be Change the status of pairs related to the specified W performed because all Fast Snap pairs primary volume to enable the pair operation, and that share the specified primary volume then retry the operation. are in PSUE status.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 005626 The specified volume cannot be used because it is write-protected by Volume Retention. Release the write-protection by Volume Retention. W 07105 006502 Processing in progress. Wait for a while, and then retry the operation. W 07105 006503 The volume status is being changed to simplex. Wait for a while, and then retry the operation.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008512 Cannot perform Resync or Suspend operation because of the path group setting. Detach the S-VOL(Primary Volume) from the host, W or delete the Remote Copy path. 07105 008513 The command has been rejected, because the specified S-VOL(Primary Volume) is used by the host.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message 07105 008540 There is sufficient shared memory to Contact HP Technical Support. create 4096 pairs, but initial storage system setup is required before creating pairs. E 07105 008541 There is sufficient shared memory to create 4096 pairs, and the initial storage system setup is complete. Close the message box. i 07105 008542 Failed to complete the initial shared memory setup. Contact HP Technical Support.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008562 The command code sender is invalid. If this problem persists, contact HP Technical Support. E 07105 008563 The volume type is invalid. Contact HP Technical Support. W 07105 008564 The volume type is invalid. Contact HP Technical Support. W 07105 008565 The command code sender is invalid. Verify the settings, and then retry the operation.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action 07105 008595 The specified S-VOL(Primary Volume) does not exist. Refresh the window, and then retry the operation. W 07105 008597 No more pairs can be created for the specified S-VOL(Primary Volume). Pairs cannot be created with the specified S-VOL W any more. See the Business Copy for Mainframe Systems User Guide for the configuration of pairs.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008614 The T-VOL(Secondary Volume) is used as a Remote Copy M-VOL. The requested operation cannot be performed in W the current pair status of Continuous Access Synchronous Z.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008640 The command has been rejected, because the pair sharing the S-VOL(Primary Volume) was in the Reverse Copy or Quick Restore status. Wait until Reverse Copy or Quick Restore completes. W 07105 008641 The pairs contain a pair in the Reverse Copy status. The specified operation cannot be performed.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008655 An invalid secondary SSID is specified Verify the settings, and then retry the operation. for the Add Pair(Create Pairs) or Resync Pairs command. W 07105 008656 An invalid secondary SSID is specified for the Delete Pairs or Split Pairs command. Verify the settings, and then retry the operation.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 008996 The command has been rejected, because the storage system is busy. Wait for a while, and then retry the operation. W 07105 055645 Quick Restore cannot be performed Use the Reverse Resync option. because the specified pair is composed of the external volumes with different cache mode settings.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level between Continuous Access Synchronous Z pair status and Business Copy Z operations. 07105 058262 A pair cannot be created because shared memory for differential tables is insufficient. Please add sufficient shared memory to create a pair.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 058585 The operation failed because the CU group of the specified volume is not supported. Volumes that do not belong to CU group 0 are W currently not supported. Specify another volume. 07105 058630 The operation failed because the specified primary volume is used by Delta resync of Continuous Access Journal Z.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 068767 The SI Operation for FICON(R) Data Migration failed because the specified pair consists of either a primary volume other than a FICON(R) Data Migration source volume or a secondary volume that is a FICON(R) Data Migration source volume. The SI Operation for FICON(R) Data Migration W cannot be performed in the current pair configuration.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level 07105 068809 The command was rejected because the specified T-VOL(Secondary Volume) was a Thin Provisioning Z volume whose capacity was being added. The operation cannot be done because the capacity of target volume changes. Verify the capacity of the volume, and then retry the operation.
Table 64 Error codes (part code 07105) (continued) Part Code Error Number Error Message Recommended Action Severity Level as T-VOL(Secondary Volume) was not associated with a pool. 07105 075015 The specified LDEV belongs to a resource group that you do not have permission to access. Log out, and then log back in with access to the resource group containing the specified LDEV. W 07105 078069 The operation failed because the emulation type of the specified S-VOL(Primary Volume) was 3390-V.
10 Message (part code group 08nnn) This chapter includes the error messages with the part code 08005 to 08905. Part code 08005 Table 65 Error codes (part code 08005) Part Code Error Number Error Message Recommended Action Severity Level 08005 002002 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08005 002015 A connection error has occurred. If the problem persists despite retrying, please contact HP Technical Support.
