HP ProLiant BL30p Server Blade Setup and Installation Guide May 2004 (First Edition) Part Number 354555-001
© Copyright 2004 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Contents About This Guide Audience Assumptions..................................................................................................... vii Important Safety Information ........................................................................................... vii Symbols on Equipment .................................................................................................... vii Rack Stability .............................................................................................
Contents Chapter 3 Server Blade Setup Accessing Internal Server Blade Components.................................................................3-1 Removing a Server Blade Blank......................................................................................3-2 Installing a Blade Sleeve..................................................................................................3-3 Installing a ProLiant BL30p Server Blade.......................................................................
Contents Deployment Methods.............................................................................................. 5-26 Chapter 6 Connecting Local I/O Devices Using the Local I/O Cable............................................................................................... 6-1 Connecting to a Server Blade through iLO ..................................................................... 6-1 Connecting Directly to a Server Blade using Video and USB Devices....................
Contents Appendix D Electrostatic Discharge Preventing Electrostatic Damage.................................................................................... D-1 Grounding Methods ........................................................................................................
About This Guide This guide provides step-by-step instructions for installation and reference information for operation, troubleshooting, and future upgrades for the HP ProLiant BL30p server blade. Audience Assumptions This guide is for the person who installs, administers, and troubleshoots servers. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
About This Guide This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel. This symbol indicates the presence of electric shock hazards. The area contains no user or field serviceable parts. Do not open for any reason.
About This Guide Rack Stability WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling jacks are extended to the floor. • The full weight of the rack rests on the leveling jacks. • The stabilizing feet are attached to the rack if it is a single-rack installation. • The racks are coupled together in multiple-rack installations. • Only one component is extended at a time.
About This Guide Related Documents For additional information on the topics covered in this guide, refer to the following documentation: • HP ProLiant BL System Best Practices Guide • HP ProLiant BL System Common Procedures Guide • HP ProLiant BL p-Class System Hardware Installation and Configuration Poster • White paper: HP ProLiant BL p-Class System Overview and Planning • HP ROM-Based Setup and Utility User Guide • HP Integrated Lights-Out User Guide • HP ProLiant BL p-Class System Maintena
About This Guide Be sure to have the following information available before you call HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number • Applicable error messages • Add-on boards or hardware • Third-party hardware or software • Operating system type and revision level HP Website The HP website has information on this product as well as the latest drivers and flash ROM images. You can access the HP website at www.hp.com.
1 Server Blade Component Identification Server Blade Components and Connectors Use Figure 1-1 and Table 1-1 to identify the server blade components and connectors.
Server Blade Component Identification Figure 1-1: Server blade components and connectors 1-2 HP ProLiant BL30p Server Blade Setup and Installation Guide
Server Blade Component Identification Table 1-1: Server Blade Components and Connectors Item Description 1 Fan assembly connectors (2) 2 System Maintenance Switch (SW1) 3 Processor socket 2 4 Adapter card connectors (2) 5 Battery 6 Power converter module 7 DIMM slots (2) (slot 1 populated) 8 Processor socket 1 (populated) 9 Hard drive cable connector 10 Fan assembly 11 Drive cage assembly HP ProLiant BL30p Server Blade Setup and Installation Guide 1-3
Server Blade Component Identification Front Panel LEDs, Button, and Port Six LEDs on the front of the server blade indicate server status. Use Figure 1-2 and Table 1-2 to identify LED locations and functions.
Server Blade Component Identification Table 1-2: ProLiant BL30p Server Blade Front Panel LEDs, Button, and Port continued Item LED/Button Description Status 3 NIC 1 LED* Green = Linked to network 4 NIC 2 LED* Green flashing = Network activity Off = No activity 5 6 Hard Drive Activity LED Green/Flashing = Activity Power LED/button Green = On Off = No activity Amber = Standby (power available) Off = Unit off 7 I/O port** - *Actual NIC numeration depends on several factors, including the op
Server Blade Component Identification Table 1-3: System Maintenance Switch Settings Position Description On/Off Function Default Setting 1* ILO Security Override Off = iLO Security is enabled. OFF On = Overrides iLO security function. 2 Configuration Lock Off = System configuration can be modified. OFF On = System configuration is locked and cannot be modified. 3 Reserved — OFF 4 Reserved — OFF 5* Password Disable Off = Power-on password is normal.
Server Blade Component Identification Local I/O Cable Connectors Use Figure 1-3 and Table 1-4 to identify the local I/O cable connectors. Figure 1-3: Local I/O cable connectors Table 1-4: Local I/O Cable Connectors Item Connector Name Connector Description 1 Server blade connector Attaches to the I/O port on the front of the server blade. 2 Video connector Provides video capability. 3 USB connector 1 Provides USB connection enabling direct connection to the server blade.
Server Blade Component Identification Table 1-4: Local I/O Cable Connectors continued Item 1-8 Connector Name Connector Description 5 Serial connector Requires a null modem serial cable and enables trained personnel to perform advanced diagnostic procedures. 6 iLO RJ-45 (10/100 Ethernet) connector Provides an Ethernet connector through which you can access the server blade iLO interface from a client device.
