HP ProLiant SL165z G7 Server Maintenance and Service Guide Part number 602406-001 First edition March 2010
Legal notices © Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents Customer self repair ............................................................................................................................... 5 Parts only warranty service........................................................................................................................ 5 Illustrated parts catalog ......................................................................................................................... 16 Mechanical components ...........................
BIOS Setup Utility .................................................................................................................................. 83 Accessing the BIOS Setup Utility .............................................................................................................. 83 Navigating through the Setup Utility .................................................................................................... 84 Setup Utility menu bar ................................................
Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory.
Réparation par le client (CSR) Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement.
Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
Customer self repair HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu.
Reparaciones del propio cliente Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de realizar sustituciones de componentes defectuosos.
Customer self repair Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd.
Reparo feito pelo cliente Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se, durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao cliente.
Customer self repair 12
Customer self repair 13
Customer self repair 14
Customer self repair 15
Illustrated parts catalog Mechanical components Item Description Spare part number Customer self repair 1 Fan blank 2A Air baffle 1 607824-001 Mandatory 2B Air baffle, DIMM 610857-001 Mandatory 3 1U tray for 165z system 4 PCIe x16 riser card bracket 5 PCIe x4 storage card cage 6 Top cover Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service.
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog. 3 Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes. 3 Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is.
Illustrated parts catalog 19
System components Item Description Spare Part Number Customer Self Repair 1 System fan 576898-001 Mandatory 2 PCIe x4 riser card 3 Processors, OpteronAMD Opteron AMD Opteron 6164HE 12c 1.7 Ghz 598730-001 Optional AMD Opteron 6124HE 8c 1.8Ghz 55W 602104-001 Optional AMD Opteron 6168 12c 1.9 Ghz 75W 602108-001 Optional AMD Opteron 6128HE 8c 2.0Ghz 55W 583751-001 Optional AMD Opteron 6136 8c 2.4 Ghz 75W 583753-001 Optional AMD Opteron 6172 12c 2.
Item Description Spare Part Number Customer Self Repair DIMM,2GB PC3-10600R,128Mx8,RoHS 595094-001 Mandatory DIMM,4GB PC3-10600R,256Mx4,RoHS 595095-001 Mandatory DIMM,4GB PC3-10600R,512Mx4,RoHS 595096-001 Mandatory DIMM,8GB PC3-10600R,512Mx4,RoHS 595097-001 Mandatory DIMM,16GB PC3-8500R,512Mx4,RoHS 595098-001 Mandatory DIMM,4GB PC3L-8500R,256Mx8,RoHS 595099-001 Mandatory DIMM,8GB PC3L-8500R,512Mx4,RoHS 595100-001 Mandatory DIMM,2GB PC3-10600E,128Mx8,RoHS 595101-001 Mandatory DIMM,
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit. 2 No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation.
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product. 2 No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant.
HP contact information For the name of the nearest HP authorized reseller: • • • In the United States, call 1-800-345-1518. In Canada, call 1-800-263-5868. In other locations, refer to the HP website at http://www.hp.com/. For HP technical support: • In North America: ○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a week. For continuous quality improvement, calls may be recorded or monitored.
Removal and replacement procedures This chapter provides subassembly/module-level removal and replacement procedures for the HP ProLiant SL165z G7 server. Review the specifications of a new component before installing it to make sure it is compatible with the server. When you integrate new components into the system, record its model and serial number, and any other pertinent information for future reference.
Pre-installation procedure Perform the steps below before you open the server or before you remove or replace any component. WARNING: Failure to properly turn off the server before you open the server or before your start installing/ removing components may cause serious damage as well as bodily harm. 1. Turn off the server and all the peripherals connected to it. 2.
CAUTION: The following rack-mount instructions shall be paid attention to. • Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
These symbols, on power supplies or systems, indicate that the equipment is supplied by multiple sources of power. WARNING: To reduce the risk of injury from electric shock, remove all power cords to completely disconnect power from the system. Powering down the server The server does not completely power down when the power button on the front panel is pressed. The button toggles between On and Standby.
Figure 1 Removing the Top Cover To reinstall the top cover: 1. Align the top cover to the chassis and then slide it towards the front panel to position it into place. 2. Once the top cover is attached to the chassis, tighten the two rear screws to secure the top cover to the chassis.
Cable management Always follow good cable management practices when working inside the computer. • • Keep cables away from major heat sources like the heat sink. • • Keep cables clear of sliding or moveable parts to prevent cutting or crimping. • • • • • Some flat ribbon cables come pre-folded. Never change the folds on these cables. Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not designed to withstand excessive pressure.