Table 65 Error codes (part code 08005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08005 008100 An error occurred while connecting to the storage system. Wait, then retry the operation. If the same problem persists despite retrying, please contact HP Technical Support. E 08005 056301 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support.
Part code 08107 Table 66 Error codes (part code 08107) Part Code Error Number Error Message Recommended Action Severity Level 08107 005641 The number of lines exceeds the maximum number of lines of a spreadsheet. If the problem persists despite retrying, please contact HP Technical Support. E 08107 005642 The number of characters exceeds the maximum number of characters of a spreadsheet. If the problem persists despite retrying, please contact HP Technical Support.
Table 68 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08505 007110 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08505 008001 A communication time-out error occurred. If this problem persists, contact HP Technical Support. W 08505 008002 An error occurred during SVP processing. If this problem persists, contact HP Technical Support.
Table 68 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08505 055023 An attempt has been made to either register newly a SLPR that is already registered, or delete a SLPR that is not registered. If the problem persists despite retrying, please contact HP Technical Support. E 08505 055024 The configuration of the CLPR is already Select a different parity group, and then retry the W changed, or some parity groups or some operation.
Table 68 Error codes (part code 08505) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08505 058310 Some of the shared memories of the storage system may be blocked, or the storage system is being maintained. Verify the status of the storage system. If this problem persists, contact HP Technical Support. W 08505 058311 Some of the cache memories of the storage system may be blocked, or the storage system is being maintained.
Part code 08507 Table 69 Error codes (part code 08507) Part Code Error Number Error Message Recommended Action Severity Level 08507 006012 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 08507 007070 An error occurred during SVP processing. If the same problem persists despite retrying, please call HP Technical Support. E 08507 007071 An error occurred during SVP processing.
Table 71 Error codes (part code 08522) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08522 105018 No parity groups or virtual volumes are Select one or more table rows. selected in the Available Parity Groups or Available Virtual Volumes table. W 08522 105019 No CLPR is selected. Select one table row. W 08522 105020 CLPR names cannot be assigned to all of the selected CLPRs with the specified value of Initial Number.
Table 72 Error codes (part code 08605) (continued) Part Code Error Number Error Message Recommended Action 08605 065753 Invalid character is included in the e-mail Delete the characters that cannot be used. addresses or the server addresses. W 08605 065754 The number of characters specified in an e-mail address or a server address exceeds 255 characters. W 08605 065755 An attribute of the registered destination Check the setting(s). of messages is invalid.
Table 74 Error codes (part code 08622) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08622 205039 The form of Password is wrong. Check the settings. W 08622 209002 A test e-mail was sent. Wait for a while, and then verify the result. i Part code 08805 Table 75 Error codes (part code 08805) Part Code Error Number Error Message Recommended Action Severity Level 08805 005010 An error occurred during SVP processing.
Table 76 Error codes (part code 08905) (continued) Part Code Error Number Error Message Recommended Action Severity Level 08905 006023 An inconsistency may have occurred in the syslog setting. If this problem persists, contact HP Technical Support. E 08905 056524 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 08905 076518 Failed to send the test message. If this problem persists, please contact HP Technical Support.
11 Message (part code group 09nnn) This chapter includes the error messages with the part code 09005 to 09610. Part code 09005 Table 77 Error codes (part code 09005) Part Code Error Number Error Message Recommended Action Severity Level 09005 005013 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 09005 005040 The number of requests exceeds the maximum number that can be processed.
Table 77 Error codes (part code 09005) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09005 008100 An error occurred while connecting to the storage system. If the problem persists despite retrying, please contact HP Technical Support. E 09005 008102 This function is not supported. Check the DKC-MAIN version. E 09005 008103 The storage system status is invalid. Retry the operation. If this problem persists, contact HP Technical Support.
Part code 09205 Table 80 Error codes (part code 09205) Part Code Error Number Error Message Recommended Action Severity Level 09205 005013 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 09205 005030 No commands are issued. If the problem persists despite retrying, please contact HP Technical Support. W 09205 005041 The number of issued commands exceeds the maximum. Reduce the number of set demands.
Table 80 Error codes (part code 09205) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09205 008126 This logical volume is configured as a command device. Verify the logical volume, and then retry the operation. W 09205 008136 The command was rejected, because the licensed capacity was exceeded. The currently licensed capacity is insufficient. To W increase the licensed capacity, buy a new license key.
