Fabric OS Message Reference v6.4.0 (53-1001767-01, June 2010)
Table Of Contents
- Contents
- About This Document
- Introduction To System Messages
- RASLog Messages
- AG System Messages
- AN System Messages
- AUTH System Messages
- ANV System Messages
- BKSW System Messages
- BL System Messages
- BLL System Messages
- BLS System Messages
- BM System Messages
- C2 System Messages
- CDR System Messages
- CEE CONFIG System Messages
- CER System Messages
- CHASSIS System Messages
- CNM System Messages
- CONF System Messages
- CTAP System Messages
- CVLC System Messages
- CVLM System Messages
- DAUTH System Messages
- EM System Messages
- ESS System Messages
- ESWCH System Messages
- EVMD System Messages
- FABR System Messages
- FABS System Messages
- FBC System Messages
- FCMC System Messages
- FCIP System Messages
- FCOE System Messages
- FCPD System Messages
- FCPH System Messages
- FCR System Messages
- FICON System Messages
- FICU System Messages
- FKLB System Messages
- FLOD System Messages
- FSPF System Messages
- FSS System Messages
- FSSM System Messages
- FW System Messages
- HAM System Messages
- HAMK System Messages
- HIL System Messages
- HLO System Messages
- HMON System Messages
- HSL System Messages
- HTTP System Messages
- IBD System Messages
- IBPD System Messages
- ICPD System Messages
- IPAD System Messages
- IPS System Messages
- ISCS System Messages
- ISNS System Messages
- KAC System Messages
- KSWD System Messages
- KTRC System Messages
- L2SYS System Messages
- LACP System Messages
- LANCE System Messages
- LFM System Messages
- LOG System Messages
- LSDB System Messages
- MFIC System Messages
- MPTH System Messages
- MQ System Messages
- MS System Messages
- MSTP System Messages
- NBFS System Messages
- NS System Messages
- NSM System Messages
- ONM System Messages
- PDM System Messages
- PDTR System Messages
- PLAT System Messages
- PMGR System Messages
- PORT System Messages
- PS System Messages
- PSWP System Messages
- RAS System Messages
- RCS System Messages
- RKD System Messages
- RMOND System Messages
- RPCD System Messages
- RTWR System Messages
- SAS System Messages
- SCN System Messages
- SEC System Messages
- SFLOW System Messages
- SNMP System Messages
- SPC System Messages
- SPM System Messages
- SS System Messages
- SSM System Messages
- SULB System Messages
- SWCH System Messages
- SYSC System Messages
- SYSM System Messages
- TAPE System Messages
- TRCE System Messages
- TRCK System Messages
- TS System Messages
- UCST System Messages
- UPTH System Messages
- WEBD System Messages
- XTUN System Messages
- ZEUS System Messages
- ZOLB System Messages
- ZONE System Messages
- Audit Log Messages
- AUDIT AG System Messages
- AUDIT AN System Messages
- AUDIT AUTH System Messages
- AUDIT BLS System Messages
- AUDIT CNM System Messages
- AUDIT CONF System Messages
- AUDIT CVLM System Messages
- AUDIT FCIP System Messages
- AUDIT FICU System Messages
- AUDIT FW System Messages
- AUDIT HTTP System Messages
- AUDIT IPAD System Messages
- AUDIT PORT System Messages
- AUDIT SEC System Messages
- AUDIT SNMP System Messages
- AUDIT SPM System Messages
- AUDIT SULB System Messages
- AUDIT SWCH System Messages
- AUDIT UCST System Messages
- AUDIT ZONE System Messages
Fabric OS Message Reference 219
53-1001767-01
FCR-1018
34
FCR-1018
Message <timestamp>, [FCR-1018], <sequence-number>,, ERROR, <system-name>, FC router
proxy device entries exhausted on port <port number>.
Probable Cause Indicates that the number of proxy devices is greater than allowed by the port resource.
Recommended
Action
Remove excess logical storage area network (LSAN) zones or devices until the number of proxy
devices exported is within the range allowed by the port resource. Use the fcrResourceShow
command to view resources including LSAN zone resources, LSAN device resources, and proxy
device port resources.
Use the fcrProxyDevShow command to view how many proxy devices are created in the fabric with
the port resource problem.
LSAN zones are removed using standard zoning commands such as zoneShow, zoneRemove,
zoneDelete, cfgDelete, and cfgDisable in the edge fabric. Proxy devices can be removed by zoning
operations or by bringing physical devices offline. For example, disabling the port that a device is
attached to, and then disconnecting the cable or disabling the device.
Severity ERROR
FCR-1019
Message <timestamp>, [FCR-1019], <sequence-number>,, ERROR, <system-name>, EX or VEX port
entries exhausted at port <port number>.
Probable Cause Indicates that the number of EX_Port or VEX_Port entries being created is greater than allowed by
the port resource.
Recommended
Action
EX_Ports or VEX_Ports exceeding the specified range will automatically be disabled by the port
resource. Use the fcrRouteShow command to display the EX_Port or VEX_Port limits. Use the
portDisable command to disable EX_Ports.
Severity ERROR
FCR-1020
Message <timestamp>, [FCR-1020], <sequence-number>,, WARNING, <system-name>, Local LSAN
zone entries for FC router exhausted; max limit: <LSAN zone limit>.
Probable Cause Indicates that the number of logical storage area network (LSAN) zones created within a MetaSAN
exceeds the local LSAN zone database limitations.
Recommended
Action
Remove excess LSAN zones so that the number of LSAN zones created is within the range of local
database limitations.
To do that, perform the following steps:
1. Run the portDisable command to disable all the EX_Ports that got this error message.
2. Run the portDisable command to disable all the other EX_Ports on that FCR connected to the
same edge fabrics the EX_ports disabled in step 1 are connected to.