Quick Configuration Guide for A7000 dl 1xE1 or 1xE1 + G.703 Modules 2005-04

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

61195878L1-42B www.procurve.com 1

ProCurve Secure Router

(with 1xE1 or 1xE1 + G.703 Modules)

Quick Configuration Guide 5991-2117 April 2005

• Category 5 - UTP cable for connecting the system to the existing network.

• VT100 terminal or PC with VT100 emulation software.

•

Serial cable (5184-1894) supplied with the router. This console cable is used in other ProCurve

switches such as the 5300xl series. The console port is a DB-9 DTE male connector.

Frame Relay Diagram

PPP over Fractional E1 Connection Diagram

Equipment Required

Note

This quick configuration guide provides step-by-step instructions for configuring

your application. The configuration script is available at the end of this document.

The configuration parameters used in the example outlined in this document are

for instructional purposes only. Please replace all underlined entries (example

)

with your specific parameters to configure your application.

Network Diagrams

Branch Office Corporate HQ

LAN IP: 10.10.10.1 /24

Network IP: 10.10.10.0

Network IP: 10.10.20.0

WAN IP: 192.168.72.2 /30

eth 0/1

LAN IP: 10.10.20.7 /24

DLCI 16

Annex D Signaling

192.168.72.1 /30

FR 1.x

e1 1/2

e1 1/1

PBX

Timeslots 1-15 Data,

17-31 Voice*

* Voice circuits require timeslot 16 for signaling. If voice is

required on the E1 1/2 G.703 port, the largest data map

which can be configured is timeslots 1-15 (leaving 17-31 for

voice) or 17-31 (leaving 1-15 for voice).

ProCurve Secure

Router 7102dl/7203dl

ProCurve Secure

Router 7102dl/7203dl

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Branch Office Corporate HQ

LAN IP: 10.10.10.1 /24

eth 0/1

LAN IP:

10.10.20.7 /24

WAN IP: 192.168.72.2 /30

Point-to-Point E1

Timeslots 1-15 Data,

Timeslots 17-31 Voice*

PPP Signaling

RIP V2

192.168.72.1 /30

PPP 1

e1 1/2

e1 1/1

PBX

* Voice circuits require timeslot 16 for signaling. If voice is

required on the E1 1/2 G.703 port, the largest data map which

can be configured is timeslots 1-15 (leaving 17-31 for voice) or

17-31 (leaving 1-15 for voice).

ProCurve Secure

Router 7102dl/7203dl

ProCurve Secure

Router 7102dl/7203dl

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Console

Power

Fault

Eth 0/1

Eth 0/2

Stat Stat

Slots

Bkp Bkp

Tx Tx

Rx Rx

Stat

Act

Test

dl dl

ProCurve 7203dl

Secure Router

J8753A

wide

Network IP: 10.10.10.0

Network IP: 10.10.20.0

Summary of content (12 pages)

