HP ProLiant BL e-Class Integrated Administrator User Guide May 2003 (Fourth Edition) Part Number 249070-004 HP CONFIDENTIAL Writer: Amy Clute File Name: a-frnt.
© 2003 Hewlett-Packard Development Company, L.P. Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such products.
Contents About This Guide Audience Assumptions...................................................................................................... ix Important Safety Information ............................................................................................ ix Symbols on Equipment ..................................................................................................... ix Symbols in Text.............................................................................................
Contents Additional Steps.............................................................................................................2-11 Help................................................................................................................................2-11 Chapter 3 Web-Based User Interface Accessing the Web-Based User Interface........................................................................3-2 Web-Based Navigation ................................................................
Contents General Commands................................................................................................... 4-3 General Management Commands............................................................................. 4-4 User Account Commands ......................................................................................... 4-7 Enclosure Network Configuration Commands ....................................................... 4-12 Enclosure Management Commands .........................
Contents Powering Off the Server Blade .................................................................................6-7 Identifying a Server Blade Using the Unit Identification LED .................................6-9 Managing the Enclosure ................................................................................................6-11 Reviewing the Activity of the Enclosure.................................................................
Contents Appendix C Troubleshooting Appendix D Event Details Appendix E Factory Default Settings Enclosure .........................................................................................................................E-2 Users................................................................................................................................E-2 Groups .............................................................................................................................
About This Guide This guide provides step-by-step instructions for operation, and reference information for advanced operation, troubleshooting, and future upgrades for the HP ProLiant BL e-Class Integrated Administrator. Audience Assumptions This guide is intended for users with access to the ProLiant BL e-Class Integrated Administrator. It assumes that the server blade system hardware is installed, and that the user has minimal experience working with server blade systems.
About This Guide This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel. This symbol indicates the presence of electric shock hazards. The area contains no user or field serviceable parts. Do not open for any reason.
About This Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
About This Guide Related Documents For additional information on the topics covered in this guide, refer to the following documentation: • HP ProLiant BL e-Class System Maintenance and Service Guide • HP ProLiant BL e-Class System Hardware Installation and Configuration poster • ProLiant Integration Module for Altiris eXpress User Guide • HP Servers Troubleshooting Guide • HP ROM-Based Setup Utility Guide • HP ProLiant BL e-Class C-GbE Interconnect Switch User Guide • White paper: HP ProLiant
About This Guide Be sure to have the following information available before you call HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number • Applicable error messages • Add-on boards or hardware • Third-party hardware or software • Operating system type and revision level HP Website The HP website has information on this product as well as the latest drivers and flash ROM images. You can access the HP website at www.hp.com.
1 HP ProLiant BL e-Class System Software Features The HP ProLiant BL e-Class system offers an extensive set of features and optional tools to support effective server management and software deployment. This chapter describes the Integrated Administrator and provides a brief overview of software associated with the system. ProLiant BL e-Class Integrated Administrator The Integrated Administrator is a centralized management and monitoring system for the ProLiant BL e-Class enclosure and server blades.
HP ProLiant BL e-Class System Software Features For further information associated with the Integrated Administrator, refer to: www.compaq.com/products/servers/proliant-bl/e-class/integrated-admin.html Integrated Administrator Features The Integrated Administrator provides the following functionality to deliver state-of-the-art management of the enclosure and server blades: • Dedicated LAN network connectivity Each Integrated Administrator provides a dedicated network connection.
HP ProLiant BL e-Class System Software Features If a server blade does not respond, this feature enables an administrator to initiate a cold reboot to bring the server blade back online. The Integrated Administrator can be used to remotely operate a power button of a server blade. Integrated Administrator is fully accessible by means of Microsoft® Internet Explorer and Netscape. This capability enables easy access to the features of Integrated Administrator.
HP ProLiant BL e-Class System Software Features • Automatic network configuration The Integrated Administrator provides automatic network configuration of the IP address and host name using Dynamic Host Configuration Protocol (DHCP) and Dynamic DNS/WINS. Integrated Administrator comes with a default name and DHCP client that leases an IP address from the DHCP server on the network. For networks that do not use DHCP, the Integrated Administrator enables static IP configuration.
HP ProLiant BL e-Class System Software Features For more information on the Insight Manager 7 utility, refer to the ProLiant Essentials Foundation Pack documentation that ships with the system or refer to: www.hp.com/servers/rdp • Event Notification The Integrated Administrator provides real-time event notifications for an enclosure. When an event occurs, the Integrated Administrator notifies connected users by generating an icon that the user can click to view more details.
HP ProLiant BL e-Class System Software Features • ProLiant Essentials Rapid Deployment Pack (Option) The Rapid Deployment Pack features a graphical deployment console, which provides intuitive drag-and-drop events, such as scripts and images, to deploy the operating systems and applications on any combination of server blades installed in the enclosures.
HP ProLiant BL e-Class System Software Features • Health and Wellness Driver (server blade health driver) and Integrated Management Log (IML) Viewer The server blade health driver monitors operational data of the server blades and logs abnormal conditions. This log is accessible by utilities, including Insight Manager 7, and supports the HP Management Agents.
HP ProLiant BL e-Class System Software Features The interconnect switch is compatible with industry standards and has full for support for IEEE 802.1Q VLANS. 1-8 HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: b-ch1 System Software Features.
2 Getting Started The Integrated Administrator enables monitoring and management of all functions within an enclosure, including functions specific to the server blades housed within it. Once configured, the Integrated Administrator provides these features through both a Web-based user interface and CLI.
Getting Started • If the network uses Dynamic DNS or WINS, you can access the Integrated Administrator using the factory-configured host name. IMPORTANT: The preconfigured Administrator password and host name are displayed on the Integrated Administrator Default Network Settings Tag (settings tag) attached to the interconnect tray. • If the network uses DHCP, an IP address can be automatically assigned to the Integrated Administrator.
Getting Started 1 2 3 4 5 6 7 Figure 2-1: Rear panel Integrated Administrator components Table 2-1: Rear Panel Integrated Administrator Components Item Description 1 Management (10/100 Ethernet) connector for remote access through a Web-based user interface, Telnet, or Secure Shell 2 Integrated Administrator reset button 3 Console (serial) connector for local access to the command line interface using a laptop computer 4 Integrated Administrator health LED 5&6 7 Enclosure link connectors
Getting Started Determining the Integrated Administrator’s Initial IP Address HP recommends that you connect a local client device, such as a laptop computer, to the console (serial) connector in order to determine the initial IP address used by the network to recognize the Integrated Administrator. After using that IP address to access the Integrated Administrator locally using the console (serial) connector, you can use the Integrated Administrator default values to complete the initial configuration.
Getting Started Default Values for the Integrated Administrator The Integrated Administrator is configured with a default user name, password, and DNS name. A settings tag with the preconfigured values is attached to the interconnect tray containing the Integrated Administrator module. IMPORTANT: For security reasons, HP recommends changing the Administrator password when accessing Integrated Administrator for the first time.
Getting Started b. Open a terminal emulation session with the following settings: 9600 bps, 8 data bits, no parity, and 1 stop bit. c. Log into the Integrated Administrator using the password on the settings tag attached to the interconnect tray. 2. Establish the Integrated Administrator IP address. For a detailed explanation of the command line conventions used in this document, see Appendix A, “Command Line Conventions.
Getting Started Setting Up the Web-Based User Interface To set up the Web-based user interface: 1. Enter the Integrated Administrator IP address or DNS name in the address bar of the Web browser. A security alert appears as an expected part of this procedure. Figure 2-3: Certificate Security Alert — If you click Yes, the browser continues to the Login window of Integrated Administrator. The alert message appears each time you access the Integrated Administrator management processor in a browser.
Getting Started NOTE: To install your own certificate onto the Integrated Administrator rather than the automatically generated certificate, see the information on certificate-related commands in Table 4-8 as well as the “Administering Security Certificates” section in Chapter 7, “Performing Advanced Functions.” Figure 2-4: Certificate Information window IMPORTANT: If the certificate is removed from your browser, the security alert message is displayed again.
Getting Started 2. Install the certificate to your browser: a. Click Install Certificate. The Certificate Manager Import Wizard starts. b. Click Next. c. Click Next for the browser to automatically select the certificate store when the Certificate Store window appears. d. Click Finish when the Completing the Certificate Manager Import Manager Wizard window displays. e. Click Yes to confirm the installation of the certificate when the confirmation window displays. 3.
Getting Started After the default user name and password have been verified, the summary window appears. Figure 2-6: Integrated Administrator summary window The Integrated Administrator summary window provides general information about the Integrated Administrator, such as the user currently logged on, enclosure name and status, and Integrated Administrator IP address and name.
Getting Started Additional Steps HP recommends performing the following tasks: • Change the Administrator password • Set the date and time • Name the enclosure and rack • Set up groups, users, and access privileges For detailed instructions on performing these tasks, see the appropriate sections in Chapter 5, “Setting Up the System.” Help Additional assistance is available by means of the Integrated Administrator help option.
3 Web-Based User Interface This chapter provides information for navigating the Integrated Administrator Web-based user interface. NOTE: Values appearing in the screens of this chapter are for illustrative purposes only. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Accessing the Web-Based User Interface IMPORTANT: Accessing the Web-based user interface is not supported from the console (serial) connector. To access the Integrated Administrator Web-based user interface with HTTP: 1. Get the DNS name from the settings tag attached to the interconnect tray. 2. Open a Web browser and enter the IP address or DNS name for the enclosure you wish to access.
