HP XP P9000 Audit Log User and Reference Guide

ManualsBrandsHP ManualsComputer AccessoriesHP P9500 Upgrade DKU Disk Unit Rack

Table Of Contents

HP XP P9000 Audit Log User and Reference

Guide

Abstract

This guide describes the system logs generated by HP XP P9000 Remote Web Console and SVP operations. Topics include

how to view and redirect log output. The intended audience is a storage administrator or authorized service provider with

independent knowledge of HP XP P9000 disk arrays and HP XP P9000 software.

HP Part Number: AV400-96624

Published: March 2014

Edition: Eleventh

Summary of content (279 pages)

PAGE 1
HP XP P9000 Audit Log User and Reference Guide Abstract This guide describes the system logs generated by HP XP P9000 Remote Web Console and SVP operations. Topics include how to view and redirect log output. The intended audience is a storage administrator or authorized service provider with independent knowledge of HP XP P9000 disk arrays and HP XP P9000 software.
PAGE 2
© Copyright 2010, 2014 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
PAGE 3
Contents 1 Introduction.............................................................................................12 Resources that can be executed for each function........................................................................12 Overview..............................................................................................................................12 Features............................................................................................................................
PAGE 4
[BASE] Create Conf Report..................................................................................................55 [BASE] Delete CVAE Info.....................................................................................................55 [BASE] Delete Reports.........................................................................................................56 [BASE] Delete Tasks...........................................................................................................
PAGE 5
[Install] Delete LU Path........................................................................................................78 [Install] Delete WWN.........................................................................................................78 [Install] Dku Emulation........................................................................................................79 [Install] FlashDrive ORM Value.............................................................................................
PAGE 6
[Maintenance] PCB Restore...............................................................................................114 [Maintenance] Pre QuickFormat Stop.................................................................................114 [Maintenance] Quick Format.............................................................................................115 [Maintenance] Replace.....................................................................................................
PAGE 7
[PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] [PROV] Delete Resource Grps............................................................................................
PAGE 8
[PROV] Set PageTieringLevel..............................................................................................165 [PROV] Set Security Switch................................................................................................166 [PROV] Set SSID..............................................................................................................166 [PROV] Set UserAuth........................................................................................................
PAGE 9
[Perf Ctl] PFCGrp Del/Chg................................................................................................187 [Perf Ctl] Update Port WWN.............................................................................................188 [Perf Ctl] Update PFCGrp..................................................................................................188 [Perf Ctl] Update WWN...................................................................................................
PAGE 10
[Ext Stor] Add External Volumes.........................................................................................217 [Ext Stor] Assign MP Blade................................................................................................219 [Ext Stor] Delete ES VOLs..................................................................................................219 [Ext Stor] Disconnect ES Paths............................................................................................
PAGE 11
[ENC] Restore Keys fr Serv.....................................................................................................242 [ENC] Set keys to DKC..........................................................................................................242 [ENC] Setup Key Mng Serv....................................................................................................242 7 Audit log examples for single sign-on........................................................
PAGE 12
1 Introduction Unless otherwise specified, the term P9000 in this guide refers to the following disk array: • P9500 Disk Array The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser. Actual windows may differ depending on the operating system and browser used. GUI contents also vary with licensed program products, storage system models, and firmware versions. Audit logs are created on the Service Processor (SVP) computer in the storage system.
PAGE 13
There are two types of audit log files: • • Audit log file, which consists of two files: ◦ Auditlog information file 1 contains operations performed from the Remote Web Console computer or SVP. ◦ Auditlog information file 2 contains commands sent from a host or a computer using RAID Manager. You can download them to your Remote Web Console computer or transfer to a primary or secondary FTP server Syslog file. This file contains the audit log.
PAGE 14
Table 1 Audit Log File Components (continued) Component Audit Log File Syslog File option. This includes an index representing each item and its values. Maximum Line Size 1,024 bytes 1,024 bytes Maximum Number 250,000 of Lines 250,000 Maximum Size of Files 122.5 MB 488.2 MB When Reaching the Maximum Number of Lines The newest data overwrites the oldest data (wrap around). The newest data overwrites the oldest data (wrap around).
PAGE 15
Figure 2 Audit Log File 2 (DKC) Basic Information Table 2 Basic Information in Audit Log File No. Item File 1 (SVP) File 2 (DKC) 1 Version XXYY indicates the model name (XX) and Same as File 1 the version number in audit log output format (YY). When the output format is changed, the value of YY is updated. See Table 4 (page 18) for the changed contents of XXYY. 2 Date YYYYMMDD indicates the year, month, and day the audit log was created.
PAGE 16
Table 2 Basic Information in Audit Log File (continued) No. Item File 1 (SVP) File 2 (DKC) 5 Interface • RMI AP indicates the log for Remote Web Console and Remote Method Invocation Applications such as HCS. • In-band OPEN indicates open-system hosts. • SVP indicates the log for the SVP. • In-band MF indicates mainframe system hosts. • Out-of-band indicates hosts through the SVP. • RM AP indicates the log for Remote Maintenance Application.
PAGE 17
Table 2 Basic Information in Audit Log File (continued) No. Item File 1 (SVP) File 2 (DKC) message ID of four, five, or six digits. For more information about error codes, see the HP XP P9000 Remote Web Console Messages. NOTE: Error codes "xxxx-yyyyy" appear only for Remote Web Console operations. 13 Host Identification An IP address (IPv4 or IPv6) is output for • A host name is output for commands from Remote Web Console, RMI AP and SVP hosts through the SVP. operations.
PAGE 18
Table 3 Symbols Used in Detailed Parameter in Audit Log (SVP) (continued) Symbol Definition [] When there is more than one setting value for an index, the setting values are enclosed by [ ], and separated by a comma (,). Example: CU:LDEV=[0x00:0x00,0x00:0x01,0x00:0x02] {} Details are enclosed by {}. Example: {Port,Fabric,Connection}=[{1E,ON,FC-AL},{3E,OFF,P-to-P}] () Supplementary and additional information for setting values are enclosed by ( ).
PAGE 19
Table 4 Changed contents of a format in each version number (continued) Version number Changed contents 0705 The output format for DKCMAIN program version 70-02-7x-xx/xx or later, where xx is a two-digit number. The following format is changed from version number 0704. There are no changes to other log formats. • Output format of the detailed information for [PROV] Create LDEVs. 0706 The output format for DKCMAIN program version 70-03-0x-xx/xx or later, where xx is a two-digit number.
PAGE 20
Figure 3 Syslog File Table 5 Items in the Syslog File No. Item Description 1 Priority The priority of an item in the syslog file is determined according to the following formula, enclosed by brackets (< >): Priority = 8 X Facility + Severity Facility is 1 (fixed). Severity depends on the type of log information: • 4: Error or Warning. Error means the operation has ended abnormally. Warning means the operation has partly ended abnormally or was canceled during the operation. • 6: Informational.
PAGE 21
Table 5 Items in the Syslog File (continued) No. Item Description 7 Message identification The serial number of the syslog header information. 8 9 No output Date, time#2* The date, time and the time difference between UTC in the format of "YYYY-MM-DD-Thh:mm:ss.s ± hh:mm." • YYYY: year, MM: month, DD: day. • hh: hour, mm: minute, ss.s: second in one decimal place. • ± hh:mm: hours and minute of the time difference.
PAGE 22
Table 5 Items in the Syslog File (continued) No. Item Description 21 Detailed information Identification of the host sending the request. 22 No output. 23 No output. 24 No output. 25 Collective operation identification number. This is a serial number that identifies that multiple lines displayed by one operation are the same operation. No output when the category name is "AnomalyEvent.
PAGE 23
2 Using audit logs You can download audit log files and syslog files to the Remote Web Console computer or transfer audit log files to FTP servers or syslog servers. Downloading audit log files Download the audit log files to the Remote Web Console computer to prevent the old data from being overwritten. Prerequisites WARNING! Do not download the audit log file to the Remote Web Console computer if the audit log is set to be transferred to an FTP server.
PAGE 24
4. Click Close to close the Audit Log Properties dialog box. NOTE: Audit Log (DKC) is first accumulated in the system disk before it is transferred to SVP. Therefore, it might take time to transfer it to SVP. When there it appears that no logs have been received from a host or a computer using RAID Manager, wait for a while, then retry the download. Downloading syslog files Download syslog files to Remote Web Console computer to prevent the old data from being overwritten.
PAGE 25
4. 5. Click to change to Modify mode. Perform the following if using a primary FTP server. 1. Select Enable in Output to Primary Server. 2. Enter the IP Address in the Primary Server Setting. Do not enter the periods. 3. Enter the User ID and the Password you use to login the primary FTP server. 4. Enter the output folder to which the audit log file will be sent. Specify a relative directory from the home directory as that folder. 6. Perform the following if using a secondary FTP server. 1.
PAGE 26
the syslog server. See RFC3164 (Request For Comment) issued by the IETF (Internet Engineering Task Force) for details of syslog. • You must have Audit Log Administrator (View & Modify) permission to configure syslog server settings. • Keep a list of the items you entered in the window, such as the IP address. You may need to enter them again when an SVP is replaced. To transfer audit log files: 1. 2. 3. Make sure the storage system is connected to syslog servers on a LAN.
PAGE 27
If the log is not received by the syslog server, check whether the IP address and the port number set matches with the IP address and the port number of the syslog server. If the IP address and the port number match, check the syslog server setting. See the user’s manual of the syslog server for the details of the syslog server setting. Storing audit logs When storing audit logs, you can temporarily store them on a system disk before storing the logs in the SVP, or store audit logs directly in the SVP.
PAGE 28
3 Quick reference This topic provides a quick reference to what each log indicates. Audit Log Functions The following table lists the functions used in audit logging and provides their meanings.
PAGE 29
Remote Web Console and SVP operation The storage system logs operations performed from Remote Web Console computer or SVP. The following table lists the function/operation names as well as GUI operations that trigger logging. Functions are listed in alphabetical order.
PAGE 30
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation BASE HCSSO Authentication Launching Remote Web Console from Command View Advanced Edition Suite BASE HCSSO SetOneTimeKey Issuing OneTimeKey from Command View Advanced Edition Suite BASE Login Log in to Remote Web Console or SVP BASE Logout Log out from Remote Web Console or SVP BASE Release HTTP Block Changing settings on the Release HTTP Blocking window BASE Resume
PAGE 31
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Install Change Host Group Maintenance on SVP Install Change WWN Maintenance on SVP Install DCR Prestaging Maintenance on SVP Install Define Config.
PAGE 32
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) 32 Function Name Operation Name Corresponding GUI Operation Install Set Subsystem Time Maintenance on SVP Install Set UserAuth Maintenance on SVP Install System Option Maintenance on SVP Install System Tuning Maintenance on SVP Install Update Config Maintenance on SVP Install Volume to Space Maintenance on SVP Local Replication Add Reserve VOLs Reserving volumes for Business Copy or Business Copy Z Local Replicatio
PAGE 33
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Maintenance Size Change Maintenance on SVP Maintenance Spare Disk Maintenance on SVP Maintenance Switch SVP Maintenance on SVP Maintenance Transfer Config Maintenance on SVP Maintenance Type Change Maintenance on SVP Maintenance Verify Maintenance on SVP Maintenance Verify Stop Maintenance on SVP Monitor Threshold Maintenance on SVP Perf Mon DCR Prestaging
PAGE 34
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Assign MP Blade Assigning a MP blade PROV Block LDEVs Blocking LDEVs PROV Change Host Group LUN Manager operation using Configuration File Loader PROV Complete SIMs Completing SIMs related to a pool PROV Create Host Groups Creating a host group PROV Create LDEVs • Creating a basic volume • Creating an external volume • Creating a virtual volume for Snapshot •
PAGE 35
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Edit LDEV Tier Rank Editing the external LDEV tier ranks of pool volumes assigned to a pool PROV Edit MP Blades Editing the MP blade setting PROV Edit Ports(Address) Editing a port address PROV Edit Ports(Attr) Changing a port attribute with Continuous Access Synchronous, Continuous Access Synchronous Z, Continuous Access Journal, Continuous Access Journal Z, Extern
PAGE 36
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Reclaim Zero Pages Releasing pages in a virtual volume PROV Release HostReserved Releasing Host-Reserved LUNs PROV Release LUSE Releasing an LUSE volume PROV Relocate Pool Starting the tier relocation of a pool PROV Remove Hosts Removing a host from a host group PROV Restore LDEVs Restoring an LDEV PROV Restore Pools Restoring a pool PROV Set Channel Spee
PAGE 37
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Stop Reclm ZeroPages Stop releasing pages in a virtual volume PROV Stop Relocating Stopping the tier relocation of a pool PROV Stop Shrinking Pool Stop decreasing pool capacity PROV VTOC Volume Retention RCU Add Path RCU settings for Continuous Access Synchronous, Continuous Access Synchronous Z, Continuous Access Journal, or Continuous Access Journal Z Add RCU
PAGE 38
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PFCGrp Del/Chg Update Port WWN Update PFCGrp Update WWN Spreadsheet CflSet End CflSet Start Cnt Ac-S Executing the CFLSET command using Remote Web Console CLI LUNM Operation LUNM Operation using Configuration File Loader VR Operation VR operation using Configuration File Loader Change Option Continuous Access Synchronous Change Pair Option Function Switch Paircreate Pairr
PAGE 39
Table 7 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Journal-Vol Pair-Option R-Cmd.Dev.
