ProLiant ML530 Servers Maintenance and Service Guide
Table Of Contents
- Compaq ProLiant ML530 Servers Maintenance and Service Guide
- Notice Page
- Table of Contents
- About This Guide
- Chapter 1: Illustrated Parts List
- Chapter 2: Removal and Replacement Procedures
- Electrostatic Discharge Information
- Symbols on Equipment
- Preparation Procedures
- Tower Model Front Bezel Door
- Rack Mount Bezel
- Access Panel
- Fans
- Removable Media and Mass Storage Devices
- Cable Routing Diagrams
- System Board Tray
- System Board Components
- Hot Plug Power Supplies
- Power Backplane Board
- Power On/Standby Switch
- Chapter 3: Diagnostics and Troubleshooting
- Diagnostic Tools Utility Overview
- Default Configuration
- Utilities Access
- Power On Self Test
- Diagnostics Software
- Steps for Diagnostics
- 100–199, Primary Processor Test Error Codes
- 200–299, Memory Test Error Codes
- 300–399, Keyboard Test Error Codes
- 400–499, Parallel Printer Test Error Codes
- 500–599, Video Display Unit Test Error Codes
- 600–699, Diskette Drive Test Error Codes
- 800–899, Video Board Test Error Codes
- 1100–1199, Serial Test Error Codes
- 1200–1299, Modem Communications Test Error Codes
- 1700–1799, Hard Drive Test Error Codes
- 1900–1999, Tape Drive Test Error Codes
- 2400–2499, Advanced VGA Board Test Error Codes
- 6000–6099, Compaq NIC Boards Test Error Codes
- 6500–6599, SCSI Hard Drive Test Error Codes
- 6700–6799, SCSI Tape Drive Test Error Codes
- 8600–8699, Pointing Device Interface Test Error Codes
- Array Diagnostic Utility
- Integrated Management Log
- Rapid Error Recovery
- Remote Service Features
- ROMPaq Error Recovery Options
- Compaq Insight Manager
- Chapter 4: Connectors, Switches, Jumpers, and LED Indicators
- Chapter 5: Physical and Operating Specifications
- Index
Diagnostics and Troubleshooting 3-9
Table 3-2
POST Error Messages
continued
Error Code Audible Beeps Probable Source of Problem Recommended Action
174-Configuration/
Slot Mismatch Device
Not Found
None EISA or PCI board not found. Run the System Configuration
Utility and correct.
175-Configuration/
Slot Mismatch Device
Found
None EISA or PCI board added,
configuration not updated.
Run the System Configuration
Utility and correct.
177-Configuration
Not Complete
None Incomplete system configuration Run the System Configuration
Utility and correct.
178-Processor
Configuration Invalid
None Processor type or step does not
match configuration memory.
Run the System Configuration
Utility and correct.
180-Log Reinitialized None IML reinitializing due to log
corruption.
Event message only, no action
required.
201-Memory Error None RAM failure Run Diagnostics. Replace failed
assembly as indicated.
203-Memory
Address Error
None RAM failure Run Diagnostics. Replace failed
assembly as indicated.
207-Invalid Memory
Configuration –
Check DIMM [SIMM]
Installation
None Memory module installed
incorrectly.
Verify placement of memory
modules.
208-Invalid Memory
Speed – Check DIMM
[SIMM] Installation
1 long, 1 short The speed of the memory is not
compatible with the server.
Verify the speed of the memory
modules installed, then check
your server’s user
documentation, and replace the
speed as indicated.
209-Memory
Detection Failure.
Check Memory
Installation
1 long, 1 short Unable to size memory. Check DIMM installation and, if
error persists, call your Compaq
service provider.
211-Cache Switch
Set Incorrectly
None Switch not set properly during
installation or upgrade.
Verify switch settings.
212-System
Processor Failed/
Mapped Out
1 short Processor in slot X failed. Run Diagnostics and replace
failed processor.
214-DC-DC
Converter Failed
None PowerSafe Module (DC-DC
Converter) failed.
Run Diagnostics. Replace failed
assembly as indicated.
218-Cache
Accelerators Not
Installed. System
Halted.
None Cache accelerators not installed
or improperly installed.
Check cache accelerator
installation.
219-Tag Update
Rules SRAM Failure.
System Halted
None Catastrophic chipset failure. Call Compaq service provider.
continued