Brocade Fabric OS Documentation Addendum - Supporting Fabric OS v5.2.x (53-1000429-01-HP)

1-20 Fabric OS Documentation Addendum
Publication Number: 53-1000429-01-HP
configure Note: Enter commands in lowercase only; mixed case is for readability
1
Examples To modify configuration settings on a switch:
switch:admin> configure
Configure...
Fabric parameters(yes, y, no, n): [no] yes
Domain:(1..239) [1]
R_A_TOV: (4000..120000) [10000]
E_D_TOV: (1000..5000) [2000] 5000
WAN_TOV: (0..30000) [0] 0
MAX_HOPS: (7..19) [7]
Data field size: (256..2112) [2112]
Sequence Level Switching: (0..1) [0] 1
Disable Device Probing: (0..1) [0]
Switch PID Format: (1..2) [1]
Per-frame Route Priority: (0..1) [0]
BB credit: (1..16) [16]
Insistent Domain ID Mode (yes, y, no, n): [no]
Virtual Channel parameters(yes, y, no, n): [no] yes
VC Priority 2: (2..3) [2]
VC Priority 3: (2..3) [2]
VC Priority 4: (2..3) [2]
VC Priority 5: (2..3) [2]
VC Priority 6: (2..3) [3]
VC Priority 7: (2..3) [3]
Switch Operating Mode (yes, y, no, n): [no] yes
Interoperability Mode: (0..1) [0]
Zoning Operation parameters (yes, y, no, n): [no] yes
Disable NodeName Zone Checking: (0..1) [0]
RSCN Transmission Mode (yes, y, no, n): [no] yes
End-device RSCN Transmission Mode
(0 = RSCN with single PID, 1 = RSCN with multiple PIDs, 2 = Fabric RSCN): (0..2) [0]
Arbitrated Loop parameters(yes, y, no, n): [no] yes
Alternate BB credit: (0..1) [0]
Send FAN frames?: (0..1) [1]
Enable CLOSE on OPEN received?: (0..1) [0]
Always send RSCN?: (0..1) [0]
Do Not Allow AL_PA 0x00?: (0..1) [0]
System services(yes, y, no, n): [no] yes
rstatd(on, off): [off]
rusersd(on, off): [off]
telnetd (on, off): [on]
Portlog events enable (yes, y, no, n): [no] yes
start(a switch start or re-start event ) (on, off): [on]
disable(a port is disabled ) (on, off): [on]
enable(a port is enabled ) (on, off): [on]
ioctl(a port I/O control is executed) ) (on, off): [on]
Tx(a frame is transmitted) ) (on, off): [off]
Tx1(a frame is transmitted, class 1 ) (on, off): [on]
Tx2(a frame is transmitted, class 2 ) (on, off): [on]
Tx3(a frame is transmitted, class 3 ) (on, off): [on]
Rx(a frame is received ) (on, off): [on]
Rx1(a frame is received, class 1 ) (on, off): [on]
Rx2(a frame is received, class 2 ) (on, off): [on]
Rx3(a frame is received, class 3 ) (on, off): [on]
stats(port status or statistics ) (on, off): [on]
(continued on next page)