Cable connections The following table provides information about personality board cable connector labels. Table 1 Cable Connections from the Personality Board Cable To Cable Designator 6-pin system fan connector 1 System fan 1 J6 6-pin system fan connector 2 System fan 2 J8 6-pin system fan connector 3 System fan 3 J10 6-pin system fan connector 4 System fan 4 J11 The following table provides information about power board cable connector labels.
Table 3 Cable Connections from the System Board Cable To System board designator 4-pin power connector Power board J54 ODD 1 HDD 1 J23 ODD 2 HDD 2 J20 Hard drives One server tray can accommodate two 3.5 in. or four 2.5 in. hard drives, and the chassis can accommodate two server trays for up to four 3.5 in. or eight 2.5 in. hard drives. The server supports both SAS and SATA hard drives.
Figure 5 Removing the Hard Drive Assembly WARNING: Ensure that the system is powered off and all power sources have been disconnected from the server. Voltages are present at various locations within the server whenever an AC power source is connected. This voltage is present even when the main power switch is in the off position. To install the hard drive: 1. Unlock the HDD carrier latches. 2. Rotate the HDD carrier handle up. 3.
Figure 6 Installing the Hard Drive Assembly System board configuration Processor HP ProLiant SL165z G7 Server supports AMD 8-core/12-core G34-Opteron processors. If a single processor is installed, then use socket 1. When two processors are used, the server supports boot functions through the processor installed in socket 1. However, if processor 1 fails, the system cannot boot up, and if processor 2 fails, the system will be automatically booted from processor 1 and provide a processor failure message.
Figure 7 Processor Locations Item Description 1 Processor 1 2 Processor 2 WARNING: To reduce the risk of personal injury from hot surfaces, allow the heat sink and the processor to cool before touching them. NOTE: Before installing the processor, remove the air baffle. To remove the air baffle: 1. Gently rock the air baffle 1 up, and then take it out from the system board. 2.
To remove the heat sink: 1. Loosen the two spring-loaded screws. 2. Lift the heat sink away from the system board. CAUTION: Place heat sink down in an upright position with the thermal patch facing upward. Do not let the thermal patch touch the work surface.
Figure 10 Picking up the Processor from the Socket with the Installation Tool 5. Remove the processor with the installation tool. Figure 11 Removing the Processor NOTE: If the processor installation tool is not included, grasp the processor by its edges and lift it out of the socket. CAUTION: The pins of the socket are very fragile. Do not bend or damage them. CAUTION: Place the processor on a static-dissipating work surface or in an anti-static bag.
To apply the thermal grease compound: 1. Use the alcohol pads provided in spare part kit or a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and on the new processor. Wipe the contact surfaces several times to make sure that no particles or dust contaminants are evident. 2. Apply the thermal grease compound to the integrated heat spreader on the processor in one of the following patterns to insure even distribution.
To install the new processor: 1. Squeeze the push fingers of the processor installation tool. 2. Align the tool on the processor; release the push fingers and hold the processor. Figure 13 Picking up the Processor with the Installation Tool 3. Insert the processor into the socket. Figure 14 Aligning and Inserting the Processor 4. Squeeze the push fingers of the processor installation tool to release the processor. 5. Remove the processor installation tool. 6. Engage the retention plate. 7.
Figure 15 Installing the Processor NOTE: If the processor installation tool is not included, grasp the processor by its edges and install it into the socket. CAUTION: With the load lever and the retention plate disengaged, hold the processor by its edges and align it over the empty processor socket. Make sure that you properly align the processor with the orientation notch on the socket.
To install the heat sink: 1. Properly align the heat sink spring-loaded screws to the system board mounting holes. 2. Tighten the spring-loaded screws clockwise to secure the heat sink connection to the system board. Figure 16 Installing the Heat Sink Assembly CAUTION: When installing two heat sinks, please put the heat sinks with the 15-fin side facing the DIMMs. CAUTION: For proper cooling, do not operate the server without the top cover, air baffle, expansion slot covers, or blanks installed.
To install the air baffle: 1. Connect all necessary cables. 2. Gently place the air baffle 1 on the system board. 3. Align the screw on the air baffle 2 to the hole on the side of chassis, tighten the screw, and then rotate the other side of the air baffle 2 down.