Web-Based User Interface Web-Based Navigation The Web-based user interface displays information and receives input in the following areas: • Top panel • Left panel • Deck panel Top Panel Figure 3-2 illustrates the location of the top panel. Figure 3-2: Top panel of the Web-based user interface HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface The top panel information is displayed at all times, including the following items: • Enclosure name • Current user • Tabs The Integrated Administrator top panel provides real-time event notifications for an enclosure according to two categories: caution and critical.
Web-Based User Interface Left Panel Figure 3-3 illustrates the location of the left panel. Figure 3-3: Left panel of the Web-based user interface The left panel displays which screens are available under each tab. Information appearing in the left panel depends on which tab the user chooses from within the top panel. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Deck Panel Figure 3-4 illustrates the location of the deck panel. Figure 3-4: Deck panel of the Web-based user interface The deck panel displays the areas of information provided by the available screens under each tab. Information appearing in the deck panel depends on the option chosen by the user from within the top panel and the left panel.
Web-Based User Interface • Virtual Buttons • System Log Enclosure Information IMPORTANT: All users have read access to the information in this screen. Figure 3-5 illustrates the information presented on the Enclosure Information screen.
Web-Based User Interface Two buttons appear on the Enclosure Information screen: • Apply — Saves changes made to the screen • Cancel — Restores all fields on the screen to their original values Table 3-2 describes the information displayed in the areas that comprise the Enclosure Information screen.
Web-Based User Interface Table 3-2: Enclosure Information Screen continued Field Possible Values Description Temperature OK, Warm, Caution, or Critical Enclosure component temperature sensor Redundant or Non-redundant Redundant: both power supplies are functional. Power Area Power Subsystem Status Non-redundant: one power supply is missing or not functional.
Web-Based User Interface Table 3-2: Enclosure Information Screen continued Field Possible Values Description General Area, continued Interconnect Tray Type ProLiant BL e-Class C-GbE Interconnect Switch Type of interconnect tray ProLiant BL e-Class RJ-21 Interconnect ProLiant BL e-Class RJ-45 Interconnect Interconnect Tray Part Number Part number for the interconnect tray Interconnect Tray Spare Number Spare number for the interconnect tray Interconnect Tray Serial Number Serial number for the in
Web-Based User Interface Table 3-2: Enclosure Information Screen continued Field Possible Values Description Drop-down box with standard time zones listed Time zone assigned to the enclosure Date and Time Area* Time Zone For the default time zone, see Appendix E, “Factory Default Settings.” For a list of all supported time zones, see Appendix F, “Time Zone Settings.
Web-Based User Interface If you select Other for time zone, use the following window to set a user-defined time zone: Figure 3-6: User-defined time zone window Three buttons appear on this window: • Apply — Applies the new time zone • Reset — Clears the time zone text box • Cancel — Cancels all changes and closes the window For more information on accepted time zones, refer to Appendix F, “Time Zone Settings”.
Web-Based User Interface Network Configuration IMPORTANT: Only enclosure administrators have access to these settings. Figure 3-7 illustrates the information presented on the Network Configuration screen. Figure 3-7: Network Configuration screen (information and protocols areas, 1 and 2 of 3, shown) The Network Configuration screen enables the enclosure administrator to modify the network settings of an enclosure.
Web-Based User Interface CAUTION: Both the Web and Secure Shell protocols must be enabled to allow access to the Web-based user interface. Table 3-3 describes the information displayed in the areas that comprise the Network Configuration screen.
Web-Based User Interface Table 3-3: Network Configuration Screen continued Field Possible Values Description Network Area, continued Subnet Mask ###.###.###.###, where ### ranges from 0 to 255 Subnet mask for the Integrated Administrator (mandatory if Static IP is selected) Gateway Address ###.###.###.###, where ### ranges from 0 to 255 Gateway address for the Integrated Administrator (optional field if Static IP is selected) DNS Server 1 ###.###.###.
Web-Based User Interface SNMP Configuration IMPORTANT: Only enclosure administrators have access to these settings. Figure 3-8 illustrates the information presented on the SNMP Configuration screen. Figure 3-8: SNMP Configuration screen The SNMP Configuration screen enables an enclosure administrator to modify the SNMP settings of an enclosure. These settings are specific to the enclosure and do not affect the network configurations for server blades.
Web-Based User Interface Table 3-4 describes the information presented on the SNMP Configuration screen: Table 3-4: SNMP Configuration Screen Field Possible Values Description System Information Area SNMP Status Enabled or Disabled System Name Displays if SNMP is enabled or disabled The name of the enclosure System Location System Contact Up to 20 characters including all alphanumeric, dash, underscore, and space characters The SNMP location of the enclosure Up to 20 characters including all alp
Web-Based User Interface Table 3-4: SNMP Configuration Screen continued Field Possible Values Description Community Strings And Trap Destinations Area, continued Write Community Up to 20 characters including all alphanumeric, dash, and underscore characters Sets the SNMP write community string If this is left blank, SNMP SET commands are disabled. For the default Read community string, see Appendix E, “Factory Default Settings.
Web-Based User Interface Virtual Buttons IMPORTANT: Only enclosure administrators can execute these commands. Figure 3-9 illustrates the information presented on the Virtual Buttons screen. Figure 3-9: Virtual Buttons screen (Enclosure tab) The Virtual Buttons screen enables an enclosure administrator to modify the power state of the enclosure and Unit Identification LED from a remote location in order to facilitate troubleshooting by technicians in the data center.
Web-Based User Interface Figure 3-10: Virtual Buttons screen (Enclosure Power area) You can select the appropriate function with the following buttons: • Restart Integrated Administrator restarts the Integrated Administrator and does not affect the server blades. IMPORTANT: Click Restart Integrated Administrator only at the direction of HP support personnel. You must click Apply for these settings to take effect.
Web-Based User Interface System Log The System Log screen provides an enclosure administrator with a chronological list of events and fixes associated with the enclosure.
Web-Based User Interface Bays Tab The Bays tab provides access to the following screens: • Bay List • Bay Information • Remote Console • Virtual Buttons • Console Log Bay List The Bay List screen enables an enclosure administrator to observe and update the assignment of groups to server blade bays, as well as monitor the status of each server blade installed in the enclosure. Group administrators and group members with permissions can view the server blade bays assigned to their groups.
Web-Based User Interface Figure 3-12 and Table 3-5 describe the information presented in the Bay List screen: Figure 3-12: Bay List screen HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Table 3-5: Bay List Field Descriptions Field Possible Values Description Bay # 1-20 Server blade bay number UID Field Displays a blue circle if the unit identification (UID) LED of the blade is lit Server Blade Name Name of the server blade in that server blade bay as defined by the operating system of the server blade Note: Without the server blade health driver properly installed, the Integrated Administrator cannot obtain the server blade name.
Web-Based User Interface Figure 3-13: Bay Assignment dialog box The Action radio buttons (Assign/Unassign) determine what action to take when you click OK. IMPORTANT: If you wish to reassign a server blade from one group to another, you must first unassign the server blade; otherwise the command does not execute. The Assign to Group drop-down box contains all groups within the enclosure to determine the group with ownership of the server blade bay.
Web-Based User Interface Bay Information IMPORTANT: Be sure the Integrated Administrator displays up-to-date server blade information by rebooting the server blade after installing the server blade health driver. Figure 3-14 illustrates the information presented on the Bay Information screen. Figure 3-14: Bay Information screen (bay 5 shown) The Bay Information screen enables an enclosure administrator to observe the status and general information for a server blade in a given server blade bay.
Web-Based User Interface Table 3-7: Bay Information Screen Field Possible Values Description Status Area Bay Number Bay number Server Blade Name Name of the server blade as specified with the server blade operating system Status OK, Degraded, or Failed Status of the server blade Thermal Condition OK, Warm, Caution, or Critical Thermal condition of the blade Enclosure Name Name of enclosure For the default enclosure name, see Appendix E, “Factory Default Settings.
Web-Based User Interface Table 3-7: Bay Information Screen continued Field Possible Values Description NIC #1 and #2 MAC Addresses ##:##:##:##:##:##, where ## ranges from 00 to FF.
Web-Based User Interface Figure 3-15 illustrates the information presented on the Remote Console screen. Figure 3-15: Remote Console screen (bay 5 shown) For information on establishing remote console connectivity, see the “Enabling Remote Console Sessions to Server Blades” section in Chapter 5, “Setting Up the System.” HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Virtual Buttons Figure 3-16 illustrates the information in the Virtual Buttons screen. Figure 3-16: Virtual Buttons screen (bay 5 shown) Enclosure administrators and group administrators with permissions can use the Virtual Buttons screen to modify the state of the power state and Unit Identification LED of a server blade in order to facilitate troubleshooting from a remote location.
Web-Based User Interface • You can select the appropriate function in the Server Blade Power area using the following radio buttons: — Reboot reboots the server blade. — Power Off attempts a graceful shutdown of the server blade for 5 minutes, after which time this command powers down the server blade immediately. — Power Off Immediately powers off the server blade forcefully.
