Quick Start Guide A7000 dl 8xSerial Wide Module (J9011A) 2005-12

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-3792

ProCurve Secure Router dl 8xSerial Wide Module

J9011A

SPECIFICATIONS

Operating Mode Frame Relay/Multilink Frame Relay, PPP/Multilink PPP, HDLC

Serial Interface DTE only, no internal clock provided

Clocking up to 10 Mbps for each interface

Supported Standards: ISO 4903 (X.21), CCITT V.35 Synchronous (V.35)

Provides eight V.35 or X.21 (V.11) electrical interfaces

Connector: 26-Pin Smart Serial (DTE); additional adapter cables are

available for purchase to provide the V.35 DTE (J8757A) and X.21 DTE

(J8755A) interfaces

Compliance FCC Part 15 Class A, EN 55022 Class A, EN 55024,

EN 61000-3-2, EN 61000-3-3

ETSI TBR 1, ETSI TBR 2

EN 60950, UL/CUL 60950, AS/NZS 60950, IEC 60950

Physical Dimensions: 14.29 cm (5.63 in) W x 21.91 cm (8.63 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing at 30°C (86°C)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent, noncondensing at

30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

INSTALLATION INSTRUCTIONS

1. Remove power from the unit.

2. Slide the 8xSerial wide module into the wide option slot until the module is firmly

positioned against the chassis.

3. Secure the screws at both edges of the module.

4. Connect the cables to the associated device(s).

5. Complete the installation of the base unit.

6. Restore power to the unit.

SERIAL TO V.35 AND X.21 CABLES CONNECTION PINOUT

Serial

V.35

X.21

Pin Name

1P2 TD_A

2UN/A ETC_A

3 Y N/A TCLK_A

4V6 RCLK_A

5 R 4 RD_A

6 F N/A DCD_A

7HN/A DTR_A

8C3 RTS_A

9 N/A 10 RTS_B (V.11 only)

10 N/A 12 CTS_B (V.11 only)

11 D 5 CTS_A

12 E N/A DSR_A

13 K N/A TM_A

14 S 9 TD_B

15 W N/A ETC_B

16 AA N/A TCLK_B

17 X 13 RCLK_B

18 T 11 RD_B

19 N/A N/A Unused

20 N/A N/A Unused

21 N/A N/A Unused

22 N/A N/A Unused

23 N/A N/A Unused

24 N/A N/A Unused

25 N/A N/A Unused

26 B 8 Ground

Note

For safety information for the routers and all modules, please refer to

the safety and ESD precautions in the ProCurve Secure Router

Installation Guide included in your router shipment.

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5991-3792 ProCurve Secure Router dl 8xSerial Wide Module J9011A SERIAL TO V.35 AND X.21 CABLES CONNECTION PINOUT Serial Pin V.35 Pin X.21 Pin Name 1 P 2 TD_A 2 U N/A ETC_A 3 Y N/A TCLK_A 4 V 6 RCLK_A 5 R 4 RD_A 6 F N/A DCD_A 7 H N/A DTR_A 8 C 3 RTS_A 9 N/A 10 RTS_B (V.11 only) 10 N/A 12 CTS_B (V.
PAGE 2
Quick Start Guide 5991-3792 ProCurve Secure Router dl 8xSerial Wide Module J9011A 8XSERIAL MODULE COMMANDS description serial-mode [v35* | x21] Comment line to provide an identifier for this interface (for example, circuit ID, contact information, etc.). Specifies the electrical mode for the interface. All modes require the use of the appropriate cable: V.35 (J8757A), or X.21 (J8755A). Shows up to 80 alphanumeric characters.