PAGE 40
Command sent from the host The following table describes the function name output to the audit log file when receiving commands from the host. Table 8 Audit Log and Command Sent from Host Function Name Description Config Command Indicates that a configuration command was received. FC-SP Indicates that the FC-SP authentication is completed. User Auth Indicates that a user authentication command was received.
PAGE 41
Table 10 Audit Log and Single Sign-on Operation (continued) Function Name Operation Name Corresponding GUI Operation SSO Authentication Authenticating token information SSO SetOneTimeKey Registering a one-time key Audit log reproduced output The following table describes the operation name, event name, and triggering events that are output when the audit log file is reproduced. The "create file" event name will be automatically output only once.
PAGE 42
4 Audit log examples This topic provides examples and descriptions of the audit logs produced by each function and operation that can be performed with Remote Web Console and SVP. The descriptions are listed alphabetically by function name and operation name. For detailed information on the version numbers in log output examples, see Table 4 (page 18). Audit Log descriptions [AuditLog] Audit Log buffer Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 43
Example <14> Jan 4 06:25:18 SVP Storage: CELFSS,1.1,250001,, 2006-01-04T06:25:18.3Z, Storage,SVP,AnomalyEvent,Success,,R700:65307,, Japan-Tokyo,,,,,,,,,,,,SVP,,,[AuditLog],Over MaxLine,SVP,Normal end Basic Information Parameter Description SVP Indicates that the capacity of audit log file 1 has reached the maximum DKC Indicates that the capacity of audit log file 2 has reached the maximum [AuditLog] Over Threshold This information appears in the syslog file only.
PAGE 44
Item Description SrvAddr The IP address to which the audit log file is sent. If the setting has not changed, a hyphen (-) is displayed. UserName The user name to login to the FTP server. If the setting has not changed, a hyphen (-) is displayed. OutputDir The directory in the FTP server that the transferred audit log files are stored. If the setting is not changed, a hyphen (-) is displayed. [AuditLog] Set Syslog Server Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 45
[AuditLog] SIM Complete Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [AuditLog],SIM Complete,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Reference Code=[0x7C0300],Num. of Reference Codes=1 Detailed information Item Description Reference Code The SIM reference code which error and service request is solved. Num. of Reference Codes The number of SIM reference code which error and service request is solved.
PAGE 46
Detailed information Item Description User Group Name The name of a user group Result Result of the operation Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num. of User Groups The number of user groups Resource Group ID The resource group ID allocated to the user group Not the difference but all the resource group numbers are output, which are allocated to the target user group after the operation. Num.
PAGE 47
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{User Name,Result}=[{User01,Normal end}],Num of Users=1. Detailed information Item Description User Name The name of the user whose password was changed. Result Result of the operation Normal end: normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: part code, yyyyyy: error code Num. of Users The number of users whose passwords were changed. [ACM] Create User Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 48
Detailed information Item Description User Group Name The name of a user group name that was created All Resource Groups Assigned Indicates whether there is All Resource Groups Assigned setting in the created user group Result Result of the operation Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num. of User Groups The number of created user groups [ACM] Delete User Groups Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 49
[ACM] Edit User Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx,+00:00,RMI AP,uid=user-name,1, Task Name,[ACM],Edit User,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{User Name,Account Status,Authentication} =[{User01,Enabled,Local}],Num. of Users=1 Detailed information Index Description User Name The user name that was edited. Account Status Indicates whether the user account is enabled or disabled. A hyphen (-) appears if the setting is not changed.
PAGE 50
Name,Result} =[{User01,Group01,Normal end},{User02,Group01,Normal end}], Num of Users=2 Detailed information Item Description User Name The user name that was removed from a user group. User Group Name The name of the user group from which the user was removed. Result Result of the operation Normal end: normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: part code, yyyyyy: error code Num. of Users The number of users that were removed. [ACM] Set Login Message Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 51
Basic Information for Example 2 Parameter Description LDAP Indicates that the LDAP server is used as the External Authentication server Detailed Information for Example 2 Item Description Certificate File Name Indicates the name of certificate file DNS Lookup Indicates whether to search the LDAP server using the information registered in the SRV records in the DNS server Enable: Performs the search using information registered in the SRV records in the DNS server Disable: Performs the search using
PAGE 52
Domain Name,Base DN,Search User's DN,Timeout,Retry Interval, Number of Retries}= -{Enable,CFFILE,STARTTLS,Disable, -example.com,389,example1.com, -dc=example2 dc=com,example3.com,10,1,3} +Num. of Servers=1 Basic Information for Example 3 Parameter Description RADIUS Indicates that the RADIUS server is used as the External Authentication server.
PAGE 53
Item Description Timeout Indicates the number of seconds before the connection to the LDAP server times out Retry Interval Indicates the retry interval in seconds when the connection to the LDAP server fails Number of Retries Indicates the retry times when the connection to the LDAP server fails Num. of Servers The number of external authentication servers that are set Example 4 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 54
Item Description Disable: Does not connect an authentication server to an authorization server Certification File Name Indicates the name of certification file Authentication Protocol Indicates the LDAP protocol to use Primary Port Number Indicates the port number of the LDAP server Base DN Indicates the Base DN for searching for users to authenticate Commas that are input by user are indicated with spaces Search User's DN Indicates the DN of the user for searching Timeout Indicates the number
PAGE 55
Detailed information Item Description File Name Name of the backup file Result Result of the backup operation Normal end: normal end, Error (xxxx-yyyy): Abnormal end, -: not selected xxxx: part code, yyyy: error code [BASE] Control Panel Restore Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,0,, [BASE],Control Panel Restore,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 56
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{ID}={0,1,2,3},Num. of IDs=4 Detailed information Item Description ID ID (unique ID row by row) of the version information that was deleted Num. of IDs The number of IDs [BASE] Delete Reports Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[BASE],Delete Reports,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 57
Item Description xxxx: part code, yyyy: error code Num. of Tasks The number of the deleted tasks. [BASE] Disable Auto Delete Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Disable Auto Delete,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Task Name,Type,User Name,Submission Time,Result} =[{20100101-EditSubsystem,Edit Subsystem,User01, YYYY/MM/DD HH:MM:SS,Normal end},{20100101-CreateLdev, Create LDEV,User02,YYYY/MM/DD HH:MM:SS,Normal end}], Num.
PAGE 58
Item Description Primary Server: Primary syslog server Secondary Server: Secondary syslog server SIM Transfer Whether to notify the SIM syslog or not Enable: Notify the SIM syslog Disable: Do not notify the SIM syslog IP Version The version number of the internet protocol. When the SIM Transfer is set to Disable, a hyphen (-) is displayed. IPv6: Internet Protocol Version 6 IPv4: Internet protocol Version 4 IP Address The IP address to which the SIM syslog is notified.
PAGE 59
Item Description User Name ID of the user who performed the operation. Submission Time Time when the task was registered. Result Result of the operation Normal end: normal end, Error (xxxx-yyyy): Abnormal end,-: not selected xxxx: part code, yyyy: error code Num. of Tasks Number of the target tasks. [BASE] Entry Tasks This log is output when each task on the Remote Web Console menu is performed. Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 60
[BASE] HCSSO Authentication Example 1: When SSO authentication succeeded 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,0,, [BASE],HCSSO Authentication,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx * "0" is always output in the connection number. Example 2: When SSO authentication failed 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=,0,, [BASE],HCSSO Authentication,,Error(xxxxx-yyyyy), from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 61
Item Description -: disabled, Blocked: enabled Result Result of the HTTP Block setting Normal end: normal end, Error (xxxx-yyyy) Abnormal end xxxx: part code, yyyy: error code [BASE] Resume Tasks Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Resume Tasks,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 62
Item Description IPAddress Network address information (IPv4, IPv6, and network name) RegistryDate Time stamp of initial registration LastAccessDate Time stamp of the final access MemoRandom Memo space information Num. of CVAEInfos The number of Command View Advanced Edition Suite messages LicenseInfo License information Num. of LicenseInfos The number of license information messages [BASE] Set Up HTTP Block Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 63
Item Description Normal end: normal end, Error (xxxx-yyyyy): Abnormal end, -: xxxx: part code, yyyy: error code Num. of Tasks Number of the target tasks. [BASE] Unlock Forcibly Example 07xx,YYYY/MM/DD,HH:MM.SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Unlock Forcibly,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [BASE] Update SMIS CrtFiles Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 64
Parallel Access Volumes descriptions [PAV] Add Alias Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PAV],Add Alias,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LDKC=0x00,CU=0x00 ++{Alias LDEV,Base LDEV}=[{0xFD,0x00},{0xFE,0x00},{0xFF,0x01}], Num. of Alias LDEVs=3 +LDKC=0x00,CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num.
PAGE 65
E-Mail descriptions [E-Mail] MailAddress Write Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [E-Mail],MailAddress Write,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{MailServerSetting,MailServer}={HostName,smtp.test.co.jp} +{SMTP AUTH,Account}={Enable,Account} +{FromAddress,ReturnAddress}={TransAddr@co.jp,ReplyAddr@co.jp} +UsedCount=32 ++{ToAddressList,Attribute}=[{usr1@co.jp,TO},{usr2@co.jp,TO}, {usr3@co.jp,TO},{usr4@co.jp,CC}, [snip] {usr25@co.
PAGE 66
Compatible FlashCopy descriptions [FC Z] Set SCP Time Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [FC Z],Set SCP Time,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC,CU,SCP Time(s)}= -[{0x00,0x00,600},{0x00,0x01,600},{0x00,0x02,600}, {0x00,0x03,600},{0x00,0x04,600},(snip), {0x00,0xFE,600}], Num. of CUs=255 Detailed information Item Description LDKC The LDKC number. CU The CU number. SCP Time(s) The State Change Pending delay time in seconds.
PAGE 67
[ESAM] Del Quorum Disk ID Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [ESAM],Del Quorum Disk ID,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Quorum Disk ID,Paired S/N,Controller ID, Quorum Disk(LDKC:CU:LDEV),Result} =[{0x01,64024,6,0x00:0xFE:0x01,Normal end}, {0x02,64024,6,0x00:0xFE:0x02,Normal end},(snip), {0x7F,64024,6,0x00:0xFE:0x7F,Error(xxxx-yyyyy)}]-,Num.
PAGE 68
Item Description Entire: Copy all, None: Do not copy Fence Level The fence level set (the condition that MCU rejects the write operation to the primary volume). Never: No condition Copy Pace The initial copy speed set (the number of tracks you can copy at one time). Priority The priority of the set initial copy operation (scheduling order). Diff The unit of the differential management set. Auto, Cylinder, Track Quorum Disk ID The quorum disk ID to be used for a pair.
PAGE 69
[ESAM] Pairsplit-r Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [ESAM],Pairsplit-r,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),Type,S-VOL Write,Kind, Result} =[{1A-0x00-0x000,1B-0x00-0x000,P-VOL,Disable,S-VOL,Normal end}, {1A-0x00-0x001,1B-0x00-0x001,P-VOL,Disable,S-VOL,Normal end}, (snip)-(snip)],Num.
