HP XP7 Audit Log User and Reference Guide Abstract This document provides instructions for using the Audit Log function on HP XP7 Storage.
© Copyright 2014 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
Contents 1 Introduction.............................................................................................13 Overview..............................................................................................................................13 Features............................................................................................................................13 Audit Log file description...............................................................................................
[BASE] ControlPanel Restore................................................................................................57 [BASE] Create Conf Report..................................................................................................58 [BASE] Delete CVAE Info.....................................................................................................58 [BASE] Delete Reports.........................................................................................................
[Install] Format...................................................................................................................79 [Install] Format Stop...........................................................................................................80 [Install] Initialize ORM Value...............................................................................................80 [Install] Install......................................................................................................
[Maintenance] Size Change..............................................................................................116 [Maintenance] Spare Disk.................................................................................................117 [Maintenance] Switch SVP.................................................................................................117 [Maintenance] Transfer Config...........................................................................................
[PROV] Edit LDEV Tier Rank...............................................................................................143 [PROV] Edit MP Blades.....................................................................................................143 [PROV] Edit Ports(Address)................................................................................................144 [PROV] Edit Ports(Attr).......................................................................................................
[Remote Replication] Clear SIM.........................................................................................172 [Remote Replication] Create Pairs.......................................................................................172 [Remote Replication] Delete Cmd.Dev.................................................................................176 [Remote Replication] Delete Pairs.......................................................................................
Compatible XRC Descriptions.................................................................................................217 [XRC] Set XRC Option......................................................................................................217 HDD Easy Replace Descriptions..............................................................................................218 [HDDEasyReplace] Replace...............................................................................................
Add RCU Path.................................................................................................................236 Add Resource(Group).......................................................................................................237 Add Resource/Delete Resource..........................................................................................237 Add Snap Pool................................................................................................................
Modify Ldev(MP Blade)....................................................................................................261 Modify Ldev(Nick Name)..................................................................................................261 Modify Ldev(Restore)........................................................................................................262 Modify Ldev(SSID)............................................................................................................
SPLIT PAIRS.................................................................................................................288 SUSP PAIR..................................................................................................................288 TERM PAIR.................................................................................................................289 FC-SP..............................................................................................................................
1 Introduction Audit logs are created on the Service Processor (SVP) computer in the storage system. You can access the audit logs that are output by the SVP, but the SVP is accessible only by support personnel. Overview The audit log is an important tool that you can use to keep track of operations, to monitor security, to investigate the cause of errors, and to avoid potential errors. Audit logs are created on the SVP computer in the storage system.
Table 1 Audit Log File Components Component Audit Log File Syslog File File Type Text format. Text format. Auditlog information file 1 In syslogYYYYMMDD.tgz, there are syslog-svp.log (audit log file for SVP) and syslog-dkc.log (audit log file for DKC). Auditlog information file 2 Files are compressed in tgz format. Downloaded File Name audit-SVPYYYYMMDD.tgz or syslogYYYYMMDD.tgz audit-DKCYYYYMMDD.
Table 1 Audit Log File Components (continued) Component Audit Log File Syslog File is shown on the Remote Web Console main Also, the following log is output in the syslog file. window. • [AuditLog], Over MaxLine Threshold of the The threshold value is 70% (175,000 lines) of Maximum Number the maximum number of lines.
Figure 2 Audit Log File 2 (DKC) Basic Information Each item output in the audit log information file is delimited by commas (,). Table 2 Basic Information in Audit Log File No. Item File 1 (SVP) File 2 (DKC) Version XXYY indicates the model name (XX) and the Same as File 1. version number in audit log output format (YY). When the output format is changed, the value of YY is updated. See Table 4 (page 19) for the changed contents of XXYY.
Table 2 Basic Information in Audit Log File (continued) No. Item File 1 (SVP) File 2 (DKC) Interface • RMI AP indicates the log for Remote Web • In-band OPEN indicates open-system hosts. Console and Remote Method Invocation • In-band MF indicates mainframe system Applications such as CVAE. hosts. • SVP indicates the log for the SVP. • Out-of-band indicates hosts through the • RM AP indicates the log for Remote SVP. Maintenance Application. • No output for the event about encryption keys.
Table 2 Basic Information in Audit Log File (continued) No. Item File 1 (SVP) File 2 (DKC) Result The result of your operation. The result of the received commands. • Normal end. The operation has ended normally. • Normal end. The authentication has ended normally, or the event about encryption keys occurs. • Error (xxxx-yyyyy). The operation has ended abnormally. • Error. The authentication has ended abnormally. • Warning (xxxx-yyyyy).
hyphen (-) is output for a setting value, or a setting value is not output, or the item is not output. See the log examples in the followings below for details. • “Audit log examples” (page 44) • “Audit log examples of commands sent from hosts, computers using RAID Manager, or hosts using Business Continuity Manager ” (page 230) The following shows the symbols used in the detailed information.
Figure 3 Syslog File (RFC3164-compliant) Item 29 and 30 are output either one of them in one syslog information. Table 5 Items in the Syslog File (RFC3164-compliant) No. Item Description Priority The priority of an item in the syslog file is determined according to the following formula, enclosed by brackets (< >): Priority = 8 X Facility + Severity Facility is 1 (fixed). Severity depends on the type of log information: • 4: Error or Warning. Error means the operation has ended abnormally.
Table 5 Items in the Syslog File (RFC3164-compliant) (continued) No. Item Description If the "DD" is a single digit (for example, 1), it is displayed as " 1" (with a blank space before "1") and not as "01". Detected location The host name (SVP). Program name The detection entity identifier (Storage). Unified specification identification The Unified specification identifier (CELFSS). The revision number of the Unified specification document (1.1).
Table 5 Items in the Syslog File (RFC3164-compliant) (continued) No. Item Description Generated location No output. Related information The location identification name set by the user in the Syslog tab on Edit Audit Log Settings window. No output. No output. Agent information No output. Detailed information Identification of the host sending the request. This information is output when a command is received from the host unless it is FC-SP authentication. No output. No output. No output.
Syslog file format (RFC5424-compliant) Figure 4 syslog file (RFC5424-compliant) Item 21 and 22 are output either one of them in one syslog information. Table 6 Items in the Syslog File (RFC5424-compliant) No. Item Description Priority The priority of an item in the syslog file is determined according to the following formula, enclosed by brackets (< >): Priority = 8 X Facility + Severity Facility is 1 (fixed). Severity depends on the type of log information: • 4: Error or Warning.
Table 6 Items in the Syslog File (RFC5424-compliant) (continued) No. Item Description Process name The process name (-). Message ID The message ID (-). Structured data The structured data (-). Unified specification identification The unified specification identifier (CELFSS). The revision number of the unified specification document (1.1). Message identification The serial number of the syslog header information. Type of audit event The category name of the event.
Table 6 Items in the Syslog File (RFC5424-compliant) (continued) No. Item Description Identification of the application. This information is output when commands are sent from the host. Detailed information The same information contained in the basic information of the audit log file, such as interface, connection number, task name, function name, operation name, parameter, result, and serial number. Task name is output only when a task is registered using Remote Web Console.
2 Using audit logs You can download audit log files and syslog files to Remote Web Console computer or transfer audit log files to FTP servers or syslog servers. Downloading audit log files Download the audit log files to Remote Web Console computer to prevent the old data from being overwritten. It takes from one to five minutes to download the audit log file. WARNING! Do not download the audit log file to the Remote Web Console computer if the audit log is set to be transferred to an FTP server.
Prerequisites • You must have Audit Log Administrator (View Only) or Audit Log Administrator (View & Modify) role to download syslog files. To download the syslog file from SVP: 1. 2. 3. 4. Click Settings > Security > Edit Audit Log Settings. Select Syslog tab on the Edit Audit Log Settings window. Select Transfer Protocol. The output file format is different by the selected protocol. Click Download Syslog. The Specify the Destination dialog box appears.
7. Manually transfer the audit log file to confirm that the FTP server setting is correct. 1. Check that the transfer setting task to the FTP server is complete on the Task window. If the task has not completed, wait until it is complete. 2. Transfer the audit log file to the FTP server manually to confirm that the FTP server setting is correct. For details of manual transfer, see “Manually transferring audit log files to FTP servers” (page 28).
Prerequisites • You must have Audit Log Administrator (View Only) or Audit Log Administrator (View & Modify) role. • Ensure that SVP is connected to the FTP server on a LAN. • Transfer setting to the FTP server must be finished. For how to set, refer to “Automatically transferring audit log files to FTP servers” (page 27). To transfer the audit log file to the FTP server: 1. 2. Click Settings > Security > Edit Audit log Settings. Select FTP tab on the Edit Audit Log Settings window.
2. 3. Enter the Port Number in the primary server setting. Enter client certificate file name, password, and root certificate file name (only when you choose New Syslog Protocol (TLS1.2/RFC5424) at Transfer Protocol). 4. Perform the following if using a secondary syslog server. 1. Click Enable the Secondary Server. 2. Select IPv4 or IPv6 on Server setting and enter the IP address. 3. Enter the Port Number in the secondary server setting. 4.
3 Quick reference This topic provides a quick reference to what each log indicates. Audit Log Functions The following table lists the functions used in audit logging and provides their meanings.
Table 8 Audit Log and Remote Web Console/SVP Operations Function Name Operation Name Corresponding GUI Operation AuditLog Send Test Message Sending the test log to the syslog server in the Edit Audit Log Settings window AuditLog Set FTP Server Changing settings in the Edit Audit Log Settings window AuditLog Set Syslog Server Changing settings in the Edit Audit Log Settings window AuditLog SIM Complete SIM complete in the Edit Audit Log Settings window ACM Add Users Adding a user account to
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation BASE Logout Log out from Remote Web Console or SVP BASE Release HTTP Block Changing settings on the Release HTTP Blocking window BASE Resume Tasks Resuming a task BASE Set CVAE Info Changing information from Command View Advanced Edition Suite BASE Set Up HTTP Block Changing settings on the Set Up HTTP Blocking window BASE Suspend Tasks Suspending a task BASE Unl
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Install Format Stop Maintenance on SVP Install Initialize ORM Value Maintenance on SVP Install Install Maintenance on SVP Install Install CV Maintenance on SVP Install M/F DCR Maintenance on SVP Install Machine Install Date Maintenance on SVP Install Make Volume Maintenance on SVP Install Micro Program Maintenance on SVP Install MP Install Maintenance on S
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Local Replication Split Pairs Splitting pairs for Business Copy, Business Copy Z, or Fast Snap Local Replication Suspend Pairs Suspending pairs for Business Copy or Business Copy Z Maintenance Blockade Maintenance on SVP Maintenance Correction Copy Maintenance on SVP Maintenance DMA Restore Maintenance on SVP Maintenance Drive Interrupt Maintenance on SVP Maintena
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PP KEY PP Apply License Key PP Disable chk PP Enable chk PP Install chk PP Install File chk Update License PROV Add Hosts • Adding the specified host to a host group • Adding a host to the specified host group PROV Add LUN Paths • Mapping an LU path • Creating an alternate LUN path • Copying the selected LUN path PROV Assign MP Blade Assigning an MP blade PROV Block LD
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Edit Host Grps(Mode) Editing host group settings PROV Edit Host Grps(Name) Editing host group settings PROV Edit LDEVs(tier) Relocating tier PROV Edit LDEV Tier Rank Editing the external LDEV tier ranks of pool volumes assigned to a pool PROV Edit MP Blades Editing the MP blade setting PROV Edit Ports(Address) Editing a port address PROV Edit Ports(Attr) Ch
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation PROV Relocate Pool Starting the tier relocation of a pool PROV Remove Hosts Removing a host from a host group PROV Restore LDEVs Restoring an LDEV PROV Restore Pools Restoring a pool PROV Set FCSP Host Creating, changing, or deleting the host authentication information PROV Set FCSP Port Info • Setting port information • Setting default such as user name and secret
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Remote Replication Change RCU Option Changing the remote storage system option for Continuous Access Synchronous, Continuous Access Synchronous Z, Continuous Access Journal, and Continuous Access Journal Z. Remote Replication Clear SIM Clearing SIMs for Continuous Access Synchronous Z and Continuous Access Journal Z.