Web-Based User Interface Administration Tab IMPORTANT: For an explanation of user rights associated with the Integrated Administrator, see the “User Permissions” section in Chapter 5, “Setting Up the System.
Web-Based User Interface User List Figure 3-17 illustrates the information presented in the User List screen. Figure 3-17: User List screen The User List screen enables an appropriate group administrator or enclosure administrator to observe and update user access to groups and server blade bays. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Please note the following permissions related to the action buttons of the User List screen (Table 3-8). Table 3-8: User List Action Buttons and Permissions Button Function Permissions View/Modify User Opens the View/Modify User screen Enclosure administrators can access and modify the information for any user. Users can access and modify the information for their own account.
Web-Based User Interface Group List Figure 3-18 and Table 3-10 describe the information presented in the Group List screen. Figure 3-18: Group List screen The Group List screen enables an enclosure administrator to observe and update the assignment of groups and users to server blade bays. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: d-ch3 Web-Based User Interface.
Web-Based User Interface Two buttons appear on this screen: • View/Modify Group—Opens the View/Modify Group screen • Remove Group—Removes the selected group IMPORTANT: Enclosure administrators can view and modify the information for all groups. Group administrators and group members can view the information for the groups in which they are members.
Web-Based User Interface Figure 3-19 and Table 3-11 describe the information presented in the User Account area of the Add User screen: Figure 3-19: Add User screen (User Account area, 1 of 2, shown) The Add User screen enables an enclosure administrator to create a user profile, including group and server blade bays assignments.
Web-Based User Interface Table 3-11: Add User Screen Field Possible Values Description 1-13 characters including alphanumeric, dash, and underscore characters Login name of the user. User Account Area User Name The user name must begin with a letter. A maximum of 25 users can be created in addition to the reserved accounts. Note: “Administrator, “switcha,” “switchb,“ and “all” are reserved names and cannot be used. This restriction is not case-sensitive.
Web-Based User Interface Table 3-11: Add User Screen continued Field Possible Values Description Group Membership Area Group Names All groups are listed. A list of all possible groups Group Membership X number of groups (all groups in which the user has membership) A list of all users that are members of the group Add User [View] >>> Adds the user to the selected groups in the Group Names text box with View rights for group members These groups appear in the Group Membership textbox.
Web-Based User Interface Figure 3-20 illustrates the information presented in the Add Group screen. Figure 3-20: Add Group screen (Group Information and Bay Assignment areas, 1 and 2 of 3, shown) IMPORTANT: Grayed-out checkboxes are unavailable because they are already assigned to another group. The Add Group screen enables an enclosure administrator to create a group profile, including user and server blade bays assignments.
Web-Based User Interface Table 3-12: Add Group Screen Field Possible Values Description Group Information Area Group Name 1-13 characters including alphanumeric, dash, and underscore characters Name of group The group name must begin with a letter. A maximum of 20 groups can be created.
Web-Based User Interface Table 3-12: Add Group Screen continued Field Possible Values Description Group Membership Area, continued Add User [View] >>> Adds selected users in the User Names text box to the group with View rights for group members Users lose View/Modify rights for group administrators if they previously had them.
Web-Based User Interface Event List Tab IMPORTANT: The Event List differs from the System Log in the following ways: • Any user can view the Event List. Only enclosure administrators can access the System Log. • The messages in the Event List are limited to cautions and critical failures. Refer to the enclosure System Log for information on both failures and fixes. • The Event List only displays messages received since the user logged into the Integrated Administrator.
Web-Based User Interface Figure 3-21 illustrates the information presented in the Event List screen. Figure 3-21: Event List screen (fan failure shown) The Event List provides the following information for each event: • Severity • Source • Date • Time • Event Details For detailed information regarding the Event List, including a comprehensive list of event messages, see Appendix D, “Event Details.
Web-Based User Interface Interconnect Tab Figure 3-22 illustrates the information presented in the Interconnect Tray screen: Figure 3-22: Interconnect Tray screen The Interconnect Tray screen allows anyone to view information about the interconnect tray. It allows enclosure administrators to connect to the remote console of one of the interconnect switches if installed. Table 3-14 describes the information displayed in the areas that comprise the Interconnect Tray screen.
Web-Based User Interface Table 3-14: Interconnect Tray screen continued Field Possible Values Description Temperature OK, Warm, Caution, or Critical Thermal status of the interconnect tray Switch A Status OK, Degraded, or Failed Status of Switch A. This will only be displayed if an interconnect switch is installed. Switch B Status OK, Degraded, or Failed Status of Switch B. This will only be displayed if an interconnect switch is installed.
4 Command Line Interface This chapter provides reference material for operating the Integrated Administrator CLI.
Command Line Interface Accessing the Command Line Interface You can access the CLI remotely through the management (10/100 Ethernet) connector or locally through the console (serial) connector on the rear panel of the enclosure. Accessing Remotely through the Management Connector To access the Integrated Administrator command line interface remotely through the management (10/100 Ethernet) connector: 1. Get the default host name from the settings tag attached to the interconnect tray. 2.
Command Line Interface Operating the Command Line Interface General Commands Table 4-1: General Commands Command Description Restrictions CLEAR SCREEN Clears the terminal screen None EXIT Exits the command line interpreter None HELP If a command is given, the usage and help text for the command are shown. If TREE is given, all commands are shown in a tree format. If no argument is given, all base commands are displayed.
Command Line Interface General Management Commands Table 4-2: General Management Commands Command Description Restrictions CLEAR SESSION SWITCH [A | B] Terminates a Terminal session from the enclosure. Group administrators may only execute this command for server blade bays to which they have access. CLEAR SSHKEY Removes the contents of the Secure Shell authorized keys file. After performing this command, you will not be able to login using public key-based authentication.
Command Line Interface Table 4-2: General Management Commands continued Command Description Restrictions GENERATE CERTIFICATE REQUEST Generates a PKCS#10 certificate request. Only enclosure administrators may execute this command. GENERATE CERTIFICATE SELFSIGNED Generates a self-signed certificate. Only enclosure administrators may execute this command. PING {} [ | ] Sends ICMP echo messages to a remote IP device. If is omitted, only 5 packets are sent.
Command Line Interface Table 4-2: General Management Commands continued Command Description Restrictions SHOW EXPERT {MODE}: Displays the current EXPERT MODE setting for the current user. None SHOW SESSIONS Displays the connection to each bay and switch if one exists. Users may not run this command. Group members and group administrators may only see the sessions for bays assigned to groups to which they belong. Enclosure administrators see all sessions.
Command Line Interface User Account Commands Table 4-3: User Account Commands Command Description Restrictions ADD GROUP Adds a group to the system Only enclosure administrators may execute this command. The default group description is blank. A maximum of 20 groups may be added to the system. The must be unique to all other group names and user names and is casesensitive.
Command Line Interface Table 4-3: User Account Commands continued Command Description Restrictions ASSIGN ADMINISTRATO R {RIGHTS} Promotes a user to have enclosure administrator permissions Only enclosure administrators may execute this command. ASSIGN BAY [ALL | {[ , | -] }] Assigns one or more bays to a group Only enclosure administrators may execute this command.
Command Line Interface Table 4-3: User Account Commands continued Command Description Restrictions REMOVE USER [ALL | ] Removes a user from the system Only enclosure administrators may execute this command. If ALL is specified, the command is run for all users except the default system accounts. The is case-sensitive. The “Administrator,” “switcha,” and “switchb” accounts cannot be removed. SET GROUP {DESCRIPTION } Sets a group’s description.
Command Line Interface Table 4-3: User Account Commands continued Command Description Restrictions SET USER CONTACT {} If no exists, the command modifies the contact info of the user that executed the command. Only enclosure administrators may modify another user’s contact information. The is case-sensitive. The must be 0-20 characters long and can include all alphanumeric characters, the dash, the underscore, and spaces.
Command Line Interface Table 4-3: User Account Commands continued Command Description Restrictions SHOW GROUP [ | ALL] Displays the group’s description, a list of members with View permission, a list of members with View/Modify permission, number of bays, and a list of each of the bays the group manages. Group members and group administrators only see the groups in which they have membership. Users may not execute this command.
Command Line Interface Enclosure Network Configuration Commands Table 4-4: Enclosure Network Configuration Commands Command Description Restrictions ADD SNMP TRAPRECEIVE R Adds an IP address to receive SNMP traps. Only enclosure administrators may execute this command. Only v1 traps are supported. Traps are directed to the SNMP default port, 162. A maximum of 8 IP address may be added to receive SNMP traps. The must be in the form ###.###.###.
Command Line Interface Table 4-4: Enclosure Network Configuration Commands continued Command Description Restrictions DOWNLOAD CONFIG Downloads a previously saved configuration file from a specific IP host Only enclosure administrators may execute this command. The files are auto-executed in script mode. The file is not allowed to change the password of the “Administrator” account. Supported protocols are http, ftp, and tftp. The URL should be formatted as protocol://host/path/file.
Command Line Interface Table 4-4: Enclosure Network Configuration Commands continued Command Description Restrictions SET GATEWAY Sets the network default gateway Only enclosure administrators may execute this command. SET IPCONFIG [DHCP {DYNAMICDNS } | STATIC ] Sets up the Integrated Administrator IP configuration Only enclosure administrators may execute this command. The gateway and DNS addresses are cleared.