PAGE 70
Item Description Type The volume type of the volume on the primary site. P-VOL: Primary volume, S-VOL: Secondary volume Force The setting for forced pair deletion. Yes: the pair is deleted even when the MCU cannot communicate with the RCU. No: The pair is deleted when the MCU can change the pair status to SMPL only. Result The result of the operation. Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs.
PAGE 71
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Type=Total +{Total Defect Count}={15} ++PDEV=[HDD000-01,HDD000-02],Num. of PDEVs=2 Example 3: changing the threshold of the SSD when drive type is SLRxx-MxxxSS 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Information],ORM Value,Alter,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Type=Total +{Total Defect Count,Used Endurance Indicator}= {160000,(99,90)} ++PDEV=[HDD000-03],Num.
PAGE 72
Item Description DMA Error The threshold of the DMA Error Memory Error The threshold of the Memory Error Uncorrected Error The threshold of the Uncorrected Error Battery Error The threshold of the Battery Error FMD Battery Life Indicator The threshold of the Used Endurance Indicator PDEV The mounting location of the PDEV (physical device) that is the target of Alter or error reset. Num. of PDEVs The number of PDEVs. [Information] SIM Complete Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 73
Item Description ON: Report, OFF: Do not report Serious Report serious level information as a SIM. ON: Report, OFF: Do not report Moderate Report moderate level information as a SIM. ON: Report, OFF: Do not report Service Report service level information as a SIM. ON: Report, OFF: Do not report Num. of Types The number of information levels to be reported as a SIM. [Information] Threshold Value Example 1 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 74
Item Description Read/Write error (Recovered,Unrecd.) The threshold of the Read/Write error. Drive I/F error (Recovered,Unrecd.) The threshold of the Drive I/F error. Controller hardware error (Recovered,Unrecd.) The threshold of the Controller hardware error. SAS I/F error Port 0 (Unrecd.) The threshold of the SAS I/F error Port 0. SAS I/F error Port 1 (Unrecd.) The threshold of the SAS I/F error Port 1. Port 0 error (Unrecd.) The threshold of the Port 0 error. Port 1 error (Unrecd.
PAGE 75
[Install] Add LU Path Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Add LU Path,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,LUN,LDKC:CU:LDEV}=[{XX,0xXXX,0xXXX, 0xXX:0xXX:0xXX},{XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}, {XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}],Num. of Paths=3 Detailed information Item Description Port The name of the port to which the host group belongs. HostGrpID The host group number linked to the logical volume.
PAGE 76
Detailed information Item Description New Ver. The new version number. Old Ver. The old version number. [Install] Backup Config Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Backup Config,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Ver.=xx-xx-xx/xx Detailed information Item Description Ver. The version number of the configuration information to be backed up. [Install] Change Host Group Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 77
Detailed information Item Description Port The name of the port where the host is connected. HostGrpID The host group number on which the host with WWN or nickname of the host bus adapter being changed is registered. WWN Indicates the WWN of the host bus adapter before the change. Change WWN Indicates the WWN of the host bus adapter after the change. Change Nickname The nickname of the host bus adapter after the change. Num.
PAGE 78
Detailed information Item Description Port The name of the port to which the deleted or initialized host group belonged. HostGrpID The host group number that was deleted or initialized. Num. of Host Groups The number of host groups that was deleted or initialized. [Install] Delete LU Path Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Delete LU Path,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 79
[Install] Dku Emulation Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Dku Emulation,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Type=3390-3A +Type=3390-3A ++LDEV(LDKC:CU:LDEV)=[0x00:0x00:0x02,0x00:0x00:0x03], Num. of LDEVs=2 +Type=3390-3B ++LDEV(LDKC:CU:LDEV)=[0x00:0x00:0x04,0x00:0x00:0x05], Num. of LDEVs=2 +Num. of Emulation Types=3 Detailed information Item Description Type The emulation type.
PAGE 80
=[{3B,0x0FE,0x000},{3B,0x0FE,0x005},{3B,0x0FE,0x009}], Num. of LUNs=3 Detailed information Item Description Port The name of the port where the reserve attribute of the host is forcefully cancelled. HostGrpID The host group number. LUN Indicates LUN of the volume linked to the host group. Num. of LUNs The number of the LUNs where the reserve attribute of the host is forcefully cancelled.
PAGE 81
Item Description LDEV The LDKC number, the CU number, and the LDEV number Num. of LDEVs The number of LDEVs [Install] Initialize ORM Value Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Initialize ORM Value,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [Install] Install Example 1: installing additional channel adapters 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 82
Num. of Ports=8 +Num. of CHAs=4 Detailed information for example 1 Item Description CHA The channel adapter (CHA) mounting location. Kind The kind of PCB mounted. Port The mounting location of the port. Initiator/Target The type of Initiator or Target. Channel Speed The channel speed is indicated for open systems. 1: 1 Gbps, 2: 2 Gbps, 4: 4 Gbps, 8: 8 Gbps, 10: 10 Gbps, Auto: Auto mode. CU Number Indicates the range of the CU number that the port belongs. Num. of Ports The number of ports.
PAGE 83
Basic information for example 2 Parameter Description Progress Close The window that shows the progress of LDEV formatting has closed. Quick Format Quick Format is selected. Quick Format Close The window that shows the progress of preparing for Quick Format has closed. Note: No parameter is output for any case other than those described in this table. Detailed information for example 2 Item Description Disk Adapter (DKA) The Disk Adapter mounting location. Kind The type of Disk Adapter. Num.
PAGE 84
NOTE: Only the changed items will be output. The Detailed Information of the recovery process will not be output when the installation process executed before the process has completed. However, the setting of the recovery process will be output as the Detailed Information of the process when the installation process executed before the recovery process has not completed. Example 3: installing additional cache memory 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 85
Example 4: installing additional power supply 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Install,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +DKCPS=[DKCPS-02,DKCPS-03],Num. of DKC PSs=2 Detailed information for example 4 Item Description DKCPS The installed location of the power supply. Num. of DKC PSs The number of power supplies. Example 5: installing additional PCI 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 86
Basic information for example 7 Parameter Description SVP Indicates a change in the IP address of the SVP. SVP&DKC Indicates a change in the IP address of the SVP and the DKC. Detailed information for example 7 Item Description SVP The installed location of the SVP. IPAddress IP address in the SVP. Subnet Mask The subnet mask in the SVP. Use Duplex The duplex status of the SVP. Valid or Invalid will appear. SVP Kind The kind of the duplex status. Master SVP or Standby SVP will appear.
PAGE 87
[Install] Install CV This logged information indicates that the formatting was only requested but not completed. If the operation does not require the formatting, this logged information indicates that the volume was created. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Install CV,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 88
Detailed information Item Description Date Indicates the date and the time of the setting in “YYYY/MM/DD HH: mm” format (YYYY: year, MM: month, DD: day, HH: hour, mm: minute). [Install] Make LUSE Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Make LUSE,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 89
Detailed information Item Description PG The parity group number. E1-1: In case of an external volume. V1-1: In case of a virtual volume. X1-1: In case of a Thin Provisioning volume. LDKC:CU:LDEV The LDKC, CU, and LDEV numbers. Slot The slot number. A hyphen (-) is indicated for Make Volume. Emulation The emulation type. Size The CV capacity. Unit The unit of the CV capacity. System Disk The status of the system disk. Disable or Enable will appear. SSID The storage system ID.
PAGE 90
[Install] MP Install Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],MP Install,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Micro Program ={RAMBOOT,HTP,FCDG,DKCMAIN,DKAF},Num. of Kinds=5 +Target MP={MP00-1MA,MP01-1MA,MP02-1MA},Num. of MPs=3 Detailed information Item Description Micro Program The kind of microcode installed. Num. of Kinds The number of types of installed microcodes. Target MP The mounting location of the installed processor.
PAGE 91
[Install] Open DCR Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Open DCR,,Normal from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LDKC:CU:LDEV=0x00:0x00:0x00 ++{Define,Mode,Prestaging,Start LBA,End LBA} =[{Set,Bind,No,0,2015},{Set,Priority,Yes,3636,4175}, {Delete,-,-,3636,4175}],Num. of DCR Settings=3 Detailed information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number of the logical volume where Cache Residency is set.
PAGE 92
=[{CHA-1EU,16FC (Fibre )},{CHA-2QU,16FC (Fibre )}], Num. of CHAs=2 Detailed information for example 1 Item Description Channel Adapter The Channel Adapter mounting location Kind The kind of PCB mounted Num. of Channel Adapters The number of Channel Adapters Example 2: removing a Disk Adapter (DKA), an ECC Group or an LDEV 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Remove,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 93
=[{CLPR0,84992,1024,16384}],Num. of CLPRs=1 +PP Flag=[(64KLDEV, SI/VM Extension1, FCV2, FCSE, DP, CoW, TI, TPF),(SI/VM Extension2, CoW Extension)],Num. of PP Flags=2 +Max Number of CUs=64 Detailed information for example 3 Item Description CM The mounting location of the PCB for cache memory CMG The capacity of the CMG Size The capacity of the cache memory SSD0 The size of the SSD0 SSD1 The size of the SSD1 Num.
PAGE 94
Detailed information for example 6 Item Description MPB The installed location of the MPB. Auto LDEV Assignment The attribute of auto LDEV assignment. Example 7: removing SVP 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Remove,SVP,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{SVP}={SVP-OPTION} +{IPAddress,Subnet Mask}={(123.456.789.123),(255.255.255.
PAGE 95
Item Description IPv6(IPAddress, Subnet Prefix length) IPv6 (IPAddress: IP address, Subnet Prefix length: The value of subnet prefix) S-SVP Standby SVP details are provided in the format described below. IPv4(IPAddress,Subnet Mask) IPv4 (IPAddress: IP address, Subnet Mask: Subnet mask) IPv6(IPAddress, Subnet Prefix length) IPv6 (IPAddress: IP address, Subnet Prefix length: The value of subnet prefix) Example 8: removing SM PP flag 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 96
+Use Battery Life=Valid +{Battery,Date,Remained Life}=[{BATTERY-1CA,YYYY/MM/DD,990}, {BATTERY-2CC,YYYY/MM/DD,990}],Num. of Batteries=2 Detailed information Item Description Use Battery Life The status of Battery life function set. Valid: Valid, Invalid: Invalid Battery The mounting location of the battery Date Indicates the date of the setting in "YYYY/MM/DD" format (YYYY: year, MM: month, DD: day) Remained Life The remaining date of the battery shelf life.
PAGE 97
[Install] Set CommandDevSec Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set CommandDevSec,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,CommandDevSec}=[{0x00:0xXX:0xXX,Disable}, {0x00:0xXX:0xXX,Enable}],Num. of LDEVs=2 Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device is set.
PAGE 98
[Install] Set Fibre Topology Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set Fibre Topology,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Fabric,Connection} =[{XX,Enable,FC-AL},{XX,Disable,FC-AL}, {XX,Enable,P-to-P},{XX,Disable,P-to-P}],Num. of Ports=4 Detailed information Item Description Port The name of the port where the topology of Fibre Channel is set. Fabric Indicates whether the Fabric switch is enabled or disabled.
PAGE 99
+{IPAddress,Subnet Mask}={(123.456.789.123),(255.255.255.255)} +Use Duplex=Valid +Svp Kind=Master SVP +IPv4=Valid +IPv6=Valid +{M-SVP IPv4(IPAddress,Subnet Mask), IPv6(IPAddress,Subnet Prefix length)} ={((111.222.333.444),(255.255.255.255)), ((1111:2222:3333:4444:5555:6666:7777:8888),(64))} +{S-SVP IPv4(IPAddress,Subnet Mask), IPv6(IPAddress,Subnet Prefix length)} ={((555.666.777.888),(255.255.255.
PAGE 100
Detailed information Item Description Port The name of the port where the LUN security setting is changed. Switch Indicates whether the LUN security setting is enabled or disabled. Disable or Enable will appear. Num. of Ports The number of ports where the LUN security setting is changed. [Install] Set Subsystem Time Example 1: the case of TOD change 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 101
Item Description Check Time The time when the time correction function is executed. Only HH (Hour: 00 to 23) is indicated for the execution time. Create SIM Indicates whether the SIM was created or not when the setting of time correction failed. ON: Created, OFF: Not created. [Install] Set UserAuth Example 07xx, YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set UserAuth,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 102
Item Description (Correction Copy) ON: Execute Correction Copy, OFF: Do not execute Correction Copy Copy Operation Indicates the setting status of Copy Operation (Dynamic Sparing). (Dynamic Sparing) ON: Execute Dynamic Sparing, OFF: Do not execute Dynamic Sparing Read Configuration Data Mode The method to allocate the serial number reported by Read Configuration Data command. Link Failure Threshold The threshold to report link failure.