Table 80 Error codes (part code 09205) (continued) Part Code Error Number Error Message Recommended Action Severity Level (The combination of a CU number and an LDEV number is repeated.) 09205 066013 The access attribute set in the [Attribute] Enter a correct attribute in the [Attribute] of the of the spreadsheet is incorrect spreadsheet (enter Read/Write, Read Only, or Protect). (an attribute other than Read/Write, W Read Only, or Protect is entered).
Table 82 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action 09605 006023 An error occurred during array controller If the problem persists despite retrying, please processing. contact HP Technical Support. Severity Level E If this problem persists, please contact HP Technical Support. 09605 006038 The mistake is found in the set parameter. If the problem persists despite retrying, please contact HP Technical Support.
Table 82 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09605 008135 The specified volume is a Continuous Access Synchronous secondary volume in COPY or PAIR status or a Business Copy secondary volume in COPY, PAIR, COPY (SP), COPY (RS), or COPY (RS-R) status. If the pair is Continuous Access Synchronous, change the status to PSUS, and then retry the operation.
Table 82 Error codes (part code 09605) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09605 058422 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 09605 058423 An error occurred during SVP processing. If the problem persists despite retrying, please contact HP Technical Support. E 09605 058424 The specified logical volume is blocked.
Table 83 Error codes (part code 09610) (continued) Part Code Error Number Error Message Recommended Action Severity Level 09610 009107 The value that is under setup is not reflected yet. Do you want to continue the operation? To continue processing, click [OK]. To stop processing, click [Cancel]. W 09610 009362 Do you want to change the expiration lock mode? To change the mode, click [OK]. Otherwise, click i [Cancel].
12 Message (part code group 10nnn) This chapter includes the error messages with the part code 10021 to 10126. Part code 10021 Table 84 Error codes (part code 10021) Part Code Error Number Error Message Recommended Action Severity Level 10021 209018 Are you sure you want to transfer the Audit Log to the Primary Server based on the applied information? To continue, click [OK]. Otherwise, click [Cancel]. i 10021 209019 Are you sure you want to transfer the To continue, click [OK].
Part code 10122 Table 87 Error codes (part code 10122) Part Code Error Number Error Message Recommended Action Severity Level 10122 105194 An error occurred while formatting. Retry the operation. If this problem persists, contact HP Technical Support. E 10122 105195 An error occurred while preparing the quick format. Retry the operation. If this problem persists, contact HP Technical Support. E 10122 105196 The specified encryption key cannot be deleted because it is not created.
Table 87 Error codes (part code 10122) (continued) Part Code Error Number Error Message Recommended Action 10122 105482 You have not agreed to the notice for the key generation protection. Read the notice for the key generation protection, W and then check the "I agree" check box if you agree. 10122 105490 The setting of the key management server is changed. Perform Rekey Key Encryption Key after the task is complete. W 10122 105491 The key encryption key cannot be registered.
Table 87 Error codes (part code 10122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10122 107001 An internal logic error occurred. If this problem persists, contact HP Technical Support. E 10122 107002 An internal logic error occurred. If this problem persists, contact HP Technical Support. E 10122 109029 Be sure to back up after the task is complete. Click [OK].
Table 88 Error codes (part code 10126) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10126 105009 The specified encryption key was not found in the key management server. Verify the specified encryption key. E 10126 105010 Failed to delete the specified encryption The following message is returned from the server. E key from the key management server.
Table 88 Error codes (part code 10126) (continued) Part Code Error Number Error Message Recommended Action Severity Level 10126 105017 The "Setup Key Management Server" is Configure the "Setup Key Management Server". not configured. E 10126 105018 The "Setup Key Management Server" is Configure the "Setup Key Management Server". not configured. E 10126 105019 The "Setup Key Management Server" is Configure the "Setup Key Management Server". not configured.
13 Message (part code group 20nnn) This chapter includes the error messages with the part code 20020 to 20922. Part code 20020 Table 89 Error codes (part code 20020) Part Code Error Number Error Message Recommended Action Severity Level 20020 107000 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support. E 20020 107001 An error occurred during SVP processing. If this problem persists, please contact HP Technical Support.
Table 89 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107021 A file or a directory of the specified path Check the environment of file or directory of the does not exist, or the access is rejected. specified path. E 20020 107022 The same path is specified in the output Set a different path. source and the output target.