Command Line Interface Table 4-4: Enclosure Network Configuration Commands continued Command Description Restrictions SET SNMP LOCATION Configures the SNMP location of the enclosure. Only enclosure administrators may execute this command. The default location is blank. The must be 0-20 characters long and includes all alphanumeric characters, the underscore, the dash, and the space. If spaces are part of this information, enclose the information in quotes.
Command Line Interface Enclosure Management Commands Table 4-5: Enclosure Management Commands Command Description Restrictions CLEAR SYSLOG ENCLOSURE Clears the enclosure system log Only enclosure administrators may execute this command. Once deleted, this information cannot be restored. POWEROFF ENCLOSURE {FORCE} Performs a graceful shutdown of the enclosure. Each blade is first gracefully shutdown. If the FORCE argument is given, the enclosure and all blades are immediately shutdown.
Command Line Interface Table 4-5: Enclosure Management Commands continued Command Description Restrictions SET ENCLOSURE ASSET {TAG} Changes the enclosure asset tag Only enclosure administrators may execute this command. The must be 1-31 characters long and includes alphanumeric, dash, and underscore characters. The default enclosure asset tag is blank. To set a blank asset tag, specify the blank value using quotes.
Command Line Interface Table 4-5: Enclosure Management Commands continued Command Description Restrictions SHOW DATE Displays the current date, time, and time zone of the internal clock of the enclosure. None SHOW DISPLAY EVENT Displays whether event notification is on or off. None SHOW ENCLOSURE FAN [ | ALL] Displays the status, redundancy, partner, speed, and part number for the requested fan.
Command Line Interface Table 4-5: Enclosure Management Commands continued Command Description Restrictions SHOW ENCLOSURE TEMP Displays the locale, status (OK, warm, degraded, or failed), temperature in degrees Fahrenheit, and temperature in degrees Celsius for all temperature sensors. None SHOW RACK NAME Shows the name for the rack where the enclosure resides. None SHOW SYSLOG ENCLOSURE Displays the syslog of the enclosure with 22 lines per screen.
Command Line Interface Table 4-5: Enclosure Management Commands continued Command Description Restrictions UPLOAD CONFIG Uploads the current runtime configuration to the specified FTP or TFTP server. Only enclosure administrators may execute this command.
Command Line Interface Table 4-6: Server Bay Management Commands continued Command Description Restrictions GENERATE NMI Generates an NMI on the specified blade. Only enclosure and group administrators may execute this command. The consequences of an NMI are operating system specific. POWEROFF BAY {[ , | - ] } {FORCE} Performs a graceful shutdown of the server blade in the specified bay.
Command Line Interface Table 4-6: Server Bay Management Commands continued Command Description Restrictions REBOOT BAY {[ , | - ] } {FORCE} {[PXE | HDD | RBSU]} Sends a request to the server blade to perform a graceful shutdown. Only enclosure and group administrators may execute this command. The server blade is then powered on. If no server blade is in the specified bay, the user is told that the bay is empty.
Command Line Interface Table 4-6: Server Bay Management Commands continued Command Description Restrictions SET BAY UID {[ , | - ] } [ON | OFF] Turns a Unit Identification LED on the server blade on or off. Only enclosure and group administrators may execute this command.
Command Line Interface Table 4-6: Server Bay Management Commands continued Command Description Restrictions SHOW SYSLOG BAY Displays the syslog of the specified blade with 22 lines per screen. Group members and group administrators only see information for the bays in their groups. Typing “q” quits the command; any other key shows the next screen if more information is available to display.
Command Line Interface Command Line Event Messages Table 4-7: Command Line Event Messages Message Possible Cause User Event Messages User Permission Change One of the following has occurred: • A user has been added, removed, or modified. • A user’s group membership has been modified. The server blade bay membership has been changed for a group with at least one user. Enclosure Event Messages Enclosure Shutdown The enclosure is being shutdown.
Command Line Interface Table 4-7: Command Line Event Messages continued Message Possible Cause Bay Event Messages Bay Event A server blade bay has been assigned or unassigned from a group. Blade Inserted A server blade was inserted into the enclosure. Blade Removed A server blade was removed from the enclosure. Blade Status Change Health driver detected a change in status due to a change in the state of one or more hardware components or server blade readings.
Command Line Interface Functionality Exclusive to the Command Line Interface Table 4-8 identifies functions or capabilities available to the command line interface and unavailable when using the Web-based user interface. Table 4-8: Functionality Exclusive to the Command Line Interface Function Description Capability Exclusive to the Command Line Interface Pauses the sessions for a fixed period of time. Useful for adding delays to scripts. The field can be any whole number from 1 – 86400.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface General Management Commands, continued DOWNLOAD CERTIFICATE Downloads a CA supplied PKCS#7 file to replace the current security certificate on the system. All Supported protocols are http, ftp, and tftp. The URL should be formatted as protocol://host/path/file.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface General Management Commands, continued PING {} [ | ] Sends ICMP echo messages to a remote IP device SET DISPLAY EVENTS [ON | OFF] Turns event notification on or off SET EXPERT {MODE} [ON | OFF] Turns EXPERT MODE on or off.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface General Management Commands, continued SET SCRIPT MODE [ON | OFF] When SCRIPT MODE is on, all prompting and verifications of entries cease. All If SCRIPT MODE is on, the following commands require a password argument: ADD USER, SET USER PASSWORD, or SET PASSWORD.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface General Management Commands, continued DOWNLOAD CONFIG Downloads a previously saved configuration file from a specific IP host. All The file is auto-executed in SCRIPT MODE. The file is not allowed to change the password of the “Administrator” account. Supported protocols are http, ftp, and tftp.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface Enclosure Management Commands, continued SHOW ENCLOSURE POWERSUPPLY [ | ALL] Displays the status of the power supply, AC input status, capacity, input voltage range #1 (measured in Volts), input voltage range #2 (measured in Volts), input frequency range (measured in Hertz), part number, serial number, and hardwar
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface Enclosure Management Commands, continued CLEAR BAY BOOT [FIRST | ONCE] [ALL | {[ , | - ] }] Clears the setting for the IPL to be passed to the blade at the next reboot. The “FIRST” argument resets the IPL for all subsequent reboots. The “ONCE” argument resets the IPL for the next reboot only.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface Enclosure Management Commands, continued REBOOT BAY {[ , | - ] } {FORCE} {[PXE | HDD | RBSU]} Sends a request to the server blade to perform a graceful shutdown. Allows for optional boot argument The server blade is then powered on.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Function Description Capability Exclusive to the Command Line Interface Enclosure Management Commands, continued SHOW BAY LIST [ALL | ] Displays the assigned to group, remote console user, and server blade name for each bay in a particular group if a group name is specified or all bays if ALL is specified. The command line displays the remote console user.
Command Line Interface Table 4-8: Functionality Exclusive to the Command Line Interface continued Enclosure Management Commands, continued ENABLE NTP Enables automatic time and date updates to Integrated Administrator. Only enclosure administrators may execute this command. REMOVE IPMANAGER Removes the IP address from the list of clients allowed to connect to Integrated Administrator. Only enclosure administrators may execute this command.
5 Setting Up the System This chapter explains the levels of user rights recognized by the Integrated Administrator and provides detailed procedures to configure the management functionalities provided by the Integrated Administrator.
Setting Up the System • Setting up IP Security — Adding IP address — Enabling IP Security — Disabling IP Security • Setting up Automatic Time Configuration (NTP) — Adding primary NTP server — Adding secondary NTP server — Setting the poll interval — Enabling NTP — Disabling NTP • Configuring SNMP support — Entering a community string — Modifying the system location — Modifying the system contact information — Adding trap targets — Removing trap targets For a detailed explanation of the command line c
Setting Up the System User Permissions The group-centered approach of Integrated Administrator to user permissions facilitates the maintenance of user groups and groups of server blade bays. This approach operates according to the following principles: • A server blade bay is assigned exclusively to one group only. • A group can be assigned many server blade bays. • A user can have various permission levels within any number of groups.
Setting Up the System Table 5-1: Permission Levels of the ProLiant BL e-Class Integrated Administrator continued Title Account Type Permissions Description Group administrator User View/Modify Group administrators may manage server blade bay data for groups in which they are administrators. Group administrators may view server blade bay data for groups in which they are members. Group administrators may modify their profile (not their privileges) and view enclosure data.
Setting Up the System 6. Type in the new Administrator password in the Password and Confirm password fields. 7. Click OK. To change the default Administrator password using the CLI, enter: SET USER PASSWORD Administrator IMPORTANT: The user name (Administrator) is case-sensitive. The must be 3-8 characters long and can include all printable characters. Modifying Enclosure and Rack Names To modify the enclosure name or rack name using the Web-based user interface: 1.
Setting Up the System Figure 5-1: Setting the enclosure name and rack name 7. Click Apply. To modify the enclosure name or rack name using the CLI, enter the following commands sequentially: SET ENCLOSURE NAME IMPORTANT: The must be 1-32 characters long and includes all alphanumeric, the dash, and the underscore characters. The default enclosure name is IA-XXXXXXXXXXXX where XXXXXXXXXXXX is replaced with the actual MAC address.