Memory Each system board has twenty-four DIMM slots that support up to 192 GB maximum system memory (8 GB in each of the twenty-four DIMM slots). You must adhere to the following guidelines when adding or replacing memory modules: • • • For 2P system, both physical processors must be of the same type and speed. Use DDR3 RDIMM/UDIMM. Support single-rank, dual-rank, and quad-rank DIMM.
Figure 19 DIMM Slots To remove memory module: 1. Completely open the holding clips securing the memory module. 2. Gently pull the memory module upward to remove it from the slot. Figure 20 Removing a Memory Module CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static bag.
To install a memory module: 1. Align the notch on the bottom edge of the memory module with the keyed surface of the DIMM slot and then fully press the memory module into the slot until the holding clips snap back in place. Figure 21 Installing a Memory Module CAUTION: The DIMM slots are structured to ensure proper installation. If you insert a DIMM but it does not fit easily into the slot, you may have inserted it incorrectly. Reverse the orientation of the DIMM and insert it again.
PCIe expansion card System board PCIe expansion slot There is one PCIe expansion slot on each system board.
PCIe riser card expansion slot The one PCIe riser card attached to the PCIe cage converts the functionality of the system board expansion slot to the slot positioned at a 90° angle from the system board. Figure 23 PCIe x16 Riser Card Connector Location • One slot PCIe riser card (x16 link with x16 slot) To remove the PCIe riser card with the bracket: 1. Loosen the screw securing the riser card bracket to the side of the chassis. 2. Lift the riser card with the bracket out of the system board.
To remove the PCIe x16 riser card from the bracket: 1. Remove the two screws securing the riser card to the bracket. 2. Remove the riser card from the bracket. Figure 25 Removing the PCIe Riser Card from Bracket To install the PCIe x16 riser card to the bracket: 1. Align the screw holes on the riser card to the screw holes on the bracket. 2. Fasten the two screws to secure the riser card to the bracket.
To install the riser card with the bracket into the system board: 1. Align the riser card connector to the system board expansion slot and then press the riser card assembly down to ensure full connection to the system board. 2. Fasten the screw to secure the bracket to the side of the chassis. Figure 27 Installing the PCIe Riser Card with Bracket To remove the PCIe expansion board: 1. Remove the screw that secures the PCIe expansion board. 2. Press the PCIe expansion board latch spring. 3.
To install the PCIe expansion board: 1. Press the PCIe expansion board latch spring. 2. Slide the PCIe expansion board bracket across the chassis. 3. Insert the PCIe expansion board into the slot on the PCIe riser card. 4. Install and fasten the screw. 5. Close the PCIe expansion board latch.
Storage card System board storage card slot There is one storage card slot on each system board.
PCIe riser card expansion slot The PCIe riser card attached to the storage card cage converts the functionality of the system board expansion slot to the slot positioned at a 90° angle from the system board. Figure 31 PCIe x4 Riser Card Connector Location • One slot PCIe riser card (x4 link with x8 slot) Storage card cage To remove the storage card cage: NOTE: Disconnect all cables connecting an existing expansion board to the system board. 1.
Installing PCIe riser card To remove the PCIe riser card: 1. Loosen the two screws securing the riser card to the storage card cage. 2. Remove the riser card from the storage card cage. Figure 33 Removing the PCIe x4 Riser Card To install the PCIe riser card: 1. Align the screw holes on the riser card to the screw holes on the storage card cage. 2. Install and tighten the two screws that secure the riser card to the storage card cage.
To reinstall the storage card cage: 1. Align the storage card cage to the system board storage card slot, and then press it down to ensure full connection to the system board. 2. Tighten the two screws to secure the storage card cage to the server. Figure 35 Reinstalling the Storage Card Cage 3. Connect the necessary cable(s) to the system board. Mgmt card (Optional) Each system board can support one mgmt card. The mgmt card is optional for the shipment.
To remove the mgmt card: 1. Loosen the screw on the mgmt card. 2. Remove the mgmt card from the mgmt card connector. Figure 37 Removing the Mgmt Card To reinstall the mgmt card: 1. Remove the mgmt port knock-out. Figure 38 Removing the Mgmt Port Knock-out NOTE: You must use the slotted driver to remove the knock-out. 2. Insert the mgmt card into the mgmt card connector on the system board. 3. Tighten the screw clockwise to secure the mgmt card to the system board.
Figure 39 Reinstalling the Mgmt Card SD reader module (Optional) Each system board can support one SD reader module. The SD reader module is optional for the shipment. The following figure shows the SD reader module location.
