RAID-01 (ciss) B.11.31.
© Copyright 2010 Hewlett-Packard Development Company, L.P. Legal Notices Hewlett-Packard makes no warranty of any kind with regard to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material. Confidential computer software.
This document provides updated information about the May 2010 release of the RAID-01 bundle for HP-UX 11i v3. Changes since edition 1 • • • Smart Array AM311A and AM312A are added to “Supported controllers” (page 3). Smart Array AM311A and AM312A are added to “Minimum supported RAID-01 (ciss) versions for HP-UX 11i v3, by adapter” (page 4).
1.1 Driver versions Table 3 lists the minimum supported RAID-01 ciss driver version for each Smart Array host bus adapter: Table 3 Minimum supported RAID-01 (ciss) versions for HP-UX 11i v3, by adapter Adapter Minimum driver version A7143A, A9890A, A9891A B.11.31 Smart Array P400 B.11.31.0709.01 Smart Array P410i B.11.31.1005 Smart Array P411 B.11.31.1005 Smart Array P700m B.11.31.0903 Smart Array P800 B.11.31.0712 Smart Array P812 B.11.31.1005 2 New and changed features in this release 2.
For more information about HBA mode, see the AM311A Smart Array P411/256 Controller for HP Integrity Servers Installation Guide at http://www.hp.com/go/hpux-iocards-docs. Click the link for HP-UX 11i v3. Installation guides are listed alphabetically in the “Setup and install — general” section. • Support for HP Smart Array P410i controllers. The RAID-01 bundle now supports the embedded HP Smart Array P410i controllers in HP Integrity BL8X0c i2 servers running HP-UX 11i v3.
Table 5 HP-UX 11i v3 March 2010 fixes — RAID-01 B.11.31.1003 (continued) SR Number Description QXCR1000941269 The sautil utility does not check the battery count when a RAID 6 (ADG) volume is created. QXCR1000963505 The sautil utility cannot clear the disk error and firmware error logs. Table 6 HP-UX 11i v3 September 2009 fixes — RAID-01 B.11.31.0909 SR Number Description QXCR1000921599 Performing a health check of unloaded drivers causes a system panic.
Corrective Action: After replacing a physical disk, run the sautil command with the scan option. 4.2 For SAS (Serial-Attached SCSI) Smart Array controllers • New Smart Array P700m controller installations should be on HP-UX 11i v3 March 2010 release or later. If you are considering a new installation of an HP Smart Array P700m Controller, HP recommends that you configure it on HP-UX 11i v3 March 2010 release or later.
• SAS Storage Enclosure Status display issue in sautil command output. SAS storage enclosures (SES devices) and their status appear in the outputs of sautil /dev/cissX (extensive output) or sautil /dev/cissX -s (shortened output) commands. Devices appear in the SAS/SATA DEVICE SUMMARY section, and in the detailed information provided for each DISK device and SES device in the command output. The status of a SAS SES device is always FAILED.
Corrective Action: Shut down and power off the system, fix the cabling issue, and power on the system. 5 Compatibility and installation requirements This section describes the compatibility information and installation requirements for this release. For specific installation instructions, see the installation guide or support guide for your controller. These documents are listed in the “Related information” section. 5.
7 Software availability in native languages The RAID-01 product is available only in the English language.