2 Server Blade Operations Powering Up the Server Blade By default, server blades are set to power up automatically when installed in a server blade enclosure. If you changed this setting, use one of the following methods to power up the server blade: CAUTION: Be sure that the ProLiant BL30p server blade is installed in a server blade enclosure with enhanced backplane components.
Server Blade Operations • Virtual power button features through the iLO remote console — A momentary power-up selection — A hold power-up selection For more information about iLO, refer to Chapter 5, “Server Blade Configuration and Utilities.” Powering Down the Server Blade The ProLiant BL30p server blade can be powered down in either of the following ways: — Use the virtual power button feature in the iLO remote console to power down the server blade.
3 Server Blade Setup Accessing Internal Server Blade Components 1. Identify the proper server blade in the server blade enclosure. 2. Back up all server blade data. 3. Be sure that the server blade has the most recent ROM version. For the most recent ROM, refer to www.hp.com/support. 4. Remove power from the server blade. Refer to Chapter 2, “Server Blade Operations.” CAUTION: After you press the release button, the server blade is unlocked from the server blade enclosure.
Server Blade Setup Removing a Server Blade Blank Two sizes of blanks exist for the HP ProLiant BL p-Class system. A 6U blank is installed in the server blade enclosure in place of a 6U server blade or blade sleeve. A 3U server blade blank is installed in the blade sleeve in place of a 3U server blade. CAUTION: Always populate the server blade enclosure bays and blade sleeves with either a server blade or server blade blank. Unpopulated bays and blade sleeves can lead to improper cooling and thermal damage.
Server Blade Setup Figure 3-2: Removing a 3U server blade blank NOTE: Store the ProLiant BL30p server blade blank for future use. Installing a Blade Sleeve CAUTION: Be sure that the ProLiant BL30p server blade is installed in a server blade enclosure with enhanced backplane components. Installing a ProLiant BL30p server blade in a server blade enclosure without enhanced backplane components can damage the power subsystem. 1. Remove the server blade blank. Refer to “Removing a Server Blade Blank.” 2.
Server Blade Setup 3. Slide the blade sleeve fully into the bay until it clicks into place. Figure 3-3: Installing a blade sleeve Installing a ProLiant BL30p Server Blade CAUTION: Be sure that the ProLiant BL30p server blade is installed in a server blade enclosure with enhanced backplane components. Installing a ProLiant BL30p server blade in a server blade enclosure without enhanced backplane components can damage the power subsystem.
Server Blade Setup 2. Close the ejector lever (2). CAUTION: Be sure that the ProLiant BL30p server blade is installed in a server blade enclosure with enhanced backplane components. Installing a ProLiant BL30p server blade in a server blade enclosure without enhanced backplane components can damage the power subsystem.
Server Blade Setup Removing a ProLiant BL30p Server Blade WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. CAUTION: Electrostatic discharge can damage electronic components. Properly ground yourself before beginning any installation procedure. Refer to Appendix D, “Electrostatic Discharge,” for more information. 1. Press the release button (1). 2. Open the release lever (2). 3.
4 Hardware Options Installation Processor Option The ProLiant BL30p server blade ships with one or two Intel Xeon™ processors. WARNING: This documentation assumes that the server blade is in a rack and not receiving power from a diagnostic station. If using a diagnostic station, be sure to disconnect the server blade from the diagnostic station before installing a processor. WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them.
Hardware Options Installation Removing a Processor Blank Figure 4-1: Removing a processor blank Replacing a Processor and Heatsink For information on accessing internal server blade components, refer to Chapter 3, “Server Blade Setup.” IMPORTANT: The heatsink is not reusable and must be discarded if removed from the processor after application.
Hardware Options Installation Figure 4-2: Removing the heatsink Figure 4-3: Removing the processor HP ProLiant BL30p Server Blade Setup and Installation Guide 4-3
Hardware Options Installation Installing a Processor and Heatsink CAUTION: If installing only one processor in the server blade, be sure to install a processor blank in processor socket 2. CAUTION: Handle the processor with care. Do not bend or damage the pins beneath the processor. IMPORTANT: The processor and heatsink are designed to fit one way into the socket. Align the arrow on the processor with the arrow on the processor socket.
Hardware Options Installation Figure 4-5: Removing the thermal interface media cover CAUTION: After the thermal interface media cover is removed, do not touch the thermal interface media. IMPORTANT: The heatsink is not reusable and must be discarded if removed from the processor after application.
Hardware Options Installation CAUTION: If installing only one processor in the server blade, be sure to install a processor blank in processor socket 2. Hard Drives Install up to two hard drives in the drive cage assembly included with HP ProLiant BL30p server blades. The primary drive is located in the bottom bay of the hard drive cage and the secondary drive is located in the top bay of the hard drive cage. IMPORTANT: Always populate hard drive bays starting with the primary drive (bottom).
Hardware Options Installation Installing Hard Drives 1. Disconnect the hard drive cable from the system board by pulling the tab on the hard drive cable straight up and away from the connector (1). 2. Loosen the drive cage assembly thumbscrew (2). 3. Rotate the drive cage assembly up and away from the server blade (3). NOTE: If a hard drive is already installed in the drive cage assembly, disconnect the hard drive cable from the hard drive.