PAGE 103
Detailed information Item Description Serial No. The serial number. IP Address Mode The IP address mode set. Based on Serial Number: Set the IP address from the serial number.Specified: Set the specified IP address. IP Address The IP address set. Subnet Mask The subnet mask set. Port The mounting location of the port. CU Number Indicates the range of the CU number that the port belongs. Emulation The emulation type. Num. of Ports The number of ports.
PAGE 104
Detailed information Item Description PG The parity group number. V1-1: In case of a virtual volume. E1-1: In case of an external volume X1-1: In case of a Thin Provisioning volume LDKC:CU:LDEV The LDKC number, the CU number and the LDEV number. Num. of LDEVs The number of LDEVs. Local Replication Descriptions [Local Replication] Add Reserve VOLs Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 105
=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,0,Normal end}, {0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,0,Error(xxxx-yyyyy)}], Num. of Pairs=2 Example 3: when the copy type is FS 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Create Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 106
{0xX:0xAA:0xBB,0xYY:0xCC:0xDD,Error(xxxx-yyyyy)}], Num. of Pairs=2 Example 2: when the copy type is FS 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Raplication],Delete Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=FS ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Normal end}, {0xX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyyy)}], Num.
PAGE 107
Detailed Information Item Description Copy Type The program product name for this operation BC: Business Copy, BC Z: Business Copy Z Swap & Freeze Indicates whether the Swap & Freeze option is enabled or disabled. Enable: Enabled, Disable: Disabled Host I/O Performance Indicates whether the Host I/O Performance option is enabled or disabled. Enable: Enabled, Disable: Disabled FC Z Slower Copy1 Indicates whether the FC Z Slower Copy1 option is enabled or disabled.
PAGE 108
Detailed Information Item Description CU The CU number SCP Time(sec.) The state change pending time in seconds Num. of CUs The number of the CUs where the SCP time is set. [Local Replication] Release Reserved CTG Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Release Reserved CTG,,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=BC Z ++{CTG,Result}=[{0x01,Normal end},{0x02,Normal end}, {0x03,Normal end}],Num.
PAGE 109
[Local Replication] Reserve CTG Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Reserve CTG,,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=BC Z ++{CTG,Result}=[{0x01,Normal end},{0x02,Normal end}, {0x03,Normal end}],Num.
PAGE 110
Detailed Information Item Description Copy Type The program product name for this operation BC: Business Copy, BC Z: Business Copy Z, SS: Snapshot, FS: Fast Snap Copy Pace The copy speed Faster: High speed, Medium; Medium speed, Slower: Low speed This item is output only when the copy type is BC or BC Z.
PAGE 111
{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyyy)}], Num. of Pairs=2 Detailed Information Item Description Copy Type The program product name for this operation BC: Business Copy, BC Z: Business Copy Z, SS: Snapshot, FS: Fast Snap Copy Pace The copy speed Faster: High speed, Medium; Medium speed, Slower: Low speed This item is output only when the copy type is BC or BC Z.
PAGE 112
Item Description xxxx: Part code, yyyyy: Error code Num. of Pairs The number of the suspended pairs Maintenance descriptions [Maintenance] Blockade Example 1: blocking a PCB 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Blockade,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PCB=[CHA-1EU],Num. of PCBs=1 Example 2: blocking an LDEV 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 113
[Maintenance] Drive Interrupt Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Drive Interrupt,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PDEV=HDD000-00 Detailed information Item Description PDEV The mounting location of the PDEV (physical device). [Maintenance] Format The logged information indicates that the Format operation was only requested but not completed. Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 114
Item Description LDEV The LDKC number, the CU number, and the LDEV number. Num. of LDEVs The number of LDEVs. [Maintenance] MP Restore Example 07xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,SVP,uid=maintenance,0,, [Maintenance],MP Restore,,Error, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +MP=[MP08-2MC],Num. of MPs=1 Detailed information Item Description MP The identity of the microprocessor. Num. of MPs The number of microprocessors that were restored.
PAGE 115
[Maintenance] Quick Format The logged information indicates that the Quick Format operation was only requested but not completed. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Quick Format,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PG=[1-1],Num. of PGs=1 Detailed information Item Description PG The parity group number. E1-1: In case of an external volume. V1-1: In case of a virtual volume. X1-1: In case of a Thin Provisioning volume.
PAGE 116
Example 6: replacing a SSD 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance], Replace,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +SSD=SSD0(CACHE-1CA),Num. of SSDs=1 Detailed information Item Description Parts name The name of the parts (DKCPS-xx, DKCFAN-xxx, DKCPANEL-x,SSVPMN-x, PCIADP, PCICON, BATTERY-xxx, SVP-BASIC, SVP-OPTION, HUBBOX-xx, HDDPWR-xxxx, DKUPS-xxx, HDDFAN-xxx) specified to be replaced.
PAGE 117
Detailed information Item Description PCB The mounting location of the PCB (Channel Adapter (CHA), Disk Adapter (DKA), or MPB) to be restored. Num. of PCBs The number of PCBs to be restored. PDEV The location of the PDEV to be restored. PG The parity group number. E1-1: In case of an external volume. V1-1: In case of a virtual volume. X1-1: In case of a Thin Provisioning volume. Num. of PGs The number of parity groups. LDEV The LDKC number, the CU number, and the LDEV number. Num.
PAGE 118
[Maintenance] Size Change Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Size Change,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PCB=[CACHE-1CA],Num. of PCBs=1 +SIZE=4096 Detailed Information Item Description PCB The mounting location of the PCB (Cache Memory (CM)) Num. of PCBs The number of PCBs SIZE The cache capacity [Maintenance] Spare Disk Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 119
Detailed information Item Description SFP The port that Small Form-Factor Pluggables (SFPs) are inserted. Type The type of the Small Form-Factor Pluggable (SFP). Short Wave: Short wave, Long Wave: Long wave Num. of SFPs The number of inserted Small Form-Factor Pluggable (SFP)s. [Maintenance] Verify Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Verify,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PG=[1-1],Num.
PAGE 120
Monitor Descriptions [Monitor] Threshold Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Monitor],Threshold,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 121
{0x00:0x00:0x00,XXXXXX-XX,XXXXXX-XX}], Num. of LDEVs=2 Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume (for a mainframe system) where the setting information of Cache Residency cache is canceled. Start CC-HH The starting cylinder number (CC) and the starting head number (HH) of the cancelled data. End CC-HH The ending cylinder number (CC) and the ending head number (HH).
PAGE 122
Basic information Parameter Description Enable The monitored CU is enabled. Detailed information Item Description LDKC:CU The ID of the monitored CU The logical DKC number and the CU number are separated by colons and arranged in this order. [Perf Mon] Edit Monitoring SW Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Perf Mon],Edit Monitoring SW,Enable 60sec, Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 123
[Perf Mon] Edit WWN MonitorMode Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Perf Mon],Edit WWN MonitorMode,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Mode,HBA WWN,WWN Name}={Add WWN,0xXXXXXXXXXXXXXXXX, XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX}, ++Port=[XX],Num. of Ports=1, -Num.
PAGE 124
[Perf Mon] Set Open DCR Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Mon],Set Open DCR,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,Mode,Prestaging,Start LBA,End LBA} =[{0x00:0x00:0x00,Bind,No,XXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}], Num.
PAGE 125
[PP KEY] PP Disable chk Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PP KEY],PP Disable chk,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P.P.Name,Result}=[{JAVA API,Normal end}],Num. of PPs=1 Detailed information Item Description P.P.Name The name of the disabled program product. Result The result of checking the disabled program product. Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num.
PAGE 126
Item Description Result The result of installation. Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num. of PPs The number of the installed options. [PP KEY] PP Install File chk Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PP KEY],PP Install File chk,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +File Name=C:\Dkc200\Home\Sample.plk ++{P.P.
PAGE 127
Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Add Host Group,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,HostGrpName,Mode,Option[0:31],Option[32:63], Option[64:95]}={XX,0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX, 0xXXXXXXXX,0xXXXXXXXX} ++{WWN,Nickname}=[{0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}, {0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}],Num.
PAGE 128
[PROV] Add LU Path This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,,uid=user-name,1,, [PROV],Add LU Path,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,LUN,LDKC:CU:LDEV} =[{XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}, {XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}, {XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}],Num.
PAGE 129
{XX,0xXXX,0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}], Num. of WWNs=2 Detailed information Item Description Port The name of the port to which the host group belongs. HostGrpID The host group number where the host was registered. WWN Indicates WWN of the host bus adapter for the host registered in the host group. WWN is a 16-digit number in the hexadecimal format. Nickname The nickname of the host bus adapter for the host registered in the host group. Num.
PAGE 130
[PROV] Change Host Group This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Change Host Group,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,HostGrpName}=[{XX,0xXXX,XXXXXXXXXXXXXXXX}, {XX,0xXXX,XXXXXXXXXXXXXXXX}],Num. of Host Groups=2 Detailed information Item Description Port The name of the port to which the host group belongs.
PAGE 131
Item Description HostGrpName The name of the host group newly added. Num. of Host Groups The number of host groups added. [PROV] Create LDEVs Example 1 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create LDEVs,Basic,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 132
Example 2: Snapshot 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create LDEVs,Snapshot,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,LDKC:CU:LDEV,LDEVCapa(blocks),Emulation,CLPR,SSID, MP Blade ID,Result}=[{-,0x00:0x00:0x00,96000,OPEN-V,0,0x0004, Auto,Normal end},{-,0x00:0x01:0x00,96000, OPEN-V, 0,0x0005,, Auto,Normal end}],Num.of LDEVs=2 Example 3: Thin Provisioning 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 133
[PROV] Create Resource Grps Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create Resource Grps,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Resource Group ID,Resource Group Name,Result} =[{1,RSG1,Normal end},{2,RSG2,Normal end}], Num. of Resource Groups=2 Detailed Information Item Description Resource Group ID The resource group ID of a created resource group. A hyphen (-) is output when the creating operation failed.
PAGE 134
Item Description Subscription Limit(%) The reserve amount of the created or expanded pool. The unit is indicated as a percentage. If the reserve amount is not specified, it outputs “Unlimited.” If the pool type is Snapshot or Fast Snap, a hyphen (-) is output. Tier Management The auto control mode of the created or expanded pool. Auto: Auto, Manual: Manual If Multi Tier Pool is anything other than Enable, a hyphen (-) is output.
PAGE 135
Detailed information Item Description Port The name of the port to which the deleted or initialized host group belonged. HostGrpID The host group number deleted or initialized. Num. of Host Groups The number of host groups deleted or initialized. [PROV] Delete Host Groups Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Delete Host Groups,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID} =[{XX,0xXXX},{XX,0xXXX}],Num.
PAGE 136
Example 2: Snapshot 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Delete LDEVs,Snapshot,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV, Result}=[{0x00: 0x00: 0x00, Normal end}, {0x00: 0x01: 0x00, Normal end}, {0x00: 0x02: 0x00, Normal end}], Num. of LDEVs=3 Example 3: Thin Provisioning 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 137
Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Delete LU Path,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,LUN,LDKC:CU:LDEV} =[{XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}, {XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}, {XX,0xXXX,0xXXX,0xXX:0xXX:0xXX}],Num. of Paths=3 Detailed information Item Description Port The name of the port to which the host group belongs. HostGrpID The host group number where the LU path is deleted.
PAGE 138
Item Description xxxx: Part code, yyyyy: Error code Num. of Resource Groups The number of deleted resource groups [PROV] Delete WWN This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Delete WWN,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,WWN} =[{XX,0xXXX,0xXXXXXXXXXXXXXXXX},{XX,0xXXX,0xXXXXXXXXXXXXXXXX}], Num.
PAGE 139
Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device authentication setting is changed. UserAuth Indicates whether the command device authentication setting is enabled or disabled. Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the command device authentication setting is changed. [PROV] Edit Cmd Dev(DevGrp) Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 140
[PROV] Edit Command Devices Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Command Devices,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,CommandDev}=[{0xXX:0xXX:0xXX,Disable}, {0xXX:0xXX:0xXX,Enable}],Num. of LDEVs=2 Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device setting is changed.