To remove the SD reader module: 1. Disconnect the SD reader module USB cable from USB connectors on the SD reader module and the system board. Figure 41 Disconnecting the SD Reader Module USB Cable 2. Loosen the screw that secures the SD reader module to the server and then remove the SD reader module.
To reinstall the SD reader module: 1. Remove the SD reader module knock-out from the front panel of the server. Figure 43 Removing the SD Reader Module Knock-out NOTE: You must use the slotted driver to remove the knock-out. 2. Align the SD reader module to the front panel, and tighten the screw that secures the SD reader module to the server.
3. Connect the SD reader module USB cable from USB connectors on the SD reader module and the system board. Figure 45 Connecting the SD Reader Module USB Cable System battery The server uses nonvolatile memory that requires two batteries to retain system information when power is removed. This 3 V lithium coin cell battery is located on the system board.
instructions. CAUTION: Loss of BIOS settings occurs when the battery is removed. You must reconfigure BIOS settings whenever you replace the battery. NOTE: If the server no longer automatically displays the correct date and time, you may need to replace the system battery. Under normal usage, battery life is five to ten years. To replace the system battery: 1. Power down the server. 2. Disconnect the power cord(s). 3.
BBWC (Optional) Each system board can support one BBWC. The BBWC is optional for the shipment. The following figure shows the BBWC location. Figure 48 BBWC Location To remove the BBWC: 1. Loosen the screw that secures the BBWC assembly to the server tray, and then remove the BBWC assembly away from the server tray.
2. Pull the BBWC retaining latch. 3. Slide the BBWC back, up and out of the tray. Figure 50 Removing the BBWC To reinstall the BBWC: 1. Pull the BBWC retaining latch. 2. At the same time, align the locking tabs on the BBWC to their holes on the tray. Press the BBWC into the tray, and then push it along the direction of the arrow to lock the locking tabs.
3. Align the hole on the BBWC assembly to its corresponding hole on the server tray. 4. Meanwhile, fasten the screw that secures the BBWC assembly to the server tray. Figure 52 Reinstalling the BBWC Assembly System board removal and replacement procedure To remove the system board: Remove the tray with the system board: 1. Press the tray latch to release the tray handle. 2. Rotate the tray handle to disengage the power connector. 3. Pull the tray assembly out of the chassis.
Remove the system board from the tray: 1. Loosen the nine screws that secure the system board to the tray. 2. Slide the system board back, up and out of the tray. Remove the system board from the tray. Figure 54 Removing the System Board from the Tray To reinstall the system board: 1. Align the system board I/O connectors to their openings and slide the system board into place. The nine screw holes on the tray should align with the system board. 2.
To reinstall the tray with system board: 1. Slide the tray assembly into the tray bay until it stops. 2. Rotate the tray handle until the tray latch catches. Figure 56 Reinstalling the Tray with System Board Power board The following figure shows the top side of the power board.
Item Description 5 16-pin power connector 6 SATA power connector 7 SATA power connector 8 4-pin power connector 9 24-pin power connector The following figure shows the power board location.
To remove the power board: 1. Loosen the four screws that secure the power board to the server tray. 2. Push the power board forward, up and out of the server tray. Figure 59 Removing the Power Board To reinstall the power board: 1. Align the four holes on the power board to their corresponding holes on the server tray, and then push the power board along the direction of the arrow. 2. Fasten the four screws that secure the power board to the server tray.
Power supply unit (PSU) Located on the rear panel of the server power supply is a standard auto ranging 750 W or 1200 W PSU with PFC (power factor correction) function. Figure 61 Power Supply Unit WARNING: Take note of the following reminders to reduce the risk of personal injury from electric shock hazards and/or damage to the equipment.
To remove the power supply: 1. Press the red colored handle. 2. Slide the power supply out of the power supply cage. Figure 62 Removing the Power Supply To reinstall the power supply: 1. Remove the power supply blank from the power supply cage.
2. Slide the power supply into the power supply bay until it snaps into place. Figure 64 Reinstalling the Power Supply System fan The server can support either three or four system fans located at the system fan cage of the chassis rear. System fan 1 is optional. The figure below identifies the system fans by their device number and shows their corresponding cable connections.
Device number Connector System fan 4 J11 on the personality board A new system fan can be installed to allow the server to operate properly in case a default system fan becomes defective. To remove the system fan: 1. Power down the server. 2. Disconnect the power cord(s). 3. Unlock the server if necessary and remove the top cover as described in the section System cover. 4. Disconnect the system fan cable from its corresponding board connector. 5.
