Hardware Reference Guide HP ProOne 600 G1 All-in-One
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Windows is either a trademark or registered trademark of Microsoft Corporation in the United States and/or other countries. Intel and Core are trademarks of Intel Corporation in the U.S. and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product features ............................................................................................................... 1 Overview ................................................................................................................................ 1 Front components ..................................................................................................................... 3 Side components ...................................................................
Connecting a second display ................................................................................................... 24 Locating internal components ................................................................................................... 27 Removing and installing memory .............................................................................................. 28 SODIMMs ..............................................................................................................
1 Product features Overview Figure 1-1 HP ProOne 600 G1 All-in-One The HP ProOne 600 G1 All-in-One offers the following features: ● Integrated All-in-One form factor ● Full HD IPS, LCD display (1920 x 1080) with LED backlighting ◦ 54.6-cm (21.
2 ● Optional Tray-load HP SuperMulti DVD+/-RW SATA Optical Disc Drive, DVD-ROM Disc Drive, or Slim BDXL Blu-ray Writer ● Intel Q85 Express chipset ● Two SODIMM slots with up to 16 GB of DDR3 SDRAM memory and dual channel memory support ● Intel integrated graphics ● DisplayPort video out (with audio) for second display support ● Optional MXM graphics card ● DP audio, DP to VGA/DVI/HDMI dongle support ● Integrated Gigabit Ethernet (Intel i217LM GbE LOM) ● Wireless connectivity (optional): ◦
Front components Figure 1-2 Front components Table 1-1 Front components Component Component 1 Webcam (optional) with privacy shutter 7 Mute speaker 2 Dual microphone array (optional) 8 Reduce volume 3 Webcam activity LED (with optional webcam) 9 Increase volume 4 16:9 widescreen LED-backlit LCD display 10 Mute microphone 5 Power LED 11 Decrease brightness 6 High-performance stereo speakers 12 Increase brightness Touch the icon area (7–12 above) to cause the icons to illuminate, th
Side components Figure 1-3 Side components Table 1-2 Side components 4 Component Component 1 Hard disc drive activity LED 6 Headset/line out jack 2 HP 6-in-1 media card reader (optional) 7 Tray-load optical disc drive 3 USB 3.0 port, fast-charging 8 Optical disc drive eject button 4 USB 3.
Rear components Figure 1-4 Rear components Table 1-3 Rear components Component Component 1 Access panel 7 RJ-45 Gigabit Ethernet port 2 Access panel latches 8 (2) USB 3.0 ports 3 Security lock slot 9 DisplayPort connector 4 Power connector 10 Stereo audio line out 5 (2) PS/2 mouse and keyboard connectors 11 Access panel security screw 6 (2) USB 2.
Keyboard features Figure 1-5 Keyboard features Table 1-4 Keyboard features 6 Component Component 1 Sleep 6 Mute Volume 2 Fast Reverse 7 Decrease Volume 3 Play/Pause 8 Increase Volume 4 Stop 9 Function 5 Fast Forward Chapter 1 Product features
Positioning the computer This computer may be shipped with no stand, with a height-adjustable stand, or a tilt/swivel stand. The computer may be placed in the landscape position with the HP logo on the bottom bezel or it may be placed in the portrait position with the HP logo on the right side, as you face the computer. Figure 1-6 Supported and unsupported positions CAUTION: Positioning the computer with the HP logo on the top or on the left is not supported.
WARNING! If the height-adjustable/recline stand is installed, before laying the computer down for service, first grasp the sides of the display and raise the display to the highest position. Do not lay the computer down with the sliding stand in the low position. The stand may suddenly release, which could cause injury or damage to equipment.
Figure 1-10 Adjusting swivel Positioning the computer 9
2 Hardware repair and upgrade Warnings and cautions Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide. WARNING! To reduce the risk of personal injury from electrical shock, hot surfaces, or fire: Disconnect the power cord from the wall outlet and allow the internal system components to cool before touching. Do not plug telecommunications or telephone connectors into the network interface controller (NIC) receptacles.
CAUTION: Static electricity can damage the electrical components of the computer or optional equipment. Before beginning these procedures, be sure that you are discharged of static electricity by briefly touching a grounded metal object. See Electrostatic discharge on page 49 for more information. When the computer is plugged into an AC power source, voltage is always applied to the system board.
6. If the tilt/swivel stand is installed on the computer, attach the cable management cover: a. Position the cable management cover under the cables and align the cover hooks with the slots in the stand. b. insert the cover hooks into the stand and slide the cover down to secure it. Figure 2-2 Installing the cable management cover 7. Replace the rear port cover. 8. Press the power button on the front of the computer to turn it on. Disconnecting power 12 1.
