ProLiant ML530 Servers Maintenance and Service Guide
Table Of Contents
- Compaq ProLiant ML530 Servers Maintenance and Service Guide
- Notice Page
- Table of Contents
- About This Guide
- Chapter 1: Illustrated Parts List
- Chapter 2: Removal and Replacement Procedures
- Electrostatic Discharge Information
- Symbols on Equipment
- Preparation Procedures
- Tower Model Front Bezel Door
- Rack Mount Bezel
- Access Panel
- Fans
- Removable Media and Mass Storage Devices
- Cable Routing Diagrams
- System Board Tray
- System Board Components
- Hot Plug Power Supplies
- Power Backplane Board
- Power On/Standby Switch
- Chapter 3: Diagnostics and Troubleshooting
- Diagnostic Tools Utility Overview
- Default Configuration
- Utilities Access
- Power On Self Test
- Diagnostics Software
- Steps for Diagnostics
- 100–199, Primary Processor Test Error Codes
- 200–299, Memory Test Error Codes
- 300–399, Keyboard Test Error Codes
- 400–499, Parallel Printer Test Error Codes
- 500–599, Video Display Unit Test Error Codes
- 600–699, Diskette Drive Test Error Codes
- 800–899, Video Board Test Error Codes
- 1100–1199, Serial Test Error Codes
- 1200–1299, Modem Communications Test Error Codes
- 1700–1799, Hard Drive Test Error Codes
- 1900–1999, Tape Drive Test Error Codes
- 2400–2499, Advanced VGA Board Test Error Codes
- 6000–6099, Compaq NIC Boards Test Error Codes
- 6500–6599, SCSI Hard Drive Test Error Codes
- 6700–6799, SCSI Tape Drive Test Error Codes
- 8600–8699, Pointing Device Interface Test Error Codes
- Array Diagnostic Utility
- Integrated Management Log
- Rapid Error Recovery
- Remote Service Features
- ROMPaq Error Recovery Options
- Compaq Insight Manager
- Chapter 4: Connectors, Switches, Jumpers, and LED Indicators
- Chapter 5: Physical and Operating Specifications
- Index
Diagnostics and Troubleshooting 3-55
Rapid Error Recovery
Compaq servers provide rapid recovery services for diagnosing and recovering from errors.
These tools are available for local and remote diagnosis and recovery.
Rapid recovery means fast identification and resolution of complex faults. The Rapid Recovery
Engine and Insight Management Agents notify the system administrator when a failure occurs,
ensuring that the server experiences minimal downtime. You enable these features through the
System Configuration Utility. These integrated server management features are:
■ Automatic Server Recovery-2 (ASR-2)
■ ASR-2 Integrated Management Log Messages
■ Storage Fault Recovery Tracking
■ Storage Automatic Reconstruction
■ Network Interface Fault Recovery Tracking
■ Memory Fault Recovery Tracking (with option upgrade kit)
These are discussed in more detail on the server documentation CD.
Automatic Server Recovery-2
Automatic Server Recovery-2 (ASR-2) lets the server restart automatically from the operating
system or the Compaq Utilities. To use this feature, you must use the System Configuration
Utility to install Compaq Utilities in the system partition.
You can enable the ASR-2 feature to restart a server after a critical hardware or software error
occurs. If a critical error occurs, the server records the error information in the Integrated
Management Log, restarts the system, and pages you. Using the Compaq System Configuration
Utility, configure the system for automatic recovery or for attended local or remote access to
diagnostic and configuration tools.
NOTE: ASR-2 is available only on operating systems using the ASR-2 drivers provided by Compaq.
You can also configure ASR-2 to page an administrator when the system restarts. ASR-2
depends on the application and driver that routinely notify the ASR-2 hardware of proper
system operations. If the time between ASR-2 notifications exceeds the specified period, ASR-2
assumes a fault has occurred and initiates the recovery process.
To configure ASR-2:
1. Run the System Configuration Utility.
2. Select View and Edit Details.
3. Set the software error recovery status to Enabled.
4. Set the software error recovery timeout.