Hardware Options Installation 4. Loosen the cover plate thumbscrew (1). 5. Slide the cover plate until the cover plate disengages and remove it from the drive cage assembly (2). 6. Lift the center plate out of the main cage (3).
Hardware Options Installation CAUTION: The hard drive must be installed as described in this document. If installed incorrectly, the hard drive can be damaged. 7. With the main cage oriented as in the Figure 4-9, align the hard drive and install into the main cage (1). Figure 4-9: Aligning and installing the hard drive into the main drive cage NOTE: Be sure that the jumper on the hard drive is set to Cable Select (CS) so that the drive device ID is determined by the hard drive cable.
Hardware Options Installation 8. Install the center plate in the main cage (1). NOTE: Be sure the center plate is oriented as in the following figure. The pins must be pointed down when being installed into the main cage. 9. Align the cover plate and slide into place on the main cage so that all four latches lock into place (2). 10. Tighten the cover plate thumbscrew (3).
Hardware Options Installation IMPORTANT: Be sure to connect the hard drive in the bottom (primary) bay to the bottom (primary) connector on the hard drive cable and connect the hard drive in the top (secondary) bay to the top (secondary) connector on the hard drive cable. 11. Connect the hard drive cable to each hard drive installed in the drive cage assembly (1). 12. Align the tabs on the drive cage assembly with the spaces on the server blade (2) and rotate down into place in the server blade (3). 13.
Hardware Options Installation Interleaving and Non-Interleaving Memory Configuration This server supports both interleaving and non-interleaving memory configurations. Interleaving memory increases bandwidth by allowing simultaneous access to more than one block of data (for example, overlapping Read-Writes). This is accomplished by dividing the system memory in an exact pair of DIMMs and Writing-Reading blocks of data to/from both simultaneously.
Hardware Options Installation DIMM Installation Guidelines Install only PC2100 registered DDR, 3.3-V, 72-bit wide, ECC DIMMs in the server blade. For interleaving memory functionality, install memory in identical pairs. NOTE: The server blade ships with one DIMM installed in DIMM slot 1. HP recommends that you install a second identical DIMM to achieve maximum performance. CAUTION: Use only HP DIMMs. DIMMs from other sources are known to adversely affect data integrity.
Hardware Options Installation 4. Insert the DIMM into the DIMM slot (1). 5. Press down firmly. When the DIMM seats fully in the slot, the latches close (2). Figure 4-12: Installing a DIMM 6. Repeat steps 2 through 5 to install the second DIMM. Dual Port Fibre Channel Adapter An optional Dual Port Fibre Channel adapter (FC adapter) enables fibre channel (FC) support for SAN connection when used in conjunction with either the RJ-45 Patch Panel 2 or the GbE2 Interconnect Switch.
Hardware Options Installation With the BL30p blade and FC adapter, FC port aggregation is required to accommodate the increased number of server FC HBA ports and maintain compatibility with the available enclosure backplane signals and interconnect ports. The BL30p blade sleeve aggregates the four paths from two BL30p blades into two physical paths. Up to sixteen physical FC ports connect from the Patch Panel 2 or GbE2 interconnect switch directly to the customer external FC SAN switch.
5 Server Blade Configuration and Utilities This chapter contains information about server blade deployment methods, hardware configuration, and the software to accomplish these tasks.
Server Blade Configuration and Utilities HP also offers the following software components: • Health and Wellness Driver and IML Viewer • iLO Advanced Management Interface Driver • Rack Infrastructure Interface Service • Management Agents For Microsoft® Windows® operating system users, these items are included in the ProLiant Support Pack for Microsoft Windows, available from the ProLiant BL p-Class system product page h18002.www1.hp.com/support/files/server/us/index.
Server Blade Configuration and Utilities Using a supported web browser, you can: • Remotely access the console of the host server blade, including all text mode and graphics mode screens with full keyboard and mouse controls. • Remotely power up, power down, or reboot the host server blade. • Remotely boot a host server blade to a virtual diskette image to perform a ROM upgrade or to install an operating system. • Send alerts from iLO Advanced regardless of the state of the host server blade.
Server Blade Configuration and Utilities • Through the server blade rear panel connectors (out of the rack, with the diagnostic station): This method enables you to configure a server blade out of the rack by powering the server blade with the diagnostic station and connecting to an existing network through a hub. The IP address is assigned by a DHCP server on a network. iLO ROM-Based Setup Utility The iLO ROM-Based Setup Utility (iLO RBSU) is the recommended method to configure and set up iLO.
Server Blade Configuration and Utilities 3. Enter a valid iLO user ID and password with the appropriate iLO privileges (Administer User Accounts, Configure iLO Settings). NOTE: Use the arrow keys to highlight selections. 4. Select Network, DNS/DHCP, press the Enter key, and then select DHCP Enable. Press the spacebar to turn off DHCP. Be sure that DHCP Enable is set to Off and save the changes. 5.