PAGE 141
Item Description Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of LDEVs * The number of the logical volume(s) where the attribute has been set. When bit 5, 6, and 7 are all 0 (zero), Read/Write has been set. [PROV] Edit Host Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Host,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 142
Item Description See the HP XP P9000 Provisioning for Open Systems User Guide for the meaning of the host mode options. Num. of Host Groups The number of host groups that the host mode setting is changed.
PAGE 143
Table 14 Host mode option 32 to 63 and output contents of Option[32:63] (continued) Host mode option Value of Option[32:63] Host mode option Value of Option[32:63] 45 0x00040000 61 0x00000004 46 0x00020000 62 0x00000002 47 0x00010000 63 0x00000001 Table 15 Host mode option 64 to 95 and output contents of Option[64:95] Host mode option Value of Option[64:95] Host mode option Value of Option[64:95] 64 0x80000000 80 0x00008000 65 0x40000000 81 0x00004000 66 0x20000000 82 0x000020
PAGE 144
Item Description HostGrpName The name of the host group. If the name is changed, the name after change is indicated. Num. of Host Groups The number of host groups where the settings have been changed. [PROV] Edit LDEVs(tier) Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit LDEVs(tier),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,LDKC:CU:LDEV,Tier Relocation} =[{1,0x00:0x01:0x0F,Disable}],Num.
PAGE 145
Item Description LDEV Result The result of editing pool volumes per pool volume Normal end: Normal end Error(xxxx-yyyyy): Abnormal end Not Execute: Not executed where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of edited pool volumes [PROV] Edit MP Blades Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit MP Blades,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 146
Table 16 Addresses of Fibre Channel Port Value Address* Value Address* Value Address* Value Address* 1 EF (0) 33 B2 (32) 65 72 (64) 97 3A (96) 2 E8 (1) 34 B1 (33) 66 71 (65) 98 39 (97) 3 E4 (2) 35 AE (34) 67 6E (66) 99 36 (98) 4 E2 (3) 36 AD (35) 68 6D (67) 100 35 (99) 5 E1 (4) 37 AC (36) 69 6C (68) 101 34 (100) 6 E0 (5) 38 AB (37) 70 6B (69) 102 33 (101) 7 DC (6) 39 AA (38) 71 6A (70) 103 32 (102) 8 DA (7) 40 A9 (39) 72 69 (71) 104 31 (
PAGE 147
[PROV] Edit Ports(Attr) Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Ports(Attr),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Attribute=RCU Target ++Port=[1E],Num. of Ports=1 Detailed information Item Description Attribute The attribute of the port after change. Target: Target port, Initiator: Initiator port, RCU Target: RCU Target port, External: External port Port The name of the port where the setting is changed. Num.
PAGE 148
[PROV] Edit Ports(Topology) Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Ports(Topology),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Fabric,Connection}=[{XX,Enable,FC-AL},{XX,Disable,FC-AL}, {XX,Enable,P-to-P},{XX,Disable,P-to-P}],Num. of Ports=4 Detailed information Item Description Port The name of the port where the topology of Fibre Channel is changed.
PAGE 149
Detailed Information Item Description Tiering Policy ID The tiering policy ID Tier1 Max(%) The upper limit threshold value for the Tier1 The threshold value is displayed in the range 0 to 100. The unit is percent (%). This is output when the upper limit threshold value for the Tier1 is set. Tier1 Min(%) The lower limit threshold value for the Tier1 The threshold value is displayed in the range 0 to 100. The unit is percent (%). This is output when the lower limit threshold value for the Tier1 is set.
PAGE 150
Item Description where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of edited volumes [PROV] Edit V-VOL Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit V-VOL Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,LDKC:CU:LDEV,Tiering Policy ID, New Page Assignment Tier,Relocation Priority,Result} =[{0,0x00:0x00:0x00,1,Middle,Default,Normal end}], Num.
PAGE 151
Detailed information Item Description Command The operation on the pool Change: Changing pool information about the threshold and the subscription limit Change Tier: Changing information about Smart Tiers Delete: Delete pool Pool ID The pool ID of the pool where the settings have been changed or the number of the pool that have been deleted Pool Type The pool type Snapshot: Snapshot, Thin Provisioning: Thin Provisioning, Fast Snap: Fast Snap.
PAGE 152
Item Description Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed xxxx: Part code, yyyyy: Error code Num.
PAGE 153
Detailed information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number of the V-VOL Pool ID The pool ID of the pool corresponding to the expanded V-VOL Capacity The capacity of the V-VOL after expanding in LBAs Num. of VOLs The number of the expanded V-VOLs [PROV] Format LDEVs The logged information indicates that the Format operation was only requested but not completed. Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 154
Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Format LDEVs(Q),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02, 0x00:0x00:0x03,0x00:0x00:0x04,0x00:0x00:0x05, 0x00:0x00:0x06,0x00:0x00:0x07,0x00:0x00:0x08, 0x00:0x00:0x09,0x00:0x00:0x0A],Num. of LDEVs=10 Detailed information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number. Num.
PAGE 155
Detailed information Item Description LUSE(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of several LDEVs combined into an LUSE volume. The number indicated at the beginning represents the LDKC, CU, and LDEV numbers of the top LDEV. Num. of LUSEs The number of LUSE volumes configured. [PROV] Map Virtual HostGrp Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Map Virtual HostGrp,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 156
Item Description Virtual SSID The SSID of the virtual LDEV Virtual LUSE The number of LUSE volumes of the virtual LDEV Virtual Attribute The attribute of the virtual LDEV CVS: CVS attribute, -: No attribute Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy):Abnormal end where xxxx: Part code, yyyyy: Error code Num.
PAGE 157
Detailed Information Item Description Resource Group ID(From) The source resource group ID to which the resource belongs Resource Group ID(To) The target resource group ID Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, xxxx: Part code, yyyyy: Error code LDKC:CU:LDEV The logical DKC, CU, and LDEV numbers of the moved LDEV. LDEVResult The result of the LDEV Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, xxxx: Part code, yyyyy: Error code Num.
PAGE 158
Detailed information Item Description Pool ID The pool group number. Name The character string of a pool name. Result The result of the operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pools The number of specified pool groups. [PROV] Reclaim Zero Pages This log information does not indicate the completion of zero data pages reclaiming processing but the completion of zero data pages reclaiming operation.
PAGE 159
[PROV] Release LUSE Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Release LUSE,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LUSE(LDKC:CU:LDEV)=[0x00:0x00:0x00,0x00:0x01:0x00], Num. of LUSEs=2 Detailed information Item Description LUSE(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the top LDEV where LUSE volumes are released. Num. of LUSEs The number of LUSE volumes cancelled.
PAGE 160
[PROV] Restore LDEVs Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Restore LDEVs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02,0x00:0x00:0x03, 0x00:0x00:0x04,0x00:0x00:0x05,0x00:0x00:0x06,0x00:0x00:0x07, 0x00:0x00:0x08,0x00:0x00:0x09,0x00:0x00:0x0A], Num. of LDEVs=10 Detailed information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number. Num.
PAGE 161
Item Description 1: 1 Gbps, 2: 2 Gbps, 4: 4 Gbps, 8: 8 Gbps, Auto: Auto mode. Num. of Ports The number of ports where the channel speed is set. [PROV] Set CommandDev This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Set CommandDev,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 162
+{LDKC:CU:LDEV,DevGrpDef}=[{0xXX:0xXX:0xXX,Enable}], Num. of LDEVs=1 Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the volume where the device group definition is specified. UserAuth Indicates whether the device group definition is enabled or disabled. Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the device group definition is set. [PROV] Set FCSP Host Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 163
Item Description Reject Time The period of time to reject authentication when port authentication have failed. The unit is minute. Reject Count The number of authentication failures allowed before port authentication is rejected. Num. of Ports The number of ports where authentication parameter has been set. [PROV] Set FCSP Port Switch Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Set FCSP Port Switch,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 164
Item Description UserName The user name of the host group. Num. of Grps The number of host groups where authentication parameter has been set. [PROV] Set Fibre Address This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Set Fibre Address,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Fibre Addr.}=[{XX,0xXX(xx)},{XX,0xXX(xx)}],Num.
PAGE 165
Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Set Host Mode,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,Mode,Option[0:31],Option[32:63],Option[64:95]} =[{XX,0xXXX,0x00,0xXXXXXXXX,0xXXXXXXXX,0xXXXXXXXX},{XX,0xXXX, 0x4F,0xXXXXXXXX,0xXXXXXXXX,0xXXXXXXXX}],Num. of Host Groups=2 Detailed information Item Description Port The name of the port to which the host group belongs. HostGrpID The host group number.
PAGE 166
Item Description Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Page Ranges The specified number of page ranges Num. of VOLs The number of volumes where the tiering policy is set [PROV] Set Security Switch This log is output when LUN Manager operation is performed using Configuration File Loader. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],Set Security Switch,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 167
Detailed information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the volume where the user authentication is specified. UserAuth Indicates whether the user authentication is enabled or disabled. Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the user authentication is set. [PROV] Shrink Pool This log information does not indicate the completion of shrinking processing but the completion of shrinking operation. Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 168
Detailed Information Item Description Pool ID The pool ID of a pool where the performance monitoring stopped Result The result of stop monitoring the performance of pools Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed xxxx:Part code, yyyyy: Error code Num. of Pools The number of pools where the performance monitoring stopped [PROV] Stop Reclm ZeroPages Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 169
Detailed information Item Description Pool ID The pool ID of the pool where shrinking is stopped. Result The result of the stopping shrinking operation. Normal end: Normal end Not Execute: Not executed Error(xxxxx-xxxxxxx): Abnormal end xxxxx-xxxxxxx indicates error codes. Num. of Pools The number of pools where shrinking is stopped. [PROV] VTOC Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PROV],VTOC,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 170
+{S/N,MCU LDKC,MCU,RCU LDKC,RCU,SSID,Controller ID} ={99999,0x00,0x3F,0x00,0x7F,0x0004,4} ++{MCU Port,RCU Port} =[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G}, {5G,7G},{1H,3H}],Num. of Port Pairs=7 Detailed information Item Description S/N Indicates a serial number of the device. MCU LDKC The LDKC number of the connected LDKC. RCU LDKC The LDKC number of the paired LDKC. Path Gr.ID The path group ID. When the path group ID is default setting, “Default” is output. Controller ID The controller ID.
PAGE 171
Item Description Path Gr.ID The path group ID of the registered RCU. When the path group ID is default setting, Default is output. Controller ID The controller ID of the registered RCU device. MCU The CU number of the connected CU. RCU The CU number of the paired CU. SSID The SSID of the registered RCU. MCU Port The port number of MCU. RCU Port The port number of the registered RCU. Min.Path The number of set minimum paths.
PAGE 172
Item Description SSID Indicates SSID of the RCU where the optional setting is changed. Min.Path The minimum number of paths after change. MIH Time(s) The value of RIO MIH (Remote I/O Missing Interrupt Handler) timer (wait time until data copy from MCU to RCU is completed). The unit represents seconds. Round Trip Time(ms) The round-trip response time (delay time for round-trip remote I/O) after change. The unit is in milliseconds.
PAGE 173
[RCU] Delete RCU Example 1: CU Free is used 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [RCU],Delete RCU,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID} ={99999,0x00,0x00,Default,5} Example 2: CU Free is not used 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [RCU],Delete RCU,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 174
Detailed information Item Description MP Indicates the name of MP to be rebooted. [Remote Maintenance] Reboot Port Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RM AP,,,, [Remote Maintenance],Reboot Port,,Normal end,,,Seq.=xxxxxxxxxx +PORT=1E Detailed information Item Description Port Indicates the port name to be rebooted. [Remote Maintenance] Reboot SVP Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RM AP,,,, [Remote maintenance],Reboot SVP,,Normal end,,,Seq.
PAGE 175
Item Description Set: Reserve attribute is set, Reset: Reserve attribute is cancelled. VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the volume where the reserve attribute is set or cancelled. Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Vols The number of volumes where the reserve attribute is set or cancelled. [BC/SS] Initialize Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 176
+Copy Pace=Faster ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0,Normal end}, {0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyy)}], Num. of Pairs=2 Detailed information Item Description Copy Pace The set copy speed. Faster: High speed, Medium: Medium speed, Slower: Low speed P-VOL(LDKC CU:LDEV) The LDKC, CU, and LDEV numbers of the primary volume in the created pair.
