Fabric OS Documentation Updates Supporting Fabric OS v7.0.x
Table Of Contents
- Contents
- About This Document
- Access Gateway Administrator’s Guide
- CEE Administrator’s Guide
- CEE Command Reference
- Fabric OS Administrator’s Guide
- Documentation updates for Fabric OS v7.0.0 and later
- Chapter 2, Performing Basic Configuration Tasks
- Chapter 4, Routing Traffic
- Chapter 5, Managing User Accounts
- Chapter 6, Configuring Protocols
- Chapter 7, Configuring Security Policies
- Chapter 9, Installing and Maintaining Firmware
- Chapter 12, Traffic Isolation Zoning
- Chapter 18, Administering Licensing
- Chapter 19, Monitoring Fabric Performance
- Chapter 20, Optimizing Fabric Behavior
- Chapter 22, Managing Long Distance Fabrics
- Chapter 23, Using the FC-FC Routing Service
- Documentation updates for Fabric OS v7.0.1 and later
- Documentation updates for Fabric OS v7.0.0 and later
- Fabric OS Command Reference
- Fabric OS Encryption Guide Supporting LKM
- Fabric OS Encryption Guide Supporting RKM
- Fabric OS Encryption Guide Supporting SKM and ESKM
- Fabric OS Encryption Guide Supporting TEMS
- Fabric OS Encryption Guide Supporting TEMS
- Fabric OS FCIP Administrator’s Guide
- Fabric OS FICON Administrator’s Guide
- Fabric OS Message Reference
- Fabric OS MIB Reference
- Fabric OS Troubleshooting and Diagnostics Guide
- Fabric Watch Administrator’s Guide
- Web Tools Administrator’s Guide
- Brocade DCX Backbone Hardware Reference Manual
- Brocade DCX-4S Backbone Hardware Reference Manual
36 Fabric OS Documentation Updates
53-1002165-10
fmMonitor
5
OPERANDS --linkreset slot/blade_port
Performs a link reset on the specified front-end or backend blade port. The blade
port number can be located in the "Bpt" column output of the bladePortMap
command. The bladeportmap command requires root permissions.
fmMonitor
The portlog value for the -action parameter is not supported and has be removed from the man page in
Fabric OS v7.0.2. It should be removed from all printed versions of the v7.0.x Command Reference
manual.
perfHelp
The fmConfig command has been added to the output of the perfHelp command.
serDesTuneMode
This command has been enhanced with new operands to support an automated tuning process to fix
CRC errors. The man page has been updated as follows; only the additions are shown below.
NAME Configures and displays SerDes tuning parameters.
SYNOPSIS serdestunemode --autoenable
serdestunemode --autodisable
serdestunemode --autoreset
serdestunemode --autoshow
DESCRIPTION Use this command to configure and display SerDes values on the Brocade FC8-16 and to control tuning
optimization of backend links for all Brocade FC8-xx blades.
When used with the --autoset, --autodisable, --autoreset and --autoshow options, this command
configures tuning optimization for backend SerDes errors. SerDes tuning optimization is indicated when
you receive RASLog errors of type C2-5825 indicating a CRC error with a good EOF. Brocade highly
recommends that you contact your service provider if you encounter such errors. If the error appears to
be an isolated incident, you may enable auto SerDes tuning for a short period of time (24-48 hours) to
see if this resolves the problem. Then disable the function to reduce the risk of resetting register values
unnecessarily if single occurrence errors are encountered. If the errors persist contact your service
provider.
OPERANDS --autoset Enables SerDes tuning optimization on all backend ports.
--autodisable Disables further tuning optimization but retains all current tuning values identified
by the algorithm.
--autoreset Disables further tuning optimization and resets all tuning values back to their
default values. If SerDes tune mode or was set, the co figuration is restored.
--autoshow Displays whether SerDes tuning optimization is enabled or disabled.