C6388B Desktop C6389A Rack-Ready C6390A Desktop C6391A Rack-Ready C6394B Desktop C6395A Rack-Ready C6396A Desktop C6397A Rack-Ready HP SCSI Disk Drives User Manual English Japanese
HP C6388B HP C6389A HP C6390A HP C6391A HP C6394B HP C6395A HP C6396A HP C6397A User Manual SCSI Disk Drives Desktop & Rack-Ready Models
ii
Warranty HP offers a two-year warranty for models C6388B, C6389A, C6390A, C6391A, C6394B, C6395A, C6396A, and C6397A. 1. HP warrants HP hardware, accessories, and supplies against defects in materials and workmanship for the period specified above. If HP receives notice of such defects during the warranty period, HP will, at its option, either repair or replace products that prove to be defective. Replacement products may be either new or like-new. 2.
9. TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. 10.
Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. © Copyright 1998 Hewlett-Packard Company All rights reserved Publication number C6388-90001 Applicable Products: HP C6388B HP C6389A HP C6390A HP C6391A HP C6394B HP C6395A HP C6396A HP C6397A Safety Considerations Prior to the installation and use of this product, review all safety markings and instructions. ! Instruction Manual Symbol.
Servicing Any servicing, adjustment, maintenance or repair must be performed only by authorized service-trained personnel. Grounding This product provides a protective grounding terminal. There must be an uninterrupted safety ground from the main power source to the product’s input wiring terminals, power cord, or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored.
Regulatory Information USA Federal Communications Commission (FCC) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Europe Declaration of Conformity according to ISO/IEC Guide 22 and EN45014 Manufacturer’s Name: Hewlett-Packard Manufacturer’s Address: 333 Logue Avenue Mountain View, CA 94043 U.S.A.
Japan VCCI Class B ITE English Translation This equipment is in the Class B category information technology equipment based on the rules of Voluntary Control Council for Interference by Information Technology Equipment (VCCI). Although aimed for residential area operation, radio interference may be caused when used near a radio or TV receiver. Read the instructions for correct operation.
x
1. Overview ................................................................................................ 1-1 2. Disk Installation .................................................................................... 2-1 1. Contents of the Kit for Desktop Models ............................................. 2-1 2. Environment ...................................................................................... 2-2 3. Check Your SCSI Cable ..................................................................
1 ENGLISH Overview HP Desktop Disk Drive HP’s Desktop and Rack-Ready Disk Drives provide a wide range of storage flexibility and reliability: • HP offers a boot capable disk storage solution beginning with the HP C6388B Desktop 4GB drive to the HP C6396A Desktop 9GB disk drive. • When space is at a premium, all desktop versions can be vertically mounted and ship with a vertical mount stand.
1-2 Overview
2 ENGLISH Disk Installation 1.
Note HP rack-ready models C6389A, C6391A, C6395A, and C6397A do not require rubber feet or a stand. Rack-Ready Drives The HP C4318B 3U-4Bay Rack Mount Kit allows you to rack mount up to four HP disk drives into a standard HP 19-inch EIA rack. The C4317A 2U 2Bay Rack Mount Kit has a two drive capacity. See the specifications in Appendix B for more details. Note HP desktop models C6388B, C6390A, C6394B, and C6396A are not supported in a rack-ready environment. 2.
5. Set the SCSI ID Selector Switch The SCSI ID selector allows you to set the SCSI ID from 0 to 15. To change the default setting, push the top button to select a lower number and push the bottom button to select a higher number. Note Each SCSI device must be assigned a unique SCSI ID. Before selecting the SCSI ID for this device, confirm which SCSI ID numbers are already in use by internal and external devices. The default for an internal boot disk drive is usually 6.
6. Mount Your Drive Vertically (Optional) Your HP desktop disk drive can be used in a vertical or horizontal position, as shown in Figure 2-3. Always use the supplied stand when using the drive in the vertical position.
If you wish to mount your disk drive in the vertical position, perform the following steps: Figure 2-4 Attaching the Rubber Feet B. Slide the notches in the foot over the pins on the bottom of the stand. Swing up the foot to lock the pieces together. Stand Foot Figure 2-5 Assembling the Stand Disk Installation 2-5 ENGLISH A. Remove the backing from the four rubber feet and install them on the stand.
C. Insert the corner of the disk unit into the rear of the stand, then swing the unit down to lock it into the stand. Figure 2-6 Inserting the Drive into the Stand 7. Connect the SCSI Cable You can connect the disk drive directly to your system or to another external SCSI device that is connected to your system. To connect the disk drive to another external device, see the information about connecting multiple storage devices in your system owner’s guide.