Server Blade Configuration and Utilities 5. Press the Enter key. 6. Press the Esc key to exit the current menu or press the F10 key to exit RBSU. 7. Restart the server blade. When the server blade boots, the system identifies whether the current ROM bank is corrupt. If a corrupt ROM is detected, the system boots from the backup ROM and alerts you through POST or IML that the ROM bank is corrupt.
Server Blade Configuration and Utilities ROMPaq Utility Flash ROM enables you to upgrade the firmware (BIOS) with system or option ROMPaq utilities. To upgrade the BIOS: 1. Download the latest ROMPaq. h18002.www1.hp.com/support/files/server/us/index.html 2. Follow the instructions and create a bootable diskette. IMPORTANT: You can use the iLO Virtual Media applet to create the image file. Refer to the “Integrated Lights-Out Advanced Management” section in this chapter. If you use this method, omit step 3.
Server Blade Configuration and Utilities To navigate RBSU, use the following keys: • To access RBSU, use the iLO Remote Console and press the F9 key when prompted during power up. • To navigate the menu system, use the arrow keys. • To make selections, press the Enter key. RBSU automatically saves settings when you press the Enter key. The utility does not prompt you for confirmation of settings before you exit the utility.
Server Blade Configuration and Utilities Table 5-1: RBSU Default Settings continued Menu/Option Default Setting Server Passwords Set Power-On Password Disabled Set Admin Password Disabled Advanced Options MPS Table Mode AutoSet Table POST Speed Up Enabled POST F1 Prompt Enabled ROM Selection Use Current ROM Erase Non-Volatile Memory N/A Erase Non-Volatile Memory/Boot Disk N/A Set CPU 1 Corrected N/A Set CPU 2 Corrected N/A Wake-on LAN Enabled NMI Debug Button Enabled Processor Hyp
Server Blade Configuration and Utilities Important Considerations • Works with the 0.90 version of software RAID included in Red Hat Enterprise Linux 3.0, Red Hat Enterprise Linux 2.1, and United Linux 1.0. • Version 1.00 of software RAID included in the latest 2.6 kernels is not supported. • When used with Red Hat Linux, BIOS Enhanced RAID requires selection of the LILO boot loader during installation since GRUB doesn’t fully support software RAID boot devices.
Server Blade Configuration and Utilities Network-Based PXE Deployment Preboot eXecution Environment (PXE) is a component of the Intel Wired for Management (WfM) specification. The PXE model enables server blades to load and execute a network bootstrap program (NBP) from a PXE server and to execute a pre-configured image. The image can be an operating system image created by software utilities or a boot diskette image.
Server Blade Configuration and Utilities — Ethernet NIC with 10/100 RJ-45 connector — TCP/IP networking and an IP address compatible with one of the following the iLO Diagnostic Port IP address or an assigned DHCP or static IP address — CD-ROM drive and/or diskette drive — Any of the following Java™ Runtime Environment versions: 1.3.1_02 1.3.1_07 1.3.1_08 1.4.1 for Windows users only 1.4.2 for Linux users only Access the Java Runtime Environment versions at http://java.sun.com/products/archive/index.
Server Blade Configuration and Utilities — CD-ROM drive — NFS installed — 1.5 GB of available disk space • Windows repository server (only required for Windows deployment) — Windows 2000 or Windows 2003 operating system installed — Network connection — CD-ROM drive — 1.
Server Blade Configuration and Utilities HP Systems Insight Manager HP SIM provides comprehensive management of ProLiant BL30p server blades, maximizing system availability and optimizing IT staff efficiency. HP SIM allows systems administrators to quickly identify hardware failures, isolate and update systems running out-of-date system software, and easily access onboard management resources. In addition, HP SIM version 4.
Server Blade Configuration and Utilities Automatic Server Recovery-2 ASR-2 is a feature that causes the system to restart when a catastrophic operating system error occurs, such as a blue-screen or kernel panic. A system fail-safe timer, the ASR-2 timer, starts when the System Management driver, also known as the Health Driver, is loaded. When the operating system is functioning properly, the system periodically resets the timer.
Server Blade Configuration and Utilities — For Linux operating systems, HP IML Viewer Application NOTE: You can only view the list from the Recovery/Integrated Management Log screen. Viewing the Event List To view the event list: 1. From HP SIM, select the appropriate server blade, then select View Device Data. The selected server blade appears with buttons around its perimeter. 2. Click Recovery. 3. Select Integrated Management Log. 4.
Server Blade Configuration and Utilities Refer to the HP ProLiant Essentials Rapid Deployment Pack CD for information on installing and running the Survey Utility. After you run the Survey Utility, you can view the IML by loading the output of the utility (typically called SURVEY.TXT) into a text viewer such as Microsoft Notepad. The event list follows the system slot information. After you open the text file, you can print it using the print feature of the viewer.