Table 89 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107043 Failed to save the specific information of user. Check the environment. E 20020 107044 Failed to save the specific information of user. Check the environment. E 20020 107045 Failed to save the specific information of user. Check the environment. E 20020 107046 A network error occurred. The causes might be one of the following.
Table 89 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107063 Failed to access the key store file. Check the environment. E 20020 107064 Failed to get a certificate. Check the environment. E 20020 107065 The key store file does not exist. Check the environment. E 20020 107066 Failed to read the key store file. Check the environment. E 20020 107067 The specified alias does not exist. Check the environment.
Table 89 Error codes (part code 20020) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20020 107098 The user information of the specified onetime key does not exist. Check the environment. E 20020 107099 Failed to get the user information from the specified onetime key. Check the environment. E 20020 107100 The user information of the specified global session ID does not exist. Check the environment.
Table 90 Error codes (part code 20121) (continued) Part Code Error Number Error Message Recommended Action Severity Level If this problem persists, contact HP Technical Support. 20121 107090 An internal logic error occurred. If the same problem persists despite retrying, please contact HP Technical Support. E 20121 107091 An I/O error occurred during downloading. If the same problem persists despite retrying, please contact HP Technical Support.
Part code 20122 Table 91 Error codes (part code 20122) Part Code Error Number Error Message Recommended Action Severity Level 20122 105054 The task cannot be changed to the specified status. If the problem persists despite retrying, please contact HP Technical Support. W 20122 105055 The number of registered tasks has reached the maximum. Wait for a while, then retry the operation.
Table 91 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20122 106056 An error occurred. Check the details of the error from the following error code list. E 20122 106057 An error occurred. Check the details of the error from the following error code list. E 20122 106058 An error occurred. Check the details of the error from the following error code list. E 20122 106059 An error occurred.
Table 91 Error codes (part code 20122) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20122 108031 There is a license that xxx day(s) remain Check the expiration date or the license capacity W of the program products on the license key to end, or a license whose capacity is window. Purchase new licenses if you want to insufficient. continue to use those program products.
Part code 20123 Table 92 Error codes (part code 20123) Part Code Error Number Error Message Recommended Action Severity Level 20123 107000 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 107001 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 107002 An internal logic error occurred.
Table 92 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action 20123 107016 A network error occurred. It is not Verify the IP address. If the IP address is correct, possible to connect with the SVP due to close the browser (also close the storage list one of the following reasons. browser), and then log on again. Severity Level E • The SVP was not ready. • An error occurred in the SVP. 20123 107017 An error occurred during SVP processing.
Table 92 Error codes (part code 20123) (continued) Part Code Error Number Error Message Recommended Action Severity Level If this problem still persists, contact HP Technical Support. 20123 108000 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 108001 An internal logic error occurred. If the problem persists despite retrying, please contact HP Technical Support. E 20123 108002 An internal logic error occurred.
Table 93 Error codes (part code 20222) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20222 109005 The task (xxx) is in progress. - i 20222 109006 The task (xxx) is complete. - i 20222 109007 An error occurred during the task (xxx) processing. E 20222 109008 An error occurred during the task (xxx) processing. E Verify the details of the error with the error code in the following list. 20222 109009 The task (xxx) is aborted.
Table 94 Error codes (part code 20305) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20305 008001 A communication time-out error occurred. If the same problem persists despite retrying, please contact HP Technical Support. E 20305 008100 An error occurred while connecting to the storage system. If the same problem persists despite retrying, please contact HP Technical Support. E 20305 076500 The specified MP Blade is not mounted.
Table 96 Error codes (part code 20422) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20422 106076 The specified monitoring period cannot be set. Set the interval between the start and finish time to more than one hour, then retry the operation. W 20422 106077 Four or more drive types cannot be added to the specified pool. Check the support configuration of pools, then retry the operation.
Table 97 Error codes (part code 20520) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20520 107018 Failed to create a report. Check the environment. E 20520 107019 Failed to create a report. Check the environment. E 20520 107100 Succeeded to create a report file. Click [OK]. i 20520 107107 Failed to create a report file. Check the environment. W 20520 109001 Succeeded to create a report. Click [OK].
Table 99 Error codes (part code 20525) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20525 107007 The current microcode version does not support the specified command. Verify the current SVP microcode version. W 20525 107008 The specified function is not available Install the necessary program product. because the necessary program product is not installed. W 20525 107009 You do not have permission to perform operations on the specified resources.