PAGE 177
[BC/SS] Pairsplit Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BC/SS],Pairsplit,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Pace=Faster,Split Type=Quick Split ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0,Normal end}, {0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,1,Error(xxxx-yyyy)}], Num. of Pairs = 2 Detailed information Item Description Copy Pace The set copy speed.
PAGE 178
[BC/SS] Pairsplit-S Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BC/SS],Pairsplit-S,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),Result} =[{0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Normal end}, {0xAA:0xBB:0xCC,0xDD:0xEE:0xFF,Error(xxxx-yyyy)}], Num. of Pairs=2 Detailed information Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary volume in the deleted pair.
PAGE 179
[BC Z] Change Reserve Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BC Z],Change Reserve,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Attribute=Set ++{VOL(LDKC:CU:LDEV),Result}=[{0xZZ:0xXX:0xYY,Normal end}, {0xZZ:0xXX:0xYY, Error(xxxx-yyyy)}],Num. of Vols=2 Detailed information Item Description Attribute Indicates whether the reserve attribute is set or cancelled. Set: the reserve attribute is set, Reset: the reserve attribute is cancelled.
PAGE 180
{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,Error(xxxx-yyyy)}], Num. of Pairs=2 Detailed information Item Description S-VOL(LDKC CU:LDEV) The LDKC, CU, and LDEV numbers of the source volume in the deleted pair. T-VOL(LDKC CU:LDEV) The LDKC, CU, and LDEV numbers of the target volume in the deleted pair. Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs.
PAGE 181
Item Description Enable: Option is enabled, Disable: Option is disabled. OFFLINE DATA MIGRATION Indicates whether the Copy Pace Ext. Slower1option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled. This item may be displayed instead of Reserve 32. Copy Pace Ext. Slower2 Indicates whether the Copy Pace Ext. Slower2 option is enabled or disabled. Enable: Option is enabled, Disable: Option is disabled Copy Pace Ext. None Indicates whether the Copy Pace Ext.
PAGE 182
Detailed information Item Description Copy Pace The set copy speed. Faster: High speed, Medium: Medium speed, Slower: Low speed Split Type The split type. Quick Split: Pair split by background copy, Steady Split: Pair split by update copy, Migration: Data migration S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the source volume in the split pair. T-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the target volume in the split pair. Result The result of operation.
PAGE 183
Detailed information Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary volume in the deleted pair. S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary volume in the deleted pair. MU The Snapshot ID of the deleted pair. Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs.
PAGE 184
Item Description Name The nickname of the device set. Contact The setting name of the system administrator. Location The setting location of the device set. Performance Control Descriptions [Perf Ctl] Change PFCGrp Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Ctl],Change PFCGrp,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PFC Group,Priority,UpperLimit,Mode} =[{XXXXXXXXXXXXXXXX,Non-Prio,XXXXXXXX,IOPS}],Num.
PAGE 185
[Perf Ctl] Default Set Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Ctl],Default Set,Kind=WWN,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx Basic Information Parameter Description Kind=Port Indicates that settings in the Port tab are initialized. Kind=WWN Indicates that settings in the WWN tab are initialized. [Perf Ctl] Set All Prio Port Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 186
Item Description This information is output only when All Thresholds is configured. Mode The type of rate for All Thresholds IOPS: the I/O rate KB/s: the transfer rate This information is output only when All Thresholds is configured. [Perf Ctl] Set Ctrl Kind Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Ctl],Set Ctrl Kind,Kind=WWN,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 187
Item Description Mode The type of rate for the threshold or the upper limit IOPS: the I/O rate KB/s: the transfer rate This information is output only when a threshold or an upper limit is specified. Num. of Ports The number of ports whose settings are changed [Perf Ctl] Set Prio WWN Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Ctl],Set Prio WWN,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 188
=[{Update,XXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}], Num. of PFC Groups=1 Detailed Information Item Description Mode An executed operation Delete: Deleted a PFC group. Update: Changed a PFC name. PFC Group A PFC group name where the operation is executed Change Name A PFC group name after the change This information is output only when a PFC group name is changed. Num.
PAGE 189
=[{Add New Group,XXXXXXXXXXXXXXXX,Non-Prio,XXXXXXXX,IOPS}, ++WWN=[0xXXXXXXXXXXXXXXXX,0xXXXXXXXXXXXXXXXX],Num. of WWNs=2], +Num. of PFC Group=1 Detailed Information Item Description Update Mode An executed operation Add New Group: Added a new PFC group.
PAGE 190
Item Description A WWN is a 16-digit number in the hexadecimal format. When you changed an HBA, the WWN before the change is output. Change PFC Name A PFC name for the HBA When you changed a PFC name for the HBA, the PFC name after the change is output. Change WWN An WWN of the HBA after the change This information is output only when an HBA is changed. Num. of WWNs The number of HBAs whose settings are changed Spreadsheet descriptions [Spreadsheet] CflSet End Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 191
[Spreadsheet] VR Operation The Configuration File Loader log appears in the log file line. It is located between the line that contains "Start" and the line contains "End". Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Spreadsheet],VR Operation,Start,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 192
Item Description Yes: support, No: not support SCP Time(s) The SCP delay time when the pair is suspended. The unit is second. Max Initial Copy The number of parallel operation of initial copy by CU. (1 to 16). Num. of CUs The number of CUs set. [Cnt Ac-S] Change Pair Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-S],Change Pair Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 193
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),S/N,LDKC,ID, Controller ID,Type,Initial Copy,Fence Level, Copy Pace,Priority,Diff,Result} =[{1A-0x00-0x000,GR-0xFE-0x3FF,99999,0x00,Default,4,Sync,Entire, Never,15,032,Auto,Normal end},(snip) -(snip)],Num.
PAGE 194
Detailed information Item Description P-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the primary volume in the restored pair sequentially. S-VOL(Port-G-ID-LUN) The port number, host group number and LUN of the secondary volume in the restored pair sequentially. Fence Level The fence level set (the condition that MCU rejects Write to the primary volume).
PAGE 195
Item Description Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of split pairs. [Cnt Ac-S] Pairsplit-S Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-S],Pairsplit-S,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 196
Detailed information Item Description M-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the volume specified to the main volume when the pair is created. R-VOL(LDEV) The LDEV number of the volume specified to the remote volume when the pair is created. S/N The serial number of the device. LDKC The LDKC number of the paired LDKC. SSID Indicates the SSID of the RCU. Controller ID The controller ID of the RCU.
PAGE 197
Detailed information Item Description Max Initial Copy The maximum number of initial copy operations setting (1 to 512). CU Activity Indicates whether the parallel operation of initial copy by CU is enabled or not. Enable or Disable will appear. Path Blockade Watch(s) The path blockade watch period setting. The unit is second. Path Blockade SIM Watch(s) The path blockade SIM watch period setting. The unit is second. Service SIM Indicates whether the remote copy related SIM is reported or not.
PAGE 198
Item Description xxxx: Part code, yyyyy: Error code Num. of Pairs The number of changed pairs. [Cnt Ac-S Z] Clear SIM Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-S Z],Clear SIM,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [Cnt Ac-S Z] Delete Cmd.Dev Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-S Z],Delete Cmd.Dev,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 199
Detailed information Item Description Switch Each bit position (on/off) of the function switch information assigned by 64 bits. The beginning of the string is bit 0 and the ending of it is bit 63. “0” indicates the bit is off, and “1” indicates the bit is on. In the example above, bit 3 and bit 5 are on and the other bits are off. [Cnt Ac-S Z] Resume Pair Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 200
Basic information Parameter Description Run The script has been executed. Stop The script has been suspended. End The script has been completed. Detailed information Item Description FileName The file name of the executed script. [Cnt Ac-S Z] Suspend Pair Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-S Z],Suspend Pair,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 201
Detailed information Item Description LDKC The LDKC number of the journal. JNL The journal number. Data Overflow Watch(s) The overflow watch time of the metadata or journal data (in seconds). Inflow Control Indicates whether inflow control is executed or not. Yes: Controlled, No: Not controlled Use of Cache Whether to store the journal data in the restore journal in cache. Use: Store the journal data in cache. Not Use: Store the journal data in journal volume Result The result of the operation.
PAGE 202
Item Description Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Mirrors The number of mirrors. [Cnt Ac-J] Journal-Vol Example 1: Adding journal volumes 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J],Journal-Vol,Add,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 203
Item Description Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of LDEVs set for journals Num. of JNLs The number of journals. [Cnt Ac-J] Journal-Vol Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J],Journal-Vol,Delete-JNL,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 204
Item Description S/N The serial number of the logical device (storage system). CTRLID The controller ID. Priority The priority of copy. CTG The consistency group ID. Initial Copy Indicates whether initial copy or paircreate operation for Delta resync is executed or not. Entire: execute initial copy, None: do not execute initial copy, Delta: execute paircreate operation for Delta resync M-JNL The master journal number. R-JNL The restore journal number. Path Gr.
PAGE 205
Item Description M-JNL The master journal number. R-JNL The restore journal number. Error Level The error level. Mirror: Mirror level, LU: LU level Resync Mode Indicates the Resync Mode.Normal: normal resync, Delta: delta resync, Return to standby: return to standby status Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. [Cnt Ac-J] Pairsplit-r Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 206
[Cnt Ac-J] Pairsplit-S Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J],Pairsplit-S,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),MirrorID,S/N,CTRLID, Type,Range,Delete Mode,Result}=[{4C-0x00-0x000,4A-0x00-0x000, 0x00,67676,6,P-VOL,LU,Normal,Normal end},{4C-0x00-0x001, 4A-0x00-0x001,0x00,67676,6,P-VOL,LU,Normal,Normal end}], Num.
PAGE 207
Item Description M-JNL The master journal number. R-JNL The restore journal number. Error Level The error level. LU: volume level, Mirror: mirror level Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of changed pairs. [Cnt Ac-J] R-Cmd.Dev. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J Z],R-Cmd.Dev.
PAGE 208
[Cnt Ac-J] System-Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J],System-Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Max Initial Copy=64 Detailed information Index Description Max Initial Copy Indicates the number of volumes copiable at a time by one initial copy. Continuous Access Journal Z descriptions [Cnt Ac-J Z] Add-Pair Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 209
Item Description Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs [Cnt Ac-J Z] Change-JNL-Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J Z],Change-JNL-Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 210
Detailed information Item Description LDKC The LDKC number to which the journal belongs. JNL The journal number. MirrorID The mirror ID. Copy Pace The speed of initial copy. Low: Low speed, Medium: Medium speed, High: High speed Path Watch Time The path blockade watch period setting. The units are minutes, hours or days. If it is set to 30 minutes, it will be 30 (min.).
PAGE 211
Item Description If the LDKC:CU:LDEV is set using a spreadsheet and the Type is P-VOL, N/A will be output for both CU and LDEV numbers. MirrorID The mirror ID. S/N The serial number of the logical device (storage system). CTRLID The controller ID. N/A will be output when CTRLID is set by using spreadsheet. Type The primary and secondary of the deleted volume. P-VOL: Primary, S-VOL: Secondary Range The delete range. Volume: Volume range, Mirror: Mirror range Delete Mode The delete mode.
PAGE 212
Item Description JNL The journal number. MirrorID The mirror ID. S/N The serial number of the logical device (storage system). CTRLID The controller ID. Cmd.Dev.(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the remote command device. Result The result of the operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of JNLs The number of journals set for extended consistency groups Num.
PAGE 213
Detailed information Item Description LDKC The LDKC number where the journal belongs. JNL The journal number. Timer Type The timer type. System: System timer, Local: Local timer, None: No timer Cnt Ac-J Z 3DC Indicates if the journal supports 3DC multi-target configuration and 3DC cascade configuration of three Cnt Ac-J Z sites. Disable: Not supported, Enable: Supported LDKC:CU:LDEV The LDKC, CU, and LDEV numbers. Result The result of operation.
PAGE 214
+{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MirrorID,M-JNL,R-JNL, Error Level,CFW,Result}=[{0x00:0x00:0x00,0x00:0x20:0x00,0x03, 0x001,0x002,Volume,Only P-VOL,Normal end},(snip) -{0x00:0x00:0x02,0x00:0x20:0x02,0x03,0x001,0x002,Volume, Only P-VOL,Normal end},Num. of Pairs=3 Detailed information Item Description P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary data volume. S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary data volume. MirrorID The mirror ID.
