DUA1607-5AAA02.fm Page 1 Tuesday, September 26, 2000 3:14 PM SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE For installation by suitably qualified service personnel only. CAUTION: All installed Type 3 Power Modules must have a DC cable or a protective cover fitted on completion of installation. The Type 3 Power Module is a UL listed accessory for use only with the UL listed Advanced RPS Chassis.
DUA1607-5AAA02.fm Page 2 Tuesday, September 26, 2000 3:14 PM 2 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE Introduction The Type 3 Power Module fits into the SuperStack 3 Advanced RPS Chassis (3C16071, 3C16071A, or 3C16071B). The module provides redundant power from the Advanced RPS chassis to the SuperStack 3 Switch 4900 Series.
DUA1607-5AAA02.fm Page 3 Tuesday, September 26, 2000 3:14 PM SuperStack 3 Advanced RPS Chassis Loading Limitations 3 SuperStack 3 Advanced RPS Chassis Loading Limitations WARNING: Do not overload the chassis — refer to Table 1 “Maximum Number of Advanced RPS Power Modules per Chassis” to determine loading limitations. It is important that the loading limitations are not exceeded.
DUA1607-5AAA02.fm Page 4 Tuesday, September 26, 2000 3:14 PM 4 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE Figure 1 shows the rear view of an Advanced RPS chassis and the power module slot numbers to help you determine which slots to use for your Type 3 Modules to meet the permitted configurations detailed in Table 1.
DUA1607-5AAA02.
DUA1607-5AAA02.fm Page 6 Tuesday, September 26, 2000 3:14 PM 6 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE Safety Information You must read the following safety information before carrying out any installation or removal of components, or any maintenance procedures on the SuperStack 3 Advanced RPS. WARNING: Warnings contain directions that you must follow for your personal safety. Follow all directions carefully.
DUA1607-5AAA02.fm Page 7 Tuesday, September 26, 2000 3:14 PM Safety Information ■ ■ 7 When you connect DC cables to a Type 3 Power Module you must tighten the screws on all DC cable connectors with a suitable tool. When connecting a DC cable to the power module, you must take off the D-type connector protective cover by removing the fixings with a suitable tool. Keep the cover and the fixings in a safe place. If you disconnect the DC cable at any time, you must then replace the protective cover.
DUA1607-5AAA02.fm Page 8 Tuesday, September 26, 2000 3:14 PM 8 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE CAUTION: Un défaut fugitif d’alimentation peut exister au niveau du connector su Power Module de Type 3 lorsque ce module est dans le chassis RPS avancé. Wichtige Sicherheitsinformationen Der Ein- und Ausbau der Anlage ist nur von ausgebildetem Wartungspersonal auszuführen.
DUA1607-5AAA02.fm Page 9 Tuesday, September 26, 2000 3:14 PM Installing the Power Module 9 CAUTION: Wenn sich das Type 3 Power Module im Advanced RPS Chassis befindet kann es zu einer Energiegefahr am DC Stecker kommen. Installing the Power Module CAUTION: Never plug a hot power module into the Advanced RPS. You may damage the power module. Allow sufficient time (approximately 1 minute) for the module to cool down before inserting it into the power module slot.
DUA1607-5AAA02.fm Page 10 Tuesday, September 26, 2000 3:14 PM 10 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE Connecting the DC Cables Standard Type 3 Module DC Cable To connect a standard Type 3 Module DC cable (supplied with this module) to provide redundancy to your SuperStack 3 unit: 1 Ensure the Type 3 Power Module is in the Advanced RPS chassis before connecting or disconnecting a standard DC cable or the protective cover.
DUA1607-5AAA02.fm Page 11 Tuesday, September 26, 2000 3:14 PM Technical Information 11 CAUTION: Do not attempt to use a ‘Y’ cable to power two separate SuperStack 3 units. The equipment may not operate. CAUTION: All DC cable screws must be tightened with a suitable tool. Technical Information Mechanical Weight 633 g (22 oz) Size 276 x 87 x 42 mm (10.8 x 3.4 x 1.6 in.) Electrical - Maximum Current Available +27.0 volts 12.
DUA1607-5AAA02.fm Page 12 Tuesday, September 26, 2000 3:14 PM 12 SUPERSTACK® 3 ADVANCED RPS TYPE 3 POWER MODULE (3C16075) INSTALLATION GUIDE Problem Power module present, No Output LED ON Power module present, Yellow LED ON Possible Fault ■ Power module is incorrectly installed. ■ DC cable is not connected. ■ SuperStack 3 unit is not connected. ■ SuperStack 3 unit does not require RPS power. ■ LED failed. Contact your supplier.
