ProLiant DL140 Generation 2 Server Installation Sheet

ManualsBrandsHP ManualsServerHP ProLiant DL140 G2 Server

HP ProLiant DL140

Generation 2 Server

Installation Sheet

Read instructions completely before beginning

installation procedure

any, L.P.

The information contained herein is subj

ect to change withou

t notice. The only

warranties for HP products and services are set forth in the e

xpress warranty

statements accompanying such products and services. Not

hing herein should be

construed as constituting an additional warranty. HP shal

l not be liable for technical

or editorial errors or omissions contained herein.

Intel is a registered trademark of Intel Corporation or its subsidiaries i

n the

United States and other countries.

HP ProLiant DL140 Generation 2 Server Installation Sheet

Second Edition (March 2005)

Part Number 381739-002

Identifying Server Components

Front Panel Components

Table 1: Front Panel Components

Item Icon Component

1 Hard disk drive (HDD) bays

2 Optical media device bay

Unit identification (UID) button with LED

indicator (blue)

System health LED indicator (amber)

Activity/link status LED indicators for NIC 1 and

NIC 2 (green)

HDD activity LED indicator (green)

Power button with LED indicator

(bicolor: green and amber)

8 Thumbscrews for the front bezel

USB 2.0 ports

Rear Panel Components

Table 2: Rear Panel Components

Item Icon Component

1 Ventilation holes

2 Thumbscrew for the top cover

3 Thumbscrews for the PCI riser board assembly

4 Low profile 64-bit/133 MH

z PCI-X riser board slot

cover

5 Standard height/full-

length 64-bit/133 MHz PCI-X

riser board slot cover

6 Power supply cable socket

GbE LAN ports for NIC 1 and NIC 2 (RJ-45)

UID button with LED indicator (blue)

USB 2.0 ports (black)

Video port (blue)

Serial port (teal)

PS/2 keyboard port (purple)

PS/2 mouse port (green)

10/100 Mbps LAN port for IPMI management

(RJ-45)

NOTE: The three LAN ports each has its own LED indicators for

activity/link status and network speed.

Summary of content (8 pages)

PAGE 1
Identifying Server Components HP ProLiant DL140 Generation 2 Server Front Panel Components Installation Sheet Table 1: Front Panel Components Item Icon 1 Component Hard disk drive (HDD) bays 2 Optical media device bay 3 Unit identification (UID) button with LED indicator (blue) 4 System health LED indicator (amber) 5 Activity/link status LED indicators for NIC 1 and NIC 2 (green) 6 HDD activity LED indicator (green) 7 Power button with LED indicator (bicolor: green and amber) 8 Thumbscre
PAGE 2
Table 3: System Board Components continued System Board Components Item Component Code 18 U18 Intel mPGA604 processor 1 socket 19 20 U6 Intel mPGA604 processor 0 socket CN40 9-pin connector for the front USB 2.
PAGE 3
Server Configuration Guidelines Observe the following important guidelines before performing any of the configuration steps listed in the next section. • For safety information and detailed procedures related to step 3 of the “Server Configuration Overview” section, refer to Chapter 2 of the HP ProLiant DL140 Generation 2 Server Maintenance and Service Guide.
PAGE 4
Installing a Memory Module The system has eight DIMM slots that support up to 16 GB maximum system memory (2 GB in each of the eight DIMM slots). 7. Perform the post-installation procedures described earlier. Installing a PCI Expansion Board Memory Installation Guidelines Observe the following important guidelines when installing memory modules: • Use only HP supported PC2-3200 (400 MHz) registered ECC DIMMs in 512 MB, 1 GB, or 2 GB capacities • Memory modules must be installed in pairs of the same size.
PAGE 5
PCI Riser Board Expansion Slots The two PCI-X riser boards attached to the PCI riser board assembly convert the functionality of the system board expansion slots to a pair of slots positioned at a 90° angle from the system board. Item 1 2 4. Pull out the slot cover from the selected slot. Store it for reassembly later. CAUTION: Do not discard the slot cover. If the expansion board is removed in the future, the slot cover must be reinstalled to maintain proper cooling.
PAGE 6
• Hard drives installed in the server are labeled as Device 0 and Device 1 from left to right when viewed from the front of the server. Installing the SCSI controller board in the standard height/fulllength expansion slot 8. Connect the necessary cable(s) to the board. Refer to the documentation that came with the board. 9. Perform the post-installation procedures described earlier. Installing a Hard Drive The server’s two 1-inch hard disk drive bays support both non-hot-plug SCSI and SATA drives.
PAGE 7
IMPORTANT: If you removed a hard drive without plans of installing a new one, you must reinstall the mounting screws at their pre-installed location for future use, then reinstall the HDD carrier in the chassis for the proper cooling of the system. Configuring a SCSI Hard Drive The steps listed below give an overview of the SCSI hard drive configuration procedure: 1. Install the SCSI hard drive. 2. Install the SCSI controller board.
PAGE 8
Installing an Optional CD-ROM or DVD Drive 4. Install the new optical drive in its carrier: a. Align the optical drive in the carrier. b. Secure the drive with two mounting screws. The optical media device bay supports the installation of a slim-type CD-ROM or DVD-ROM drive. Go to the HP website at http://www.hp.com/ and refer to the options list for this server model for a list of supported optical media drives. To install an optional CD-ROM or DVD drive: 1.