Server Blade Configuration and Utilities Table 5-2: Server Blade Event Messages Event Type Event Message Machine Environment Fan failure System Fan Failure (Fan X, Location) Overheat condition System Overheating (Zone X, Location) Main Memory Correctable error threshold exceeded Corrected Memory Error threshold passed (Slot X, Memory Module X) Corrected Memory Error threshold passed (System Memory) Corrected Memory Error threshold passes (Memory Module unknown) Processor Correctable error threshold
Server Blade Configuration and Utilities Configuration and Deployment Overview iLO Advanced can be a helpful debugging tool in the configuration and deployment process. HP recommends using iLO Advanced to follow the process. Refer to the “Integrated Lights-Out Advanced Management” section in this chapter for connection instructions. It is useful to set up and configure iLO for a server blade as an initial step to deployment.
Server Blade Configuration and Utilities Using iLO static IP bay configuration will: • Provide easier setup with automatic iLO address generation for all or a few selected bays. • Help avoid the costs of a DHCP infrastructure to support the server blade environment.
Server Blade Configuration and Utilities HP recommends selecting a reasonable starting IP address, with the last digit(s) of the address corresponding to the bay number of each server blade (example: 192.168.100.1 through 192.168.100.16), the user can build an easy-to-remember numbering system. 4. Reset Bay #1, if necessary. The server blade in Bay #1 must only be reset if you intend the server blade to use a Static IP Bay Configuration address by marking the feature enable mask for Bay #1.
Server Blade Configuration and Utilities Figure 5-1: Static IP Bay Configuration 5-22 HP ProLiant BL30p Server Blade Setup and Installation Guide
Server Blade Configuration and Utilities Standard Configuration Parameters Beginning IP Address (Bay 1)—Assigns the starting IP address. All IP addresses must be valid addresses. Ending IP Address (Bay 16)—Assigns the ending IP address. All IP addresses must be valid addresses. Subnet Mask—Assigns the subnet mask for the default gateway. This field may be filled in if either Static IP Bay Configuration or DHCP is enabled. The entire IP address range must conform to the subnet mask.
Server Blade Configuration and Utilities Enable iLO IP Address Assignment Bay #1 through Bay #16 checkboxes allow you to select which BL p-class server blades will be configured. You may Enable All, Clear All, or Apply the selection.
Server Blade Configuration and Utilities • ISIP_ENABLE is used to enable or disable the use of Static IP Bay Configuration. This attribute must appear inside the MOD_NETWORK_SETTINGS command block. The possible values are “Y” or “N.” It is case insensitive. This attribute is only applicable on server blades. • GET_ISIP_SETTINGS requests the respective iLO Static IP Bay Configuration settings. This attribute must appear inside the RACK_INFO command block.
Server Blade Configuration and Utilities Modify Network Settings to enable Static IP Bay Configuration Refer to the HP Integrated Lights-Out User Guide for information on DHCP and the manual setting of IP addresses.
Server Blade Configuration and Utilities PXE Deployment PXE enables server blades to load an image over the network from a PXE server, then execute it in memory. The first NIC on the server blade is the default PXE boot NIC, but any of the other NC series NICs can be configured to boot PXE. Refer to “Network-Based PXE Deployment” in this chapter for more information. NOTE: Actual NIC numeration depends on several factors, including the operating system installed on the server.
Server Blade Configuration and Utilities For product information and the latest RDP documentation, go to www.hp.com/servers/rdp SmartStart Scripting Toolkit The HP SmartStart Scripting Toolkit radically simplifies high-volume server deployment, enabling thousands of servers to be deployed quickly and easily.
Server Blade Configuration and Utilities • Through an existing network (out of the rack, with the diagnostic station): This method enables you to configure a server blade out of the rack by powering the server blade with the diagnostic station and connecting to an existing network through a hub. The IP address is assigned by a DHCP server on a network.
Server Blade Configuration and Utilities 6. Use the iLO Virtual Power Button feature to reboot the server blade. 7. After the server blade boots, follow the normal network installation procedure for an operating system. USB CD-ROM SmartStart simplifies the deployment process and facilitates loading the operating system. However, SmartStart does not prevent you from loading the operating system and drivers manually. For more information on SmartStart, refer to the HP website: www.hp.
Server Blade Configuration and Utilities • Through an existing network (out of the rack, with the diagnostic station): This method enables you to configure a server blade out of the rack by powering the server blade with the diagnostic station and connecting to an existing network through a hub. The IP address is assigned by a DHCP server on a network.
Server Blade Configuration and Utilities Using the Boot Diskette Server blades have two mechanisms for using the diskette: iLO Virtual Floppy and PXE. iLO Virtual Floppy Deployment To perform a boot diskette deployment: 1. Perform one of the following: — Insert the boot diskette into the client PC from which you are running the iLO Remote Console. — Use iLO Advanced to create an image file of the boot diskette. — Copy the image of the boot diskette to a location on the network or the client PC hard drive.
Server Blade Configuration and Utilities For optimal SAN connectivity, verify that: • The HP ProLiant BL30p server blade has the FC adapter installed, and that it is correctly installed in the server blade Refer to the HP Dual Port Fibre Channel Adapter (2-Gb) Installation Instructions • An FC-compatible interconnect is installed in the enclosureRefer to the documentation that shipped with the interconnect option • The enclosure management module firmware is up-to-dateRefer to the ProLiant BL p-Class
6 Connecting Local I/O Devices Using the Local I/O Cable Use the local I/O cable to perform some server blade configuration and diagnostic procedures. Connecting to a Server Blade through iLO To connect directly to iLO using the local I/O cable, you must have the following: • A client PC with a 10/100 Ethernet RJ-45 connector • A network cable with RJ-45 connectors To connect directly to iLO: IMPORTANT: Do not connect the local I/O cable to a hub when connecting to iLO.
