UPS R6000 Models Installation Instructions

ManualsBrandsHP ManualsOtherHP R5000 Uninterruptible Power Systems

hp uninterruptible

power system R6000

models

installation instructions

Read instructions completely before beginning

installation procedure.

Hewlett-Packard Company shall not be liable for technical or editorial errors or

omissions contained herein. The information in this document is provided “as is”

without warranty of any kind and is subject to change without notice. The warranties

for HP products are set forth in the express limited warranty statements

accompanying such products. Nothing herein should be construed as constituting an

additional warranty.

hp uninterruptible power system R6000 models installation instructions

Second Edition (December 2002)

Part Number 347222-003

347222- 003

About This Device

These instructions show how to install an uninterruptible power

system (UPS). For detailed information about the UPS, refer to the

UPS user guide on the Power Products Documentation CD.

Important Safety Information

Before installing this product, read the Important Safety

Information guide included with the UPS kit.

Regulatory Compliance Identification

Numbers

For regulatory compliance certifications and identification

purposes, the UPS models are assigned a series number, also

identified on the Regulatory Compliance label located on the side

of the UPS. For certification information, always refer to the series

number EO3001.

NOTE: The rating label on the device provides the class (A or B) of the

equipment. Class B devices have a Federal Communications Commission

(FCC) logo or FCC ID on the label. Class A devices do not have an FCC logo

or FCC ID on the label. After you determine the class of the device, refer to

the UPS user guide for complete regulatory compliance notices.

Weight

136 kg

300 lb

WARNING: The UPS weighs 136 kg (300 lb) when fully

assembled. To prevent personal injury or damage to the

equipment:

• Observe local occupational health and safety

requirements and guidelines for manual material

handling.

• Obtain adequate assistance to lift and stabilize the

product during installation or removal. The UPS is

unstable when not fastened to the rails.

• Remove the battery module to reduce the overall

weight of the product.

Position

WARNING: To prevent personal injury or damage to the

equipment, take the following precautions when installing the

equipment:

• The UPS must be installed at the bottom of the rack. If

placed in the rack with existing equipment, the rack must be

reconfigured to allow installation of the UPS at the bottom

of the rack.

• The UPS must be mounted on the rails included in the UPS

kit. Use the rack template tool included in the kit to align

the rails.

Checking the Battery

Recharge Date

Before unpacking the UPS, check the battery recharge date

specified on the battery recharge date label that is affixed to the

shipping carton.

IMPORTANT: Do not use the battery if the recharge date has passed. If the

date on the battery recharge date label has passed without the battery being

recharged, contact an HP authorized service representative for directions.

NOTE: The following label is only an example date. The date on your carton

may be different.

Kit Contents

Documentation

• International Regulatory Compliance guide

• Important Safety Information guide

• Power Products Documentation CD

• Rack and Power Management Pack CD

• This document

Rails

• Rails, with mounting hardware

• Rack template tool 6U (347221-022)

UPS

• UPS chassis (with electronics module)

• Battery modules (2)

• Two front bezel pieces

Additional Hardware

The following items are supplied for shipping a rack with a UPS

installed:

• M6 nuts (4)

• M6 flat washers (4)

• M6 split washers (4)

Cables

• Two 16 A IEC-320 jumpers (242867-001)

• Two 10 A, 2-meter (6-foot) IEC-320 power cords

(142263-001)

• Two 10 A, 2.5-meter (8-foot) IEC-320 power cords

(142263-002)

• Two 10 A, 3-meter (10-foot) IEC-320 power cords

(142263-003)

• 3.66-meter (12-foot) UPS/computer interface cable

(295245-004)

Tools and Materials Required

A #2 Phillips screwdriver is required.

The following items are supplied with the rack:

• Screws

• Cage nuts

• Cage nut-fitting tool

Preparing for Installation

Unpacking the UPS

WARNING: To prevent personal injury or damage to the

equipment:

• Only use the lift-out tray to unload the UPS.