Setting Up the System Modifying the Asset Tag Number To modify the asset tag number using the Web-based user interface: 1. Click the Enclosure tab. 2. Click Enclosure Information in the left panel. 3. Scroll down to the General area. 4. Click the Asset Tag field. 5. Type the asset tag number. Figure 5-2: Setting the asset tag number 6. Click Apply. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System To modify the asset tag number using the CLI, enter: SET ENCLOSURE ASSET {TAG} IMPORTANT: The must be 1-31 characters long and includes alphanumeric, dash, and underscore characters. The default enclosure asset tag is blank. Modifying the Date and Time To modify the date and time settings using the Web-based user interface: NOTE: On a Linux system, this information can only be modified using the CLI. 1. Click the Enclosure tab. 2.
Setting Up the System Figure 5-3: Setting the date and time 7. Click Apply. To modify the date and time settings using the CLI, enter: SET DATE MMDDhhmm{{CC}YY} {TZ} where: • MM: month • DD: day • hh: hour (24-hour time, an integer from 0-23) • mm: minute • CC: century • YY: year • TZ: timezone HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System IMPORTANT: If the time zone is left blank, the current time zone is left in effect. For a list of supported time zones, see Appendix F, “Time Zone Settings.” Setting Up User Accounts IMPORTANT: Only enclosure administrators may perform this task. The ProLiant BL e-Class Integrated Administrator enables you to manage server blade bays and administer users by organizing those server blade bays and users into groups.
Setting Up the System 3. Type the group name and description in the fields. 4. Select bays for the group by selecting the appropriate checkboxes. IMPORTANT: If a server blade bay is gray, that server blade bay is inaccessible because it already belongs to another group. Figure 5-4: Setting a new group’s name, description, and rights to server blade bays HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System 5. To add existing users to this group: a. Select users in the User Names area. Figure 5-5: Choosing an existing user to add to a new group (user highlighted) 5-12 HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System b. Click Add User [View] or Add User [View/Modify]. For more information on permission levels, see the “User Permissions” section in this chapter. Figure 5-6: Giving an existing user View rights to a new group 6. Click Apply. To create a group using the CLI, enter the following commands sequentially: ADD GROUP IMPORTANT: The must be unique to all other group names and user names and is case-sensitive.
Setting Up the System ASSIGN BAY [ALL | {[ , | - ]}] ASSIGN USER {[VIEW | MODIFY]} IMPORTANT: The and are case-sensitive. The “Administrator” account cannot be added to a group. The default setting is View. Adding a User IMPORTANT: Restricted default names of group and user accounts are not case-sensitive. Non-default group and user names are case-sensitive.
Setting Up the System 3. Type the user information in the appropriate field. For information on “Account Type,” see the “User Permissions” section in this chapter. Figure 5-7: Setting a new user’s name, password, rights, and ancillary information NOTE: The Account Type setting determines whether the account holder has management permissions. The optional Full Name and Contact Information fields provide the account holder’s name and a readily accessible means of contact in case of emergency.
Setting Up the System 4. To assign the user to an existing group: a. Select groups in the Group Names area. Figure 5-8: Choosing an existing group for the new user (group highlighted) 5-16 HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System b. Click Add User [View] or Add User [View/Modify]. For more information on permission levels, see the “User Permissions” section in this chapter. Figure 5-9: Giving a new user View rights to an existing group 5. Click Apply. To add a user using the CLI, enter the following commands sequentially: ADD USER {} IMPORTANT: The must be unique to all other user names and group names and is case-sensitive.
Setting Up the System SET USER FULLNAME {} IMPORTANT: The must be 0-20 characters long and can include all alphanumeric characters, the dash, the underscore, and spaces. SET USER CONTACT {} IMPORTANT: The must be 0-20 characters long and can include all alphanumeric characters, the dash, the underscore, and spaces.
Setting Up the System To configure a server blade running Linux to use a serial console: 1. Attach the Diagnostic Adapter to the server blade you wish to configure. NOTE: The Diagnostic Adapter ships with the enclosure. 2 1 Figure 5-10: Attaching the Diagnostic Adapter HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: f-ch5 Setting Up the System.
Setting Up the System 2. Connect a keyboard and monitor to the Diagnostic Adapter and log into the server blade as root.
Setting Up the System 3. If your Linux server blade uses LILO: a. Remove the “message=” file specification from /etc/lilo.conf. IMPORTANT: Step a is necessary because the remote console of the Integrated Administrator is text-based, and the message file may be graphical. b. Add the following line to the ‘linux’ image specification in /etc/lilo.conf: append “console=tty0 console=ttyS0,115200” CAUTION: Be sure the text in step a is indented in the file. c.
Setting Up the System Setting Up AlertMail AlertMail enables users to receive system events by e-mail instead of using SNMP traps. AlertMail is completely independent from SNMP and both can be enabled at the same time. AlertMail uses standard SMTP commands to communicate with an SMTP capable mail server.
Setting Up the System • Power supply status change • Power supply inserted • Power supply removed • Power subsystem redundancy change • Blade inserted • Blade removed • Blade status change • Blade thermal change • Blade fault NOTE: If the enclosure has a switch installed, it can take up to 60 seconds before the system will send out an AlertMail after a system boot up. Events generated within this period of time will be sent out when the switch has come online.
Setting Up the System Example e-mail: ----SAMPLE START---Subject: HP AlertMail-010: (CRITICAL) Power Supply #1: Failed Date: Wed, 23 Apr 2003 15:02:22 +0200 From: Enclosure IA-00508BEBA571 To: user@userdomain X-OS: HP Integrated Administrator X-Priority: 1 Content-Type: text/plain; charset=us-ascii EVENT (26 May 07:09): Power Supply #1 Status has changed to: Failed Enclosure, IA-00508BEBA571, has detected that a power supply in bay 1 has changed from status OK to Failed.
Setting Up the System Table 5-4: IP Security Commands Function Command Add an IP address ADD IPMANAGER Remove an IP address REMOVE IPMANAGER Enable IP Security ENABLE IPSECURITY Disable IP Security DISABLE IPSECURITY Setting Up Automatic Time Configuration (NTP) Automatic time configuration allows the Integrated Administrator to synchronize its date and time with a server supporting the Network Time Protocol (NTP).
Setting Up the System Configuring SNMP Support IMPORTANT: Only enclosure administrators may execute these tasks. Figure 5-12: Setting a community string, trap target destinations, or system location and contact information Entering a Community String To enter a read community or write community string using the Web-based user interface: 1. Click the Enclosure tab. 2. Click SNMP Configuration in the left panel. 3. Click the Read Community or Write Community field.
Setting Up the System 4. Type the string. IMPORTANT: Entering a blank string into the Read Community field sets the Read Community to “public.” Entering a blank string into the Write Community field disables the SNMP set commands. 5. Click Apply. To enter a read community or write community string using the CLI, enter: SET SNMP COMMUNITY [READ | WRITE] The write must be 0-20 characters long and the read must be 1-20 characters long.
Setting Up the System Modifying the System Contact Information To modify the system contact information using the Web-based user interface: 1. Click the Enclosure tab. 2. Click SNMP Configuration in the left panel. 3. Set the cursor in the System Contact field and type the appropriate information. 4. Click Apply.
Setting Up the System Removing Trap Targets To remove a trap target list using the Web-based user interface: 1. Click the Enclosure tab. 2. Click SNMP Configuration in the left panel. 3. Type the list name in the appropriate field of the SNMP area. 4. Click Remove. 5. Click Apply. To add or remove a trap target list using the CLI, enter: REMOVE SNMP TRAPRECEIVER The must be in the form ###.###.###.###, where ### ranges from 0 to 255.
6 Performing Common Administrative Tasks This chapter explains the Integrated Administrator management functionalities: • Managing server blade bays — Opening a remote console session to a server blade — Accessing ROM-Based Setup Utility for a server blade — Reviewing the activity for a server blade — Powering off the server blade CAUTION: Without the server blade health driver, the Integrated Administrator cannot gracefully shutdown a server blade.
Performing Common Administrative Tasks Managing Server Blade Bays Opening a Remote Console Session to a Server Blade IMPORTANT: If a server blade is running the Windows 2000 operating system, only sequences that occur before the loading of the operating system are visible using Remote Console, unless the server blade is running the HP ProLiant Serial Console for Windows 2000 Server service.
Performing Common Administrative Tasks 3. Select the server blade from the blade list. Figure 6-1: Choosing a server blade bay (server blade bay 5 highlighted) 4. Click Remote Console. The Remote Console screen displays. 5. Click Remote Console. This action opens a new window that enables you to connect to the server blade terminal interface. To access the remote console using the CLI, enter: CONNECT BAY IMPORTANT: A server blade can only support one remote console session at a time.
Performing Common Administrative Tasks Accessing the ROM-Based Setup Utility for a Server Blade IMPORTANT: Enclosure administrators and group administrators with access to the bay can select the Remote Console button to open a remote text-based console to the server blade in the bay. To access the ROM-Based Setup Utility (RBSU) for a server blade using the Webbased user interface: 1.
Performing Common Administrative Tasks 9. When prompted to press the F9 key for ROM-Based Setup Utility: a. Press the Esc key. b. Press the 9 key. 10. To exit RBSU: a. Press the Esc key. b. When prompted to press F10, press the Esc key and the 0 key to confirm. 11. To close the remote console session: a. Press the Ctrl-_ keys. b. Press the D key.
