HP SAS Host Bus Adapter Support Matrix
3
HP-UX
After you view the table to determine the correct product configuration, check the driver release notes for your driver version to see if any patches are required.
To access Release Notes, go to: http://docs.hp.com under I/O Cards and Networking Software.
To access patches and download HP Integrity system firmware, go to: http://software.hp.com or http://itrc.hp.com
Select patch database, and search for the patch number. If not already registered, you can register for free on the ITRC home page.
2
Provided the server slot also supports OLAR or OL*.
1
HP recommends adapters in Superdomes be installed or replaced by a field service representative only.
NOTES:
Select
patch
database
,
and
search
for
the
patch
number
.
If
not
already
registered
,
you
can
register
for
free
on
the
ITRC
home
page
.
The HP-UX drivers for the products shown in this matrix are distributed on HP-UX server and workstation Release Media and are installed with an Operating Environment. However, some of the products and drivers listed may be newer
than your system’s Operating Environment.
6
Requires the following minimum software versions: SerialSCSI-00 B.11.23.0712, CommonIO B.11.23.0712, Ignite-UX C.7.4.157.
5
Supports up to two (2) small form factor (SFF) SAS hot-plug hard drives.
7
Requires the following minimum software versions: SerialSCSI-00 B.11.31.0712, CommonIO B.11.31.0712, Ignite-UX C.7.4.157.
4
HP recommends that HP-UX 11i v3 users update to the newest available system and adapter firmware.
8
EFIdi i 30305 l i i df b T b i d
11
MSA60 and MSA70 require the MSA IO Module, Option Kit # AG779A, for use with the AH303A. (No Windows or Linux support)
13
HP-UX 11i v3: Ultrium-3 and Ultrium-4 tape drives require SerialSCSI-00 B.11.31.0712 or later; MSL2024, MSL4048, MSL8096, 1/8G2 autoloader, and DAT160 tape drive require SerialSCSI-00 B.11.31.0803 or later.
HP-UX 11i v2: Ultrium-3 and Ultrium-4 tape drives require SerialSCSI-00 B.11.23.0712 or later; MSL2024, MSL4048, MSL8096, 1/8G2 autoloader, and DAT160 tape drive are not supported.
OpenVMS 8 3-1H1 and Linux: All external SAS tape drives supported
9
Only dual-ported A/A disks are supported in MSA enclosures.
10
MSA50 is supported on HP-UX only. (No OpenVMS, Windows or Linux support)
8
EFI driver version 3.03.05 or later is required for boot support. Tape boot is not supported.
12
AH303A requires VMS831H1I_FIBRE_SCSI-V0100 and VMS831H1I_IPB-V0100 patch kits or later.
Le
g
al Notices
Go to http://docs.hp.com under I/O Cards and Networking Software for matrices for other I/O cards and additional I/O card documentation.
Please send your feedback on this document at http://docs.hp.com/en/feedback.html
Detailed information about slots in entry-level Integrity servers can be found at: http://www.docs.hp.com/en/SSM2-EL/slotmatrix.htm
14
Linux only supports tape connect. No support for MSA50, MSA60 or MSA70 with this controller.
OpenVMS
8
.
3
-
1H1
and
Linux:
All
external
SAS
tape
drives
supported
.
Legal
Notices
© 2004-2008 Hewlett-Packard Company, L.P. The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty.
HP shall not be liable for technical or editorial errors or omissions contained herein.
HP-UX® , and Superdome® are registered trademarks of the Hewlett-Packard Corporation.
All other trademarks and registered trademarks are the property of the respective corporations.
HP SAS Host Bus Adapter Support Matrix Page 2 of 2