• Do not use the lift-out tray to transport or carry the UPS.

Transport the UPS to its installation location. Unpack the UPS near

the rack where it will be assembled, following the instructions on

the carton. Verify that all components are present.

Mounting the Rails

The UPS must be mounted on the fixed rails supplied with the unit.

Before beginning this installation process, review and adhere to the

following precautions.

WARNING: To prevent personal injury, verify that the rack

containing the UPS is stable. The following conditions must be

met:

• The leveling feet are extended to the floor.

• The full weight of the rack rests on the leveling feet.

• The stabilizing feet are attached to the rack if it is a

single-rack installation.

• The racks are coupled together if it is a multi-rack

installation.

• Only one component should be extended at a time. A rack

may become unstable if more than one component is

extended for any reason.

IMPORTANT: Do not power up the UPS until assembly is complete.

Summary of content (8 pages)

PAGE 1
About This Device hp uninterruptible power system R6000 models installation instructions These instructions show how to install an uninterruptible power system (UPS). For detailed information about the UPS, refer to the UPS user guide on the Power Products Documentation CD. Important Safety Information Checking the Battery Recharge Date Before unpacking the UPS, check the battery recharge date specified on the battery recharge date label that is affixed to the shipping carton.
PAGE 2
About This Device hp uninterruptible power system R6000 models installation instructions These instructions show how to install an uninterruptible power system (UPS). For detailed information about the UPS, refer to the UPS user guide on the Power Products Documentation CD. Important Safety Information Checking the Battery Recharge Date Before unpacking the UPS, check the battery recharge date specified on the battery recharge date label that is affixed to the shipping carton.
PAGE 3
To mount the rails: 1. Loosen the wing nuts (1) and extend the brackets to the desired length (2). Tighten the wing nuts slightly to stabilize the bracket. 4. Insert the screws supplied in the UPS kit through each rack-mounting rail and into the front of each rack. 5. Attach the chassis to the rack using the screws and the cage nuts supplied with the rack. NOTE: After installing the UPS chassis, insert additional screws for support if any screw holes are unoccupied.
PAGE 4
To mount the rails: 1. Loosen the wing nuts (1) and extend the brackets to the desired length (2). Tighten the wing nuts slightly to stabilize the bracket. 4. Insert the screws supplied in the UPS kit through each rack-mounting rail and into the front of each rack. 5. Attach the chassis to the rack using the screws and the cage nuts supplied with the rack. NOTE: After installing the UPS chassis, insert additional screws for support if any screw holes are unoccupied.
PAGE 5
Requirements The UPS requires a dedicated branch circuit meeting the following requirements: • 40 A circuit with overcurrent protection • An appropriate and readily accessible disconnect device incorporated in the fixed wiring • 200-240 V • Single phase • 50-60 Hz NOTE: For ease of service and maintenance, use flexible metal conduit when hardwiring the UPS. Consult a licensed electrician to perform this procedure. 7. Following the diagram on the input terminal block cover: a.
PAGE 6
Requirements The UPS requires a dedicated branch circuit meeting the following requirements: • 40 A circuit with overcurrent protection • An appropriate and readily accessible disconnect device incorporated in the fixed wiring • 200-240 V • Single phase • 50-60 Hz NOTE: For ease of service and maintenance, use flexible metal conduit when hardwiring the UPS. Consult a licensed electrician to perform this procedure. 7. Following the diagram on the input terminal block cover: a.
PAGE 7
4. Turn on the battery circuit breaker. Connecting the Communications Port Charging the Batteries The UPS includes a communications port that allows the unit to exchange data with the host computer. With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: Power management software requires the communications port to be appropriately cabled to the host computer.
PAGE 8
4. Turn on the battery circuit breaker. Connecting the Communications Port Charging the Batteries The UPS includes a communications port that allows the unit to exchange data with the host computer. With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: Power management software requires the communications port to be appropriately cabled to the host computer.