Table 8 Audit Log and Remote Web Console/SVP Operations (continued) Function Name Operation Name Corresponding GUI Operation Update PFCGrp Update WWN Spreadsheet CflSet End Performing the CFLSET command using External API CflSet Start Ext Stor Add External Volumes Mapping an external volume Ext Stor Assign MP Blade Assigning an MP blade for an external volume Ext Stor Delete ES VOLs Releasing external volume mapping Ext Stor Disconnect ES Paths Disconnecting an external path Ext Stor Disc
Table 9 Function Name and Operation Name Output to Auditlog information file 1 (continued) Function Name Operation Name Corresponding GUI Operation Configuring encryption environment settings Backup Keys Backing up encryption keys on the key management server or backing up encryption keys as a file on the Remote Web Console PC Backup Keys to File Backing up encryption keys as a file on the Remote Web Console PC Backup Keys to Serv Backing up encryption keys on the key management server Create KEK D
Table 10 Function Name and Event Name Output to Auditlog information file 2 Function Name Event Name Output Trigger ENC Change CEK Status • When the encryption environment setting is configured from the initial setting. • When the certificate encryption key is updated. • When the encryption disk adapter is deleted or replaced. Change DEK Status • When the encryption environment setting is configured from the initial setting. • When the encryption environment setting is initialized.
Table 13 Audit Log Lost Output Function Name Event Name Output Trigger AuditLog DKCAuditLog was lost Output when the audit log by the commands that the storage system accepted from the host has been lost.
4 Audit log examples This topic provides examples and descriptions of the audit logs produced by each function and operation that can be performed with Remote Web Console and SVP. For detailed information on the version numbers in log output examples, see Table 4 (page 19). Audit Log Descriptions [AuditLog] Create File Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,,,, [AuditLog],Create File,SVP,Warning,,,Seq.
Example: RFC3164 <14> Jan 4 06:25:18 SVP Storage: CELFSS,1.1,250001,, 2006-01-04T06:25:18.3Z, Storage,SVP,AnomalyEvent,Success,,R800:65307,, Japan-Tokyo,,,,,,,,,,,,SVP,,,[AuditLog],Over Threshold, SVP,Normal end Example: RFC5424 <14>1 2006-01-04T06:25:18.3Z SVP Storage - - - CELFSS,1.
Item Description IPv6: Internet Protocol Version 6, IPv4: Internet Protocol Version 4 OutFlg Whether to transfer the audit log file (audit.log) to the FTP server. Enable: Transfer audit log file. Disable: Do not transfer audit log file. SrvAddr The IP address to which the audit log file is sent. If the setting has not changed, a hyphen (-) is displayed. UserName The user name to login to the FTP server. If the setting has not changed, a hyphen (-) is displayed.
Item Description Secondary: Secondary syslog server Output Indicates whether to transfer the syslog information to the syslog server. It is not output if the setting is not changed. Enable: Syslog information is transferred Disable: Syslog information is not transferred IP Version Indicates the internet protocol version. It is not output if the setting is not changed. IPv6: Internet Protocol Version 6 IPv4: Internet Protocol Version 4 IP Address Indicate the IP address of the syslog server.
Detailed Information Item Description User Name The user name that was added to a user group User Group Name The name of the user group to which the user ID was added Result Result of the operation Normal end: normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: part code, yyyyyy: error code Num. of Users The number of users that were added [ACM] Assign Resource Grps Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description User Group Name The name of a user group All Resource Groups Assigned Indicates whether there is All Resource Groups Assigned setting in the user group Result Result of the operation Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num.
Item Description Local: SVP authentication, External: External authentication User Group Name The name of the user group to which the user ID was added Result Result of the operation Normal end: normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: part code, yyyyyy: error code Num. of Users The number of users that were created [ACM] Create User Grp Example 08xx,YYYY/MM/DD,HH:MM:SS.
[ACM] Delete Users Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx,+00:00,RMI AP,uid=user-name,1, Task Name,[ACM],Delete Users,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{User Name,Result}=[{User01,Normal end},{User02,Normal end}], Num. of Users=2 Detailed Information Item Description User Name The user name that was deleted Result Result of the operation Normal end: normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: part code, yyyyyy: error code Num.
Detailed Information Item Description User Group Name The user group name New User Group Name The user group name that was newly set Result Result of the operation Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num. of User Groups The number of user groups [ACM] Remove Users Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx,+00:00,RMI AP,uid=user-name,1, Task Name,[ACM],Remove Users,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Basic Information for Example 1 Parameter Description Disable Indicates that the External Authentication server is not used Example 2 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ACM],Setup Server,LDAP,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Secondary Server Indicates whether to use a secondary LDAP server Enable: Use the secondary server Disable: Do not use the secondary server Secondary Host Name Indicates the host name of the secondary LDAP server Secondary Port Number Indicates the port number of the secondary LDAP server Num. of Servers The number of external authentication servers that are set Example 3 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description External User Group Mapping Indicates whether to connect an authentication server to an authorization server Enable: Connects an authentication server to an authorization server Disable: Does not connect an authentication server to an authorization server Certificate File Name Indicates the name of certificate file Authentication Protocol Indicates the LDAP protocol to use DNS Lookup Indicates whether to search for the LDAP server using the information registered in the SRV records
Detailed Information for Example 4 Item Description DNS Lookup Displays whether to search for the Kerberos server using the information registered in the SRV records in the DNS server Enable: Performs the search using information registered in the SRV records in the DNS server Disable: Performs the search using the host name and the port number Realm Name Indicates the default realm name Primary Host Name Indicates the host name of the Kerberos server Primary Port Number Indicates the port number o
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{File Name,Result}=[{server.crt,Normal end}, {server.key,Error(xxxx-yyyy)}] Detailed Information Item Description File Name Name of the uploaded file Result Result of the upload operation Normal end: normal end, Error(xxxx-yyyy): Abnormal end xxxx: part code, yyyy: error code [BASE] ControlPanel Backup Example 08xx,YYYY/MM/DD,HH:MM:SS.
[BASE] Create Conf Report Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[BASE],Create Conf Report,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
[BASE] Delete Tasks Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Delete Tasks,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Task Name,Type,User Name,Submission Time,Result} =[{20100101-EditStorageSystem,Edit Storage System,User01, YYYY/MM/DD HH:MM:SS,Normal end},{20100101-CreateLdev, Create LDEV,User02,YYYY/MM/DD HH:MM:SS,Normal end}], Num.
[BASE] Edit Alert Setting Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[BASE],Edit Alert Setting,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Notification Alert=Host Report Detailed Information Item Description Notification Alert Indicates the type of notification Host Report: SIMs with host reports, all: All SIMs [BASE] Edit SIM Syslog Serv Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description IPv6: Internet Protocol Version 6 IPv4: Internet Protocol Version 4 IP Address Indicate the IP address of the syslog server. It is not output if SIMs are not notified by syslog. Port Number Indicates the port number of the LAN while notifying SIMs by syslog. It is not output if SIMs are not notified by syslog. Client Certificate File Name Indicates the client certificate file name. It is not output if the file is not uploaded.
Item Description System Option for Users: Remote Web Console system option Option Bit Indicates the specified option in hexadecimal. Num. of Modes The number of modes [BASE] Enable Auto Delete Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Enable Auto Delete,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
[BASE] Environment Setting Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,0,, [BASE],Environment Setting,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Basic Information Parameter Description Authentication The authentication failed in the issuance of OneTimeKey. OneTimeKey EntryOver The number of OneTimeKeys exceeded the maximum. [BASE] Login Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Login,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [BASE] Logout Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description Task Name Name of the resumed task Type The type of task User Name The ID of the user who resumed the task Submission Time Time when the task was registered Result Result of the operation Normal end: normal end, Error(xxxx-yyyyy): Abnormal end xxxx: part code, yyyyy: error code Num. of Tasks The number of target tasks [BASE] Set CVAE Info Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information item Description HTTP Block Status of the HTTP Block -: disabled, Blocked: enabled Result Result of the HTTP Block setting Normal end: normal end, Error(xxxx-yyyy): Abnormal end xxxx: part code, yyyy: error code [BASE] Suspend Tasks Example 08xx,YYYY/MM/DD,HH:MM.SS.xxx, 00:00,RMI AP,uid=user-name,1,, [BASE],Suspend Tasks,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Mode The type of the operation Delete: Deletion of the certificate for Command View Advanced Edition Suite Set: Registration of the certificate for Command View Advanced Edition Suite [BASE] Update SMIS CrtFiles Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,0,, [BASE],Update SMIS CrtFiles,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{File Name,Result}=[{server.crt,Normal end}, {server.
+LDKC=0x00,CU=0x01 ++{Alias LDEV,Base LDEV}=[{0xFF,0x00}],Num. of Alias LDEVs=1 +Num. of Alias LDEVs=4 Detailed Information Item Description LDKC Indicates LDKC number containing the alias device and the base device CU Indicates CU number containing the alias device and the base device Alias LDEV The alias device number allocated to the CU number indicated in CU of the index Base LDEV The base device number allocated to the CU number indicated in CU of the index Num.
{usr26@co.jp,BCC},{usr27@co.jp,BCC},{-,-},{-,-}, {usr31@co.jp,BCC}],Num. of Accounts=32 Detailed Information Item Description MailServerSetting The specification type of the server HostName: Host name, IP Address: IP address (IPv4 or IPv6) MailServer The SMTP server domain name or IP address. If IP address is specified, the address divided by periods means IPv4 address and the address divided by colons means IPv6 address. SMTP AUTH Indicates whether the SMTP authentication is enabled or disabled.
Basic Information Parameter Description SIM Record of a deleted SIM log SSB Record of a deleted SSB log Reset Record of a deleted Reset log Power Event Record of a deleted Power Event log Detail Record of a deleted Detail log Incident Record of a deleted Incident log HTP Record of a deleted HTP log Diagnosis Record of a deleted Diagnosis log Copy History Record of a deleted Copy History log [Information] ORM Value Example 1: changing the threshold of SAS 08xx,YYYY/MM/DD,HH:MM:SS.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PDEV=HDD000-01 Basic Information Parameter Description Alter Change the threshold of ORM (Online Read Margin) Error Reset Indicates Error Reset Detailed Information Item Description Type The period of time to acquire the result of threshold diagnosis using the read diagnosis function Today: Current day only, 7days: 7 days, Total: Every operating days Read Err. (Unrecovered) The threshold of the Read Error (Unrecovered) Read Err.
Detailed Information Item Description Reference Code The reference code of the SIM whose error and service request are resolved. Num. of Reference Codes The number of SIM reference codes whose error and service request are resolved. [Information] SIM Reporting Option Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Information],SIM Reporting Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Controller hardware error(Recovered,Unrecd.), Drive response late,SAS I/F error Port 0(Unrecd.), SAS I/F error Port 1(Unrecd.),Port 0 error(Unrecd.), Port 1 error(Unrecd.)} ={(150,60),(0,15),(150,30),(150,6),(150,6),0,6,6,12,12} ++PDEV=[HDD000-01,HDD000-02],Num. of PDEVs=2 Example 2 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Information],Threshold Value,Error Reset,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Install Descriptions [Install] Add Host Group Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Add Host Group,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,HostGrpName,Mode,Option[0:31],Option[32:63], Option[64:95],Option[96:127]}= {XX,0xXXX,XXXXXXXXXXXXXXXX,0xXX,0xXXXXXXXX, 0xXXXXXXXX,0xXXXXXXXX,0xXXXXXXXX} ++{WWN,Nickname}=[{0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}, {0xXXXXXXXXXXXXXXXX,XXXXXXXXXXXXXXXX}],Num.
Item Description LUN Indicates the LUN of the logical volume linked to the host group. LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume linked to the host group. Num. of Paths The number of LU paths set. [Install] Add WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Add WWN,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Ver. The version number of the configuration information to be backed up. [Install] Change Host Group Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Change Host Group,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,HostGrpID,HostGrpName} =[{XX,0xXXX,XXXXXXXXXXXXXXXX},{XX,0xXXX,XXXXXXXXXXXXXXXX}], Num.
[Install] Define Config. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Define Config.,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [Install] Delete DKC WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Delete DKC WWN,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Delete WWN} =[{XX,0xXXXXXXXXXXXXXXXX},{XX,0xXXXXXXXXXXXXXXXX}], Num.
Detailed Information Item Description Port The name of the port to which the host group belongs HostGrpID The host group number where the LU path is deleted LUN Indicates LUN where the LU path assignment is cancelled LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the volume where the LU path assignment is cancelled Num. of Paths The number of LU paths deleted [Install] Delete WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.