Performing Common Administrative Tasks 4. When prompted to press the F9 key for ROM-Based Setup Utility: a. Press the Esc key. b. Press the 9 key. 5. To exit RBSU: a. Press the Esc key. b. When prompted to press F10, press the Esc key and the 0 key to confirm. 6. To close the remote console session: a. Press the Ctrl-_ keys. b. Press the D key.
Performing Common Administrative Tasks Powering Off the Server Blade CAUTION: Without the server blade health driver or an ACPI-compliant operating system, the Integrated Administrator cannot gracefully shutdown a server blade. This condition may result in the permanent loss of critical data. CAUTION: Rebooting or powering off the server blade removes all power from the server blade and ends all open sessions.
Performing Common Administrative Tasks 5. Click Reboot, Power Off or Power Off Immediately. Figure 6-2: Managing server blade power 6. Click Apply. When the server blade power is off, the Power Off button text becomes Power On. To reboot the server blade using the CLI, enter: REBOOT BAY {[ , | - ] } {FORCE} {[PXE | HDD | RBSU]} NOTE: This command sends a request to the server blade in a given bay to perform a graceful shutdown and then reboots the server blade.
Performing Common Administrative Tasks To power off the server blade (immediately or otherwise) using the CLI, enter: POWEROFF BAY {[ , | - ] } {FORCE} IMPORTANT: If the FORCE argument is invoked, the server blade powers down immediately and could lose data or become unstable.
Performing Common Administrative Tasks 5. Click Toggle ON or Toggle OFF depending on the current state of the Unit Identification LED for the server blade.
Performing Common Administrative Tasks Managing the Enclosure Reviewing the Activity of the Enclosure The system log of the Integrated Administrator is a chronology of system activities, such as user logins, enclosure shutdowns, and system failures.
Performing Common Administrative Tasks To view the System Log using the Web-based user interface: 1. Click the Enclosure tab. 2. Click System Log in the left panel. Figure 6-4: Accessing the enclosure’s system log 3. To update the System Log, click Refresh. 4. To clear the System Log, click Clear Log. The Integrated Administrator prompts you to confirm this decision.
Performing Common Administrative Tasks Identifying the Enclosure Using the Unit Identification LED The virtual button for the Unit Identification LED of an enclosure physically changes the state of the Unit Identification LED on the rear panel of the enclosure from Off to On, or vice-versa. The Unit Identification LED illuminates bright blue and is designed to help a technician quickly identify a specific enclosure in the data center.
Performing Common Administrative Tasks To change the state of the Unit Identification LED for the enclosure using the CLI, enter: SET ENCLOSURE UID [ON | OFF] IMPORTANT: Only enclosure administrators may execute this command.
Performing Common Administrative Tasks To obtain the enclosure information using the CLI, enter the following commands as needed: SHOW ENCLOSURE FAN [ | ALL] IMPORTANT: This command displays the status, redundancy, partner, speed, and part number for one or all fans in the enclosure.
Performing Common Administrative Tasks Identifying Problem Components The Integrated Administrator alerts you to problem conditions or failed components in the enclosure, such as: • A fan • A power supply • A server blade • Over-temperature conditions If the enclosure enters a degraded state at any time, the Web-based user interface of the Integrated Administrator alerts the user with icons along the top of the deck panel.
Performing Common Administrative Tasks You can identify the degraded components in the enclosure and their respective part numbers in the following ways: • Opening the enclosure system log • Opening the event list The event list differs from the system log in the following ways: — Any user can view the event list. Only enclosure administrators can access the system log. — The messages in the event list are limited to cautions and critical failures.
Performing Common Administrative Tasks To identify a degraded component using the System Log from the Web-based user interface: 1. Click on the Enclosure tab. 2. Click on System Log in the left panel. Figure 6-8: Viewing the enclosure system log during a fan failure (Fan 1 removed) 3. Go to the appropriate area in the Integrated Administrator for the spare number of the degraded component.
Performing Common Administrative Tasks To identify a degraded component using the event list from the Web-based user interface: 1. Click the Event List tab. Figure 6-9: Viewing the event list during a fan failure 2. Click the degraded item in the event list. 3. Click View Event Details along the bottom of the screen. This action opens the page in the Integrated Administrator that displays information about the degraded component.
Performing Common Administrative Tasks To identify a degraded component using the Caution or Critical icons along the top of the deck panel from the Web-based user interface, click an icon. This action opens the event list. By highlighting an item in the event list and clicking View Event Details, you can access the area within the Integrated Administrator that provides detailed information about that degraded component.
Performing Common Administrative Tasks 2. Enter the appropriate commands: SHOW ENCLOSURE FAN [ | ALL] IMPORTANT: This command displays the status, redundancy, partner, speed, and part number for one or all fans in the enclosure.
Performing Common Administrative Tasks Managing Users IMPORTANT: Only enclosure administrators may perform these tasks. IMPORTANT: Restricted default names of group and user accounts (Administrator, switcha, and switchb) are not case-sensitive. Non-default group and user names are case-sensitive.
Performing Common Administrative Tasks Modifying Group Rights to Server Blade Bays To modify group rights to server blade bays using the Web-based user interface: 1. Click the Administration tab. 2. Click Group List in the left panel. Figure 6-11: Choosing a group from the group list 3. Click on the group whose rights you wish to modify. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: g-ch6 Performing Common Administrative Tasks.
Performing Common Administrative Tasks 4. Click View/Modify Group. Figure 6-12: Accessing the View/Modify Group screen 5. Select the appropriate checkboxes for the available server blade bays that reflects the updated rights you wish to give the group. IMPORTANT: Grayed-out checkboxes are unavailable because they are already assigned to another group. 6. Click Apply.
Performing Common Administrative Tasks To modify rights to server blade bays for an existing group using the CLI, choose from among the following commands: IMPORTANT: Only enclosure administrators may execute these commands. • To expand the number of server blades assigned to a group, enter: ASSIGN BAY [ALL | {[ , | - ]}] IMPORTANT: If a server blade bay is currently assigned to a group, this command reassigns the bay from its current group to the new group.
Performing Common Administrative Tasks 4. Click View/Modify User. Figure 6-13: Accessing the View/Modify User screen 5. Set the account status to Disabled. 6. Click Apply. To disable a user account using the CLI, enter: DISABLE USER IMPORTANT: When this command is executed, the user is immediately logged out of the system and prevented from logging in until the account is enabled. Deleting a User’s Account To delete a user account using the Web-based user interface: 1.
Performing Common Administrative Tasks 3. Select the user account you wish to delete from the user list. Figure 6-14: Accessing the user list 4. Click Remove User. To delete a user account using the CLI, enter: REMOVE USER [ALL | ] IMPORTANT: If ALL is specified, the command deletes all the user accounts except the “Administrator” account. The “Administrator” account cannot be removed. Deleting Group Accounts To delete a group account using the Web-based user interface: 1.
Performing Common Administrative Tasks 3. Select the group from the group list. Figure 6-15: Accessing the group list 4. Click Remove Group. To delete a group account using the CLI, enter: REMOVE GROUP [ALL | ] IMPORTANT: If ALL is specified, the command deletes all the group accounts. 6-28 HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: g-ch6 Performing Common Administrative Tasks.
7 Performing Advanced Functions This chapter provides an explanation of the following advanced tasks you can perform using the Integrated Administrator.
Performing Advanced Functions Replicating the Configuration of the Integrated Administrator IMPORTANT: The Integrated Administrator does not support this task using the Web-based user interface. To set up several enclosures with the same configuration, configure one enclosure (such as add all user accounts, add all groups, and assign bays) and then replicate that configuration on the other enclosures. To replicate the configuration of the Integrated Administrator using the CLI: 1.
Performing Advanced Functions 4. Restore the factory defaults on each of the other enclosures to clear any previous configuration: a. Login as Administrator on an enclosure to which you intend to replicate the configuration. b. Enter: SET FACTORY This command sets the Integrated Administrator back to its factory default settings, although the password of the “Administrator” account does not change. The Integrated Administrator is restarted after all the changes are implemented.
Performing Advanced Functions Administering Security Certificates IMPORTANT: The Integrated Administrator does not support these tasks using the Web-based user interface. Creating a Certificate Request To create a security certificate using the CLI, enter: GENERATE CERTIFICATE REQUEST This command generates a PKCS#10 certificate request. This certificate request can be sent to your certification authority (CA) to obtain a PKCS#7 certificate file to use below.
Performing Advanced Functions If your ftp server does not support anonymous connections, you can specify a username and password by replacing the host part in the previous format: username:password@host Key-Based SSH Authentication Users may install their own public SSH keys for password-less logins to the Integrated Administrators. Only enclosure administrators can use key-based authentication. The CLI features four commands to install and manage the authorized SSH keys.
Performing Advanced Functions To download and install one or more SSH keys, enter: DOWNLOAD SSHKEY This command will download and install a file containing one or more SSH keys which are authorized to log into the Integrated Administrator. The new file will replace any existing keys. Supported protocols are http, ftp and tftp.
