PCIe Analog Card and Digital Card Installation Instructions for SBM powered by Microsoft Lync 2010-10

ManualsBrandsHP ManualsComputer AccessoriesHP ProCurve Switch xl Access Controller Module

PCIe Analog Card (FXO or FXS) and Digital Card Installation Instructions

for the HP Extended Services zl Module

These instructions describe how to install analog and digital PCIe cards into the HP Extended Services zl Module. The HP Extended Services zl

Module has two PCIe slots and any of the available PCIe cards can be installed in either of the slots. Any combination of these cards can be used.

The following PCIe cards are available:

Installing an Analog PCIe Card

Read these instructions completely

before installing your PCIe Card.

• 4-Port FXS Analog Card (J9482A) • 1-Port T1/E1 Digital Card (J9487A)

• 4-Port FXO Analog Card (J9516A) • 2-Port T1/E1 Digital Card (J9488A)

• 2-Port FXO and 2-Port FXS Analog Card (J9518A) • 4-Port T1/E1 Digital Card (J9489A)

The FAX Synchronization Cable and the Power Cable Assembly are pre-installed on each Analog Card.

Note: The FAX Synchronization Cable is needed only when the Analog Card has FXS Ports to which a FAX machine is connected or may be

connected, and a Digital Card is also installed in the HP Extended Services zl Module. For all other configurations, the FAX Synchronization Cable

may be disconnected from the card, before proceeding.

Loosen the retaining screw and remove the slot cover from either

PCIe slot of the HP Extended Services zl Module. (The illustration

shows the card being installed in the upper slot, but either slot can

be used.) Also remove the plastic shield from the PCIe connector

on the module, if the shield is still present.

➊ Install the Analog Card

in the slot, and ➋ tighten retaining screw. Make sure the card is

plugged straight in to the PCIe connector.

➌ Connect the power cable on the Analog Card to either of the

power receptacles provided on the HP Extended Services zl

Module.

The Analog Card is now fully installed in the HP Extended

Services zl Module.

Power Cable Assembly

FAX Synchronization

Cable (the red edge is

closer to the card edge).

red edge

PCIe Connector

One end of the FAX Synchronization

Cable is still unconnected

Note: The HDD may not be

present in this location on

your module.

Summary of content (8 pages)

PAGE 1
Read these instructions completely before installing your PCIe Card. PCIe Analog Card (FXO or FXS) and Digital Card Installation Instructions for the HP Extended Services zl Module These instructions describe how to install analog and digital PCIe cards into the HP Extended Services zl Module. The HP Extended Services zl Module has two PCIe slots and any of the available PCIe cards can be installed in either of the slots. Any combination of these cards can be used.
PAGE 2
Installing a Digital PCIe Card red edge Loosen the retaining screw to remove the cover from the slot. ➊ If an Analog Card is installed in the other PCIe slot, connect the unconnected end of the FAX Synchronization Cable to the Digital Card, keeping the red edge closer to the card edge. ➋ Install the Digital card and ➌ tighten the retaining screw. Make sure the card is plugged straight in to the PCIe connector.
PAGE 3
Connecting the Network Cables For any analog connections, use the cables that ship with the PCIe cards. Note that there are two different connectors on these cables, a small handset-style connector, and a larger RJ11-style connector. Plug the handset-style connector into the FXS or FXO port on the PCIe card. Handset-style connector. RJ11-style connector. Plug the RJ11-style connector as follows: • For connections from FXS ports, plug in to devices such as phones and FAXes.
PAGE 4
EMC Regulatory Statements U.S.A: FCC Part 15 Notice This interface card complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference that may cause undesired operation. FCC Part 68 Requirements This interface card complies with Part 68 of the FCC rules. The FCC registration number is printed on the card.
PAGE 5
Telecom Homologation Mark Telepermit Statement: This Telepermit covers the digital connection to the network only, not the systems built around the card. Where the card is used as the interface to customer voice switching systems, the systems must be Telepermitted against PTC220.
PAGE 6
Electric Safety Statement WARNING: To reduce the risk of electric shock or damage to equipment, do not plug telecommunications lines into RJ-receptacles unless configured as a FXO port. Do not handle or connect telecommunications lines during a lightning storm. AVERTISSEMENT: Pour réduire les risques d’électrocution, ou de dommages matériels, ne branchez pas de lignes de télécommunications sur des prises RJ sauf si elles sont configurées en tant que port FXO.
PAGE 7
Declaration of Conformity 7
PAGE 8
© Copyright 2010, 2011 Hewlett-Packard Development Company, LP. All rights reserved. The information contained herein is subject to change without notice. This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard. Part Number: 5998-2398 June 2011 Printed in Canada Technical information in this document is subject to change without notice.