[Install] FlashDrive ORM Value Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],FlashDrive ORM Value,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description PG The parity group number E1-1: In case of an external volume V1-1: In case of a virtual volume X1-1: In case of a Thin Provisioning volume Num. of PGs The number of parity groups LDEV The LDKC number, the CU number, and the LDEV number Num. of LDEVs The number of LDEVs [Install] Format Stop This log information is output when the format process is suspended. Example 08xx,YYYY/MM/DD,HH:MM:SS.
{3D,Target,Auto,0x00:0x00-0x00:0xFE}, {5D,Target,Auto,0x00:0x00-0x00:0xFE}, {7D,Target,Auto,0x00:0x00-0x00:0xFE}], Num.
Example 2: installing additional DKAs 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Install,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{DKA,Kind}=[{DKA-1PB,DKA (4Port)},{DKA-1PH,DKA (4Port)}, {DKA-2PB,DKA (4Port)},{DKA-2PH,DKA (4Port}],Num. of DKAs=4 Detailed Information for Example 2 Item Description DKA The Disk Adapter mounting location Kind The type of Disk Adapter Num.
Item Description PG The parity group number RAID Level The RAID Level Drive Type The type of the drive Emulation The emulation type Concatenation The RAID concatenated parity group number. A hyphen (-) is indicated when the parity group is not RAID concatenated.
Item Description Size The capacity of cache memory Num. of CMs The number of cache memory BKM The mounting location for BKM Type The type of BKM Size The size of CFM Num. of BKMs The number of BKMs DCR available size The capacity of Cache Residency CLPR The CLPR number Cache size The capacity of the cache memory allocated to CLPR DCR size The capacity of Cache Residency allocated to CLPR Extent Number The number of extents allocated to CLPR Num.
Item Description CMG The capacity of CMG Size The capacity of cache memory Num. of CMs The number of cache memory BKM The mounting location for BKM Type BKM The type of BKM Size CFM The size of CFM Num. of BKMs The number of BKMs DCR available size The capacity of Cache Residency CLPR The CLPR number Cache size The capacity of the cache memory allocated to CLPR DCR size The capacity of the Cache Residency allocated to CLPR Extent Number The number of extents allocated to CLPR Num.
Detailed Information for Example 6 Item Description SVP The installed location of the SVP IPAddress IP address in the SVP Subnet Mask The subnet mask in the SVP Use Duplex The duplex status of the SVP. Valid or Invalid will appear. SVP Kind The kind of the duplex status. Master SVP or Standby SVP will appear. IPv4 The status of IPv4 settings. Valid or Invalid will appear. IPv6 The status of IPv6 settings. Valid or Invalid will appear.
Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Install CV,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PG,LDKC:CU:LDEV,Slot,Emulation,Size,Unit,SSID,MPB} =[{1-1,0x00:0x00:0x00,-,OPEN-V,10000,LBA,0x0005,Auto}], Num. of LDEVs=1 Basic Information Parameter Description Non Format Unformatted Install CV. Progress Close The window that shows the progress of LDEV formatting has closed. Quick Format Quick Format is selected.
[Install] Make Volume This logged information indicates that formatting the volume was requested but not completed. If the operation does not require formatting, this logged information indicates that the volume was created. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Make Volume,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PG,LDKC:CU:LDEV,Slot,Emulation,Size,Unit,SSID,MPB} =[{1-1,0x00:0x14:0x00,-,OPEN-V,205440,LBA,0x0005,Auto}], Num.
+{Micro Kind, Old Ver, New Ver} =[{DKCMAIN, 7000320000,7000320001}, {SVP, 70003200, 70003201}],Num. of Kinds=2 Detailed Information Item Description Micro Media The media which the microcode to be exchanged is stored (CD-ROM:CD-ROM, HD: Hard Disk, HD Backup: HDD Backup (version down), or Remote: Remote transfer). Exchange How The method to exchange the microcode. Online: Exchanging the microcode online, Offline: Exchanging the microcode offline. Reboot Grp.
Detailed Information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number of the logical volume where Cache Residency is set. Define The status of Cache Residency Set: set, Delete: cancel Mode The Cache Residency. mode Indicates a dash (-) when Define is Delete. Bind: Bind mode, Priority: Priority mode Prestaging Indicates whether the Prestaging mode set is enabled or disabled Indicates a dash (-) when Define is Delete.
[Install] Remove Example 1: removing a channel adapter (CHA) 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Remove,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{CHA,Kind} =[{CHA-1PC,16FC8(Fibre )},{CHA-2PU,16FC8(Fibre )}], Num. of CHAs=2 Detailed Information for Example 1 Item Description CHA The Channel Adapter mounting location Kind The kind of PCB mounted Num.
Item Description B4 The B4 number SPARE The spare drive number Num. of SPAREs The number of spare drives Example 4: removing a cache memory module 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Remove,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{CM,CMG,Size} =[{1CA/2CA,CM16G x 2,65536},{1CB/2CB,CM16G x 2,65536}, {1CE/2CG,CM16G x 2,65536},{1CF/2CH,CM16G x 2,65536}],Num.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{MPB,Auto LDEV Assignment} =[{MPB-1MB,Disable},{MPB-2MB,Enable},{MPB-1MD,Enable}, {MPB-2MD,Enable}],Num. of MPBs=4 +{CM,CMG,Size}=[{1CC/2CC,CM16G x 2,0}],Num. of CMs=1 +{BKM,Type,Size}=[{1BC/2BC,----------,0}],Num. of BKMs=1 +DCR available size=1024 +{CLPR,Cache size,DCR size,Extent Number} =[{CLPR0,177664,0,16384}],Num.
Basic Information Parameter Description SVP Indicates a change in the IP address of the SVP SVP and DKC Indicates a change in the IP address of the SVP and the DKC Detailed Information for Example 6 Item Description SVP The installed location of the SVP IPAddress IP address in the SVP Subnet Mask The subnet mask in the SVP Use Duplex The duplex status of the SVP. Valid or Invalid will appear. SVP Kind The kind of the duplex status. Master SVP or Standby SVP will appear.
[Install] Restore Config. The audit log files in Example 1 and Example 2 are output when the Restore Configuration operation is performed by using an SVP. However, the audit log file in Example 2 is not output if the Restore Configuration operation is suspended before the Define Configuration and Install operation is performed. Example 1 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Restore Config,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{New Ver.
[Install] Set Channel Speed Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set Channel Speed,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Speed(Gbps)}=[{XX,1},{XX,2},{XX,Auto}], Num. of Ports=3 Detailed Information Item Description Port The name of the port on which the channel speed is set. Speed(Gbps) The channel speed set 1: 1 Gbps, 2: 2 Gbps, 4: 4 Gbps, 8: 8 Gbps, Auto: Auto mode. Num.
[Install] Set DevGrpDef Example 08xx, YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set DevGrpDef,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,DevGrpDef}=[{0xXX:0xXX:0xXX,Enable}], Num. of LDEVs=1 Detailed Information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the volume where the device group definition is specified. UserAuth Indicates whether the device group definition is enabled or disabled.
Item Description Connection The connecting mode of the Fabric switch selected FC-AL: FC-AL is selected, P-to-P: P-to-P is selected Num. of Ports The number of ports where the topology of Fibre Channel is set [Install] Set Host Mode Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set Host Mode,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Basic Information Parameter Description SVP The SVP IP address change SVP and DKC The IP address change of the SVP and DKC Detailed Information Item Description IPAddress The SVP IP address Subnet Mask The subnet mask in SVP Use Duplex Indicates whether the Duplex setting in SVP is valid or invalid Valid: Valid, Invalid: Invalid SVP Kind The kind of duplicated SVP Master SVP: Master SVP, Standby SVP: Standby SVP.
[Install] Set Subsystem Time Example 1: The case of TOD Change 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set Subsystem Time,TOD Change,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Time=YYYY/MM/DD HH:mm:SS Example 2: The case of Synchro. Infor. For IPv4 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Set Subsystem Time,Synchro. Infor.,Normal end, from=xxx:xxx:xxx:xxx,,Seq.=xxxxxxxxxx +{Use Synchro.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,UserAuth}=[{0xXX:0xXX:0xXX,Enable}], Num. of LDEVs=1 Detailed Information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the volume where the user authentication is specified. UserAuth Indicates whether the user authentication is enabled or disabled. Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the user authentication is set.
Item Description LPR The LPR name Cache Tuning The level of Cache Tuning Num. of LPRs The number of LPRs Command Control Command Control Mode The local mode number Set The setting status. ON: Set, Off: Release Num. of Modes The number of local modes. Debug Mode Setting executed from the debug window (Set: fix). Note: Only the changed items will be output. [Install] System Tuning Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Num. of SSIDs The number of storage system IDs TPF Enable The status of TPF Function settings ON: Enabled OFF: Disabled Number of MPLs The allocated number of MPLs A hyphen (-) appears if the TPF Enable is OFF. [Install] Update Config Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Install],Update Config,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{New Ver.,Old Ver.
=[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,0,Normal end}, {0xX:0xAA:0xBB,0xY:0xCC:0xDD,1,Error(xxxx-yyyyy)}], Num. of Pairs=2 Example 2: when the copy type is FS 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Create Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
+Copy Type=BC ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,Normal end}, {0xX:0xAA:0xBB,0xYY:0xCC:0xDD,Error(xxxx-yyyyy)}], Num. of Pairs=2 Example 2: when the copy type is FS 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Delete Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Copy Pace Ext. Slower1=Disable, Copy Pace Ext. Slower2=Disable,Copy Pace Ext. None=Disable, (snip),Reserve32=Disable Detailed Information Item Description Copy Type The program product name for this operation BC: Business Copy, BC Z: Business Copy Z Swap & Freeze Indicates whether the Swap & Freeze option is enabled or disabled. Enable: Enabled, Disable: Disabled Host I/O Performance Indicates whether the Host I/O Performance option is enabled or disabled.
[Local Replication] Release Reserved CTG Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Release Reserved CTG,,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=BC Z ++{CTG,Result}=[{0x01,Normal end},{0x02,Normal end}, {0x03,Normal end}],Num.
{0xX:0xAA:0xBB,0xY:0xCC:0xDD,Error(xxxx-yyyyy)}], Num. of Pairs=2 Example 2: when the copy type is FS 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Local Replication],Resync Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=FS,Resync Type=Reverse Copy ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,,Normal end}, {0xX:0xAA:0xBB,,1,Error(xxxx-yyyyy)}],Num.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=FS ++{P-VOL(LDKC:CU:LDEV),S-VOL(LDKC:CU:LDEV),MU,Result} =[{0xXX:0xAA:0xBB,0xYY:0xCC:0xDD,,Normal end}, {0xXX:0xAA:0xBB,,1,Error(xxxx-yyyyy)}],Num.
Item Description S-VOL (LDKC:CU:LDEV) The LDKC number, the CU number and the LDEV number of the secondary volume in the suspended pair Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Pairs The number of suspended pairs Maintenance Descriptions [Maintenance] Blockade Example 1: blocking a PCB 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description PDEV The mounting location of the PDEV (physical device) [Maintenance] DMA Restore Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],DMA Restore,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +DMA=[DMA-10],Num. of DMAs=1 Detailed Information Item Description DMA The specified DMA Num. of DMAs The number of specified DMAs [Maintenance] Drive Interrupt Example 08xx,YYYY/MM/DD,HH:MM:SS.
Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Format,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PG=[1-1],Num. of PGs=1 Detailed Information Item Description PG The parity group number E1-1: In case of an external volume V1-1:In case of a virtual volume X1-1: In case of a Thin Provisioning volume Num. of PGs The number of parity groups LDEV The LDKC number, the CU number, and the LDEV number Num.
Detailed Information Item Description MP The identity of the microprocessor Num. of MPs The number of microprocessors that were restored [Maintenance] PCB Restore Example 08xx,YYYY/MM/DD,HH:MM:SS:xxx, 00:00,SVP,uid=maintenance,0,, [Maintenance],PCB Restore,,Error, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PCB=[CACHE-2CC],Num. of PCBs=1 Detailed Information Item Description PCB The PCB. Num.