Performing Advanced Functions Configuring Server Blade Boot Order Enclosure and group administrators may change the boot order, sometimes referred to as Initial Program Load (IPL), of their server blades by using the CLI of the Integrated Administrator. The change can be made permanently or only for the next reboot. Several commands are available in the CLI to control the blades in this manner. This feature requires version 1.
Performing Advanced Functions The POWERON BAY and REBOOT BAY commands have been extended to allow an argument which sets server blade boot order for that boot only. These settings are the same as the SET BAY BOOT ONCE command. To determine if any boot order changes are pending for a specific blade, use the SHOW BAY INFO command. The “Pending Boot Order:” status line will show any pending changes to the boot order, either one-time or permanent.
Performing Advanced Functions 3. Click Power Off. 4. Click Apply. To power off the enclosure using the CLI, enter: POWEROFF ENCLOSURE This command attempts to perform a graceful shutdown of the enclosure by powering off each server blade and then powering off the enclosure. After 5 minutes, the command powers down all components of the system immediately if they are not already powered off.
Performing Advanced Functions Disabling Network Protocols To modify the supported communications protocols of the enclosure using the Web-based user interface: 1. Click the Enclosure tab. 2. Click Network Configuration in the left panel. Figure 7-2: Accessing the Network Configuration screen 3. Select the appropriate radio buttons in the Protocols area. 4. Click Apply.
Performing Advanced Functions • To disable automatic time updates, enter: DISABLE NTP IMPORTANT: Disabling http/https causes the users to lose access to the Web-based user interface. • To disable SNMP communication, enter: DISABLE SNMP • To disable Secure Shell communication, enter: DISABLE SECURESH IMPORTANT: Disabling Secure Shell causes the users to lose access to the Web-based user interface.
Performing Advanced Functions Refer to the documentation associated with the firmware upgrade for detailed information. Recovering a Lost Administrator Password To recover a lost Administrator password: 1. Be sure the local client device is properly configured for local access to the Integrated Administrator. See the “Requirements for Local Client Devices” section in Chapter 2, “Getting Started.” 2.
Performing Advanced Functions 3. Open a terminal emulation application. 4. Press and hold the enclosure Unit Identification button (1) and press the Integrated Administrator Reset button (2) simultaneously on the rear panel of the server to place the enclosure in Lost Password/Flash Disaster Recovery mode. 1 2 Figure 7-4: Enclosure Unit Identification button and the Integrated Administrator Reset button 5. When the serial console prompt appears, press the L key.
Performing Advanced Functions IMPORTANT: The filename of the ROM image of the Integrated Administrator can be any valid ASCII filename. The ROM image of the Integrated Administrator can be any valid image that supports the “update image" facility in the operating system. The Integrated Administrator will automatically enter Flash Recovery mode when a corrupted image is detected. Flash Recovery mode can also be manually initiated. IMPORTANT: No timeout exists for obtaining a DHCP address.
Performing Advanced Functions You can manually place the Integrated Administrator in Flash Recovery mode: 1. Connect a local client device to the Integrated Administrator (serial) console connector using the null-modem serial cable (provided with the enclosure). See the “Requirements for Local Client Devices” section in Chapter 2, “Getting Started.
Performing Advanced Functions 2. Press and hold the enclosure Unit Identification button (1) and press the Integrated Administrator Reset button (2) simultaneously on the rear panel of the server to place the enclosure in Lost Password/Flash Disaster Recovery mode.
Performing Advanced Functions 3. When the serial console prompt appears, press the F key. IMPORTANT: This command is case-insensitive. Pressing the L key launches Lost Password recovery mode. Pressing any other key exits Lost Password/Flash Disaster Recovery mode and reboots the system. This command boots the system in Flash Disaster Recovery mode, prints a message, and resets the enclosure. Upon entering Flash Disaster Recovery mode, the Integrated Administrator attempts to acquire a DHCP address.
A Command Line Conventions The following sections provide commands for the CLI using the convention described in Table A-1: Table A-1: Command Line Conventions Symbol Description Denotes input to be keyed in UPPER CASE Denotes input to be keyed in as shown [] Denotes choices to be made where a choice is mandatory {} Denotes choices to be made where a choice is optional | “” Separates input options Used to enclose arguments that contain spaces For example, the following command requ
B Error Messages The messages provided in this appendix are divided into the following categories: • Warning messages • Error messages Warning Messages This section provides a comprehensive list of warning messages specific to the major components of the Integrated Administrator. These warning messages advise you that you have implemented a configuration change or prompt you to confirm whether you wish to proceed with your requested action.
Error Messages Enclosure Warning Messages Table B-1: Enclosure Warning Messages Warning Message Cause Are you sure you want to disable the Web protocol? Disabling this protocol will prevent access to the Web-based user interface until a terminal session re-enables the Web protocol.
Error Messages Server Blade Bay Warning Messages Table B-2: Server Blade Bay Warning Messages Warning Message Cause This server blade has been removed from the enclosure. The server blade that is being viewed has been removed from the enclosure. This server blade has been powered off. All open sessions will be closed. The current server blade has been powered off.
Error Messages Error Messages This section provides a comprehensive list of error messages specific to the major components of the Integrated Administrator. These error messages advise you that an error has occurred during the normal operation of the Integrated Administrator. Enclosure Error Messages Table B-4: Enclosure Error Messages Error Message Cause Valid Input th The maximum number (8) of trap destinations has been reached.
Error Messages Administration Error Messages Table B-6: Administration Error Messages Error Message Cause Valid Input The user name field is empty. Please enter a user name. Attempting to create a user with a blank user name 1-13 characters including alphanumeric, dash, and underscore characters. The user name must begin with a letter. This user name already exists. Please select a different user name.
Error Messages Table B-6: Administration Error Messages continued Error Message Cause Valid Input The group name is blank. Please enter a valid name. Attempting to create a group with a blank group name 1-13 characters including alphanumeric, dash, and underscore characters The group name must begin with a letter. The maximum number (20) of groups exists on the system. Attempting to create a 21st group N/A The Password fields are empty. Please enter a value in each password field.
Error Messages Table B-6: Administration Error Messages continued Error Message Cause Valid Input Please set at least the Primary NTP server before enabling NTP. Attempting to enable the NTP server before enabling the primary NTP server set. N/A is already set as secondary NTP server. Attempting to set the primary NTP server to when the is already set as secondary. N/A is already set as primary NTP server.
C Troubleshooting This appendix provides troubleshooting information for the Integrated Administrator that ships as part of the ProLiant BL e-Class system. Use it to find details about solving performance problems that may arise when viewing or managing enclosure, server blade, or user information using the Integrated Administrator. For information on troubleshooting hardware for the ProLiant BL e-Class system, refer to the HP ProLiant BL e-Class System Setup and Installation Guide.
Troubleshooting Table C-1: Integrated Administrator Troubleshooting Problems Possible Solution My Web browser flickers when I view the Integrated Administrator applet. Be sure the client browser has at least 16-bit color depth. My Web browser is not supported by the Integrated Administrator. Be sure to use a supported Web browser. For the most up-todate information on supported Web browsers, please view the customer advisories located at www.compaq.
Troubleshooting Table C-1: Integrated Administrator Troubleshooting continued Problems Possible Solution I just got logged out of the GUI. Why? What should I do? Your rights may have changed. If so, log in again to use your new rights. If the problem continues, contact the enclosure administrator. When I ran “upload config,” garbage printed to the screen and then a statement printed saying the command completed successfully. No error occurred in this command. Everything ran as expected.
D Event Details The Integrated Administrator provides real-time event notifications for an enclosure according to two categories: caution and critical.
Event Details The following table provides a comprehensive list of event messages provided by the Integrated Administrator in a format that reflects the display of the Integrated Administrator: Table D-2: Event Details Severity D-2 Source Date Time Event Details Enclosure
E Factory Default Settings This appendix provides the factory default settings for the following components of the ProLiant BL e-Class Integrated Administrator: • Enclosure • Users • Groups • Network • Protocol HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: m-appe Factory Default Settings.
Factory Default Settings Enclosure Table E-1 provides the default values in the Integrated Administrator for fields related to the server blade enclosure.
Factory Default Settings Groups No default groups are in the Integrated Administrator. Network The Integrated Administrator ships with the following default values assigned: Table E-2: Integrated Administrator's Default Network Values Field Default Value DHCP Enabled Dynamic DNS Enabled Protocol Table E-3 provides the default values in the Integrated Administrator for fields related to network interface protocols.
Factory Default Settings Table E-3: Default Protocol Values of Integrated Administrator continued E-4 Field Default Value IP Security Disabled AlertMail Disabled HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: m-appe Factory Default Settings.
F Time Zone Settings This appendix provides a comprehensive list of time zones supported by the ProLiant BL e-Class Integrated Administrator. These time zones are organized into the following categories: • Universal • Africa • Asia • Europe • Oceania • Polar • The Americas HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: n-appf Time Zone Settings.
Time Zone Settings Universal Table F-1 provides the Universal time zone settings supported by the Integrated Administrator. CAUTION: For the Integrated Administrator to recognize GMT time zones, the “Etc:” string must precede them.
Time Zone Settings Africa Table F-2 provides the African time zone settings supported by the Integrated Administrator.
Time Zone Settings Asia Table F-3 provides the Asian time zone settings supported by the Integrated Administrator.
