7500 20Gbps VPN Firewall Card Manual-6P103

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Switch xl Access Controller Module

Manual Version: 6P103-20130916 BOM:

3123A0MP

Part number: 5998-3445

HP 10500/11900/7500 20Gbps VPN Firewall module

(JG372A)

1 Module introduction

The LSU1FWCEA0 (JG372A) module integrates the firewall, VPN, content filtering, and NAT functions.

By installing an LSU1FWCEA0 (JG372A) module in a 10500/11900/7500 switch, you can provide

complete and reliable security protection for users, without changing the network topology.

Figure 1 LSU1FWCEA0 (JG372A) firewall module

2 Specifications

Figure 2 Front panel of the LSU1FWCEA0 (JG372A) module

(1) Console port (CONSOLE) (2)

USB

ports (hardware reserved, software not supported)

(3) 10/100/1000BASE-T copper combo port (4) 10/100/1000BASE-T copper combo port LED

(LINK/ACT)

(5) 1000BASE-X fiber combo port (6) 1000BASE-X

fiber combo port LED (LINK/ACT)

(7)

larm LED (ALM) (8)

System LED (RUN)

(9) Ejector lever (10) Captive screw

Table 1 Module specifications

Item S

ecification

Flash 4 MB

Memory

DDR3 SDRAM

2 memory slots

Standard: 16 GB (two 8-GB memory cards)

Summary of content (6 pages)

PAGE 1
Manual Version: 6P103-20130916 BOM: 3123A0MP Part number: 5998-3445 HP 10500/11900/7500 20Gbps VPN Firewall module (JG372A) 1 Module introduction The LSU1FWCEA0 (JG372A) module integrates the firewall, VPN, content filtering, and NAT functions. By installing an LSU1FWCEA0 (JG372A) module in a 10500/11900/7500 switch, you can provide complete and reliable security protection for users, without changing the network topology.
PAGE 2
Manual Version: 6P103-20130916 Item CF card BOM: 3123A0MP Part number: 5998-3445 Specification One built-in CF card slot Default: 256 MB Dimensions (H × W × D) 40.1 × 399.2 × 376.8 mm (1.58 × 15.72 × 14.83 in) Power consumption 109 W to 157 W Weight 3.9 kg (8.60 lb) Hot swapping Supported Interfaces • 1 console port • 2 USB ports (hardware reserved, software not supported) • 2 combo interfaces, which can operate in 10/100/1000BASE-T copper port mode or 1000BASE-X SFP fiber port mode at a time.
PAGE 3
Manual Version: 6P103-20130916 BOM: 3123A0MP Part number: 5998-3445 Item Specification Port transmission rate • 10 Mbps, half/full duplex • 100 Mbps, half/full duplex • 1000 Mbps, full duplex Table 4 1000BASE-X fiber port specifications Item Specification Transceiver module SFP Connector type LC Interface standard 802.3, 802.3u, and 802.3ab Module type Multi-mode short-haul (850 nm) Single mode medium-haul (1310 nm) Long-haul (1310 nm) Long-haul (1550 nm) Ultra-long-haul (1550 nm) Min.
PAGE 4
Manual Version: 6P103-20130916 BOM: 3123A0MP Part number: 5998-3445 4 Installing and removing the LSU1FWCEA0 (JG372A) module CAUTION: • Wear a well-grounded ESD-preventive wrist strap before you install or remove the module. • Do not touch the surface-mounted components directly with your hands when you install or remove the module. 4.1 Installing the LSU1FWCEA0 (JG372A) module 1. Face the front panel of the switch. 2.
PAGE 5
Manual Version: 6P103-20130916 BOM: 3123A0MP Part number: 5998-3445 4.2 Removing the LSU1FWCEA0 (JG372A) module 1. Use a Phillips screwdriver to loosen the captive screws at both sides of the module until all pressure is released. 2. Pull the ejector levers at both sides of the module outward, and pull the module along the guide rails until it completely comes out of the backplane. 3.
PAGE 6
Manual Version: 6P103-20130916 BOM: 3123A0MP Part number: 5998-3445 6.2 Upgrading software at the CLI Upgrade the software by using FTP/TFTP through the module's Ethernet port. 6.3 Upgrading software from the boot menu • Using XMODEM to upgrade software through the console port. • Using FTP/TFTP to upgrade software through the Ethernet port. 7 Obtaining documentation For software upgrade, see the HP Security Modules Software Upgrade Guide.