Installing and removing the rear port cover Installing the rear port cover 1. Be sure that all cables are connected. 2. Place the cover against the computer, lining up the cable lock slot in the cover about 12 mm (0.5 inch) below the cable lock slot in the computer. Slide the cover up and into position. Figure 2-3 Installing the rear port cover Removing the rear port cover 1. If a cable lock is installed on the rear of the unit, remove the lock. 2.
Installing a security lock The optional security lock enables you to secure your computer. A cable lock is a key lock device that has a wire cable attached. You attach one end of the cable to your desk (or other stationary object) and the other end of the cable to the cable lock slot on the computer. Secure the cable lock with the key. Figure 2-5 Installing a cable lock Installing an access panel security screw You may prevent access to internal components by securing the access panel.
Synchronizing the optional wireless keyboard and mouse The optional wireless keyboard and mouse are easy to set up. Just remove the battery tabs on both the keyboard and the mouse to activate the preinstalled batteries. Also, make sure the Power switch on the bottom of the mouse is in the On position (the keyboard does not have a Power switch). Then, turn on the computer and synchronize them as described below.
Removing batteries from the optional wireless keyboard or mouse NOTE: The wireless keyboard and mouse are optional components. To remove batteries from the wireless keyboard, remove the battery door on the underside of the keyboard (1) and lift the batteries out of the battery compartment (2).
Attaching the computer to a mounting fixture You can remove the computer from the stand and install it on a wall, monitor arm, or other mounting fixture. There is a VESA mount under the computer stand that is used for mounting the computer. Table 2-1 Computer dimensions (without stand) Computer dimensions (without stand) Height 367.4 mm 14.5 in Width 521.9 mm 20.5 in Depth 63.8 mm 2.5 in Minimum configuration 6.63 kg 14.6 lb With Options 7.88 kg 17.4 lb 100 mm x 100 mm 3.94 in x 3.
Installing and removing a stand Two stands are available for the computer: ● Height-adjustable/recline stand ● Tilt/swivel stand Installing and removing a height-adjustable/recline stand (optional) Installing a height-adjustable/recline stand To install the stand: 1. Place the computer face down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth to protect the bezel and screen surface from scratches or other damage. 2.
3. Tighten the four captive screws to secure the stand to the chassis. Figure 2-12 Securing the stand Removing a height-adjustable/recline stand To remove the stand: 1. Remove all removable media, such as compact discs or USB flash drives, from the computer. 2. Turn off the computer properly through the operating system, then turn off any external devices. 3. Disconnect the power cord from the power outlet and disconnect any external devices.
5. Place the computer face down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth to protect the bezel and screen surface from scratches or other damage. WARNING! Before laying the computer down for service, first grasp the sides of the display and raise the display to the highest position. Do not lay the computer down with the sliding stand in the low position. The stand may suddenly release, which could cause injury or damage to equipment.
7. Lift the stand up and off the computer. Figure 2-15 Removing the stand Installing and removing a tilt/swivel stand (optional) Installing a tilt/swivel stand To install the stand: 1. Place the computer face down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth to protect the bezel and screen surface from scratches or other damage. 2. Push the release button on the bottom of the stand and pull the back of the stand off. 3.
4. Tighten the captive screws to secure the stand to the chassis. Figure 2-17 Securing the stand 5. Align the top of the back of the stand with the stand, and press it into place, working along the sides until it is in place. Figure 2-18 Installing the back of the stand Removing a tilt/swivel stand To remove the stand: 1. Remove all removable media, such as compact discs or USB flash drives, from the computer. 2.
4. Remove/disengage any security devices that prohibit opening the computer. 5. Place the computer face down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth to protect the bezel and screen surface from scratches or other damage. 6. Push the release button (1) on the bottom of the stand and pull the back of the stand off (2) the computer. Figure 2-19 Removing the back of the stand 7.
8. Lift the stand up and off the computer. Figure 2-21 Removing the stand Connecting a second display The DisplayPort connector on the rear of the computer allows you to connect a second display to the computer. If you are adding a second display that has a DisplayPort connector, then no DisplayPort video adapter is required. If you are adding a second display that does not have a DisplayPort connector, you can purchase a DisplayPort video adaptor from HP for your configuration.
3. If your second display has a DisplayPort connector, connect a DisplayPort cable directly between the DisplayPort connector on the rear of the computer and the DisplayPort connector on the second display.