SCSI Label SCSI DIFF SCSI Cable FAST WIDE–DIFF SCSI or SCSI SE WIDE–SE / NARROW–SE SCSI Figure 2-7 Connecting the SCSI Cable 8. Connect the Power Cable CAUTION To ensure optimal performance, use the 3-wire power cord supplied with this unit. Connect the power cable to the disk drive unit and an AC wall outlet. See Figure 2-8.
9. Power On the Unit Push in the power switch on the front of the unit to ensure that your drive is recognized by your system during boot-up. 10. Configuring the Drive Reference your workstation owner’s guide for instructions about using the HP-UX sam utility to configure your drive. 11. Rack Mounting The Rack-Ready Drives can be mounted into a standard HP 19-inch rack by using the optional HP C4317A (2 EIA units) or the C4318B (3 EIA units) rack mount kits. See Appendix B for more details.
A ENGLISH Specifications Table 1: C6388B Desktop and C6389A Rack-Ready 4GB Wide Single-Ended/Narrow Single-Ended Disk Drive Note Physical Dimensions 62mm(H) x 215mm(W) x 273mm(D) Weight 2.8kg (6.1 lbs) Data Interface Wide SCSI Single-Ended, Dual High-Density 68-pin Boot Disk Exceptions HP 9000 Workstations & Servers: Supported on HP-UX 9.XX – 10.01 as data disks only. For HP-UX 10.10 and above as data or boot disk. Rated A/C Input 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.
Table 2: C6390A Desktop and C6391A Rack-Ready 4GB Fast Wide Differential Disk Drive Note A-2 Specifications Physical Dimensions 62mm(H) x 215mm(W) x 273mm(D) Weight 2.8kg (6.1 lbs) Data Interface Fast Wide SCSI-3 Differential, Dual High-Density 68-pin Boot Disk Exceptions HP 9000 Workstations: Supported on HP-UX 9.XX as data disks only. For HP-UX 10.XX and above as data or boot disk. A/C Input Characteristics 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.
Table 3: C6394B Desktop and C6395A Rack-Ready 9GB Wide Single-Ended/Narrow Single-Ended Disk Drive 62mm(H) x 215mm(W) x 273mm(D) Weight 2.8kg (6.1 lbs) Data Interface Wide SCSI Single-Ended, Dual High-Density 68-pin Boot Disk Exceptions HP 9000 Workstations & Servers: Supported on HP-UX 9.XX – 10.01 as data disks only. For HP-UX 10.10 and above as data or boot disk. A/C Input Characteristics 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.
Table 4: C6396A Desktop and C6397A Rack-Ready 9GB Fast Wide Differential Disk Drive Note A-4 Specifications Physical Dimensions 62mm(H) x 215mm(W) x 273mm(D) Weight 2.8kg (6.1 lbs) Data Interface Fast Wide SCSI Differential, Dual High-Density 68-pin Boot Disk Exceptions Boot capable on all supported operating systems. A/C Input Characteristics 100-240V 50/60Hz. Max 1.2A A/C Current Draw Typical: 0.4 A - 0.2 A Typical Heat Dissipation 22 W, 75 BTU/hr Mechanism Disk Capacity 9.
B ENGLISH Rack-Ready Modules The 3U 4-Bay Rack Kit is designed for mounting into 1.1-meter, 1.6-meter, and 2.0-meter HP 19-inch racks. 1. The HP C4317A (2 EIA units) and C4318B (3 EIA units) are designed for horizontal mounting of four half-height products. 2. These rack enclosures include blind-mate, easy plug connectors providing easy installation and removal of Rack-Ready Modules. See Figure B-1. 3. The HP C4317A (not shown) and HP C4318B rack kits feature Wide 68pin SCSI connectors.
Installation and Removal of Drives Lever in the Closed Position Lever in the Open Position Figure B-2 Ejection Lever Assembly The Rack-Ready Drives are equipped with an ejection lever assembly in place of the rubber feet used on the desktop version. See Figure B-2. The ejection lever assembly is designed for easy installation and removal of drives from the rack mount kit. Note 1. Power down the host system. 2. Open the ejection lever assembly. 3.
C ENGLISH Cable Accessories Cables and Terminators Connection on System Device Type* Cable Pins Cable Length Part Number FWD 68p FWD 68–68 0.9 C2911A FWD 68p FWD 68–68 2.5 C2924A FWD 68p WD WD terminator - C2905A WSE 68p WSE 68–68 0.5m C2978A WSE 68p WSE 68–68 1.5m C2979A WSE 68p WSE SE terminator - C2972A Device to Device in Rack any 68–68 0.5m C2981A NSE 50p WSE 50-68 1.0m C2961A NSE 50p WSE 50-68 1.5m C2962A NSE 50p WSE 50-68 2.
If your drive is the only SCSI device or if it is the last SCSI device in a daisychain of devices, you must install a terminator.
Copyright © 1998 Hewlett-Packard Company Printed in USA 07/98 Manual Part No.