Detailed Information Item Description PG The parity group number E1-1: In case of an external volume V1-1: In case of a virtual volume X1-1: In case of a Thin Provisioning volume Num. of PGs The number of parity groups LDEV The LDKC number, the CU number, and the LDEV number Num. of LDEVs The number of LDEVs. [Maintenance] Replace Example 1: replacing parts 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description PCB The mounting location of the PCB, (Channel Adapter (CHA), Disk Adapter (DKA), cache memory, MPB, or BKM) to be replaced. Failed When replacing multiple PCBs and some of the PCBs to be replaced had failures, the mounting locations of the failed PCBs are indicated. In such case, "Warning" is output as the result of the process. Note: This information is not output when there are no failed PCBs. Num.
[Maintenance] Restore Data Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Restore Data,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PDEV=HDD000-00 Detailed Information Item Description PDEV The mounting location of the PDEV [Maintenance] Set Battery Life This log information is output when Battery Life Warning SIM is set at the time of replacing a CM or a battery. Example 08xx,YYYY/MM/DD,HH:MM:SS.
[Maintenance] Spare Disk Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Spare Disk,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PDEV=HDD000-00 Detailed Information Item Description PDEV The mounting location of the PDEV [Maintenance] Switch SVP This logged information indicates that the Switch SVP operation was only requested but not completed. Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description PCB The mounting location of the PCB to be changed Num. of PCBs The number of the PCBs to be changed Type The type of the PCB DKA (4Port ): DKA, EDKA (4Port ): Encryption DKA Note: In the actual log file, there are two spaces output between "DKA" and "(4Port)". [Maintenance] Verify Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Maintenance],Verify,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PG=[1-1],Num.
Monitor Descriptions [Monitor] Threshold Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,uid=user-name,1,, [Monitor],Threshold,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume (for a mainframe system) where the setting information of Cache Residency cache is canceled. Start CC-HH The starting cylinder number (CC) and the starting head number (HH) of the cancelled data End CC-HH The ending cylinder number (CC) and the ending head number (HH). This number is output when the ending cylinder and ending head are specified for the cancelled data. Num.
Detailed Information Item Description LDKC:CU The ID of the monitored CU The logical DKC number and the CU number are separated by colons and arranged in this order. [Perf Mon] Edit Monitoring SW Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Perf Mon],Edit Monitoring SW, Enable 60sec,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
++Port=[XX],Num. of Ports=1, -Num. of WWNs=1 Detailed Information Item Description Mode The setting mode of WWN Add WWN: Addition of HBA WWN, Delete WWN: Deletion of HBA WWN HBA WWN The HBA WWN WWN Name The WWN name Port The name of a target port Num. of Ports The number of target ports for the added or deleted WWN Num. of WWNs The number of added or deleted WWNs [Perf Mon] Set M/F DCR Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume (for an open system) where the setting information of Cache Residency cache is added or changed. Mode The setting mode of Cache Residency cache Bind: Bind, Priority: Priority Prestaging The prestaging target.
Detailed Information This log information is output when the setting task of the program product (Install/Remove or Enable/Disable Licenses) is complete. The information of all of the program products is sent to the storage system, so the names of all of these appear in the log. Item Description P.P.Name The program product name Result The check result of the program product Normal end: Normal end, Error(xxxxx-yyyyyy): Abnormal end xxxxx: Part code, yyyyyy: Error code Num.
Item Description xxxxx: Part code, yyyyyy: Error code Num. of PPs The number of program products to be enabled [PP KEY] PP Install chk This log information merely indicates that the GUI operation of installing a program product is complete, and it does not necessarily mean that the program product is actually installed. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PP KEY],PP Install chk,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
[PP KEY] PP Removal chk This log information merely indicates that the GUI operation of uninstalling a program product is complete, and it does not necessarily mean that the program product is actually uninstalled. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [PP KEY],PP Removal chk,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{P.P.Name,Result}=[{JAVA API,Normal end}],Num. of PPs=1 Detailed Information Item Description P.P.
Detailed Information Item Description Port The name of the port to which the host group belongs HostGrpID The host group number where the host is registered WWN Indicates WWN of the host bus adapter for the host registered in the host group. WWN is a 16-digit number in the hexadecimal format. Nickname The nickname of the host bus adapter for the host registered in the host group Num. of WWNs The number of registered hosts (WWN) [PROV] Add LUN Paths Example 08xx,YYYY/MM/DD,HH:MM:SS.
[PROV] Block LDEVs Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Block LDEVs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +LDKC:CU:LDEV=[0x00:0x00:0x01,0x00:0x00:0x02,0x00:0x00:0x03, 0x00:0x00:0x04,0x00:0x00:0x05,0x00:0x00:0x06,0x00:0x00:0x07, 0x00:0x00:0x08,0x00:0x00:0x09,0x00:0x00:0x0A], Num. of LDEVs=10 Detailed Information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number Num.
[PROV] Create LDEVs Example 1: Creating internal volumes or external volumes 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create LDEVs,Basic,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PG,LDKC:CU:LDEV,Start LBA,Emulation,Size,Unit,MP Blade ID} =[{XX-XX,0xXX:0xXX:0xXX,XXXXXXXX,OPEN-V,XXXXXXXX,KB,Auto}, {XX-XX,0xXX:0xXX:0xXX,XXXXXXXX,OPEN-V,XXXXXXXX,KB,0xX}], Num.
Example 3: Creating THP V-VOLs 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create LDEVs,Thin Provisioning,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,LDKC:CU:LDEV,LDEVCapa(blocks),Emulation,CLPR,SSID, MP Blade ID,Attribute,Result}=[{1,0x00:0x00:0x00,96000,OPEN-V, 0,0x0004,Auto,-,Normal end},{1,0x00:0x01:0x00,96000,OPEN-V, 0,0x0005,Auto,-,Normal end}],Num.
Detailed Information Item Description VDKC-Box ID The number of the VDKC-Box to which the created resource group belongs. A hyphen (-) is output when the creating operation failed. Resource Group ID The number of the created resource group.
[PROV] Create/Expand Pools Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Create/Expand Pools,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,Pool Type,Multi Tier Pool,Warning Threshold(%), Depletion Threshold(%),Subscription Limit(%),Tier Management, Cycle Time,Monitoring Period,Monitoring Mode,Relocation Speed, Pool Result} =[{1,Thin Provisioning,Enable,20,70,100,Auto,24,00:00-23:59, Continuous Mode,3,Normal end}],Num.
Item Description If Multi Tier Pool is anything other than Enable, a hyphen (-) is output. Relocation Speed The relocation speed 1: Slowest, 2: Slower, 3: Normal, 4: Faster, 5: Fastest Pool Result The result of pool creation or expansion Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed xxxx: Part code, yyyyy: Error code Num.
Basic Information for Example 1 Parameter Description Basic Delete LDEVs was done to basic volumes External Delete LDEVs was done to external volumes Basic/External Delete LDEVs was done to both basic volumes and external volumes Detailed Information for Example 1 Item Description PG The parity group number. An E at the beginning of a parity group number designates an external volume is present in that parity group. LDKC:CU:LDEV The LDKC, CU, and LDEV numbers Num.
Item Description where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of deleted V-Vols [PROV] Delete Login WWNs Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Delete Login WWNs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Delete WWN} =[{XX,0xXXXXXXXXXXXXXXXX},{XX,0xXXXXXXXXXXXXXXXX}], Num.
Detailed Information Item Description VDKC-Box ID The number of the VDKC-Box to which the deleted resource group belongs Resource Group ID The number of the deleted resource group Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end xxxx: Part code, yyyyy: Error code Num. of Resource Groups The number of deleted resource groups [PROV] Delete VDKC-Box Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description LDKC:CU:LDEV The LDKC, CU, and LDEV numbers of the logical volume where the command device authentication setting is changed UserAuth Indicates whether the command device authentication setting is enabled or disabled. Disable or Enable will appear. Num. of LDEVs The number of logical volumes where the command device authentication setting is changed [PROV] Edit Cmd Dev(DevGrp) Example 08xx,YYYY/MM/DD,HH:MM:SS.
[PROV] Edit Command Devices Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Command Devices,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV,CommandDev}=[{0xXX:0xXX:0xXX,Disable}, {0xXX:0xXX:0xXX,Enable}],Num.
Item Description Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of logical volumes where the attribute has been set *When bit 5, 6, and 7 are all 0 (zero), Read/Write has been set. [PROV] Edit Host Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Host,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Option[64:95] The following tables show the output values corresponding to the host mode options. Option[96:127] See the HP XP7 Provisioning for Open Systems User Guide for the meaning of the host mode options. Num. of Host Groups The number of host groups that the host mode setting is changed.
Table 15 Host mode option 32 to 63 and output contents of Option[32:63] (continued) Host mode option Value of Option[32:63] Host mode option Value of Option[32:63] 44 0x00080000 60 0x00000008 45 0x00040000 61 0x00000004 46 0x00020000 62 0x00000002 47 0x00010000 63 0x00000001 Table 16 Host mode option 64 to 95 and output contents of Option[64:95] Host mode option Value of Option[64:95] Host mode option Value of Option[64:95] 64 0x80000000 80 0x00008000 65 0x40000000 81 0x000040
Table 17 Host mode option 96 to 127 and output contents of Option[96:127] (continued) Host mode option Value of Option[96:127] Host mode option Value of Option[96:127] 107 0x00100000 123 0x00000010 108 0x00080000 124 0x00000008 109 0x00040000 125 0x00000004 110 0x00020000 126 0x00000002 111 0x00010000 127 0x00000001 When more than one option is set, a logical sum of their values is output.
[PROV] Edit LDEV Tier Rank Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit LDEV Tier Rank,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,Pool Result}=[{1,Normal end}],Num. of Pools=1 ++{LDKC:CU:LDEV,External LDEV Tier Rank,LDEV Result} =[{0x00:0x00:0x00,Middle/Internal,Normal end}, {0x00:0x00:0x01,Middle/Internal,Normal end}, {0x00:0x00:0x02,Middle/Internal,Normal end}],Num.
Item Description Enable or Disable will appear Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of MP Blades The number of specified MP Blades (1 to 8) [PROV] Edit Ports(Address) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Ports(Address),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Fibre Addr.}=[{XX,1},{XX,126}],Num.
Table 18 Addresses of Fibre Channel Port (continued) Value Address* Value Address* Value Address* Value Address* 17 CD (16) 49 98 (48) 81 55 (80) 113 25 (112) 18 CC (17) 50 97 (49) 82 54 (81) 114 23 (113) 19 CB (18) 51 90 (50) 83 53 (82) 115 1F (114) 20 CA (19) 52 8F (51) 84 52 (83) 116 1E (115) 21 C9 (20) 53 88 (52) 85 51 (84) 117 1D (116) 22 C7 (21) 54 84 (53) 86 4E (85) 118 1B (117) 23 C6 (22) 55 82 (54) 87 4D (86) 119 18 (118) 24 C5 (23)
Detailed Information Item Description Port The name of the port where the LUN security setting is changed Switch Indicates whether the LUN security setting is enabled or disabled. Disable or Enable is output Num. of Ports The number of ports where the LUN security setting is changed [PROV] Edit Ports(Speed) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Edit Ports(Speed),,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{VDKC-Box ID,Resource Group ID,Resource Group Name,Result} =[{0,1,RSG1,Normal end}],Num.
Item Description Tier1 Min(%) The lower limit threshold value for the Tier1 The threshold value is displayed in the range 0 to 100. The unit is percent (%). This is output when the lower limit threshold value for the Tier1 is set. Tier3 Max(%) The upper limit threshold value for the Tier3 The threshold value is displayed in the range 0 to 100. The unit is percent (%). This is output when the upper limit threshold value for the Tier3 is set.
+{Pool ID,LDKC:CU:LDEV,Tiering Policy ID, New Page Assignment Tier,Relocation Priority,Result} =[{0,0x00:0x00:0x00,1,Middle,Default,Normal end}], Num. of VOLs=1 Detailed Information Item Description Pool ID The pool ID of a pool associated with the V-VOL for Thin Provisioning to which Tiering policy is set LDKC:CU:LDEV The LDKC number, CU number, and LDEV number of the V-VOL for Thin Provisioning Tiering Policy ID The Tiering Policy ID This is output when the tiering policy is set.
Item Description Thin Provisioning: Thin Provisioning, Fast Snap: Fast Snap Multi Tier Pool Indicates whether the multi-tier mode of the pool is enabled or disabled. Enable: Enabled, Disable: Disabled This item is output only when "Command" is "Change Tier". If Pool Type is Fast Snap, a hyphen (-) is output. Warning Threshold(%) The warning threshold of the usage rate of the pool in percent (%). This item is output only when "Command" is "Change".
