Quick Start Guide A7000 ISDN BRI U Backup Module (J8460A) 2006-05

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Secure Router dl 1-port DS-3 Wide Module

Quick Start Guide 5991-2106

ProCurve Secure Router ISDN BRI U Backup Module

J8460A

SPECIFICATIONS

Features Clear Channel and Bonding Mode 1 call protocols

Network support for 64 kbps (1 B channel)

D-channel switch compatibility with AT&T 5ESS,

Northern Telecom DMS-100, and National ISDN-1

V.54 network loopback support

Compliance FCC Part 15 Class A, EN 55022 Class A,

EN 61000-3-2, EN 61000-3-3

ACTA/FCC Part 68, IC CS-03, UL/CUL 60950

Physical Dimensions: 6.35 cm (2.5 in) W x 9.53 cm (3.75 in) D

Operating Temperature: 0°C to 50°C (32°F to 122°F)

Relative Humidity: Up to 95 percent, noncondensing at

30°C (86°F)

Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)

Non-Operating Relative Humidity: Up to 95 percent,

noncondensing at 30°C (86°F)

Altitude: Up to 3.05 km (10,000 ft)

Eth 0/1

Eth 0/2

P/N: J8460A

US: PNBDENANJ8460

IC: 2250A-J8460

ITE

32F8

P/N: J8460A

US: PNBDENANJ8460

IC: 2250A-J8460

REGULATORY MODEL: RSVLC-0407C

ACCESSORY

I.T.E.

32F8

P/N: J8460A

US: PNBDENANJ8460

IC: 2250A-J8460

REGULATORY MODEL: RSVLC-0407C

ACCESSORY

I.T.E.

32F8

INSTALLATION INSTRUCTIONS

1. Remove power from the base unit.

2. If the ProCurve Secure Router interface module is already installed in

the ProCurve Secure Router chassis, remove all connected cables,

release the screws at both edges of the module faceplate, and slide

the module out of the chassis.

3. Carefully align the P1 connector on the interface module with the J1

connector on the ISDN BRI U backup module. Using only fingertip

pressure so that neither circuit board bends or flexes, ensure that the

connectors are firmly seated. Secure the backup module to the

interface module using the screws and standoff posts supplied.

4. Slide the ProCurve Secure Router interface module (with the backup

module attached) into the ProCurve Secure Router option slot until the

module is firmly seated against the chassis.

5. Secure the screws at both edges of the module.

6. Connect the cables to the associated device(s)

7. Complete installation of the base unit.

8. Restore power to the base unit.

ISDN BACKUP CONNECTION PINOUT

Pin Name Description

1-3 — Unused

4 R Network-Ring

5T Network-Tip

6-8 — Unused

Note

For safety information for the routers and all modules,

please refer to the safety and ESD precautions in the

ProCurve Secure Router Installation Guide included

in your router shipment.

Summary of content (2 pages)

PAGE 1
Quick Start Guide 5991-2106 ProCurve Secure Router ISDN BRI U Backup Module J8460A INSTALLATION INSTRUCTIONS Remove power from the base unit. 2. If the ProCurve Secure Router interface module is already installed in the ProCurve Secure Router chassis, remove all connected cables, release the screws at both edges of the module faceplate, and slide the module out of the chassis. 3. Carefully align the P1 connector on the interface module with the J1 connector on the ISDN BRI U backup module.
PAGE 2
Quick Start Guide 5991-2106 ProCurve Secure Router ISDN BRI U Backup Module J8460A ISDN BRI U BACKUP MODULE COMMANDS alias isdn switch-type [basic-5ess | basic-dms | basic-ni] Populates the ifAlias OID (Interface Table MIB of RFC2863) for this interface for use by the SNMP management station. Specifies the ISDN signaling type configured on the BRI interface. The type of ISDN signaling implemented on the BRI interface does not always match the manufacturer of the Central Office switch.