Fabric OS Message Reference v6.4.0 (53-1001767-01, June 2010)
Table Of Contents
- Contents
- About This Document
- Introduction To System Messages
- RASLog Messages
- AG System Messages
- AN System Messages
- AUTH System Messages
- ANV System Messages
- BKSW System Messages
- BL System Messages
- BLL System Messages
- BLS System Messages
- BM System Messages
- C2 System Messages
- CDR System Messages
- CEE CONFIG System Messages
- CER System Messages
- CHASSIS System Messages
- CNM System Messages
- CONF System Messages
- CTAP System Messages
- CVLC System Messages
- CVLM System Messages
- DAUTH System Messages
- EM System Messages
- ESS System Messages
- ESWCH System Messages
- EVMD System Messages
- FABR System Messages
- FABS System Messages
- FBC System Messages
- FCMC System Messages
- FCIP System Messages
- FCOE System Messages
- FCPD System Messages
- FCPH System Messages
- FCR System Messages
- FICON System Messages
- FICU System Messages
- FKLB System Messages
- FLOD System Messages
- FSPF System Messages
- FSS System Messages
- FSSM System Messages
- FW System Messages
- HAM System Messages
- HAMK System Messages
- HIL System Messages
- HLO System Messages
- HMON System Messages
- HSL System Messages
- HTTP System Messages
- IBD System Messages
- IBPD System Messages
- ICPD System Messages
- IPAD System Messages
- IPS System Messages
- ISCS System Messages
- ISNS System Messages
- KAC System Messages
- KSWD System Messages
- KTRC System Messages
- L2SYS System Messages
- LACP System Messages
- LANCE System Messages
- LFM System Messages
- LOG System Messages
- LSDB System Messages
- MFIC System Messages
- MPTH System Messages
- MQ System Messages
- MS System Messages
- MSTP System Messages
- NBFS System Messages
- NS System Messages
- NSM System Messages
- ONM System Messages
- PDM System Messages
- PDTR System Messages
- PLAT System Messages
- PMGR System Messages
- PORT System Messages
- PS System Messages
- PSWP System Messages
- RAS System Messages
- RCS System Messages
- RKD System Messages
- RMOND System Messages
- RPCD System Messages
- RTWR System Messages
- SAS System Messages
- SCN System Messages
- SEC System Messages
- SFLOW System Messages
- SNMP System Messages
- SPC System Messages
- SPM System Messages
- SS System Messages
- SSM System Messages
- SULB System Messages
- SWCH System Messages
- SYSC System Messages
- SYSM System Messages
- TAPE System Messages
- TRCE System Messages
- TRCK System Messages
- TS System Messages
- UCST System Messages
- UPTH System Messages
- WEBD System Messages
- XTUN System Messages
- ZEUS System Messages
- ZOLB System Messages
- ZONE System Messages
- Audit Log Messages
- AUDIT AG System Messages
- AUDIT AN System Messages
- AUDIT AUTH System Messages
- AUDIT BLS System Messages
- AUDIT CNM System Messages
- AUDIT CONF System Messages
- AUDIT CVLM System Messages
- AUDIT FCIP System Messages
- AUDIT FICU System Messages
- AUDIT FW System Messages
- AUDIT HTTP System Messages
- AUDIT IPAD System Messages
- AUDIT PORT System Messages
- AUDIT SEC System Messages
- AUDIT SNMP System Messages
- AUDIT SPM System Messages
- AUDIT SULB System Messages
- AUDIT SWCH System Messages
- AUDIT UCST System Messages
- AUDIT ZONE System Messages
742 Fabric OS Message Reference
53-1001767-01
SULB-1009
128
"The original firmware has been restored successfully on Standby CP." 0x7e
"Unable to restore the original firmware on Standby CP." 0x7f
"Standby CP reboots." 0x80
"Standby CP failed to reboot." 0x81
"Standby CP booted up with new firmware." 0x82
"Standby CP failed to boot up with new firmware." 0x83
“There was an unexpected reboot during firmwareDownload. The command is aborted.” 0x84
"Standby CP was not responding. The command is aborted." 0x85
“firmwareCommit has started on both CPs. Please use firmwareDownloadStatus and
firmwareShow to see the firmware status.”
0x86
“firmwareCommit has started on the local CP. Please use firmwareDownloadStatus and
firmwareShow to see the firmware status.”
0x87
“firmwareCommit has started on the remote CP. Please use firmwareDownloadStatus and
firmwareShow to see the firmware status.”
0x88
“Please use firmwareDownloadStatus and firmwareShow to see the firmware status.” 0x89
“firmwareDownload command has completed successfully.” 0x8a
"The original firmware has been restored successfully." 0x8b
"Remote CP is restoring its secondary partition." 0x8c
"Local CP is restoring its secondary partition." 0x8d
"Remote CP is restoring its secondary partition." 0x8e
“firmwareDownload has started.” 0x8f
“firmwareCommit has started.” 0x90
“firmwareDownload has completed successfully.” 0x91
“firmwareCommit has completed successfully.” 0x92
“firmwareCommit has started to restore the secondary partition.” 0x93
“firmwareCommit failed.” 0x94
"The secondary partition has been restored successfully." 0x95
"Firmware is being downloaded to the blade. This step may take up to 10 minutes." 0xa0
“firmwareDownload timed out.” 0xa1
“Reboot occurred during firmwareDownload. firmwareCommit will be started to recover the
blade.”
0xa2
“Blade rebooted during firmwareCommit. The operation will be restarted.” 0xa3
"Firmware has been downloaded successfully. Blade is rebooting with the new firmware." 0xa4
"Blade has rebooted successfully." 0xa5
“New firmware failed to boot up. Please retry firmwareDownload.” 0xa6
“firmwareCommit has started on the blade. This may take up to 10 minutes.” 0xa7
TABLE 9 Status Messages and Status Codes
Status Message Status Code