Connecting Local I/O Devices 1. Connect one end of the RJ-45 network cable to the local I/O cable. 2. Connect the other end of the network cable to the 10/100 Ethernet RJ-45 connector on a client PC (2). Figure 6-1: Connecting an RJ-45 network cable IMPORTANT: Before removing the local I/O cable, completely log out of the current iLO session. Do not remove the local I/O cable when the Unit Identification LED (UID) is blinking. 3. Connect the local I/O cable to the I/O port on the server blade.
Connecting Local I/O Devices Figure 6-2: Connecting the local I/O cable to a server blade CAUTION: On the local I/O cable, the locking buttons are located on the sides of the server blade connector. Always be sure to squeeze the locking button(s) on the server blade connector before disconnecting the local I/O cable from I/O port. Failure to do so can result in damage to the equipment.
Connecting Local I/O Devices Connecting Directly to a Server Blade using Video and USB Devices To connect directly to the server blade, use the local I/O cable and any of the following USB devices: • Monitor • USB Hub • USB Keyboard • USB Mouse • USB CD-ROM • USB Floppy The devices can be connected to the local I/O cable in various configurations.
Connecting Local I/O Devices Directly Accessing a Server Blade with Local Keyboard, Video, and Mouse Use the following setup to access a server blade with local keyboard, video, and mouse: CAUTION: Disconnect the local I/O cable when not in use. The port and connector do not provide a permanent connection. Rear iLO connector performance degrades when the local I/O cable is in use, even when the iLO connector on the cable is not in use.
Connecting Local I/O Devices Directly Accessing a Server Blade with Local Media Devices Use the following setup to configure a server blade or load software updates or patches using a CD-ROM such as the SmartStart CD or a floppy drive: CAUTION: Disconnect the local I/O cable when not in use. The port and connector do not provide a permanent connection. Rear iLO connector performance degrades when the local I/O cable is in use, even when the iLO connector on the cable is not in use. 1.
Connecting Local I/O Devices 4. Connect the following to the USB hub: a. USB CD-ROM (4) and/or a USB diskette drive b. USB keyboard (5) c. USB mouse (6) NOTE: HP recommends the use of a USB hub when connecting a USB diskette and/or USB CD-ROM drive to the server blade. This provides more available USB connections.
A Server Blade Troubleshooting For a list of new server error messages that are specific to this server, refer to “Server Error Messages.” For information on LEDs and switches specific to the server blade, refer to “Front Panel LEDs, Button, and Port” in Chapter 1, “Server Blade Component Identification.” For information about general troubleshooting techniques, diagnostic tools, error messages, and preventative maintenance, refer to the HP ProLiant Servers Troubleshooting Guide on the Documentation CD.
Server Blade Troubleshooting When the Server Blade Does Not Start This section provides systematic instructions on what to try and where to go for help for the most common problems encountered during initial POST. The server blade must first complete this test each time you power up, before it can load the operating system and start running software applications. IMPORTANT: Always be sure that you have adequate system power applied to all the rack components before troubleshooting the server blade.
Server Blade Troubleshooting 4. If the system does not complete POST or start loading an operating system: a. Use the iLO remote console, the video connection provided through the local I/O cable connectors, or the iLO system status page to identify POST messages. Refer to the HP Integrated Lights-Out User Guide. b. Refer to the HP ProLiant Servers Troubleshooting Guide. 5. Be sure the server blade is not rebooting repeatedly: a.
Server Blade Troubleshooting — Copyright information — Processor initialization — iLO initialization — Array controller initialization — PXE initialization 9. The operating system loads to complete the boot process. If the server blade completes POST and attempts to load the operating system, refer to “Problems After Initial Boot” in this appendix.
Server Blade Troubleshooting Server Blade Diagnostic Steps If the server blade does not power up, or powers up but does not complete POST, answer the questions in Table A-1 to determine appropriate actions based on the symptoms observed. According to the answers you give, you are directed to the appropriate table that immediately follows. Table A-1: Diagnostic Steps Question Action Question 1: Is the server blade power on/standby LED illuminated? If yes, continue to question 2.
Server Blade Troubleshooting Table A-2: Is the Server Blade Power on/standby LED Illuminated? Answer Possible Reasons Possible Solutions No A broken connection exists between the server blade enclosure and server blade sleeve. Do the following: 1. Verify that power is applied to the infrastructure. A broken connection exists between the server blade sleeve and server blade. 2. Remove the server blade from the server blade sleeve. 3.
Server Blade Troubleshooting Table A-2: Is the Server Blade Power on/standby LED Illuminated? continued Answer Yes Possible Reasons Possible Solutions • Move the server blade and sleeve into a different slot to determine if the server blade, the server blade sleeve, or the server blade enclosure is the source of the problem. • Contact an authorized service provider for replacement parts and service. If the power on/standby LED is illuminated, refer to Table A-3.