4. If your second display does not have a DisplayPort connector, connect a DisplayPort video adapter to the DisplayPort connector of the computer. Then connect a cable (VGA, DVI. or HDMI, depending on your application) between the adapter and a second display. NOTE: When a DisplayPort adaptor is used, the rear port cover cannot be installed unless a DisplayPort extender cable is used in conjunction with the adaptor. Figure 2-24 Connecting a second display Using a DisplayPort adapter 5.
Locating internal components The following sections contain procedures for removing and replacing these internal components: ● Memory ● Battery ● Hard disc drive, solid state drive, or self-encrypting drive ● Optical disc drive Figure 2-25 Locating internal components Component Component 1 Optical disc drive 3 Memory 2 Hard disc drive 4 Battery Locating internal components 27
Removing and installing memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) small outline dual inline memory modules (SODIMMs). SODIMMs The memory sockets on the system board can be populated with up to two industry-standard SODIMMs. These memory sockets are populated with at least one preinstalled SODIMM. To achieve the maximum memory support, you can populate the system board with up to 16 GB of memory.
Populating SODIMM sockets The system will automatically operate in single channel mode, dual channel mode, or flex mode, depending on how the SODIMMs are installed. Refer to the following table to identify the SODIMM channel locations. Table 2-2 Identifying SODIMM locations Location System board label Channel Lower Socket SODIMM1 Channel A Upper Socket SODIMM3 Channel B ● The system will operate in single channel mode if the SODIMM sockets are populated in one channel only.
6. Slide the access panel latches toward the edges of the unit, then slide the access panel toward the top of the computer until it slides off the unit. Figure 2-26 Removing the access panel 7. To remove a memory module, press outward on the two latches on each side of the SODIMM (1), then pull the SODIMM out of the socket (2).
8. To install a memory module, slide the SODIMM into the socket at approximately a 30° angle (1), then press the SODIMM down (2) so that the latches lock it in place. Figure 2-28 Installing a memory module NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. 9. To replace the access panel, set the panel on the back of the computer, slightly above the stand, and slide it down into place. Figure 2-29 Replacing the access panel 10.
Replacing the battery The battery is located on the system board on the lower right side of the fan. The battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of fire and burns if the battery is not handled properly.
6. Slide the access panel latches toward the edges of the chassis, then slide the access panel toward the top of the computer until it slides off the chassis. Figure 2-30 Removing the access panel The battery can now be seen on the lower right side of the fan. Figure 2-31 Locating the battery 7. To release the battery from its holder, squeeze the metal clamp that extends above one edge of the battery. When the battery pops up, lift it out (1).
8. To insert the new battery, slide one edge of the replacement battery under the holder’s lip with the positive side up. Push the other edge down until the clamp snaps over the other edge of the battery (2). Figure 2-32 Removing and replacing a coin cell battery 9. To replace the access panel, set the panel on the back of the computer, slightly above the stand, and slide it down into place. Figure 2-33 Replacing the access panel 10. Reconnect the power cord and external devices. 11.
Replacing drives Replacing a hard disc drive The hard disc drive is located behind the access panel on the lower left side of the computer (when viewed from behind). The drive is housed in a removable cage. Any one of the following may be installed in the computer: ● One 3.5-inch hard disc drive ● One 2.5-inch solid state drive (SSD) or self-encrypting drive (SED) ● Two 2.5-inch solid state drives or self-encrypting drives NOTE: Replacing a 3.5-inch drive with a 2.5-inch drive is not supported.
6. Slide the access panel latches toward the edges of the chassis, then slide the access panel toward the top of the computer until it slides off the chassis. Figure 2-34 Removing the access panel 7. Pull the latch next to the lower side of the drive cage away from the cage to release it, then slide the cage toward the edge of the chassis and lift it out.
8. Lift the latch on one side of the drive cage and pull the hard disc drive out of the cage. Figure 2-36 Removing the 3.5-inch hard disc drive from the cage 9. Remove the four mounting screws from the 3.5-inch hard disc drive. Be sure to keep the screws together with the blue rubber grommets to use to install a replacement disc drive. Figure 2-37 Removing the mounting screws For instructions on installing a hard disc drive, see Installing a hard disc drive on page 40. Removing a 2.
5. Place the computer face down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth to protect the bezel and screen surface from scratches or other damage. 6. Slide the access panel latches toward the edges of the chassis, then slide the access panel toward the top of the computer until it slides off the chassis. Figure 2-38 Removing the access panel 7.
9. Slide the drive adapter holding the 2.5-inch drive or drives out of the drive cage. Figure 2-40 Removing the 2.5-inch drive adapter from the drive cage 10. Remove the four mounting screws from the 2.5-inch hard disc drive adapter. Be sure to keep the screws together with the blue rubber grommets to use to install a replacement drive. NOTE: The primary drive is the lower position in the drive cage. If only one drive is to be installed, it must occupy this position.