Item Description Buffer Space for New page assignment(%) The capacity rate of buffer space for new page assignment The unit is percent (%) This value is output only when the command is Change Tier Buffer Space for Tier relocation(%) The capacity rate of buffer space for Tier relocation The unit is percent (%) This value is output only when the command is Change Tier Tier Result The result of Tier operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed where xxxx:
Item Description Capacity The capacity of the V-VOL after expanding in LBAs Num. of VOLs The number of expanded V-VOLs [PROV] Format LDEVs The logged information indicates that the Format operation was only requested but not completed. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Format LDEVs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
0x00:0x00:0x06,0x00:0x00:0x07,0x00:0x00:0x08, 0x00:0x00:0x09,0x00:0x00:0x0A],Num. of LDEVs=10 Detailed Information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number Num. of LDEVs The number of LDEVs to be formatted [PROV] Initialize Pools Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Initialize Pools,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [PROV] LDEV Name Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description Pool ID The pool ID of a pool where the performance monitoring started Result The result of starting the performance monitoring of pools Normal end: Normal end, Error(xxxx-yyyyy):Abnormal end, Not Execute: Not executed where xxxx: Part code, yyyyy: Error code Num. of Pools The number of pools where the performance monitoring started [PROV] Move Resources Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Error(xxxx-yyyyy): Abnormal end, where xxxx: Part code, yyyyy: Error code Num. of PGs The number of moved parity groups Port The name of a moved port PortResult The result of the port Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, where xxxx: Part code, yyyyy: Error code Num.
Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Reclaim Zero Pages,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{LDKC:CU:LDEV} =[{0x00:0x00:0x00},{0x00:0x00:0x01},{0x00:0x00:0x02}], Num. of VOLs = 3 Detailed Information Item Description LDKC:CU:LDEV The LDKC number, the CU number, and the LDEV number of the LDEV where zero pages are reclaimed Num.
Detailed Information Item Description Pool ID The pool ID of a pool where the tier relocation was performed Result The result of relocating the tier of pools Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed where xxxx: Part code, yyyyy: Error code Num. of Pools The number of pools where the tier relocation was performed [PROV] Remove Hosts Example 08xx,YYYY/MM/DD,HH:MM:SS.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,Result} =[{1,Normal end},{2,Normal end},{128,Normal end}], Num. of Pools=3 Detailed Information Item Description Pool ID The restored pool ID Result The result of the operation: Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed where xxxx: Part code, yyyyy: Error code Num. of Pools The number of restored pools [PROV] Set FCSP Host Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description Port The name of the port where authentication parameter has been set Auth_TOV The time to execute authentication after the failure of port authentication. The unit is second. Reject Time The period of time to reject authentication when port authentication have failed. The unit is minute. Reject Count The number of authentication failures allowed before port authentication is rejected Num.
Detailed Information Item Description Port The name of the port that includes the host group where authentication parameter has been set HostGrpID The number of the host group where authentication has been set Switch The setting status whether to execute authentication by host group. Disable: Do not authenticate, Enable: Authenticate DH Group Not used (fixed to 0) UserName The user name of the host group Num.
[PROV] Set SSID Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[PROV],Set SSID,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{SSID,LDKC:CU:LDEV} =[{0xXXXX,0xXX:0xXX:0xXX},{0xXXXX,0xXX:0xXX:0xXX}], Num. of SSIDs=2 Detailed Information Item Description SSID The SSID number LDKC:CU:LDEV The LDKC, CU, and LDEV numbers Num. of SSIDs The number of SSIDs [PROV] Set Virtual LDEV Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Virtual Attribute The attribute of the virtual LDEV CVS: CVS attribute, -: No attribute Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy):Abnormal end where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of LDEVs that is mapped the virtual information [PROV] Shrink Pool This log information does not indicate the completion of shrinking processing but the completion of shrinking operation. Example 08xx,YYYY/MM/DD,HH:MM:SS.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,Result}=[{1,Normal end}],Num. of Pools = 1 Detailed Information Item Description Pool ID The pool ID of a pool where the performance monitoring stopped Result The result of stopping the tier relocating of pools Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not Executed where xxxx:Part code, yyyyy: Error code Num.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Pool ID,Result}=[{1,Normal end},{2,Normal end}], Num. of Pools = 2 Detailed Information Item Description Pool ID The pool ID of the pool where shrinking is stopped Result The result of the stopping shrinking operation Normal end: Normal end Not Execute: Not executed Error(xxxxx-xxxxxxx): Abnormal end where xxxxx-xxxxxxx indicates error codes. Num.
Item Description ON: PSON operation, OFF: PSOFF operation. [Remote Maintenance] Reboot MP Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RM AP,,,, [Remote maintenance],Reboot MP,,Normal end,,,Seq.=xxxxxxxxxx +MP=MP00-1MA Detailed Information Item Description MP Indicates the name of MP to be rebooted [Remote Maintenance] Reboot Port Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RM AP,,,, [Remote Maintenance],Reboot Port,,Normal end,,,Seq.
+{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID,Result} ={99999,0x00,0x00,Default,6,Nomal end} ++{MCU Port,RCU Port} =[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H}], Num. of Port Pairs=7 (Snip) +{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID,Result} ={99998,0x00,0x00,Default,6,Nomal end} ++{MCU Port,RCU Port} =[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H}], Num. of Port Pairs=7 +Num. of RCUs=xx Example 2: when not using CU Free 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code MCU The CU number of the connected CU RCU The CU number of the paired CU SSID The SSID MCU Port The port number of MCU RCU Port The port number of RCU Num. of Port Pairs The number of port pairs set Num. of RCUs The number of RCUs set [Remote Replication] Add RCU Example 1: when using CU Free 08xx,YYYY/MM/DD,HH:MM:SS.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID,Min.Path, MIH Time(s),Round Trip Time(ms),FREEZE,Result} ={99998,0x00,0x00,Default,6,08,015,001,Disable,Nomal end} ++{MCU Port,RCU Port} =[{1E,3E},{5E,7E},{1F,3F},{5F,7F},{1G,3G},{5G,7G},{1H,3H}, {5H,7H}],Num. of Port Pairs=8 (Snip) +{S/N,MCU LDKC,MCU,RCU LDKC,RCU,SSID,Controller ID,Min.
[Remote Replication] Change JNL Option Example 1: when the copy type is Cnt Ac-J 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Change JNL Option,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=Cnt Ac-J +{LDKC,JNL,Data Overflow Watch(s),Inflow Control, Use of Cache,Result} =[{0x00,0x001,20,Yes,Not Use,Normal end}, {0x00,0x002,20,No,Use,Normal end}],Num. of JNLs=2 Example 2: when the copy type is Cnt Ac-J Z 08xx,YYYY/MM/DD,HH:MM:SS.
+Copy Type=Cnt Ac-J +{LDKC,JNL,MirrorID,Copy Pace,Path Watch Time, Forward Path Watch Time,Transfer Speed(Mbps), Delta resync Failure,Result} =[{0x00,0x001,0x00,Medium,12(hour),Yes,100,Entire,Normal end}, {0x00,0x002,0x00,Low,1(day),No,10,None,Normal end}], Num.
+{S/N,MCU LDKC,MCU,RCU LDKC,SSID,Controller ID,Min.Path, MIH Time(s),Round Trip Time(ms),FREEZE,Result} ={99998,0x00,0x3F,0x00,0x0004,6,08,015,001,Disable,Nomal end} (Snip) +{S/N,MCU LDKC,MCU,RCU LDKC,SSID,Controller ID,Min.Path, MIH Time(s),Round Trip Time(ms),FREEZE,Result} ={99999,0x00,0x3F,0x00,0x0004,6,08,015,001,Disable,Nomal end} +Num. of RCUs=xx Example 3: when using CU Free and not using CU Free coexist 08xx,YYYY/MM/DD,HH:MM:SS.
[Remote Replication] Clear SIM Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Clear SIM,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [Remote Replication] Create Pairs Example 1: when the copy type is Cnt Ac-S 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Create Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of create pairs Example 2: when the copy type is Cnt Ac-S Z 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Create Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description TS Indicates whether to transfer the host I/O time stamp to the secondary volume when creating a pair. This value is output only when a synchronous pair is created. Enable: Transfer, Disable: Not transfer Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of create pairs Example 3: when the copy type is Cnt Ac-J 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of created pairs Example 4: when the copy type is Cnt Ac-J Z 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Create Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of created pairs [Remote Replication] Delete Cmd.Dev Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Delete Cmd.Dev,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Example 2: when the copy type is Cnt Ac-S Z 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Delete Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=Cnt Ac-S Z,{VOL(LDKC:CU:LDEV),PairVOL(LDEV), Type,Mode,Result} =[{0x00:0x00:0x00,0xFD,P-VOL,Normal,Normal end}, {0x00:0x00:0x01,0xFE,P-VOL,Normal,Normal end}, {0x00:0x00:0x02,0xFF,P-VOL,Normal,Normal end},(Snip)-(Snip)], Num.
Item Description CTRLID The controller ID of the RCU 7: XP7, 6: P9500, 5: XP24000/XP20000 Disk Array, 19: HUS VM Type The volume type of the deleted volume P-VOL: Primary volume, S-VOL: Secondary volume Range The delete range Mirror: Mirror range, LU: LU range, Volume: Volume range Delete Mode The delete mode Normal: Normal mode, Force: Force mode Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num.
Item Description Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of deleted pairs [Remote Replication] Delete path Example 1: when using CU Free 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Delete Path,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{S/N,MCU LDKC,RCU LDKC,Path Gr.
Detailed Information Item Description S/N The serial number of the RCU on which a path is deleted MCU LDKC The LDKC number of the connected LDKC RCU LDKC The LDKC number of the paired LDKC Path Gr.ID The path group ID of the deleted path. When the path group ID is default setting, "Default" is output.
+{S/N,MCU LDKC,RCU LDKC,Path Gr.ID,Controller ID,Result} ={99999,0x00,0x00,Default,6,Nomal end} (Snip) +{S/N,MCU LDKC,MCU,RCU LDKC,SSID,Result} ={99998,0x00,0x3F,0x00,0x0004,Nomal end} +Num. of RCUs=xx Detailed Information Item Description S/N The serial number of the deleted RCU MCU LDKC The LDKC number of the connected LDKC RCU LDKC The LDKC number of the paired LDKC Path Gr.ID The path group ID of the deleted RCU. When the path group ID is default setting, "Default" is output.
Path Blockade Watch(s),Path Blockade SIM Watch(s), Service SIM,Switch} ={128,Enable,45,070,Not Report,-} +{LDKC,CU,Service SIM,PPRC Support,Max Initial Copy} =[{0x00,0x00,Not Report,Yes,04}, {0x00,0x01,Not Report,Yes,04}, {0x00,0x02,Not Report,Yes,04}, {0x00,0x03,Not Report,Yes,04}, {0x00,0x04,Not Report,Yes,04},(Snip)-(Snip)], Num. of CUs=255 Example 4: Editing remote replication function switch 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description CU The CU number of the connected CU Service SIM Indicates whether to report the remote replication-related SIM Report, Not Report If this is not a subject to change, a hyphen (-) is displayed. If any one of Service SIM, PPRC Support, and Max Initial Copy is changed, this will be the subject to change. PPRC Support Indicates whether the host supports PPRC Yes: Support, No: Not support If this is not a subject to change, a hyphen (-) is displayed.
Item Description Report, Not report Num. of CUs The number of CUs on which the setting is changed Note: Only the changed items are output. [Remote Replication] Edit Pair Options Example 1: when the copy type is Cnt Ac-S 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Edit Pair Options,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description CFW Indicates whether the setting to copy the CFW (Cache Fast Write) data to the secondary volume is enabled or not. Only P-VOL: Copy to primary volume only is enabled Copy to S-VOL: Copy to primary and secondary volume is enabled Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num.
Only P-VOL,Normal end}, {0x00:0x00:0x02,0x00:0x20:0x02,0x03,0x001,0x002,Volume, Only P-VOL,Normal end}], Num.
[Remote Replication] Journal Vol Example 1: Adding journal volumes when the copy type is Cnt Ac-J 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Journal Vol,Add,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=Cnt Ac-J +{LDKC,JNL,2DC Cascade,Owner}={0x00,0x001,Disable,0x00} ++{LDKC:CU:LDEV,Result} =[{0x00:0xD7:0x01,Normal end}],Num.