To reinstall the system fan: 1. Hold the system fan and press it into the system fan bracket. 2. Connect the system fan cable to its corresponding board connector.
Connectors, switches, and LEDs This chapter contains illustrations and tables identifying and describing the connectors, switches, jumpers, buttons, and LED indicators located on the front panel, rear panel, and system board of the HP ProLiant SL165z G7 server. Connectors and components Front panel components Figure 68 Front Panel Components Item Description 1 Tray handle 2 Tray latch 3 SD reader port (optional) 4 Front panel USB 2.
Item Description 12 Low-profile PCIe expansion card slot cover 13 GbE LAN port for NIC 3 14 Mgmt port (optional) 15 Front UID switch/LED Rear panel components Figure 69 Rear Panel Components Item Description 1 Power supply 2 cable socket 2 Power supply 1 cable socket 3 Rear UID LED Connectors, switches, and LEDs 74
System board components Figure 70 System Board Components Item Designator Description 1 J1 System maintenance jumper 2 J301 PCIe x16 slot 3 CPU1 Processor 1 4 J11 Mgmt card connector 5 J110 DIMM slot 12 for processor 1 6 J103 DIMM slot 1 for processor 1 7 J210 DIMM slot 12 for processor 2 8 J54 4-pin power connector 9 CPU2 Processor 2 10 J52 24-pin power connector 11 J61 Fan connector 1 12 J62 Fan connector 2 13 J203 DIMM slot 1 for processor 2 14 J65 Backplane I
Item Designator Description 21 J100 SAS LED connector 22 J36, J69 Fan connectors 6/7 23 J13 Mini-SAS connector for SATA 24 J55 Power backplane control connector 25 J98 Front panel header 26 J56 TPM connector 27 J78 PCIe x4 slot 28 J23 ODD 1 29 J20 ODD 2 30 BH1 3 V CMOS battery (CR2032) 31 J6 NMI jumper CAUTION: The TPM is not a customer-removable part. Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security rivet.
LED indicators This section contains illustration and descriptions of internal and external status LED indicators located on the: • • • Front panel Rear panel System board These LED indicators aid in problem diagnosis by indicating the status of system components and operations of the server. Front panel LED indicators The front panel LED indicators allow constant monitoring of basic system functions while the server is operating.
Figure 72 Front UID LED Indicator Location Table 6 Front UID LED Indicator Status Components Status Descriptions Front UID LED indicator Steady blue Identification Flashing blue System is being remotely managed Off Off Connectors, switches, and LEDs 78
Figure 73 Power LED Indicator Location Table 7 Power LED Indicator Status Component Status Description Power LED indicator Steady green The server is operating normally Steady amber The server is system off or in hibernation with A/C power Steady red Critical event happens to the server.
The LAN port on the front panel has two LED indicators that allow monitoring of network activity.
Rear panel LED indicator Figure 75 Rear UID LED Indicator Location Table 9 Rear UID LED Indicator Status Components Status Descriptions Rear UID LED indicator Blue Identification Flashing blue System is being remotely managed Off Off Connectors, switches, and LEDs 81
System board LED indicator Each system board contains one LED indicator for use during troubleshooting operations.
Diagnostic tools and setup utilities This chapter provides an overview of the Power-on Self-Test (POST), the POST error messages, and BIOS, SAS and SATA setup utilities. BIOS software The server uses BIOS to boot up the system. BIOS software is a ROM-based firmware that allows reliability, manageability, and connectivity for server platforms. This software contains a set of programs permanently stored in an EEPROM chipset located on the system board.
Navigating through the Setup Utility Use the keys listed in the legend bar on the right of the Setup screen to navigate through the various menu and submenu screens of the Setup Utility. Table 11 lists these legend keys and their respective functions. Table 11 Setup Utility Navigation Keys Key Function ← and → Select different screens. Enter Select items in each menu. Enter, Tab, or Shift-Tab Select a field value or display a submenu screen. Esc Exit the CMOS Setup menu.
Setup Utility menu bar The BIOS Setup Utility provides a menu bar with the menu selections. The menu bar choices are described in the topics below. Main menu Figure 77 Main Menu of BIOS Setup Utility Use this menu to configure the following items: • • • • • • View product name. View processor information and system memory size. Set system time and date. View BIOS build date and version. View system serial number. View NIC#1 MAC addresses.
