HP ProLiant DL165 Generation 5 Server Installation Sheet

ManualsBrandsHP ManualsServerHP ProLiant DL165 G5 Server

HP ProLiant DL165

Generation 5 Server

Installation Sheet

First edition (September 2007)

Part number 449866-001

Opening the Server

The top cover and the top middle cover are detachable. You need to remove the

top cover before you can remove or replace a server component.

To remove the top cover:

1. Loosen the captive screw on the top cover with the T-15 wrench provided.

2. Slide the cover approximately 1.25 cm (0.5 in) toward the rear of the unit and

then lift the cover to detach it from the chassis.

3. Lift the top cover away from the chassis.

Figure 3 Removing the top cover

To remove the top middle cover:

1. Remove the four screws (one on each side of the chassis and two on the top

middle cover) that secure the top middle cover to the chassis with the T-15

wrench provided.

2. Lift the top middle cover away from the chassis.

Figure 4 Removing the top middle cover

Installing a Hard Drive

The drive bays on the front panel can accommodate up to four hard drives. The

server supports both SAS and SATA hard drives.

CAUTION: Drives can be damaged by static electricity. Before handling

drives, touch an unpainted metal surface to discharge static electricity.

To install a hard drive in the server:

1. Remove the hard drive blank from front of system, if installed.

2. Push the hard drive assembly into the drive bay until it stops.

3. Press the HDD carrier latch inward until it clicks.

Important Safety Information

Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.

Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.

Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.

Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.

Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.

Identifying Server Components

Front Panel Components

Figure 1 Front panel components

Item Description

1 Thumbscrews for rack mounting

2 Optical disk drive bay

3 Serial number pull tab

4 Two front USB 2.0 ports

5 Unit identiﬁcation (UID) LED button

6 System health LED

7 NIC1 LED

8 NIC2 LED

9 Power button

10 HDD LED

11 Hard disk drive (HDD) bays 1, 2, 3, and 4

Rear Panel Components

Figure 2 Rear panel components

Item Description

1 Power supply cable socket

2 PS/2 mouse port (green)

3 GbE LAN port for NIC2

4 Captive thumbscrew for top cover

5 Serial port (teal)

6 Low proﬁle/Half length expansion slot

7 Full height/Full length expansion slot

8 T10/T15 Wrench

9 Thumbscrew for PCI cage

10 UID LED button

11 VGA port

12 HP LO100i Management LAN Port

13 Two rear USB 2.0 ports

14 GbE LAN port for NIC1/Management

15 PS/2 keyboard port (purple)

Server conﬁguration resources

In addition to this Installation Sheet, other resources are available for more

information regarding the conﬁguration and maintenance of your server:

• For safety information and detailed procedures relating to installation of options,

refer to any installation instructions that came with the option, as well as the

HP ProLiant DL165 G5 series Server Maintenance and Service Guide

• For safety information and detailed procedures related to the rest of the steps

listed in the “Server Conﬁguration Overview”section, refer to relevant chapter

of the HP ProLiant DL100 Series Server User Guide

• For information relating to system BIOS conﬁguration and operating system

installation, refer to relevant section of the HP ProLiant DL165 Generation 5

Server Software Conﬁguration Guide

• Refer to the HP ProLiant DL165 Generation 5 Server Support and Documentation

CD for additional information and updates not provided in this installation

sheet. You can also access additional information and documentation from the

HP website at http://www.hp.com/, either by connecting directly or through

the Support CD.

Server Conﬁguration Overview

The steps listed below give an overview of the necessary setup procedures for

preparing the HP ProLiant DL165 Generation 5 server for operation:

1. Connect the AC power cord and peripheral devices.

2. Power up the server.

3. Press F10 to enter BIOS setup.

4. Note the server BIOS version.

5. Verify the server BIOS version against the latest BIOS version listed for this

server on the HP website: http://www.hp.com.

6. If you do not have the latest BIOS, update the BIOS now. Refer to the

ProLiant DL165 Generation 5 Server Maintenance and Service Guide available

on the HP website: http://www.hp.com/

7. Install a supported operating system of your choice. For detailed procedures,

refer to the documentation provided by the operating system vendor. For a list

of operating systems supported by your ProLiant server, go to

http://www.hp.com/go/supportos

Pre- and post-installation

procedures

When installing additional options in your HP ProLiant DL165 Generation 5 server,

observe the following procedures:

Pre-installation procedures

1. Turn off the server and all the peripherals connected to it.

2. Disconnect the AC power cord from the power supply connector located on the

server rear panel to reduce the risk of electrical shock.

3. If server is installed in a rack, remove server and place it on a ﬂat surface.

4. Remove the top cover by following the procedure described later in the

“Opening the Server” section.

Post-installation procedures

1. Be sure all components are installed according to the described step-by-step

instructions.

2. Check to make sure you have not left loose tools or parts inside the server.

3. Reinstall the PCI cage, air bafﬂe, peripherals, and system cables that you have

removed.

4. Reinstall the top cover.

5. Reinstall server into rack.

6. Connect all external cables and the AC power cord to the system.

7. Press the power button on the front panel to turn on the server.

Legal notices

The information contained herein is subject to change without notice. The only warranties

for HP products and services are set forth in the express warranty statements accompanying

such products and services. Nothing herein should be construed as constituting an additional

warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

AMD is a trademark of Advanced Micro Devices, Inc.

Summary of content (4 pages)

PAGE 1
HP ProLiant DL165 Generation 5 Server Installation Sheet Identifying Server Components Server conﬁguration resources Opening the Server Front Panel Components In addition to this Installation Sheet, other resources are available for more information regarding the conﬁguration and maintenance of your server: • For safety information and detailed procedures relating to installation of options, refer to any installation instructions that came with the option, as well as the HP ProLiant DL165 G5 series Ser
PAGE 2
HP ProLiant DL165 Generation 5 Server Installation Sheet Identifying Server Components Server conﬁguration resources Opening the Server Front Panel Components In addition to this Installation Sheet, other resources are available for more information regarding the conﬁguration and maintenance of your server: • For safety information and detailed procedures relating to installation of options, refer to any installation instructions that came with the option, as well as the HP ProLiant DL165 G5 series Ser
PAGE 3
Figure 5 Installing the hot-plug hard drive assembly To install a hard drive in the server: To install a memory module: 1. Remove the hard drive blank from front of system, if installed. 1. Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and then press the module fully into the slot. 2. Push the hard drive assembly into the drive bay until it stops (step 1 in ﬁgure 8). 3.
PAGE 4
Figure 5 Installing the hot-plug hard drive assembly To install a hard drive in the server: To install a memory module: 1. Remove the hard drive blank from front of system, if installed. 1. Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and then press the module fully into the slot. 2. Push the hard drive assembly into the drive bay until it stops (step 1 in ﬁgure 8). 3.