Installing a hard disc drive ● Installing a 3.5-inch hard disc drive ● Installing 2.5-inch hard disc drives Installing a 3.5-inch hard disc drive 1. Screw the four mounting screws into the 3.5-inch hard disc drive. Be sure to keep the blue rubber grommets behind each screw. Figure 2-42 Inserting the mounting screws 2. With the 3.
3. With the 3.5-inch hard disc drive connector facing toward the center of the chassis, place the hard disc drive cage into the chassis and slide it toward the center until it snaps into place. Figure 2-44 Installing the 3.5-inch hard disc drive cage 4. To replace the access panel, set the panel on the back of the computer, slightly above the stand, and slide it down into place. Figure 2-45 Replacing the access panel 5. Reconnect the power cord and external devices. 6.
Installing 2.5-inch hard disc drives 1. Insert the 2.5-inch hard disc drive or drives into the 2.5-inch disc drive adapter. Be sure that the connectors are at the opening of the adapter. NOTE: The primary drive is the lower position in the drive adapter. If only one drive is to be installed, it must occupy this position. 2. Fasten the four mounting screws with grommets into the sides of the 2.5-inch drive adapter. Figure 2-46 Securing the mounting screws into the 2.
3. Slide the drive adapter holding the 2.5-inch drive or drives into the drive cage. Figure 2-47 inserting the 2.
4. Position the drive cage above its final site with the hard disc drive connectors facing toward the center of the chassis. If the drive cage contains a secondary (upper) drive, connect the SATA cable to the right of the drive cage to the secondary drive. Figure 2-48 Connecting the secondary 2.5-drive 5. Place the drive cage into the chassis and slide it toward the center until it snaps into place.
6. To replace the access panel, set the panel on the back of the computer, slightly above the stand, and slide it down into place. Figure 2-50 Replacing the access panel 7. Reconnect the power cord and external devices. 8. Lock any security devices that were disengaged when the access panel was removed. 9. Place the computer in the upright position. 10. Turn on the computer.
6. Slide the access panel latches toward the edges of the chassis, then slide the access panel toward the top of the computer until it slides off the chassis. Figure 2-51 Removing the access panel 7. Lift the tab at the back of the optical disc drive enclosure to release the drive.
8. Remove the two screws securing the optical disc drive bracket to the drive. Figure 2-53 Removing the optical disc drive bracket 9. Secure the optical disc drive bracket to the new drive with the two screws.
10. Align the new optical disc drive with the opening in the side of the computer. Push the drive in firmly until it snaps into place. NOTE: The optical disc drive can be installed in only one way. Figure 2-55 Installing the optical disc drive 11. To replace the access panel, set the panel on the back of the computer, slightly above the stand, and slide it down into place. Figure 2-56 Replacing the access panel 12. Reconnect the power cord and external devices. 13.
A Electrostatic discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing electrostatic damage To prevent electrostatic damage, observe the following precautions: ● Avoid hand contact by transporting and storing products in static-safe containers.
B Computer operating guidelines, routine care, and shipping preparation Computer operating guidelines and routine care Follow these guidelines to properly set up and care for the computer: 50 ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer to permit the required airflow.
◦ Wipe the screen with a soft, clean antistatic cloth. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol. Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface. Never spray the cleaner directly on the screen surface. It may run behind the bezel and damage the electronics. ◦ Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign matter can block the vents and limit the airflow.
Index A additional information B battery replacement 11 32 C components front 3 internal 27 rear 5 side 4 computer operating guidelines 50 D DisplayPort video adapter, connecting 24 drive 2.5-inch, installing 42 2.5-inch, removing 37 3.5-inch, installing 40 3.5-inch, removing 35 types 35 E electrostatic discharge, preventing damage 49 F features keyboard 6 overview 1 front components 3 G grounding methods 49 52 Index H hard disc drive 2.5-inch 35 2.5-inch, installing 42 2.5-inch, removing 37 3.
security access panel security screw location 14 cable lock slot location 14 shipping preparation 51 side components 4 SODIMM identification 29 location 29 specifications 28 specifications, memory 28 stand height-adjustable/recline, installing 18 height-adjustable/recline, removing 19 tilt/swivel stand, installing 21 tilt/swivel stand, removing 22 swivel adjustment 8 synchronizing wireless keyboard and mouse 15 T tilt adjustment 8 tilt/swivel stand installing 21 removing 22 V ventilation guidelines 50 VESA