Server Blade Troubleshooting Table A-3: Is the Server Blade Power on/standby LED Green? Answer Possible Reasons Possible Solutions No, it is amber Power button has not been pressed firmly; if this mode is selected. 1. With the system powered down and the server blade removed from the sleeve, be sure that the proper connections exist among the power converter module, system board, and power button/LED board. Management modules are not properly cabled. 2.
Server Blade Troubleshooting Table A-4: Is the Server Blade Health LED Solid Green? Answer Possible Reasons Possible Solutions No, it is amber. A processor is in pre-failure condition. Do the following: 1. Remove the server blade from the server blade enclosure. The memory bank has mismatched DIMMs installed. 2. With the system powered down, remove the access panel. The memory bank has an unsupported DIMM type installed. 3. Visually inspect the system for damage. 4.
Server Blade Troubleshooting Table A-4: Is the Server Blade Health LED Solid Green? continued Answer Possible Reasons Possible Solutions If the health LED is still not solid green, do one of the following: • Use the optional diagnostic station to power the server blade and use the iLO remote console to continue the diagnosis. • Use the optional diagnostic station to power the server blade and use the local I/O cable connectors, depending on the server blade model, to continue the diagnosis.
Server Blade Troubleshooting Table A-4: Is the Server Blade Health LED Solid Green? continued Answer Possible Reasons Possible Solutions No, it is flashing green. The server blade is still in POST. If the flashing continues after 1 minute, the following conditions may apply: Wait for the server blade to complete POST. • Nonvolatile RAM (NVRAM) may be corrupted. • The system ROM may be corrupted. • Both the system ROM and redundant ROM may be corrupted. Clear the system configuration.
Server Blade Troubleshooting Table A-4: Is the Server Blade Health LED Solid Green? continued Answer Possible Reasons Possible Solutions No, it is red A processor has failed. Do the following: Processor 1 is not installed. 1. A processor is an unsupported type. Remove the server blade from the server blade enclosure. 2. Processors are mismatched (speed and/or type). With the system powered down, remove the access panel. 3. Visually inspect the system for damage. An embedded PPM has failed.
Server Blade Troubleshooting Table A-5: Is the iLO Remote Console Displaying Error Information? Answer Solution No An iLO problem exists. Refer to the HP Integrated Lights-Out User Guide that ships with the server blade. Yes Error and event logs are available for diagnosis. Determine the next action by observing POST progress and error messages. Use the iLO system status page or use the local I/O cable connectors, depending on the server blade model, to help determine the problem.
Server Blade Troubleshooting Figure A-1: Blade sleeve board and server blade LED locations (shown with blade sleeve cover removed) Table A-6: Blade Sleeve Board and Server Blade LED Locations A-14 LED LED Name (System Board Descriptor) 1 Blade sleeve power LED (CR6) 2 Power converter module LED (CR9) 3 FC LED (CR3) 4 Blade sleeve power LED (CR7) HP ProLiant BL30p Server Blade Setup and Installation Guide
Server Blade Troubleshooting Each condition in Table A-7 is determined by the corresponding LED located on either the blade sleeve board or the system board. Table A-7: Power Troubleshooting Table Blade Sleeve Power LED Power Converter Module LED Possible Reasons On On The power is good. On Off A power problem exists with the server blade. or The power converter module needs replacing. Off Off Power problem with the diagnostic station. or The blade sleeve board needs to be replaced.
Server Blade Troubleshooting IMPORTANT: Do not perform these procedures until directed to do so by the troubleshooting tables in this appendix. To complete these procedures, you must change physical settings on the system configuration switch (SW1). For switch locations and positions, refer to “Front Panel LEDs, Button, and Port” in Chapter 1, “Server Blade Component Identification.
Server Blade Troubleshooting Clearing the System Configuration To clear the system configuration: 1. Power down the server blade: a. Press the Power On/Standby button on the front of the server blade. b. Use the virtual power button feature in the iLO remote console. 2. Disconnect the server blade from all power sources: a. Remove the server blade from the server blade enclosure and set it on a flat, level surface. b. Disconnect the server blade from the diagnostic station. 3.
Server Blade Troubleshooting 8. Change position 6 of SW1 to off. 9. Repeat steps 4 through 6. IMPORTANT: When the server blade boots after NVRAM is cleared, a delay of up to 2 minutes is normal. During this delay, the system appears non-functional. Do not attempt any procedures during the delay. Accessing the Redundant ROM If the system ROM is corrupted, you can set the system to use the backup version or redundant ROM. To use the redundant ROM: 1. Power down the server blade: a.
Server Blade Troubleshooting 7. Change positions 1, 5, and 6 of SW1 to off. 8. Repeat steps 4 and 5. If both the current and backup versions of the ROM are corrupt, you must return the system board for a service replacement. Refer to the HP ProLiant BL p-Class System Maintenance and Service Guide and contact an authorized reseller. Problems After Initial Boot Once the server blade has passed POST, you may still encounter errors, such as an inability to load the operating system.
