Quick Configuration Guide A7000 1xSerial Module (J8458A) 2005-04

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

61195866L1-42B www.procurve.com 1

ProCurve Secure Router

(with 1xSerial Module)

Quick Configuration Guide 5991-2116 April 2005

• V.35 or X.21 cable for connecting the system to the existing network.

• VT100 terminal or PC with VT100 emulation software.

• Serial cable (5184-1894) supplied with the router. This console cable is used in other ProCurve

switches such as the 5300xl series. The console port is a DB-9 DTE male connector.

Frame Relay Diagram

PPP Diagram

Equipment Required

Note

This quick configuration guide provides step-by-step instructions for configuring

your application. The configuration script is available at the end of this document.

The configuration parameters used in the example outlined in this document are for

instructional purposes only. Please replace all underlined entries (example

) with your

specific parameters to configure your application.

Network Diagrams

Branch Office Corporate HQ

ProCurve Secure

Router 7102dl/7203dl

ProCurve Secure

Router 7102dl/7203dl

LAN IP: 10.10.10.1 /24

WAN IP: 192.168.72.2 /30

eth 0/1

LAN IP:10.10.20.7 /24

DLCI 16

Annex D Signaling

192.168.72.1 /30

FR 1.x

SHIFT

QUICK

TSU IQ

ENTER

CANCEL

NEXT PREV

ADD

DELETE

CSU/DSU

SHIFT

QUICK

TSU IQ

ENTER

CANCEL

NEXT PREV

ADD

DELETE

CSU/DSU

V.35 or X.21

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Network IP: 10.10.20.0

Network IP: 10.10.10.0

serial 1/1

Point-to-Point T1

PPP Signaling

192.168.72.1 /30

PPP 1

Branch Office Corporate HQ

ProCurve Secure

Router 7102dl/7203dl

ProCurve Secure

Router 7102dl/7203dl

LAN IP: 10.10.10.1 /24

WAN IP: 192.168.72.2 /30

eth 0/1

LAN IP:10.10.20.7 /24

SHIFT

QUICK

TSU IQ

ENTER

CANCEL

NEXT PREV

ADD

DELETE

CSU/DSU

SHIFT

QUICK

TSU IQ

ENTER

CANCEL

NEXT PREV

ADD

DELETE

CSU/DSU

V.35 or X.21

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Network IP: 10.10.20.0

Network IP: 10.10.10.0

Summary of content (11 pages)

PAGE 1
ProCurve Secure Router (with 1xSerial Module) Quick Configuration Guide 5991-2116 April 2005 Equipment Required • V.35 or X.21 cable for connecting the system to the existing network. • VT100 terminal or PC with VT100 emulation software. • Serial cable (5184-1894) supplied with the router. This console cable is used in other ProCurve switches such as the 5300xl series. The console port is a DB-9 DTE male connector.
PAGE 2
Configure the Unit The ProCurve Secure Router may be initially accessed and managed via a console session. Refer to Initiate a Console Session for console session instructions. Initiating a Telnet session requires using a hub and two Ethernet cables (one for the PC and one for the unit). Refer to Configure Telnet Access on page 6 to configure Telnet session settings. Initiate a Console Session 1.
PAGE 3
Configure the Serial Interface The following steps demonstrate configuring a serial network interface. 1. At the (config)# prompt, enter interface serial 1/1 to activate the interface configuration mode for the serial network interface. 2. Enter serial-mode v35 to configure the serial interface for use with the V.35 adapter cable (J8757A). 3. Enter no shutdown to activate the interface to pass data. Note Skip to Configure the Virtual PPP Interface on page 4 for PPP configuration.
PAGE 4
Configure the Virtual PPP Interface The following steps show how to configure a PPP virtual interface (labeled 1) to the corporate router. Skip to Bind the Interfaces if you are using Frame Relay. 1. At the (config)# prompt, enter interface ppp 1 to create a PPP virtual interface labeled 1. 2. Enter ip address 192.168.72.1 255.255.255.252 to assign an IP address to the PPP endpoint using a 30-bit mask. 3. Enter no shutdown to activate the virtual interface to pass data. 4.
PAGE 5
Configure Dynamic Routes Scenario 1: Dynamic Routing via OSPF 1. At the (config)# prompt, enter router ospf to activate the OSPF configuration mode. Your prompt should now display (config-ospf)#. 2. Specify the networks: Corporate HQ Router (config-ospf)#network 10.10.10.0 0.0.0.255 area 0 (config-ospf)#network 192.168.72.0 0.0.0.3 area 0 Branch Office Router (config-ospf)#network 10.10.20.0 0.0.0.255 area 0 (config-ospf)#network 192.168.72.0 0.0.0.3 area 0 3.
PAGE 6
Configure Telnet Access The following steps show how to access the Telnet configuration parameters and change the password. For this example, replace the underlined word with a password of your choosing. The ProCurve Secure Router supports five Telnet sessions (0 through 4). 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet session. Your prompt should now display (config-telnet-0-4)#. 3.
PAGE 7
Script for this Example Note The script below contains ALL configuration parameters for each part of this example and cannot be used in its entirety. Each section is divided by a row of symbols (*). Use only the sections that pertain to your application. (For example, if your application is Frame Relay, do not use the PPP sections.) ! This is a sample script to configure the 1xSerial Module. ! ! Enter the enable mode. enable ! ! Enter the global configuration mode.
PAGE 8
! ! Set the signaling mode. frame-relay lmi-type ansi ! ! Activate the interface to pass data. no shutdown ! ! Exit back to the global configuration mode. exit ! ! PVC CONFIGURATION !*************************************************************! ! Create a Frame Relay PVC (with DLCI 16) under Frame Relay ! virtual interface 1. interface fr 1.16 ! ! Your prompt should now display Router(config-fr1.16)#. ! ! Now assign DLCI 16 to the pvc.
PAGE 9
! BINDING THE INTERFACES - PPP !*************************************************************! ! Connect the serial interface module to the virtual PPP ! interface (ppp 1). ! bind 1 serial 1/1 ppp 1 ! ! CONFIGURING STATIC ROUTES - CORP HQ ROUTER - DEFAULT ROUTE !************************************************************************************************! ! Configures the default gateway to the internet router. ! ! Enter the default gateway ip address to the route table.
PAGE 10
! Specify the Branch Office networks. network 10.10.20.0 0.0.0.255 area 0 network 192.168.72.0 0.0.0.3 area 0 ! ! Exit back to the global configuration mode. exit ! ! CONFIGURING DYNAMIC ROUTES VIA RIP !*************************************************************! ! Enter the RIP configuration mode. router rip ! ! Your prompt should now display (config-rip)#. ! ! Define RIP version 2. version 2 ! ! Specify the Corp HQ networks. network 10.10.10.0 255.255.255.0 network 192.168.72.0 255.255.255.
PAGE 11
! ! SAVE THE CONFIGURATION !*************************************************************! ! Exit the global configuration mode. exit ! ! Your prompt should now display Router>. ! ! Save the current configuration to memory. copy running-config startup-config ! ! Exit to close the configuration session. exit ! ! End script Copyright 2005 Hewlett-Packard Development Company, LP. The information contained herein is subject to change without notice.