Quick Start Guide A7000 dl ISDN BRI S/T Backup Module (J8461A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-2107

ProCurve Secure Router dl ISDN BRI S/T Backup Module

J8461A

PECIFICATIONS

Features Clear channel and bonding mode 1 call protocols

Network support for 64 kbps (1 B channel)

D-channel switch compatibility with AT&T 5ESS,

Northern Telecom DMS-100, National ISDN-1, and

Euro-ISDN

V.54 network loopback support

Compliance FCC Part 15 Class A, EN 55022 Class A, EN 61000-3-2,

EN 61000-3-3

ACIF S031, ETSI TBR 3

AS/NZS 60950, EN 60950

Physical Dimensions: 6.35 cm (2.5 in) W x 9.53 cm (3.75 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing at

30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

INSTALLATION INSTRUCTIONS

1. Remove power from the base unit.

2. If the ProCurve Secure Router interface module is already installed

in the ProCurve Secure Router chassis, remove all connected cables,

release the screws at both edges of the module front panel, and slide

the module out of the chassis.

3. Carefully align the P1 connector on the interface module with the

J1 connector on the backup module. Using only fingertip pressure

so that neither circuit board bends or flexes, ensure that the

connectors are firmly seated. Secure the backup module to the

interface module using the screws and standoff posts supplied.

4. Slide the interface module (with the backup module attached) into

the ProCurve Secure Router option slot until the module is firmly

seated against the chassis.

5. Secure the screws at both edges of the module.

6. Connect the cables to the associated device(s).

7. Complete installation of the base unit.

8. Restore power to the base unit.

ISDN BACKUP CONNECTION PINOUT

Pin Name Description

1-2 — Unused

3 R1 Network-Receive (Ring 1)

4 R Network-Transmit (Ring)

5 T Network-Transmit (Tip)

6 T1 Network-Receive (Tip 1)

7-8 — Unused

Note

For safety information for the routers and all modules,

please refer to the safety and ESD precautions in the

ProCurve Secure Router Installation Guide included

in your router shipment.

Eth 0/1

Eth 0/2

P/N: J8461A

PTC 231/05/001

SCT TEDHPRS05-249

REGULATORY MODEL: RSVLC-0407C

P/N: J8461A

PTC 231/05/001

SCT TEDHPRS05-249

REGULATORY MODEL: RSVLC-0407C

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5991-2107 ProCurve Secure Router dl ISDN BRI S/T Backup Module J8461A P/N: J8461A INSTALLATION INSTRUCTIONS 2 1. Remove power from the base unit. 2. If the ProCurve Secure Router interface module is already installed in the ProCurve Secure Router chassis, remove all connected cables, release the screws at both edges of the module front panel, and slide the module out of the chassis. 3.
PAGE 2
Quick Start Guide 5991-2107 ProCurve Secure Router dl ISDN BRI S/T Backup Module J8461A ISDN BRI S/T BACKUP MODULE COMMANDS alias isdn switch-type [basic-net3] Populates the ifAlias OID (Interface Table MIB of RFC2863) for this interface for use by the SNMP management station. Configures the unit to replace caller ID information with a user-specified number. Use the no form of this command to disable any caller ID overrides. Specifies the ISDN signaling type configured on the BRI interface.