Item Description Num. of LDEVs The number of LDEVs set for the journal Num. of JNLs The number of journals Example 3: Adding journal volumes when the copy type is Cnt Ac-J Z 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Journal Vol,Add,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=Cnt Ac-J Z +{LDKC,JNL,Timer Type,Owner}={0x00,0x001,System,0x00} ++{LDKC:CU:LDEV,Result} =[{0x00:0xD7:0x01,Normal end}],Num.
Item Description Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of LDEVs The number of LDEVs set for the journal Num. of JNLs The number of journals Example 5: Deleting journals when the copy type is Cnt Ac-J or Cnt Ac-J Z 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Journal Vol,Delete JNL,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Basic Information Parameter Description Assign The remote command device is assigned. Release The remote command device is released. Detailed Information Item Description Copy Type The program product name for this operation Cnt Ac-J: Continuous Access Journal, Cnt Ac-J Z: Continuous Access Journal Z LDKC The LDKC number to which the journal belongs JNL The journal number MirrorID The mirror ID R-Cmd.Dev.(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the remote command device.
Item Description Copy Pace The initial copy speed set (the number of tracks you can copy at a time) Priority The priority of resynchronizing operation set (scheduling order) Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Pairs The number of resynchronized pairs Example 2: when the copy type is Cnt Ac-S Z 08xx,YYYY/MM/DD,HH:MM:SS.
=[{4C-0x00-0,4A-0x00-0,0x00,67676,6,32,0x000,LU,0x001,0x001, Mirror,Normal,Normal end}, {4C-0x00-1,4A-0x00-1,0x00,67676,6,32,0x000,LU,0x001,0x001, Mirror,Normal,Normal end}], Num.
Detailed Information 4 Item Description Copy Type The program product name for this operation Cnt Ac-J Z: Continuous Access Journal Z P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary data volume S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary data volume MirrorID The mirror ID S/N The serial number of the RCU CTRLID The controller ID of the RCU 7: XP7, 6: P9500, 5: XP24000/XP20000 Disk Array, 19: HUS VM Priority The priority of the copy operation Range T
Item Description Type The volume type of the volume on the primary site P-VOL: Primary volume, S-VOL: Secondary volume S-VOL Write Indicates whether the writing to the secondary volume is enabled Enable: Writing is enabled, Disable: Writing is disabled Kind The suspend type setting P-VOL Failure: Writing to the P-VOL is disabled S-VOL: Writing to the P-VOL is enabled Result The result of the operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code
Example 3: when the copy type is Cnt Ac-J 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Remote Replication],Split Pairs,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Copy Type=Cnt Ac-J +{P-VOL(Port-G-ID-LUN),S-VOL(Port-G-ID-LUN),MirrorID, S/N,CTRLID,Type,S-VOL Write,Range,Suspend Mode,Result} =[{4C-0x00-0,4A-0x00-0,0x00,67676,6,P-VOL,Disable,LU, Flush,Normal end}, {4C-0x00-1,4A-0x00-1,0x00,67676,6,P-VOL,Disable,LU, Flush,Normal end}], Num.
Detailed Information 4 Item Description Copy Type The program product name for this operation Cnt Ac-J Z: Continuous Access Journal Z P-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the primary data volume S-VOL(LDKC:CU:LDEV) The LDKC, CU, and LDEV numbers of the secondary data volume MirrorID The mirror ID S/N The serial number of the RCU CTRLID The controller ID of the RCU 7: XP7, 6: P9500, 5: XP24000/XP20000 Disk Array, 19: HUS VM Type Indicates whether the split data volume is a pri
={12345678911234567892123456789312345678941234567895123456789612 3456789712345678981234567899123456789012345678911234567892123456 78, -123456789112345678921234567893123456789412345678951234567896123 4567897123456789812345678991234567890123456789112345678921234567 89312345678941234567895123456789612345, -123456789112345678921234567893123456789412345678951234567896123 4567897123456789812345678991234567890123456789112345678921234567 89312345678941234567895123456789612345} Detailed Information Item Descriptio
Item Description Mode The type of rate when you specify an upper limit. IOPS: the I/O rate KB/s: the transfer rate When you specify Prio, this information is not output. Num. of PFC Groups The number of PFC groups whose settings are changed NOTE: • When the attribute of the host bus adapter in the PFC group changes from a prioritized WWN to a non-prioritized WWN, "Non-Prio" is output to Priority and "0" is output to Upper limit respectively.
Item Description Disable: Settings in the All Thresholds field are canceled. Threshold A configured value in the All Thresholds field. This information is output only when All Thresholds is configured. Mode The type of rate for All Thresholds IOPS: the I/O rate KB/s: the transfer rate This information is output only when All Thresholds is configured. [Perf Ctl] Set All Prio WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.
[Perf Ctl] Set Prio Port Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Perf Ctl],Set Prio Port,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,Priority,Use,Threshold/Upper Limit,Mode} =[{1A,Non-Prio,Enable,XXXXXXXX,IOPS}],Num.
Item Description Upper Limit When the WWN is a non-prioritized WWN, this information indicates the upper limit. When the WWN is a prioritized WWN, this information is not output. Mode The type of rate for the upper limit IOPS: the I/O rate KB/s: the transfer rate This information is not output when the WWN is a prioritized WWN. Num.
Detailed Information Item Description Mode An executed operation Add WWN: Added a WWN (an HBA is monitored). Delete WWN: Deleted a WWN (an HBA is not monitored). WWN An added or deleted WWN A WWN is a 16-digit number in the hexadecimal format. PFC Name A PFC name for an added or deleted HBA Priority An attribute specified to the HBA Prio: a prioritized WWN Non-Prio: a non-prioritized WWN This information is output only when a WWN (HBA) is added.
Item Description KB/s: the transfer rate This information is output only when you add a new PFC group. WWN WWNs of HBAs in the PFC group A WWN is a 16-digit number in the hexadecimal format. All WWNs are output for this item. You can add up to 32 WWNs to a PFC group. Num. of WWNs The number of WWNs of added or deleted HBAs Num. of PFC Group The number of PFC groups whose settings are changed [Perf Ctl] Update WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.
[Spreadsheet] CflSet Start Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [Spreadsheet],CflSet Start,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Input,Output}={C:\Set_IN.spd,C:\Set_OUT.spd} Detailed Information Parameter Description Input Indicates the name of the input file Output Indicates the name of the output file External Storage Descriptions [Ext Stor] Add External Volumes Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Serial The serial number the external storage system that the mapped external volume exists VolumeID1 The identification character 1 of the mapped external volume VolumeID2 The identification character 2 of the mapped external volume Device The device name that the mapped external volume notifies to the host Capa(blocks) The capacity of the mapped external volume indicated by blocks ExGroup The number of the external volume group and the reference number assigned to the externa
Item Description LDEV MP Blade ID MP Blade ID specified for the LDEV. When an MP Blade ID is specified automatically, "Auto" is output. LDEVResult The result of attempting to create an external path. If the LDEV is created normally, the audit log includes the following: LDEVResult: Normal endIf the LDEV is not created, the audit log includes this:LDEVResult: Error(xxxx-yyyyy): Abnormal end where xxxx is the Part code and yyyyy is the Error code Num.
Item Description Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Volumes The number of volumes in the external volumes that mapping has been released [Ext Stor] Disconnect ES Paths This logged information indicates that this Disconnect External Paths operation was only requested but not completed. Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description xxxx: Part code, yyyyy: Error code Num. of Groups The number of external volume groups that contain the disconnected external volume [Ext Stor] Edit ES Path Config Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit ES Path Config,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Group,Result} =[{E1-1,Enable,Normal end},{E1-2,Enable,Normal end}, {E1-3,Enable,Normal end},{E1-4,Enable,Normal end}], Num. of Groups=4 Example 2: Set the cache inflow control 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit ES VOLs, InflowControl,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of Groups The number of external volumes groups configured Example 4: Changing ALUA Permitted 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Edit ES VOLs,ALUA Permitted,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description LinkDown The Path Blockade watch value Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end where xxxx: Part code, yyyyy: Error code Num. of WWNs The number of WWNs setting of the external storage system [Ext Stor] Merge ES Path Grps Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Merge ES Path Grps,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
[Ext Stor] Reconnect ES Paths This logged information indicates that this Reconnect External Paths operation was only requested but not completed. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Reconnect ES Paths,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Port,WWN,Result}=[{1A,50560E8000C3E211,Normal end}, {1A,50560E8000C3E211,Normal end},{2A,50560E8000C3E212, Normal end}],Num.
[Ext Stor] Split ES Path Grp Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[Ext Stor],Split ES Path Grp,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PathGroup,NewPathGroup,ExGroup,Result} =[{1,11,E1-11,Normal end},{1,12,E1-21,Normal end}, {2,21,E2-11,Normal end}],Num.
Detailed Information Item Description SourceVolume The logical volume ID of the migration source. The number on the left of the colon is an LDKC number, the number between the colons is a CU number, and the number on the right of the colon is an LDEV number. TargetVolume The logical volume ID of the migration target. The number on the left of the colon is an LDKC number, the number between the colons is a CU number, and the number on the right of the colon is an LDEV number.
Item Description Online Data Migration: Online Data Migration Normal: Normal Result The result of operation Normal end: Normal end, Error(xxxx-yyyyy): Abnormal end, Not Execute: Not executed where xxxx: Part code, yyyyy: Error code Num. of VOLs The number of migration volumes. Cache Partition Descriptions [CPart] Edit CLPR Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1,, [CPart],Edit CLPR,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description OwnerID The owner ID 0: Indicates Remote Web Console 0xXX: Owner ID is expressed in two hexadecimal digits. [Shredder] End Shredding Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,SVP,,,,[Shredder], End Shredding,,Normal end,,Seq.=xxxxxxxxxx +{Times,Result} =[{1,Normal},{2,Normal},{3,Normal}],Num. of Data=3 Detailed Information Item Description Times The order of the shredding processes. A number from 1 to 8 is displayed.
Item Description 0: Indicates Remote Web Console 0xXX: Owner ID is expressed in two digits of the hexadecimal format Data The shredding data pattern Random: Random, 0xXXXX: Define Output File Whether the result of shredding is output to the file Disable: No output, Enable: Output Num. of Data The number of shredding data patterns Output LDEV Indicates LDEVs whose shredding results are output to the file Num.
Item Description Enable: enabled, Disable: disabled Num. of CLPRs The number of CLPRs HDD Easy Replace Descriptions [HDDEasyReplace] Replace Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=username,1,, [HDDEasyReplace],Replace,Easy-Replace,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +PDEV={HDD000-04},Num. of PDEVs=1 Detailed Information 218 Item Description PDEV The mounting location of the PDEVs (physical devices) to be replaced Num.
5 Audit log examples for encryption key operations This topic provides examples and descriptions of the audit logs produced by data encryption operations. The descriptions are listed alphabetically by function name and operation name. For detailed information on the version numbers in log output examples, see Table 4 (page 19) ENC Descriptions [ENC] Add keys to DKC Example 08xx,YYYY/MM/DD,HH:MM:SS.
=[{3E2332580B110E052D13C378866427A218EF1609881BC058FCBCF79FCD 7727C7,2013/07/06 09:20:37,BACK0706,Normal end,-}], Num.
[ENC] Clear Keys This information is output to the audit log information file 2, and it is asynchronous with the Remote Web Console operations. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,,,,,[ENC], Clear Keys,,Normal end,,,Seq.
[ENC] Create Keys This information is output to the audit log information file 2, and it is asynchronous with the Remote Web Console operations. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,,,,,[ENC], Create Keys,,Normal end,,,Seq.
Detailed Information for Example 2 Item Description Key Type The purpose of the use of the created key KEK: key encription keys (used as a key wrapping key) UUID The UUID of the created encryption key on the key management server A hyphen (-) is displayed when an error occurred while processing.
[ENC] Delete Keys Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Delete Keys,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Key ID}=[1,2],Num. of Keys=2 Detailed Information Item Description Key ID A deleted encryption key number Num. of Keys The number of deleted encryption keys [ENC] Delete Keys This information is output to the audit log information file 2, and it is asynchronous with the Remote Web Console operations.