Table 100 Error codes (part code 20624) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20624 107003 An internal logic error occurred. If this problem persists, please contact HP Technical Support. E 20624 107004 An error occurred while connecting to the session control server. Verify the status of the session control server, and E then retry. 20624 107005 An internal logic error occurred.
Table 101 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action 20705 076101 The number of requests exceeds the maximum number that can be processed. Reduce the number of requests, and then retry the E operation. 20705 076102 An incorrect ResourceGroupID was specified. Specify the registered ResourceGroupID, and then W retry the operation. 20705 076103 The specified ResourceGroupID has already been specified.
Table 101 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 076123 Migration of resources that belong to different resource groups cannot be done. A part of specified resources might be migrated. W Verify the configuration of the resource group to which the resources belong, and then retry the operation to migrate the resources that belong to one resource group.
Table 101 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level the resource group whose virtual mode is set to ON. 20705 077114 The specified resource is already used. Release the duplicated settings, and then retry the W operation. 20705 077115 The value of SSID is not set within the available range. Check the value of the specified SSID. W 20705 077116 The specified Virtual Storage Machine does not exist. Verify the settings.
Table 101 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 077131 The operation cannot be performed because the specified LDEV is used by a High Availability pair. Delete the High Availability pair, and then retry the operation. W 20705 077132 The operation cannot be performed because the specified LDEV is used by an Auto LUN pair. Delete the Auto LUN pair, and then retry the operation.
Table 101 Error codes (part code 20705) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20705 077151 The operation cannot be performed because the specified LDEV is used as a journal volume. Release the journal volume setting, and then retry W the operation. 20705 077152 The specified serial number or the controller ID is invalid. Verify the settings.
Table 103 Error codes (part code 20722) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20722 105294 Resources cannot be deleted from meta_resource. Specify another resource group. W 20722 105295 An error occurred during the resource addition. Although the resource group was created, the resource was not added. Perform the resource addition. W 20722 105303 The specified resource group does not exist in the configuration. Execute refresh.
Table 103 Error codes (part code 20722) (continued) Part Code Error Number Error Message Recommended Action Severity Level a different virtual storage machine, and then retry the operation. 20722 205063 The selected LDEV cannot be deleted because it belongs to a virtual storage machine other than that of meta_resource and a virtual LDEV ID is defined to it. Release the definition of the virtual LDEV ID of the W selected LDEV, and then retry the operation.
Part code 20921 Table 105 Error codes (part code 20921) Part Code Error Number Error Message Recommended Action Severity Level 20921 105001 No table rows are selected. Select one or more table rows. W 20921 105009 The name of the new snapshot group is Enter a different snapshot group, or select one identical to one of the existing snapshot from the snapshot groups that are already groups. defined. 20921 109211 The CLPRs of the primary and secondary To continue, click [OK].
Table 106 Error codes (part code 20922) (continued) Part Code Error Number Error Message 20922 105490 When a pair volume is set as a Select one each from the Available LDEVs table W secondary volume, multiple rows cannot and the Selected Pairs table, and then click [Set]. be set at the same time. 20922 106113 The operation cannot be done because Verify if there is any volume that can be used to there is no volume available for pair create a pair or not. creation.
Table 106 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 106133 The selected pair cannot be edited Verify the setting contents of the selected pair. because the L2 pair is already set to the selected pair. W 20922 106134 The selected pair cannot be edited Verify the setting of the selected pair. because the Mirror Unit is already fixed.
Table 106 Error codes (part code 20922) (continued) Part Code Error Number Error Message 20922 106158 The operation cannot be done because Verify the status of the selected pair, and then W the status of a pair within the selected retry. If this problem persists, refresh the window, pairs and in a cascade configuration is and then retry. incorrect.
Table 106 Error codes (part code 20922) (continued) Part Code Error Number Error Message Recommended Action Severity Level 20922 205021 The operation cannot be performed because the selected pairs include FICON(R) Data Migration and the others. Verify the selected pairs, and then retry the operation. W 20922 205022 The Window cannot be displayed Refresh the window, and then retry the operation.
14 Message (part code group 21nnn) This chapter includes the error messages with the part code 21021 to 21122. Part code 21021 Table 107 Error codes (part code 21021) Part Code Error Number Error Message Recommended Action Severity Level 21021 105001 No table rows are selected. Select one or more table rows. W 21021 105003 No table row, or two or more table rows Select one table row. are selected. W 21021 105007 No table row is selected. Select one table row.