B Battery Replacement System Board Battery Replacement When the server blade no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is usually about 5 to 10 years. Use an HP 540-mAh, lithium, 3-V replacement battery (spare P/N 234556-001). To install a new battery: 1. Access the internal server blade components.
Battery Replacement 2. Locate the battery holder on the system board. 3. Push the tab aside, and pull the existing battery straight up. Figure B-1: Battery holder WARNING: For proper battery disposal, refer to the “Battery Replacement Notice” section in Appendix C, “Regulatory Compliance Notices.” 4. To install the new battery, push it into the socket until the tab locks in place. CAUTION: The battery is keyed to install only with the positive side facing the tab.
C Regulatory Compliance Notices Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certification and identification, your product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this series number.
Regulatory Compliance Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Canadian Notice (Avis Canadien) This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Regulatory Compliance Notices Korean Notice BSMI Notice Battery Replacement Notice Your computer is provided with an internal lithium battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Unless specific replacement instructions are provided as part of this guide, replacement is to be done by an authorized service provider using the spare designated for this product.
Regulatory Compliance Notices WARNING: Your computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. There is risk of fire and burns if the battery pack is not handled properly. To reduce the risk of personal injury, • Do not attempt to recharge the battery. • Do not expose to temperatures higher than 60°C (140°F). • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
D Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Electrostatic Discharge Grounding Methods Several methods for grounding are available. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: • Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum of 1 megohm ± 10 percent resistance in the ground cords. To provide proper ground, wear the strap snug against the skin.
Index A accessing internal server blade components 3-1 redundant ROM 5-5, A-18 accumulators C-4 alkaline battery warning C-4 Altiris eXpress Deployment Server 5-27 authorized reseller xi Automatic Server Recovery-2 (ASR-2) 5-15 B batteries disposal C-4 life B-1 part number B-1 recycling or disposal C-4 replacement C-3 BIOS enhanced RAID 5-9 enabling 5-10 important considerations 5-10 BIOS, upgrading 5-7 blade sleeve, installing 3-3 blank 3U server blade 3-3 6U server blade 3-2 processor 4-1, 4-4, 4-6 boo
Index connecting, local I/O cable 6-1 connectors local I/O cable 1-7, 1-8 system board 1-1 E D deployment CD-ROM image 5-29 diskette image 5-30 HP ProLiant Essentials Rapid Deployment Pack (RDP) 5-27 iLO 5-29, 5-32 infrastructure 5-26 methods 5-26 Preboot eXecution Environment (PXE) 5-11 PXE 5-27 software 5-1 USB CD-ROM 5-30 utilities 5-1 diagnostic steps, server blades A-5 Diagnostics Utility 5-14 downloading 5-14 running 5-14 DIMMs See also memory installation guidelines 4-13 installing 4-13 key slots
Index HP ProLiant Integration Module 5-27 HP Systems Insight Manager (HP SIM) 5-14 HP website xi IP address assign 5-3, 5-19 local I/O cable 6-1 J I identifying front panel buttons 1-4 front panel LEDs 1-4 local I/O cable connectors 1-7, 1-8 server blade components 1-1 system board connectors 1-1 iLO IP address assignment, enabling 5-24 iLO ROM-Based Setup Utility 5-4 installing blade sleeve 3-3 DIMMs 4-13 dual port Fibre Channel adapter 4-15 hard drive 4-7 heatsink 4-5 processor 4-4 server blades 3-4 In
Index N network-based Preboot eXecution Environment (PXE) deployment 5-11, 5-27 NICs LED, location 1-5 normal power up sequence A-3 notices European Union C-2 notices battery replacement C-3 BSMI C-3 Canadian C-2 Federal Communications Commission C-1 Japanese C-2 Korean C-3 O Online Flash Utility 5-6 operating systems 5-31 override, power-up 2-1 P part number, battery B-1 POST error messages use for diagnosis A-13 where to find A-1 power button 2-1 function 2-2 location 1-5 long press 2-1 momentary press
Index replacing battery C-3 requirements, local I/O cable 6-1 RFI/EMI connector hoods C-2 ROM flashing See remote ROM flash redundant See redundant ROM support 5-5 ROM-Based Setup Utility (RBSU) 5-7 default settings 5-8 definition 5-7 navigating 5-8 ROM-Based Setup Utility (RBSU), iLO 5-4 ROMPaq Utility 5-7 ROMs iLO 5-6 power management module 5-6 server blade management module 5-6 server blade system 5-6 S safety product C-2 SAN 5-32, 5-33 server blade cautions 3-1 components 1-1 configuring using SmartS
Index switches, system maintenance (SW1) 1-5 symbols in text ix on equipment vii system board battery replacement B-1 connectors 1-1 safety D-1 system maintenance switch (SW1) 1-5 System Maintenance Switch (SW1), settings 1-6 system power LED, troubleshooting A-6, A-8 system, firmware 5-6 T technical support x telephone numbers x, xi thermal interface media 4-5 toe straps D-2 tools, conductive D-2 troubleshooting DIMMs A-9 event messages 5-18 initial boot A-19 no amber on system power LED A-6 no green on