PAGE 215
Item Description R-Cmd.Dev.(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the remote command device. The hyphen (-) indicates: • When assigning a remote command device without specifying a remote command device as a parameter. • When releasing a remote command device. Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Mirrors The number of mirrors changed. [Cnt Ac-J Z] Resume-Pair Example 07xx,YYYY/MM/DD,HH:MM:SS.
PAGE 216
Item Description xxxx: Part code, yyyyy: Error code Num. of Pairs The number of pairs. [Cnt Ac-J Z] Suspend-Pair Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J Z],Suspend-Pair,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 217
[Cnt Ac-J Z] System-Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Cnt Ac-J Z],System-Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Max Initial Copy=64 +{LDKC:CU,SIM Report}=[{0x00:0x00,Report},{0x00:0x01, Not Report},{0x00:0x02,Not Report},(snip) -(snip),{0x01:0xFE,Report}],Num. of CUs=510 Detailed information Item Description Max Initial Copy The number of volumes you can copy at a time during an initial copy operation.
PAGE 218
Detailed information Item Description Vendor The name of the vendor of the external storage system that the mapped external volume exists. Product The product name of the external storage system that the mapped external volume exists. Serial The serial number the external storage system that the mapped external volume exists. VolumeID1 The identification character 1 of the mapped external volume. VolumeID2 The identification character 2 of the mapped external volume.
PAGE 219
Item Description When a MP Blade ID is specified automatically, “Auto” is output. LDEVResult The result of attempting to create an external path. If the LDEV is created normally, the audit log includes the following: LDEVResult: Normal endIf the LDEV is not created, the audit log includes this:LDEVResult: Error(xxxx-yyyyy): Abnormal end where xxxx is the Part code and yyyyy is the Error code Num. of LDEVs The number of LDEVs in the mapped external volumes. Num.
PAGE 220
Item Description xxxx: Part code, yyyyy: Error code Num. of Volumes The number of volumes in the external volumes that mapping has been released. [Ext Stor] Disconnect ES Paths This logged information indicates that the Disconnect External Paths operation was only requested but not completed. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Disconnect ES Paths,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 221
[Ext Stor] Edit ES Path Config Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit ES Path Config,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{ExGroup,PathGroup,Result}={E1-1,1,Normal end} ++{Port,WWN,LUN,PathResult} =[{1A,50560E8000C3E211,0x0001,Normal end}, {2A,50560E8000C3E212,0x0001,Normal end}, {3A,50560E8000C3E213,0x0001,Normal end}, {4A,50560E8000C3E214,0x0001,Normal end}],Num.
PAGE 222
Example 2: Set the cache inflow control 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit ES VOLs, InflowControl,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Group,Mode,Result}=[{E1-1,Enable,Normal end}, {E1-2,Enable,Normal end},{E1-3, Enable,Normal end}, {E1-4, Enable,Normal end}],Num. of Groups=4 Basic information Parameter Description Cachemode The cache mode is changed. InflowControl The cache inflow control is set.
PAGE 223
[Ext Stor] Edit External WWNs Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit External WWNs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{WWN,I/O-TOV,Quedepth,LinkDown,Result} =[{50060E8000C3E214,15,8,180,Normal end}, {50060E8000C3E214,15,8,180,Normal end}, {50060E8000C3E214,15,8,180,Normal end},Num. of WWNs=3 Detailed information Item Description WWN The WWN of the external storage system.
PAGE 224
+{Config No.,Mode,Result}=[{10,0x00,Normal end}, {20,0x00,Normal end}],Num. of Profiles=2 Detailed information Item Description Config No. The configuration number of the profile operated setting. Mode The parameter of the execution mode on the setting operation. Result The result of the operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Profiles The number of Profiles operated setting.
PAGE 225
Detailed information Item Description Group The group number of the external volume resumed. Result The result of operation. Normal end: Normal end, Error (xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Groups The number of external volumes resumed. [Ext Stor] Split ES Path Grp Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Split ES Path Grp,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 226
[Auto LUN] Delete Auto Plan Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Auto LUN],Delete Auto Plan,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PlanNo}=[{1}],Num. of Plan = 1 Detailed information Item Description PlanNo The executed operation. Number: is output when a part of the auto migration plans is deleted. The number indicates what number of lines from the top of the auto migration plan list and the subsequent lines were deleted.
PAGE 227
Item Description PlanDay The setting value for sampling term. The output value depends on the sampling term output to PlanType. • If None is output to PlanType, nothing is output to PlanDay. • If Every day is output to PlanType, nothing is output to PlanDay. • If Once every X days is output to PlanType, the sampling interval is indicated. • If Once a week is output to PlanType, the specified day of the week is output to PlanDay.SUN, MON, TUE, WED, THE, FRI, or SAT is output.
PAGE 228
Item Description Set: Set to the fixed parity group, Release: Set to the normal parity group. PG ID of the parity group whose settings are changed. Num. of PGs The number of parity groups whose settings are changed. [Auto LUN] Set Migration Vol This logged information indicates that the migration was only requested but not completed. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Auto LUN],Set Migration Vol,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 229
Item Description Default: The default auto migration plan is applied (click Default, and then click Set). Customize: The customized auto migration plan is applied (click Set after changing the value of the auto migration plan parameter). StartTime The specified start time of the auto migration, that is, the time when the auto migration plan execution starts. TimeRequiredMax(min.) The specified upper limit of the migration time.
PAGE 230
Cache Partition descriptions [CPart] Edit CLPR Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [CPart],Edit CLPR,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Delete CLPR=[01],Num. of CLPRs=1 +CLPR=00:CLPR0,Cache(MB)=15360,Cache Residency(MB)=0, Num. of Cache Residency Areas=16384 ++PG=[1-1,1-2,1-3,1-4],Num. of PGs=4 +Num. of CLPRs=1 Detailed information Item Description Delete CLPR The deleted CLPR number. This is output only when CLPRs are removed.
PAGE 231
[Shredder] End Shredding Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,,,,[Shredder], End Shredding,,Normal end,,Seq.=xxxxxxxxxx +{Times,Result} =[{1,Normal},{2,Normal},{3,Normal}],Num. of Data=3 Detailed information Item Description Times The order of the shredding processes A number from 1 to 8 is displayed.
PAGE 232
Item Description Output LDEV Indicates LDEVs whose shredding results are output to the file Num. of LDEVs The number of target LDEVs of Data Output Shred LDEV The LDEV to be shredded Num. of LDEVs The number of LDEVs to be shredded Volume Security for Mainframe Descriptions [Vol Sec Z] Set Group Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Vol Sec Z],Set Group,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 233
+++LDEV=[0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x0a, 0x0b,0x0c,0x0d,0x0e,0x0f,0x10,0x11,0x12,0x13,0x14,0x15,0x16,0x17, 0x18,0x19,0x1a,0x1b,0x1c,0x1d,0x1e, -0x1f,0x20,0x21,0x22,0x23,0x24,0x25,0x26,0x27,0x28,0x29,0x2a, 0x2b,0x2c,0x2d,0x2e,0x2f,0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37, 0x38,0x39,0x3a,0x3b,0x3c,0x3d,0x3e,0x3f, (Snip) -0xf9,0xfa,0xfb,0xfc,0xfd,0xfe,0xff],Num. of LDEVs=xxx +Num.
PAGE 234
Compatible XRC descriptions [XRC] Set XRC Option Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [XRC],Set XRC Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{CLPR,LV2 THD(%),Block Option,Donot Block,LV1 Sleep, Sleep Time(ms),LV1 SIM,LV2 Suspend} =[{00,50,Cache,Disable,Disable,100,Disable, Disable}, -{01,70,Cache,Enable ,Disable,10,Disable,Disable}, -{02,60,Cache,Disable,Disable, 10,Enable ,Enable }], Num.
PAGE 235
Detailed information Item Description PDEV The mounting location of the PDEVs (physical devices) to be replaced. Num. of PDEVs The number of PDEVs to be replaced.
PAGE 236
5 Audit log examples of commands sent from the host This chapter provides examples and descriptions of the audit logs produced by commands sent from hosts or computers using the RAID Manager. The descriptions are listed alphabetically by function name and operation name. For detailed information on the version numbers in log output examples, see Table 4 (page 18). Config Command 07xx,YYYY/MM/DD,HH:MM:SS.xxx,+09:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept,from=host-name,,Seq.
PAGE 237
6 Audit log examples for encryption key operations This topic provides examples and descriptions of the audit logs produced by data encryption operations. The descriptions are listed alphabetically by function name and operation name. For detailed information on the version numbers in log output examples, see Table 4 (page 18) [ENC] Backup Keys The logged information is output when backup information is created in the storage system to back up encryption key information outside.
PAGE 238
Item Description For details on return values, see the manual for the key management server. Num. of Keys The number of backed up keys [ENC] Create Keys Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task name,[ENC],Create Keys,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxx +{Enc Key Number}=[1,2],Num. of Keys=2 Detailed Information Item Description Enc Key Number The encryption key number Num.
PAGE 239
Example 2: Creating protection keys 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task name,[ENC],Create Keys On Serv,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxx +{ Key Type,UUID,Result,Server_Reply} =[{KEK,K_SEC_DATA-9ac373fa-351c-415a-a2ab-154a0638c953, Normal end,-}],Num.
PAGE 240
Detailed Information Item Description UUID The UUID of the deleted encryption key in the key management server Backup Date The backup date set to the deleted encryption key Description The description of the deleted encryption key Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end Server_Reply The return value from the key management server A hyphen (-) is output except when the operation ended abnormally.
PAGE 241
Lowercase Characters , Symbols , Total }={0,0,0,0,6}, Num. of Settings=1 Detailed Information Item Description Numeric Characters The minimum number of characters for the Numeric Characters Uppercase Characters The minimum number of characters for the Uppercase Characters Lowercase Characters The minimum number of characters for the Lowercase Characters Symbols The minimum number of characters for the Symbols Total The total of the respective minimum number of characters Num.
PAGE 242
[ENC] Restore Keys fr Serv This logged information is output when the backup of the encryption key information is obtained from the key management server. Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Restore Keys fr Serv,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{UUID,Backup Date,Description,Result,Server_Reply} =[{KEY-cf20025e-b35b-492a-a0d2-65c9a0875951,2011/11/12 14:30:00, For Backup,Normal end,-}],Num.
PAGE 243
Example 2: not using a key management server 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Setup Key Mng Serv,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Key Management Server}=[{Disable}],Num. of Servers=1 Detailed Information Item Description Key Management Server Indicates whether a key management server is used. Enable: A key management server is used. Disable: A key management server is not used.
PAGE 244
7 Audit log examples for single sign-on This chapter provides examples and descriptions of the audit logs produced for single sign-on. The descriptions are listed alphabetically by function name and operation name. For detailed information on the version numbers in log output examples, see Table 4 (page 18). [BASE] Certificate Import Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Certificate Import,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
PAGE 245
[BASE] SSO Authentication Example 07xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP, uid=SI22G-NEC00\Administrator,1,,[BASE],SSO Authentication,, Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +User=SI22G-NEC00\Administrator,from=158.214.135.87, SSO UA=Administrator Detailed information Item Description User The user name of Single Sign-On. from The IP address of HP System Insight Manager Server. SSO UA The user access authority of Single Sign-On.
PAGE 246
8 Support and other resources Contacting HP For worldwide technical support information, see the HP Support Center: http://www.hp.
PAGE 247
• http://www.hp.com/support/downloads • http://www.hp.
PAGE 248
WARNING! CAUTION: IMPORTANT: NOTE: TIP: Indicates that failure to follow directions could result in bodily harm or death. Indicates that failure to follow directions could result in damage to equipment or data. Provides clarifying information or specific instructions. Provides additional information. Provides helpful hints and shortcuts.
PAGE 249
A Audit log user operations This appendix describes user operations that trigger logging. The same log is output when a user performs an operation using each Remote Web Console menu, clicking a button on the main window, or using General Tasks.