Time Zone Settings Table F-3: Asian Time Zone Settings Supported by the Integrated Administrator continued Asia:Tel_Aviv Asia:Vladivostok Mideast:Riyadh88 Asia:Thimbu Asia:Yakutsk Mideast:Riyadh89 Asia:Thimphu Asia:Yekaterinburg PRC Asia:Tokyo Asia:Yerevan ROC Asia:Ujung_Pandang Hongkong ROK Asia:Ulaanbaatar Iran Singapore Asia:Ulan_Bator Israel Turkey Asia:Urumqi Japan Asia:Vientiane Mideast:Riyadh87 HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writ
Time Zone Settings Europe Table F-4 provides the European time zone settings supported by the Integrated Administrator.
Time Zone Settings Oceania Table F-5 provides the Oceanic time zone settings supported by the Integrated Administrator.
Time Zone Settings Table F-5: Oceanic Time Zone Settings Supported by the Integrated Administrator continued Pacific:Marquesas Pacific:Pitcairn Pacific:Tongatapu Pacific:Midway Pacific:Ponape Pacific:Truk Pacific:Nauru Pacific:Port_Moresby Pacific:Wake Pacific:Niue Pacific:Rarotonga Pacific:Wallis Pacific:Norfolk Pacific:Saipan Pacific:Yap Pacific:Noumea Pacific:Samoa US:Hawaii Pacific:Pago_Pago Pacific:Tahiti US:Samoa Pacific:Palau Pacific:Tarawa F-8 HP ProLiant BL e-Class Integrat
Time Zone Settings Polar Table F-6 provides the Polar time zone settings supported by the Integrated Administrator.
Time Zone Settings The Americas Table F-7 provides the American time zone settings supported by the Integrated Administrator.
Time Zone Settings Table F-7: American Time Zone Settings Supported by the Integrated Administrator continued America:Chicago America:Guadeloupe America:Los_Angeles America:Louisville America:Rainy_River Brazil:DeNoronha America:Maceio America:Rankin_Inlet Brazil:East America:Managua America:Recife Canada:Central America:Manaus America:Regina Canada:Eastern America:Martinique America:Rio_Branco Canada:East-Saskatchewan America:Mazatlan America:Rosario Canada:Mountain America:Mendoza A
Time Zone Settings Table F-7: American Time Zone Settings Supported by the Integrated Administrator continued America:Panama America:Tijuana US:Central America:Pangnirtung America:Tortola US:Eastern America:Paramaribo America:Vancouver US:East-Indiana America:Phoenix America:Virgin US:Indiana-Starke America:Port_of_Spain America:Whitehorse US:Michigan America:Port-au-Prince America:Winnipeg US:Mountain America:Porto_Acre America:Yakutat US:Pacific America:Porto_Velho America:Yellowkni
G Open Source Availability The Integrated Administrator is based on embedded Linux and contains numerous Open Source components. In compliance with Open Source licensing, HP has made the source code of all Open Source components used available at: opensource.hp.com To locate the Integrated Administrator project, consult the list of all projects. HP ProLiant BL e-Class Integrated Administrator User Guide HP CONFIDENTIAL Writer: Amy Clute File Name: o-appg Open Source Availability.
Index 1 128-bit encryption 1-3 A accessing command line interface 4-2 Integrated Administrator, locally 4-2 Integrated Administrator, remotely 3-2, 4-2 server blade RBSU 6-4 ADD ADD GROUP command 4-7 ADD SNMP TRAPRECEIVER command 4-12 ADD USER command 4-7 IPMANAGER command 4-35 Add Group screen See also Administration tab Apply button 3-40 bay assignment area 3-41 Cancel button 3-40 group information area 3-41 group membership area 3-41 Add User screen See also Administration tab Apply button 3-37 Cancel
Index events 5-22 sender domain 5-22 setting up 5-22 severity 5-23 alerts security 2-7 SNMP 1-2 American time zone F-10 Asian time zone F-4 asset tag number, modifying 5-7 ASSIGN ASSIGN ADMINISTRATOR RIGHTS command 4-8, 4-11 ASSIGN BAY command 4-8 ASSIGN USER command 4-8 attaching the dianostic adpater 5-19 authorized reseller xiii Automatic Server Recovery-2 1-6 automatic time configuration disable 5-25 disable secondary NTP server 5-25 enable 5-25 NTP poll interval 5-25 primary NTP server, set 5-25 secon
Index CLEAR BAY BOOT [FIRST | ONCE] command 4-20, 4-33 CLEAR SSHKEY command 4-4, 4-27 command line interface accessing 4-2 conventions A-1 enclosure management commands 4-16 enclosure network configuration commands 4-12 functionality 4-27 general commands 4-3 general management commands 4-4 guidelines A-1 server bay managment commands 4-20 user account commands 4-7 community string, entering 5-26 components for configuring the diagnostic adapter 5-20 CONFIG, DOWNLOAD command 4-13, 4-31 CONFIG, SHOW command
Index ENABLE SNMP command 4-13 ENABLE TELNET command 4-13 ENABLE USER command 4-8 ENABLE WEB command 4-13 IPSECURITY command 4-35 NTP command 4-36 enabling remote console sessions to server blades 5-18 enclosure customizing settings 5-4 error messages B-4 event messages 4-25 factory default settings E-2 generating a summary 6-14 identifying by using the unit identification LED 6-13 identifying problem components 6-16 managing 6-11 modifying the name, 5-5 powering off 7-8 reviewing activity 6-11 system log
Index F factory default settings E-1 enclosure E-2 groups E-3 network E-3 protocol E-3 users E-2 FACTORY, SET command 4-5, 4-29 fan failure integrated administrator Web-based user interface 6-16 system log 6-18 features Diagnostics Utility 1-6 Enclosure Self Recovery 1-6 Headless server operation 1-5 Health and Wellness Driver 1-7 HP Management Agents 1-7 Integrated Management Log 1-7 Online ROM flash 1-7 Rapid Deployment Pack (Option) 1-6 Redundant ROM support 1-5 ROM-based Setup Utility 1-5 secure passwo
Index description 1-1 disabling network protocols 7-10 error messages B-1 features 1-2 features, administration 1-3 features, AlertMail 1-2 features, automatic network configuration 1-4 features, automatic time configuration 1-4 features, dedicated LAN network connectivity 1-2 features, e-mail alerts 1-2 features, event notification 1-5 features, hyperlinks 1-4 features, remote access and control 1-2 features, security 1-3 features, SNMP 1-2 features, status information 1-5 permission levels 5-3 remote acc
Index date 5-8 enclosure name 5-5 group rights to server blade bays 6-23 new group description 5-11 new group name 5-11 new group rights to server blade bays 5-11 rack name 5-5 system contact information 5-28 system location 5-27 time 5-8 user's rights to server blade bays 6-22 N native graphical remote console 1-3 NETWORK SHOW NETWORK command 4-15 Network Configuration screen See also Enclosure tab Apply button 3-13 Cancel button 3-13 information area 3-14 Network and Information and Protocols area 3-14
Index Redundant ROM support 1-5 remote access 1-2 Integrated Administrator 3-2, 4-2 Remote Console screen See also Bays tab Remote Console button 3-28 remote console session, opening to a server blade 6-2 Remote Console, hardware-based 1-3 remote reboot 1-2, 1-3 remote ROM flash 1-7 REMOVE IPMANAGER command 4-36 REMOVE GROUP command 4-8 REMOVE SNMP TRAPRECEIVER command 4-13 REMOVE USER command 4-9 removing trap targets 5-29 replicating the Integrated Administrator configuration 7-2 reset and failure sequen
Index SET ENCLOSURE NAME command 4-17 SET ENCLOSURE UID command 4-17 SET FACTORY command 4-5, 4-29 SET GATEWAY command 4-14 SET GROUP DESCRIPTION command 4-9 SET IPCONFIG command 4-14 SET PASSWORD command 4-9 SET RACK NAME command 4-17 SET SCRIPT MODE command 4-5, 4-30 SET SNMP COMMUNITY command 4-14 SET SNMP CONTACT command 4-14 SET SNMP LOCATION command 4-15 SET USER CONTACT command 4-10 SET USER FULLNAME command 4-10 SET USER PASSWORD command 4-10 SET BAY BOOT FIRST command 4-22, 4-34 SET BAY BOOT ONCE
Index Apply button 3-16 Cancel button 3-16 system information area 3-17 SNMP support, configuring 5-26 SSL (Secure Socket Layer) 1-3 startup and shutdown sequence playback 1-2 status information 1-5 symbols in text xi on equipment ix SYSLOG BAY, SHOW command 4-35 SYSLOG ENCLOSURE, CLEAR command 4-16 system contact information, modifying 5-28 system features 1-1 system location, modifying 5-27 System Log screen 3-21.
Index permissions 5-3 setting up accounts 5-10 utilities Diagnostics Utility 1-6 Enclosure Self Recovery-2 1-6 Insight Manager 7 1-6 ROM-Based Setup Utility 1-5 V View/Modify Group screen See also Administration tab View/Modify User screen See also Administration tab virtual buttons 7-8 Virtual Buttons screen See also Bays tab Apply button 3-31 enclosure unit identification area 3-19 Power Off button 3-31 Power Off Enclosure button 3-20 Power Off Immediately button 3-31 Reboot button 3-31 Restart Integrat
