HP Director Blade Installation Instructions Overview Use these installation instructions if you have purchased one of the optional director blades listed in Table 1 (page 1). Install the blades in compatible director models only. NOTE: This document refers to blades by their short names.
HP SAN FC4-48 Director 48-port 4Gb FC blade AG561A 4/256 SAN Director AG561B HP SAN FC4-32 Director 32-port 4Gb FC blade A7991A 4/256 SAN Director A7991B HP SAN FC8-16 Director 16-port 8Gb FC blade AK858A 4/256 SAN Director, AK858B DC SAN Backbone Director, AK858C DC04 SAN Director HP SAN FC8-32 Director 32-port 8Gb FC blade AK859A DC SAN Backbone AK859B Director, DC04 SAN Director AK859C HP SAN FC8-48 Director 48-port 8Gb FC blade AK860A DC SAN Backbone AK860B Director, DC04 SAN Director AK860C H
FC8-48E components FC16-32 components Figure 2 FC8-48E Figure 3 FC16-32 1. Power LED 2. Status LED 3. FC ports 24–47 4. FC ports 0–23 1. Power LED 2. FC ports 8–15 3. FC ports 0–7 4. Port status LED 5. FC ports 24–31 6. Port and trunking group map 7.
FC16-48 components FCOE10-24 components Figure 4 FC16-48 Figure 5 FCOE10-24 1. Power LED 2. FC ports 0–23 3. Status LED 4. FC ports 24–47 Page 4 1. Power LED 2. 10-GbE FCoE ports 0–11 3. Status LED 4.
FX8-24 components FS8-18 components Figure 6 FX8-24 Figure 7 FS8-18 1. Power LED 2. 1 GbE ports 0–3 3. 10-GbE ports 0–1 4. FC ports 0–5 5. Status LED 6. 1 GbE ports 4–9 7. FC ports 6–11 1. Power LED 2. Status LED 3. FC port 4. Port status LED 5.
FC4-16 components FC4-32 components Figure 8 FC4-16 Figure 9 FC4-32 1. Power LED 2. Status LED 1. Power LED 2. Status LED 3. FC Port 4. Port speed LED 3. FC Port 4. Port speed LED (left port) 5. Port status LED 6. FC ports 0–15 5. Port status LED (left port) 6. Port speed LED (right port) 7. Port status LED (right port) 8. FC ports 16–31 9.
FC4-48 components FC8-16 components Figure 10 FC4-48 Figure 11 FC8-16 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. FC ports 0–15 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. FC ports 24–47 6.
FC8-32 components FC8-48 components Figure 12 FC8-32 Figure 13 FC8-48 1. Power LED 2. Status LED 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 3. FC Port 4. Port status LED 5. FC ports 16–31 6. FC ports 0–15 5. FC ports 24–47 6.
FC8-64 components FC10-6 components Figure 14 FC8-64 Figure 15 FC10-6 1. Status LED 2. Power LED 3. FC Port 4. Port status LED 5. FC Port 6. FC Port 7. FC ports 32–63 8. FC ports 0–31 NOTE: only. 1. Power LED 2. Status LED 3. FC port 4. Port status LED 5.
FC4-16IP components FR4-18i components Figure 16 FC4-16IP Figure 17 FR4-18i blade 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. FC ports 0–7 6. GbE ports 0–7 Page 10 1. Power LED 2. Status LED 3. FC Port 4. Port status LED 5. GbE ports 0–1 6.
1. 2. Verifying installation requirements To remove a filler panel with pull tabs: 1. Unscrew the top and bottom captive screws on the filler panel. 2. Grasp the top and bottom pull tabs and remove the filler panel. The installation takes less than 10 minutes.
Blades with ejectors and slider switches 4. The following blades use both ejectors and slider switches: FC4-16 FC4-16IP FC4-32 FR4-18i For blades with both ejectors and slider switches: a. Open the ejectors approximately 45 degrees, align the flat side of the blade inside the upper and lower rail guides in the slot, and then, while applying slight pressure to the left, slide the blade into the slot (Figure 19 (page 12)).
5. For blades with ejectors: a. Open the ejectors. b. Align the flat side of the blade inside the upper and lower rail guides in the slot. c. Slide the blade into the slot until it is firmly seated (Figure 20 (page 13)). d. Close the ejectors.