PAGE 1
ProCurve Secure Router (with 1xE1 or 1xE1 + G.703 Modules) Quick Configuration Guide 5991-2117 April 2005 Equipment Required • Category 5 - UTP cable for connecting the system to the existing network. • VT100 terminal or PC with VT100 emulation software. • Serial cable (5184-1894) supplied with the router. This console cable is used in other ProCurve switches such as the 5300xl series. The console port is a DB-9 DTE male connector.
PAGE 2
Configure the Unit The ProCurve Secure Router may be initially accessed and managed via a console session. Refer to Initiate a Console Session for console session instructions. Initiating a Telnet session requires using a hub and two Ethernet cables (one for the PC and one for the unit). Refer to Configure Telnet Access on page 7 to configure Telnet session settings. Initiate a Console Session 1.
PAGE 3
Configure the E1 Network Interface 1. At the (config)# prompt, enter interface e1 1/1 to activate the interface configuration mode for the E1 network interface. 2. If necessary (this is the default), enter clock source line to configure the unit to recover clocking from the E1 network connection.
PAGE 4
Configure the G.703 Interface (Optional) 1. Enter interface e1 1/2 to activate the interface configuration mode for the G.703 network interface. 2. Enter ts16 to verify the G.703 interface is configured for voice signaling (timeslot 16 is used for signaling). 3. Enter no shutdown to activate the interface. 4. Enter exit to return to the Global Configuration mode.
PAGE 5
Bind the Interfaces 1. For Frame Relay applications, at the (config)# prompt, enter bind 1 e1 1/1 1 frame-relay 1 to connect the E1 network connection (e1 1/1) to the virtual Frame Relay interface (fr 1). or 2. For PPP applications, enter bind 1 e1 1/1 1 ppp 1 to connect the E1 network connection (e1 1/1) to the virtual PPP interface (ppp 1). Configure Static Routes Routes may be assigned either statically or dynamically. Continue with this section to create a static route.
PAGE 6
Configure Dynamic Routes Scenario 1: Dynamic Routing via OSPF 1. At the (config)# prompt, enter router ospf to activate the OSPF configuration mode. Your prompt should now display (config-ospf)#. 2. Specify the networks: Corporate HQ Router (config-ospf)#network 10.10.10.0 0.0.0.255 area 0 (config-ospf)#network 192.168.72.0 0.0.0.3 area 0 Branch Office Router (config-ospf)#network 10.10.20.0 0.0.0.255 area 0 (config-ospf)#network 192.168.72.0 0.0.0.3 area 0 3.
PAGE 7
Configure Telnet Access The following steps show how to access the Telnet configuration parameters and change the password. For this example, replace the underlined word with a password of your choosing. The ProCurve Secure Router supports five Telnet sessions (0 through 4). 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet session. Your prompt should now display (config-telnet-0-4)#. 3.
PAGE 8
! ETHERNET INTERFACE CONFIGURATION !*************************************************************! ! Enter the ethernet interface configuration mode. interface eth 0/1 ! ! Assign the ethernet port an IP address. ip address 10.10.20.7 255.255.255.0 ! ! Activate the interface to pass data. no shutdown ! ! Exit back to the global configuration mode. exit ! ! E1 INTERFACE CONFIGURATION !*************************************************************! ! Enter the E1 interface configuration mode.
PAGE 9
! FRAME RELAY VIRTUAL INTERFACE CONFIGURATION !************************************************************************! ! Create a Frame Relay virtual interface (labeled 1) and ! enter the Frame Relay interface configuration mode. interface fr 1 ! ! Your prompt should now display (config-fr1)#. ! ! Set the signaling mode. frame-relay lmi-type ansi ! ! Activate the interface to pass data. no shutdown ! ! Exit back to the global configuration mode.
PAGE 10
!Exit back to the global configuration mode exit ! ! BINDING THE INTERFACES - FRAME RELAY !*************************************************************! ! Connect the tdm group (1) on the e1 interface module to the ! virtual Frame Relay interface (fr 1). ! bind 1 e1 1/1 1 frame-relay 1 ! ! BINDING THE INTERFACES - PPP !*************************************************************! ! Connect the tdm group (1) on the e1 interface module to the ! virtual PPP interface (ppp 1).
PAGE 11
! CONFIGURING DYNAMIC ROUTES VIA OSPF !*************************************************************! ! Enter the OSPF configuration mode. router ospf ! ! Your prompt should now display (config-ospf)#. ! ! Specify the Corp HQ networks. network 10.10.10.0 0.0.0.255 area 0 network 192.168.72.0 0.0.0.3 area 0 ! ! Specify the Branch Office networks. network 10.10.20.0 0.0.0.255 area 0 network 192.168.72.0 0.0.0.3 area 0 ! ! Exit back to the global configuration mode.
PAGE 12
! CONFIGURE TELNET ACCESS !*************************************************************! ! Enter the Telnet configuration mode. line telnet 0 4 ! ! Your prompt should now display (config-telnet-0-4)#. ! ! Change the Telnet password. password WORD ! ! Exit back to the global configuration mode. exit ! ! SAVE THE CONFIGURATION !*************************************************************! ! Exit the global configuration mode. exit ! ! Your prompt should now display Router>.