ProLiant ML530 Servers Maintenance and Service Guide
Table Of Contents
- Compaq ProLiant ML530 Servers Maintenance and Service Guide
- Notice Page
- Table of Contents
- About This Guide
- Chapter 1: Illustrated Parts List
- Chapter 2: Removal and Replacement Procedures
- Electrostatic Discharge Information
- Symbols on Equipment
- Preparation Procedures
- Tower Model Front Bezel Door
- Rack Mount Bezel
- Access Panel
- Fans
- Removable Media and Mass Storage Devices
- Cable Routing Diagrams
- System Board Tray
- System Board Components
- Hot Plug Power Supplies
- Power Backplane Board
- Power On/Standby Switch
- Chapter 3: Diagnostics and Troubleshooting
- Diagnostic Tools Utility Overview
- Default Configuration
- Utilities Access
- Power On Self Test
- Diagnostics Software
- Steps for Diagnostics
- 100–199, Primary Processor Test Error Codes
- 200–299, Memory Test Error Codes
- 300–399, Keyboard Test Error Codes
- 400–499, Parallel Printer Test Error Codes
- 500–599, Video Display Unit Test Error Codes
- 600–699, Diskette Drive Test Error Codes
- 800–899, Video Board Test Error Codes
- 1100–1199, Serial Test Error Codes
- 1200–1299, Modem Communications Test Error Codes
- 1700–1799, Hard Drive Test Error Codes
- 1900–1999, Tape Drive Test Error Codes
- 2400–2499, Advanced VGA Board Test Error Codes
- 6000–6099, Compaq NIC Boards Test Error Codes
- 6500–6599, SCSI Hard Drive Test Error Codes
- 6700–6799, SCSI Tape Drive Test Error Codes
- 8600–8699, Pointing Device Interface Test Error Codes
- Array Diagnostic Utility
- Integrated Management Log
- Rapid Error Recovery
- Remote Service Features
- ROMPaq Error Recovery Options
- Compaq Insight Manager
- Chapter 4: Connectors, Switches, Jumpers, and LED Indicators
- Chapter 5: Physical and Operating Specifications
- Index
Index 5
Abnormal Program
Termination 3-65
ASR-2 detected by ROM 3-65
ASR-2 Test Event 3-65
Automatic Server Recovery
Base Memory Parity
Error 3-65
Extended Memory Parity
Error 3-65
Memory Parity Error 3-65
Reset Limit Reached 3-65
Battery Failing 3-65
Caution, Temperature
Exceeded 3-65
Diagnostic Error 3-65
Error Detected On Boot
Up 3-65
NMI
Automatic Server Recovery
Timer Expiration 3-66
Expansion Board
Error 3-66
Expansion Bus Master
Time-Out 3-66
Expansion Bus Slave
Time-Out 3-66
Fail-Safe Timer
Expiration 3-66
PCI Bus Parity Error 3-66
Processor Parity Error 3-66
Software Generated
Interrupt Detected
Error 3-66
Processor Exception 3-66
Processor Prefailure 3-66
Required System Fan
Failure 3-66
Server Manager Failure 3-66
UPS A/C Line Failure Shutdown
or Battery Low 3-66
error messages
A Critical Error occurred prior to
this power-up 3-8
Accelerator board not
detected 3-39
Accelerator error log 3-39
Accelerator parity read 3-39
Accelerator parity write 3-39
accelerator status
Cache was automatically
configured 3-39
Data in the cache was
lost 3-39
Dirty data detected has
reached limit 3-39
Dirty data detected. Unable
to write 3-39
Excessive ECC errors 3-40
Obsolete data detected 3-40
Obsolete data was
discarded 3-40
Obsolete data was
flushed 3-40
Possible data loss in
cache 3-40
Temporarily disabled 3-40
Unrecognized status 3-40
Valid data found at
reset 3-41
Warranty alert 3-41
Adapter/NVRAM ID
mismatch 3-41
Array accelerator battery pack X
not fully charged 3-41
Array accelerator battery pack X
below reference
voltage 3-41
beeps only 3-23
Board in use by expand
operation 3-41
Board not attached 3-41
Configuration signature is
zero 3-41
configuration signature
mismatch 3-41
controller
communication failure
occurred 3-41
firmware needs
upgrading 3-41
is not configured 3-42
located in special video
slot 3-42
reported POST error 3-42
restarted with a signature of
zero 3-42
controller detected. NVRAM
configuration not
present 3-41
Disable command issued 3-42
drive (bay) X
firmware needs
upgrading 3-42
has insufficient capacity for
its configuration 3-42
has invalid M&P
stamp 3-42
has loose cable 3-42
is a replacement drive 3-42
is a replacement drive
marked OK 3-43