Advanced menu Figure 78 Advanced Menu of the BIOS Setup Utility WARNING: Incorrect settings may cause the server to malfunction. To correct the settings, press the F9 key to restore the default settings. • • • • • • • • • • • • CPU Configuration—Configure CPU settings. SATA Configuration—Configure IDE settings. Memory Configuration—Configure memory settings. AHCI Configuration—Configure AHCI settings. IPMI Configuration—Configure IPMI 2.0 settings.
Figure 79 IPMI Submenu of the BIOS Setup Utility • • • • • • • • • BMC Firmware Revision—Display the version of the BMC hardware and firmware. BMC/IPMI FW Date—View BMC/IPMI FW date. BMC SDR Version—View BMC SDR version. Set LAN Configuration—Set LAN settings. SEL Configuration—Display BMC event log. Hardware Health Status—Set temperature and fan rotation rate. Watchdog Configuration—Configure watch dog timer status. Serial Port Configuration—Configure serial port connection settings.
Boot menu Figure 80 Boot Menu of the BIOS Setup Utility • • Boot Settings Configuration—Configure settings during system boot. • USB Drive Boot Priority—Configure priority settings for USB devices. Users can configure the BIOS to avoid attempting to boot non-bootable USB devices that are left plugged into the server during POST. The options are High (default) and Low. Boot Device Priority—Use this screen to specify the order in which the system checks for a boot device.
Security menu Figure 81 Security Menu of the BIOS Setup Utility Use this menu to configure the following items: • • • • Supervisor Password—Indicate if a supervisor password has been installed to the system. User Password—Indicate if a user password has been installed to the system. Change Supervisor Password—Modify or change your supervisor password. Change User Password—Modify or change the user password.
Exit menu Figure 82 Exit Menu of the BIOS Setup Utility Use this menu to save changes or discard changes. When you save and exit, the server reboots. • • Save Changes and Exit—Save the changes you have made and exit the BIOS Setup Utility. • Discard Changes—Discard (cancel) any changes you have made. F10 can be used for this operation. You will remain in the Setup Utility. • Restore Default Settings—Load optimal default values for all the setup questions.
These diagnostics, which reside in the BIOS ROM, isolate server-related logic failures and indicate the board or component that needs to be replaced, as indicated by the error messages. Most server hardware failures are accurately isolated during POST. The number of tests displayed depends on the configuration of the server. During POST you can: • Press F10 to access the Setup Utility. POST error indicators When POST detects a system failure, it displays a POST error message.
Physical and operating specifications This chapter provides physical and operating specifications for the HP ProLiant SL165z G7 server.
Table 12 Hardware Specifications Item Components Power Supply unit (PSU) 750 W or 1200 W redundant, power supply Thermal solution Four system fans Table 13 Physical Dimensions Item Description System board platform EATX (Extended Advanced Technology Extended) System board dimension 12” x 13” (304.8 mm x 330.2 mm) Server dimensions Rack 448W x 87.9H x 714.
Table 15 Power Supply Specifications Item Description Input requirements: Rated input voltage 90 VAC to 264 VAC Normal line voltage 100 VAC to 120 VAC / 200 VAC to 240 VAC Line frequency 50Hz – 60Hz Rated input current Max: 10A BTU rating N/A Power supply output power: Rated steady state power Maximum peak power 750 W N/A Temperature range: Operating Storage/Shipping +5°C to +50°C –40°C to +85°C Relative humidity: Operating Non-operating 5% to 95% relative humidity, non-condensing.
Index A H AC power hard drive power-down procedures, 28 air baffle installing, 42 removing, 35 installing, 33 removing, 32 hardware configuration BBWC, 61 hard drives, 32 B battery replacement warnings, 59 BBWC reinstalling, 62 removing, 61 BIOS Setup Utility accessing, 83 additional navigation keys, 84 menu bar, 83 BIOS software Overview, 83 C cable management, 30 CSR (customer self repair), 5 customer self repair (CSR), 5 D memory, 43 mgmt card, 54 PCIe expansion card, 46 Power board, 65 power su
hot surface power supply symbol, 27 reinstalling, 69 warning, 26 removing, 69 HP authorized reseller, 24 power supply unit.
reinstalling, 64 T removing, 63 thermal solution, 93 system cover top cover top cover, 28 reinstalling, 29 system fan reinstalling, 72 removing, 28 Top cover removing, 71 System fan spare part number, 16 Tray with system board spare part number, 20 reinstalling, 65 system LEDs.