Item Description A hyphen (-) is displayed unless an error occurred while processing. For details on return values, see the manuals for each key management server. Num. of Keys The number of encryption keys to be deleted [ENC] Edit Encryption Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Edit Encryption,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{PG,Encryption}=[{XX-XX,Enable},{XX-XX,Disable}],Num.
[ENC] Edit Password Policy Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC], Edit Password Policy,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +{Numeric Characters (0-9),Uppercase Characters (A-Z), Lowercase Characters (a-z),Symbols,Total}={1,2,3,4,10}, Num.
[ENC] Rekey KEK Dynamic Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Rekey KEK Dynamic,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [ENC] Restore Keys This logged information is output when encryption key information in the storage system is restored with key information obtained externally. Example 08xx,YYYY/MM/DD,HH:MM:SS.
[ENC] Retry KEK Dynamic Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC],Retry KEK Dynamic,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx [ENC] Set Up Key Mng Serv Example 1: Using a key management server 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,RMI AP,uid=user-name,1, Task Name,[ENC], Set Up Key Mng Serv,,Normal end, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Root Certificate File Name The file name of the root certificate Num. of Servers The number of the configured key management servers [ENC] Use Keys for CEK/KEK This information is output to the audit log information file 2, and it is asynchronous with the Remote Web Console operations. Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,,,,,[ENC], Use Keys for CEK/KEK,,Normal end,,,Seq.
6 Audit log examples of commands sent from hosts, computers using RAID Manager, or hosts using Business Continuity Manager This topic provides examples and descriptions of the audit logs when a storage system receives commands sent from hosts, computers using RAID Manager, or hosts using Business Continuity Manager.
Detailed Information Item Description Command The command name Device Group The name of a device group to be registered When an LDEV is added, the name of the device group to which the LDEV is added is output LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of an LDEV to be added to the device group Num.
Detailed Information Item Description Command The command name Pool ID The pool number of a pool for Thin Provisioning to be created Pool Name The pool name of a pool for Thin Provisioning to be created No output if the pool name is not set LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of a pool volume Num.
Detailed Information Item Description Command The command name Port The name of a port to which a host group is added When a virtual storage machine is specified, the port name of the virtual storage machine is output.
Detailed Information Item Description Command The command name PG The parity group number of an LDEV to be created If the LDEV to be created is an external volume, "E" is added on the top of the parity group number. LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of the LDEV to be created Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Add Ldev(Thin Provisioning) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Add LUN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band OPEN,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Add RCU Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description RCU Port The port name of the remote storage system to be added Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Add Resource(Group) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Port The name of a port to be registered or deleted This item is output when the resource of the operation target is Port or Host Group Host Group ID The number of a host group to be registered or deleted This item is output when the resource of the operation target is Host Group Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Add Snap Pool Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description Command The command name Snapshot Group The name of a snapshot group Pool ID The pool ID of a pool to which a pair to be registered belongs P-VOL(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of the primary volume of a pair to be registered When a virtual storage machine is specified, the volume number of the virtual storage machine is output.
Detailed Information Item Description Command The command name WWN The WWN on which a nick name is set Nick Name The nickname to be set Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Add SSID Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Command The command name Port The name of a port to which a WWN is set When a virtual storage machine is specified, the port name of the virtual storage machine is output.
Item Description Path Group ID The path group ID of the external volume Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format CTQM Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Delete Device Group Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Command=Delete Device Group ++Device Group=AAAAAAAA ++LDEV(LDKC:CU:LDEV)={0x00:0xAA:0xBB,0x00:0xCC:0xDD,……, 0x00:0xEE:0xFF},Num.
+0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Item Description Command The command name Port The name of a port from which a host group is deleted When a virtual storage machine is specified, the port name of the virtual storage machine is output.
Detailed Information Item Description Command The command name JNLG The journal group number LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of a journal volume to be deleted Num. of LDEVs The number of journal volumes to be deleted Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Delete Ldev Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description LUN The LU number to be deleted No output when it is specified by the command option LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of an LDEV to be deleted No output when it is specified by the command option Virtual Storage Machine S/N The serial number of the virtual storage machine No output when a virtual storage machine is not specified Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary for
Delete Pool(Ldev) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Command=Delete Pool(Ldev) ++Pool ID=AA ++LDEV(LDLC:CU:LDEV)={0x00:0xAA:0xBB,0x00:0xCC:0xDD,……, 0x00:0xEE:0xFF},Num.
Delete RCU Path Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
++P-VOL(LDKC:CU:LDEV)=0x00:0xAA:0xBB,MU=A, Virtual Storage Machine S/N=23456 +0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Item Description Command The command name P-VOL(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of the primary volume of a pair to be deleted When a virtual storage machine is specified, the volume number of the virtual storage machine is output.
Detailed Information Item Description Command The command name Port The name of a port to which a WWN, on which the definition of priority is deleted, belongs WWN The WWN on which the definition of priority is deleted Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Delete PFC WWN(Nick Name) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description "Free" is output when CU Free is selected SSID The SSID to be deleted Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Delete WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Disconnect Path Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
+Command=Initialize Ldev(Format) ++LDEV(LDKC:CU:LDEV)=0x00:0xAA:0xBB +0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Item Description Command The command name LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of an LDEV to be formatted Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Initialize Ldev(Shredding) Example 08xx,YYYY/MM/DD,HH:MM:S
Detailed Information Item Description Command The command name LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of an LDEV in which deletion of its data is to be stopped Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Map Resource(LDEV) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Modify CLPR Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Command The command name PG The parity group number of the external volume ALUA Switch Indicates whether the ALUA mode is enabled or disabled Disable or Enable will appear Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify External Group(Cache Inflow) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description Through: Cache through mode Write Sync: Write synchronous mode Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify External Group(Load Balance Mode) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Modify Host Group(Host Mode) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
+Command=Modify Journal ++JNLG=0x001 +0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Item Description Command The command name JNLG The number of a journal group to be changed Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify Journal(MP Blade) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Modify Ldev(CLPR) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Modify Ldev(Discard Zero Page) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Command The command name LDEV(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of an LDEV on which a name is designated Nick Name The name to be designated on the LDEV Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify Ldev(Restore) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Modify Ldev(Tier) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Item Description Command The command name Pool ID The pool number of a pool to be restored Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify Pool(Threshold) Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Item Description Connection The topology of the Fabric switch FC-AL: FC-AL (Fibre Channel-Arbitrated Loop) is selected P-to-P: Point-to-Point is selected Switch Indicates whether the LUN security setting is enabled or disabled Enable or Disable will appear Virtual Storage Machine S/N The serial number of the virtual storage machine No output when a virtual storage machine is not specified Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in bina
Detailed Information Item Description Command The command name S/N The serial number of the remote storage system MCU The CU number of the local storage system "Free" is output when CU Free is selected RCU The CU number of the remote storage system "Free" is output when CU Free is selected Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify Snapshot(Restore) Example 08xx,YYYY/MM/DD,HH:MM:SS.
Detailed Information Item Description Command The command name P-VOL(LDKC:CU:LDEV) The LDKC number, the CU number, and the LDEV number of the primary volume shared by a pair to be resynchronized When a virtual storage machine is specified, the volume number of the virtual storage machine is output.
Detailed Information Item Description Command The command name Port The name of a port to which a host group, in which the definition of priority is set, belongs Group Name The name of the host group to which the definition of priority is set Priority Indicates the setting of the definition of priority Enable: The priority is given, Disable: The priority is not given Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Modify PF
Item Description WWN Nick Name The nickname of the WWN on which the definition of priority is set Priority Indicates the setting of the definition of priority Enable: The priority is given, Disable: The priority is not given Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Monitor Pool Example 08xx,YYYY/MM/DD,HH:MM:SS.
Item Description The port number and the LU number show the expanded LU of RAID Manager MCU S/N* The serial number of the local storage system MCU SSID* The SSID to which a volume for the local storage system belongs No output if it is not specified at the command option RCU S/N* The serial number of the remote storage system RCU SSID* The SSID to which a volume for the remote storage system belongs No output if it is not specified at the command option Virtual Storage Machine S/N The serial numb
Item Description RCU S/N* The serial number of the remote storage system RCU SSID* The SSID to which a volume for the remote storage system belongs No output if it is not specified at the command option Resync Type Indicates the direction of resynchronizing a pair Normal: Normal direction (Primary volume to secondary volume) Reverse: Reverse direction (Secondary volume to primary volume.) This item is output only when the Copy Kind is Local.
Item Description RCU SSID* The SSID to which a volume for the remote storage system belongs No output if it is not specified at the command option Range The range of pair split Group: Split by consistency group unit LU: Split by LU unit Virtual Storage Machine S/N The serial number of the virtual storage machine No output when a virtual storage machine is not specified Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format *When a v
Item Description Virtual Storage Machine S/N The serial number of the virtual storage machine No output when a virtual storage machine is not specified Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format *When a virtual storage machine is specified, the value of the virtual storage machine is output. Reallocate Pool(Start) Example 08xx,YYYY/MM/DD,HH:MM:SS.
++Pool ID=AA,Pool Name=XXXXXXX +0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Item Description Command The command name Pool ID The pool number of a pool to be renamed Pool Name The pool name after the change Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Reset Command Status Example 08xx,YYYY/MM/DD,HH:MM:SS.
Reset WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Set WWN Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,Out-of-band,uid=user-name, 196,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
+0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Parameter Description Command The command name Copy Type The copy type of the consistency group which is a target of registration or changing options BC Z: Business Copy Z, Cnt Ac-S Z: Continuous Access Synchronous Z CTG The consistency group which is a target of registration or changing options Command parameter Indicates the 16 byte parameter added in the storage system and the com
Parameter Description This item is output only when the copy type is Cnt Ac-J Z. Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Add RCU Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name, ,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Detailed Information Parameter Description Command The command name Copy Type The copy type BC Z: Business Copy Z, Cnt Ac-J Z: Continuous Access Journal Z Kind The operation kind Set: Setting of a suspend reservation Reject: Releasing of a suspend reservation CTG The consistency group which is a target of a suspend reservation Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Build Command Device Example 08xx,YYYY/MM/DD,HH:MM
Detailed Information Parameter Description Command The command name VOL(CU:LDEV) The CU number and the LDEV number of the volume, allocation for which as a command device is to be released APID The application ID Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Delete CTG Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name, ,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Parameter Description Cnt Ac-J Z: Continuous Access Journal Z P-VOL(CU:LDEV) The CU number and the LDEV number of the primary volume S-VOL(CU:LDEV) The CU number and the LDEV number of the secondary volume MCU S/N The serial number of the local storage system MCU SSID The SSID to which a volume for the local storage system belongs RCU S/N The serial number of the remote storage system RCU SSID The SSID to which a volume for the remote storage system belongs Command parameter Indicates the 16
=[{12345,5,0x0FF,0xFE:0xFF},{12345,5,0x0FF,0xAB:0xFF}, {12345,5,0x0FF,0x03:0xFF}],Num.
+Command=Remote DKC Control ++S/N=XXXXX,SSID=0xBBBB,VOL(CU:LDEV)=0xAA:0xBB,APID=0,I/F=1 +0000010200000000 0000000000000000 +0123456789ABCDEF 0123456789ABCDEF 0123456789ABCDEF,(snip) Detailed Information Parameter Description Command The command name S/N The serial number of the storage system for executing the command No output if it is not specified at the command option SSID The SSID to which a volume for the storage system for executing the command belongs No output if it is not specified at the
Parameter Description RCU SSID The SSID to which a volume for the remote storage system belongs Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Run Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name, ,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Parameter Description RCU S/N The serial number of the remote storage system RCU SSID The SSID to which a volume for the remote storage system belongs Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format Suspend Pairs Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name, ,,[Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
EST PAIR Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name,,, [Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
Parameter Description Num. of Paths The number of paths to be created Command parameter Indicates the 16 byte parameter added in the storage system and the command parameter in binary format SPLIT PAIRS Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name,,, [Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.=xxxxxxxxxx +Command=SPLIT PAIRS ++S-VOL(CU:LDEV)={0x00:0x01,0x01:0x02},Num.
TERM PAIR Example 08xx,YYYY/MM/DD,HH:MM:SS.xxx, 00:00,In-band MF,uid=user-name,,, [Config Command],,,Accept, from=xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx,,Seq.
7 Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
HP websites For additional information, see the following HP websites: • http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/service_locator • http://www.hp.com/support/manuals • http://www.hp.com/support/downloads • http://www.hp.