PAGE 250
Table 20 Logical Device (continued) GUI operation Submenu Audit Log Output Description Function Operation Name Edit LDEVs(tier) Edit V-VOL Option Format LDEVs Formatting an LDEV PROV Format LDEVs Formatting a LDEV using the Write to Control Blocks function PROV Format LDEVs(H) Quick formatting an LDEV PROV Format LDEVs(Q) Block LDEVs Blocking LDEVs PROV Block LDEVs Restore LDEVs Restoring an LDEV PROV Restore LDEVs Shred LDEVs Shredding an LDEV Shredder Shred LDEVs Abort Shredding1
PAGE 251
Table 21 Port/Host Group GUI operation Audit Log Output Submenu Description Function Name Operation Name Create Host Groups Creating a host group PROV Add Hosts Create Host Groups Edit Host Grps(Mode) Delete Host Groups Deleting a host group PROV Delete Host Groups Edit Host Groups Editing host group settings PROV Edit Host Grps(Name) Edit Host Grps(Mode) Add Hosts Adding a host to the selected host group PROV Add Hosts Add to Host Groups Adding the selected host to a host group Remo
PAGE 252
Table 21 Port/Host Group (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Registering authentication Information PROV Set FCSP Port Switch1, 2 Authentication Mode: bi-directional -> unidirectional or unidirectional -> bi-directional Authentication (Port) : Enable -> Disable or Disable -> Enable 1 When you apply two or more settings of the same type to the storage system at the same time, the log information is output as one entry.
PAGE 253
Table 23 Parity Group GUI operation Audit Log Output Submenu Description Function Name Operation Name Edit Encryption Enabling/disabling the encryption in a parity group level.
PAGE 254
Table 25 Local Replications (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name Business Copy Z, Fast Snap, or Snapshot Suspend Pairs Suspending pairs for Business Local Replication Suspend Pairs Copy/Snapshot or Business Copy Z Delete Pairs Deleting pairs for Business Copy/Snapshot, Business Copy Z, Fast Snap, or Snapshot Local Replication Delete Pairs Add Reserve Volumes Reserving volumes for Business Copy/Snapshot or Business Copy Z Local Replication A
PAGE 255
Table 27 Local Copy > Business Copy Z/Compatible FlashCopy GUI operation Audit Log Output Submenu Description Function Name Operation Name Pair Operation Add Pair BC Z Add Pair* Split Pair BC Z Split Pair* Resync Pair BC Z Resync Pair* Suspend Pair BC Z Suspend Pair* Delete Pair BC Z Delete Pair* Change Reserve BC Z Change Reserve* Initialize BC Z Initialize Option Option BC Z Option* CTG Add Consistency Group BC Z CTG* FC Z Set SCP Time* Delete Consistency Group FC Z S
PAGE 256
Table 28 Remote Copy > Continuous Access Synchronous (continued) GUI operation Submenu Quorum Disk Operation Audit Log Output Description Function Name Operation Name Function Switch Cnt Ac-S Function Switch Add Quorum Disk ID ESAM Add Quorum Disk ID1 Delete Quorum Disk ID ESAM Del Quorum Disk ID1 1 When you apply two or more settings of the same type to the storage system at the same time, the log information is output as one entry.
PAGE 257
Table 29 Remote Copy > Continuous Access Journal (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name Optional Operation Change System Option Cnt Ac-J System-Option1 1 When you apply two or more settings of the same type to the storage system at the same time, the log information is output as one entry. 2 If one or more settings end abnormally when you have applied at one time, the output log information is Error, not Warning.
PAGE 258
Table 31 Remote Copy > Continuous Access Journal Z GUI operation Audit Log Output Submenu Description Function Name Operation Name Journal Operation Edit JNL Volumes Cnt Ac-J Z Journal-Vol1 Change JNL Option Cnt Ac-J Z Change-JNL-Option1 Delete JNL Groups Cnt Ac-J Z Journal-Vol1 Change Mirror Option Cnt Ac-J Z Change-Mirror-Option1 Suspend Pair Cnt Ac-J Z Suspend-Pair1 Resume Pair Cnt Ac-J Z Resume-Pair1 Delete Pair Cnt Ac-J Z Delete-Pair1 Remove JNL from EXCTG (Force) Cnt Ac-J
PAGE 259
Table 32 Mainframe Connection GUI operation Audit Log Output Submenu Description Function Name Operation Name Parallel Access Volumes Add PAV Add Alias* If you perform the Add Alias and Delete Alias operations at the same time, Delete Alias is executed first. If Delete Alias operation fails, Add Alias is not executed.
PAGE 260
Table 33 Other function (continued) GUI operation Submenu Cache Residency Audit Log Output Description Function Name Operation Name Expiration-Lock PROV DRU Expiration Lock1 Set Cache Residency (Open Volume) Perf Mon Set Open DCR1, 2 Set Cache Residency (M/F Volume) Perf Mon Set M/F DCR1, 2 Release Cache Residency (Open Volume) Perf Mon Delete Open DCR1, 2 Release Cache Residency (M/F Volume) Perf Mon Delete M/F DCR1, 2 Prestaging ON Perf Mon DCR Prestaging1 The log information is outp
PAGE 261
Table 36 Performance Monitor GUI operation Audit Log Output Submenu Description Function Name Operation Name Edit Monitoring Switch Starting/stopping monitoring Perf Mon Edit Monitoring SW Edit CU Monitor Mode Setting target CUs for monitoring Perf Mon Edit CU Monitor Mode Edit WWN Monitor Mode Setting target WWNs for monitoring Perf Mon Edit WWN MonitorMode Add New Monitored WWNs Adding new WWNs for monitoring Perf Mon Edit WWN Monitor Mode Edit WWN Editing WWN Perf Mon Edit WWN Delete Un
PAGE 262
Table 37 Performance Control (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Deleting PFC group Perf Ctl Update PFCGrp1, 2 PFCGrp Del/Chg Set All Prio WWN Setting priority for PFC groups Perf Ctl (Attribute / Upper) Change PFCGrp1, 2 Changing PFC group name PFCGrp Del/Chg1, 2 Perf Ctl Set All Prio WWN Set All Prio WWN Clearing port settings due to removing port controllers Perf Ctl Clear PFC Info2 Notes: 1.
PAGE 263
Table 39 User Management (continued) GUI operation Audit Log Output Submenu Description Function Name Edit User Group Changing the name of a user ACM group Edit User Grp Delete User Groups Deleting a user group Delete User Grps Edit Resource Group Assignment Changing the resource group ACM assignment of a user group Assign Resource Grps Edit Role Assignment Changing the role assignment ACM of a user group Assign Roles ACM Operation Name Table 40 Resource Management GUI operation Audit Lo
PAGE 264
Table 41 Security (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name Encryption Keys Backing up keys to a server ENC Backup Keys > Backup Keys to Server Encryption Keys Backup Keys to Serv Restoring encryption keys ENC > Restore Keys from File Encryption Keys > Restore keys from Server Restore Keys Restore Keys fr File Restoring encryption keys from a server ENC Restore Keys Restore Keys fr Serv Table 42 Environmental Setting GUI operation Audit Lo
PAGE 265
Using Resource Lock menu Table 43 Resource Lock GUI operation Audit Log Output Submenu Description Function Name Operation Name Resource Lock Cancelling lock forcibly BASE Unlock Forcibly Using the window lunching from only other than menu Table 44 Window lunching only from other than menu GUI operation Audit Log Output Windows Description Function Name Operation Name CreateKeys Creating encryption keys on a server ENC Create Keys Create Keys On Serv Set keys to DKC CreateKeys Creating
PAGE 266
B Audit log SVP operations This appendix describes SVP operations as well as function names and operation names that are output to audit logs. Logging in to or out from SVP Table 47 Logging in to or out from SVP SVP Operations Audit Log Output Note Function Name Operation Name Login using the remote desktop access BASE Login No parameters or detailed information. Logout using the remote desktop access BASE Logout No parameters or detailed information.
PAGE 267
Table 48 Using Maintenance button on SVP (continued) SVP Operations Audit Log Output Function Operation Function Name Operation Name Maintenance Switch SVP Maintenance Switch SVP Maintenance Transfer Config Maintenance Transfer Config Using Install button Table 49 Using Install button on SVP SVP Operations Function Audit Log Output Operation Function Name Operation Name Define Configuration and Define Configuration and Install Install Install Define Config.
PAGE 268
Table 49 Using Install button on SVP (continued) SVP Operations Audit Log Output Function Operation Function Name Operation Name Change Configuration LUN Configuration Install Make LUSE Change Configuration LUN Configuration Install Release LUSE Change Configuration DCR Configuration Install DCR Prestaging Change Configuration DCR Configuration Install M/F DCR Change Configuration DCR Configuration Install Open DCR Change Configuration CVS Configuration Install Install CV Chang
PAGE 269
Using Monitor button Table 51 Using Monitor button on SVP SVP Operations Audit Log Output Function Operation Function Name Operation Name Threshold Threshold Monitor Threshold Using Monitor button 269
PAGE 270
C Conventions This appendix describes phrases in this manual that correspond to phrases in the Remote Web Console windows and messages. Business Copy, Business Copy Z, Fast Snap, and Snapshot volumes Business Copy, Business Copy Z, and Snapshot volumes displayed in the Remote Web Console windows and messages differ between Remote Web Console main windows and secondary windows. The differences are shown below.
PAGE 271
D Audit log GUI reference This topic describes the audit log screens in the Remote Web Console GUI. The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser. Actual windows may differ depending on the operating system and browser used. GUI contents also vary with licensed program products, disk array models, and firmware versions. Audit Log Properties dialog box Use this dialog box to download audit log files to Remote Web Console computer.
PAGE 272
Table 53 Syslog Window Item Description Output to Primary Server Specify whether to transfer the audit log to the primary syslog server. • Enable: Transfers the audit log. • Disable: Does not transfer the audit log. Primary Server Setting Set an IP address and a port number for the primary syslog server. Once you set Output to Primary Server to Enable, IP and Port become available. For both IP and Port, the defaults have been entered, so change them as needed.
PAGE 273
Table 54 Audit Log Transfer Window Item Description Output to Primary Server Specify whether to transfer the audit log file to the primary FTP server. • Enable: Transfers the file. • Disable: Does not transfer the file. Primary Server Setting Set an IP address for the primary FTP server. Once you set Output to Primary Server to Enable, IP becomes available. The default IP address has been entered, so change it as needed. You can set either IPv4 address or IPv6 address for IP address.
PAGE 274
Table 54 Audit Log Transfer Window (continued) Item Description Transfer to Secondary Server When you click Transfer, the audit log file is transferred to the secondary FTP server according to the settings selected on the audit log Transfer window. You can transfer the current audit log file without waiting for the audit log file to reach the threshold size for automatic transfer.
PAGE 275
Glossary AL-PA Arbitrated loop physical address. A 1-byte value that the arbitrated loop topology uses to identify the loop ports. This value becomes the last byte of the address identifier for each public port on the loop. BC P9000 or XP Business Copy. An HP application that provides volume-level, point-in-time copies in the disk array. BC Z The version of Business Copy that supports mainframe volumes. bit The basic unit of data in a binary numbering system (binary digit), represented by a 0 or a 1.
PAGE 276
LUN Logical unit number. A LUN results from mapping a logical unit number, port ID, and LDEV ID to a RAID group. The size of the LUN is determined by the emulation mode of the LDEV and the number of LDEVs associated with the LUN. LUSE Logical Unit Size Expansion. The LUSE feature is available when the HP StorageWorks LUN Manager product is installed, and allows a LUN, normally associated with only a single LDEV, to be associated with 1 to 36 LDEVs.
PAGE 277
synchronous Describes computing models that perform tasks in chronological order without interruption. In synchronous replication, the source waits for data to be copied at the destination before acknowledging that it has been written at the source. T-VOL Target volume. UDP User Datagram Protocol. UTC Coordinated Universal Time. V-VOL Virtual Volume. VOL, vol Volume. volume Volume on disk. An accessible storage area on disk, either physical or virtual. VSC Volume size customization.
PAGE 278
Index A H About audit logs, 23 Audit log examples, 244 Audit log file format, 14 Auto LUN descriptions, 225 HDD Easy Replace descriptions, 234 help obtaining, 246 HP subscription service, 246 technical support, 246 B Back up keys, 237 C Cache Partition, 230 Certificate import, 244 Changing the threshold of SAS, 70 Changing the threshold of the flash drive, 70 Changing the threshold of the FMD, 71 Changing the threshold of the SSD, 71 Compatible FlashCopy descriptions, 66 Compatible XRC descriptions, 23
PAGE 279
Volume Shredder descriptions, 230 W web sites HP subscription service, 246 websites HP , 246 product manuals, 246 279