Part code 21022 Table 108 Error codes (part code 21022) Part Code Error Number Error Message Recommended Action Severity Level 21022 107001 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation. E If this problem persists, contact HP Technical Support. 21022 107002 The processing cannot continue due to an internal logic contradiction. Refresh the window, and then retry the operation.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message 21022 206009 The operation cannot be performed Verify the copy type of the selected pair, and then W because the selected pairs have different retry the operation. copy types. 21022 206010 The operation cannot be performed because the selected mirrors have different journal types. Verify the journal type of the selected mirror, and W then retry the operation.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 21022 206026 No more pairs can be created because Verify the device configuration of the storage the number of created pairs has reached system. the maximum. W 21022 206027 No more pairs can be created because Change the master journal, or verify the number the number of created pairs has reached of pairs in the specified journal. the maximum in the selected journal.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action 21022 206048 Journals cannot be created because there is no free journal ID. Remove unnecessary journals, and then retry the W operation. 21022 206049 Volumes cannot be added to or removed Verify the journal status. from the selected journal.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 21022 206064 No remote command device is assigned Verify the selected mirror, and then retry the to the selected mirror. operation. W 21022 206065 No more pairs can be created because Verify the device configuration of the storage the number of created pairs has reached system. the maximum. W 21022 206066 The update of the history information is not completed.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 21022 206083 The operation cannot be performed because the attribute of the selected journal is "initial". Verify the attribute of the selected journal, and then retry the operation. W 21022 206084 Remote command devices are already assigned to two mirrors in the selected journal. Remove the remote command devices, and then retry the operation.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 21022 206126 The selected journals contain journals that do not belong to the extended consistency group. Select journals that belong to the extended consistency group. W 21022 206127 The operation cannot be performed Verify the available attribute, select an extended because the attribute of the selected consistency group, and then retry the operation.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message 21022 206141 No more journals can be added to the Reduce the number of journals to be added, and W extended consistency group because the then retry the operation. number of journals exceeds the maximum. 21022 206142 No more remote paths can be removed Add remote paths, and then retry the operation.
Table 108 Error codes (part code 21022) (continued) Part Code Error Number Error Message Recommended Action Severity Level 21022 206502 The specified pair does not exist in the configuration. Refresh the window, and then retry the operation. W If this problem persists, contact HP Technical Support. 21022 206503 The specified mirror does not exist in the Refresh the window, and then retry the operation. W configuration. If this problem persists, contact HP Technical Support.
15 Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
HP websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/service_locator • http://www.hp.com/support/manuals • http://www.hp.com/support/downloads • http://www.hp.
Table 110 Document conventions (continued) Convention Element Monospace text • File and directory names • System output • Code • Commands, their arguments, and argument values Monospace, italic text • Code variables • Command variables Monospace, bold text WARNING! CAUTION: IMPORTANT: NOTE: TIP: 310 Emphasized monospace text Indicates that failure to follow directions could result in bodily harm or death. Indicates that failure to follow directions could result in damage to equipment or data.
Glossary allocation The ratio of allocated storage capacity versus total capacity as a percentage. Allocated storage refers to those logical devices (LDEVs) that have paths assigned to them. Allocated storage capacity is the sum of the storage of these LDEVs. Total capacity is the sum of the capacity of all LDEVs on the disk array. BC P9000 or XP Business Copy. An HP application that provides volume-level, point-in-time copies in the disk array.
to be associated with 1 to 36 LDEVs. Essentially, LUSE makes it possible for applications to access a single large pool of storage. M-VOL Main volume. MCU Main control unit. OPEN-x A general term describing any of the supported OPEN emulation modes (for example, OPEN-E). There are two types of OPEN-x devices: legacy OPEN-x devices with a fixed size (such as OPEN-3, OPEN-8, OPEN-9, and OPEN-E), and OPEN-V, which has a variable size and is a CVS-based volume.
Index C contacting HP, 308 conventions document, 309 storage capacity values, 309 text symbols, 310 D document conventions, 309 related information, 308 documentation HP website, 308 providing feedback, 308 H help obtaining, 308 HP subscription service, 308 technical support, 308 R related documentation, 308 S storage capacity values conventions, 309 subscription service, HP, 308 symbols in text, 310 T technical support HP, 308 service locator website, 309 text symbols, 310 typographic conventions, 309