Table 19 Document conventions (continued) Convention Element Monospace text • File and directory names • System output • Code • Commands, their arguments, and argument values Monospace, italic text • Code variables • Command variables Monospace, bold text WARNING! CAUTION: IMPORTANT: NOTE: TIP: Emphasized monospace text Indicates that failure to follow directions could result in bodily harm or death. Indicates that failure to follow directions could result in damage to equipment or data.
A Audit log user operations This topic describes which user operations trigger logging. The same log is output when a user perform an operation using each Remote Web Console menu, clicking a button on the main window, or using General Tasks.
Table 23 Logical Device GUI operation Audit Log Output Submenu Description Function Name Operation Name Create LDEVs Creating an LDEV PROV Create LDEVs Format LDEVs Format LDEVs(H) Format LDEVs(Q) Set SSID LDEV Name Edit V-VOL Option Delete LDEVs Deleting an LDEV PROV Delete LDEVs Edit LDEVs Editing LDEV information PROV LDEV Name Edit LDEVs(tier) Edit V-VOL Option Format LDEVs Formatting an LDEV PROV Format LDEVs Formatting an LDEV using the PROV Write to Control Blocks function Form
Table 23 Logical Device (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Edit Cmd Dev(Sec) Edit Cmd Dev(Auth) Edit Cmd Dev(DevGrp) Release Mainframe Command Devices Releasing Continuous Access Remote Synchronous Z command Replication devices Delete Cmd.Dev *Abort Shredding is output when a shredding operation is aborted from the Confirm window during a shredding operation by Shred LDEVs.
Table 24 Port/Host Group (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name Authentication Setting port information PROV Set FCSP Port Info2, 3 PROV Set FCSP Target2, 3 Creating, changing, or deleting the host authentication information PROV Set FCSP Host2, 3 Registering authentication Information PROV Set FCSP Port Switch2, 3 Setting default such as user name and secret Registering or deleting authentication information Authentication (Host Group):
Table 25 Pool (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name Monitor Pools Starting the performance monitoring of a pool PROV Monitor Pools Stop Monitoring Pools Stopping the performance monitoring of a pool PROV Stop Monitoring Start Tier Relocation Starting the tier relocation of a pool PROV Relocate Pool Stop Tier Relocation Stopping the tier relocation of PROV a pool Stop Relocating Restore Pools Restoring a pool PROV Restore Pools In
Table 27 External Storage (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Disconnecting an external storage system Ext Stor Disconnect ES VOLs Reconnect External Storage Reconnecting an external Systems storage system Ext Stor Reconnect ES VOLs Deleting a path from an external path group Changing priority among external paths Disconnect External Storage Systems Table 28 Local Replication GUI operation Audit Log Output Submenu Description Function Na
Table 29 Remote Replication GUI operation Audit Log Output Submenu Description Create Pairs Creating pairs for Continuous Remote Access Synchronous, Replication Continuous Access Synchronous Z, Continuous Access Journal, or Continuous Access Journal Z Create Pairs1 Split Pairs Splitting pairs for Continuous Remote Access Synchronous, Replication Continuous Access Synchronous Z, Continuous Access Journal, or Continuous Access Journal Z Split Pairs1 Resync Pairs Resynchronizing pairs for Remote Con
Table 29 Remote Replication (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name and Continuous Access Journal Z Assign Remote Command Devices Assigning remote command Remote devices for Continuous Access Replication Journal and Continuous Access Journal Z R-Cmd.Dev. Release Remote Command Releasing remote command Remote Devices devices for Continuous Access Replication Journal and Continuous Access Journal Z R-Cmd.Dev.
Table 30 Journal (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Access Journal and Continuous Access Journal Z Assign Journal Volumes Assigning journal volumes for Remote Continuous Access Journal Replication and Continuous Access Journal Z Journal Vol When you apply two or more settings of the same type to the storage system at the same time, the log information is output as one entry.
Table 33 Other function GUI operation Audit Log Output Submenu Description Function Name Data Retention Attribute / S-VOL / Reserved/ PROV Operation Name Edit DRU Attribute1 Mode Clear / Retention term Cache Residency Expiration-Lock PROV DRU Expiration Lock1 Set Cache Residency (Open Volume) Perf Mon Set Open DCR1, 2 Set Cache Residency (M/F Volume) Perf Mon Set M/F DCR1, 2 Release Cache Residency (Open Volume) Perf Mon Delete Open DCR1, 2 Release Cache Residency (M/F Volume) Perf Mo
Table 36 Performance Monitor GUI operation Audit Log Output Submenu Description Function Name Operation Name Edit Monitoring Switch Starting/stopping monitoring Perf Mon Edit Monitoring SW Edit CU Monitor Mode Setting target CUs for monitoring Perf Mon Edit CU Monitor Mode Edit WWN Monitor Mode Setting target WWNs for monitoring Perf Mon Edit WWN MonitorMode Add New Monitored WWNs Adding new WWNs for monitoring Perf Mon Edit WWN MonitorMode Edit WWN Editing WWN Perf Mon Edit WWN Dele
Table 36 Performance Monitor (continued) GUI operation Submenu Audit Log Output Description Function Name Operation Name Setting priority for PFC groups Perf Ctl (Attribute / Upper) Change PFCGrp1, 2 Changing PFC group name PFCGrp Del/Chg1, 2 Perf Ctl Set All Prio WWN Set All Prio WWN Clearing port settings due to removing port controllers Perf Ctl Clear PFC Info2 Notes: 1.
Table 38 Resource Management GUI operation Audit Log Output Submenu Description Function Name Operation Name Create Resource Groups Creating a resource group PROV Create Resource Grps Adding a resource Move Resources Edit Resource Group Changing a resource group name PROV Edit Resource Grp Delete Resource Groups Deleting a resource group PROV Delete Resource Grps Add Resources Adding a resource to a resource group PROV Move Resources Remove Resources Removing a resource from a resou
Table 39 Security (continued) GUI operation Audit Log Output Submenu Encryption Keys Description Function Name Operation Name Restore Keys from File Restoring encryption keys with backup files on the Remote Web Console PC ENC Restore Keys Restore Keys from Server Restoring encryption keys ENC with backup keys on the key management server Restore Keys View Backup Keys on Server Deleting encryption keys backed up on the key management server ENC Delete Keys on Server9 Edit Encryption Environ
Table 40 Environmental Setting (continued) GUI operation Audit Log Output Submenu Description Function Name Operation Name PP Apply Remove Licenses Uninstalling licenses PP Removal chk1 PP KEY PP Apply Enable Licenses Enabling licenses PP Enable chk1 PP KEY PP Apply Disable Licenses Disabling licenses PP Disable chk1 PP KEY PP Apply Update License Statuses Updating license statuses Update License1 PP KEY PP Apply Edit Alert Settings Edit System Options Setting a destination of the al
When executing single sign-on from Command View Advanced Edition Suite Table 43 When executing single sign-on from Command View Advanced Edition Suite GUI operations Issuing OneTimeKey from Command View Advanced Edition Suite Launching Remote Web Console from Command View Advanced Edition Suite 308 Audit log user operations Audit Log Output Function Name Operation Name BASE HCSSO SetOneTimeKey HCSSO Authentication
B Audit log SVP operations This topic describes SVP operations as well as function names and operation names that is output to audit logs.
Table 45 Using Maintenance button on SVP (continued) SVP Operations Audit Log Output Function Operation Function Name Operation Name Maintenance SFP Maintenance Maintenance Type Change Maintenance Switch SVP Maintenance Switch SVP Maintenance Transfer Config Maintenance Transfer Config Using Install button Table 46 Using Install button on SVP SVP Operations Function 310 Audit Log Output Function Name Operation Name Define Configuration and Define Configuration and Install Install Inst
Table 46 Using Install button on SVP (continued) SVP Operations Audit Log Output Function Operation Function Name Operation Name Change Configuration LUN Configuration Install Force Reset Change Configuration DCR Configuration Install DCR Prestaging Change Configuration DCR Configuration Install M/F DCR Change Configuration DCR Configuration Install Open DCR Change Configuration CVS Configuration Install Install CV Change Configuration CVS Configuration Install Volume to Space
Using Monitor button Table 48 Using Monitor button on SVP SVP Operations 312 Audit Log Output Function Operation Function Name Operation Name Threshold Threshold Monitor Threshold Audit log SVP operations
C Audit log GUI reference This topic describes the audit log screens in the Remote Web Console GUI. The GUI illustrations in this guide were created using a Windows computer with the Internet Explorer browser. Actual windows may differ depending on the operating system and browser used. GUI contents also vary with licensed program products, disk array models, and firmware versions. Audit Log Properties window Use this window to download audit log files to the Remote Web Console computer.
Related topics • “Downloading audit log files” (page 26) Edit Audit Log Settings wizard Use the Edit Audit Log Settings wizard to transfer the audit log or download a syslog file to the Remote Web Console computer.
Syslog tab Item Description Transfer Protocol Selects a protocol to transfer the audit log. • New Syslog Protocol (TLS1.2/RFC5424) • Old Syslog Protocol (UDP/RFC3164) Primary Server Selects whether to use the syslog server. • Enable: Transfers the audit log to the syslog server. • Disable: Do not transfer the audit log to the syslog server. Primary Server- Server settings Enters an IP address of a server you want to set as a syslog server.
Item Description Specifies this item only when New Syslog Protocol (TLS1.2/RFCS5424) is selected at Transfer Protocol. Primary Server- Password Enters a password for the client certificate. Up to 128 characters can be entered for the password. Allowed characters are alphanumeric characters and symbols: ! # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | } ~. Inputs this item only when Client Certificate File Name is specified.
Item Description Download Syslog Downloads the syslog file to the Remote Web Console computer. Send Test Message to Syslog Sends the test log to the syslog server. Server FTP tab Item Description Primary Server Selects whether to use the FTP server. • Enable: Transfers the audit log file to the FTP server. • Disable: Do not transfer the audit log file to the FTP server. Primary Server- IP Address Sets an IP address for the primary FTP server.
Item Description Secondary Server Selects whether to use an alternative server (secondary server) to the FTP server. • Enable: Transfers the audit log file to the secondary FTP server. • Disable: Do not transfer the audit log file to the secondary FTP server. Secondary Server- IP Address Enters an IP address of a server you want to set as a secondary FTP server. The restriction for the available values is the same as that of Primary Server- IP Address.
Syslog Server table This table displays only when you have made settings in the Syslog tab of the Edit Audit Log Settings window. Item Description Primary Server- Syslog Server Indicates whether to use the syslog server or not. Primary Server- IP Address Indicates the IP address of the syslog server. Primary Server- Port Number Indicates the port number to be used on the syslog server. Primary Server- Client Certificate File Name Indicates the file name of the client certificate.
Item Description Secondary Server- FTP Server Indicates whether to use an alternative server to the FTP server. Secondary Server- IP Address Indicates the IP address of the alternative server to the FTP server. Secondary Server- Login User Name Indicates the login user name of the alternative server to the FTP server. Secondary Server- Password Indicates the password of the alternative server to the FTP server with "*" mark.
Glossary allocation The ratio of allocated storage capacity versus total capacity as a percentage. Allocated storage refers to those logical devices (LDEVs) that have paths assigned to them. Allocated storage capacity is the sum of the storage of these LDEVs. Total capacity is the sum of the capacity of all LDEVs on the disk array. BC P9000 or XP Business Copy. An HP application that provides volume-level, point-in-time copies in the disk array.
to be associated with 1 to 36 LDEVs. Essentially, LUSE makes it possible for applications to access a single large pool of storage. M-VOL Main volume. MCU Main control unit. OPEN-x A general term describing any of the supported OPEN emulation modes (for example, OPEN-E). There are two types of OPEN-x devices: legacy OPEN-x devices with a fixed size (such as OPEN-3, OPEN-8, OPEN-9, and OPEN-E), and OPEN-V, which has a variable size and is a CVS-based volume.
Index C contacting HP, 290 conventions document, 291 storage capacity values, 291 text symbols, 292 D document conventions, 291 related information, 290 documentation HP website, 290 providing feedback, 290 H help obtaining, 290 HP subscription service, 290 technical support, 290 R related documentation, 290 S storage capacity values conventions, 291 subscription service, HP, 290 symbols in text, 292 T technical support HP, 290 service locator website, 291 text symbols, 292 typographic conventions, 291
