Fabric OS Message Reference v6.4.0 (53-1001767-01, June 2010)
Table Of Contents
- Contents
- About This Document
- Introduction To System Messages
- RASLog Messages
- AG System Messages
- AN System Messages
- AUTH System Messages
- ANV System Messages
- BKSW System Messages
- BL System Messages
- BLL System Messages
- BLS System Messages
- BM System Messages
- C2 System Messages
- CDR System Messages
- CEE CONFIG System Messages
- CER System Messages
- CHASSIS System Messages
- CNM System Messages
- CONF System Messages
- CTAP System Messages
- CVLC System Messages
- CVLM System Messages
- DAUTH System Messages
- EM System Messages
- ESS System Messages
- ESWCH System Messages
- EVMD System Messages
- FABR System Messages
- FABS System Messages
- FBC System Messages
- FCMC System Messages
- FCIP System Messages
- FCOE System Messages
- FCPD System Messages
- FCPH System Messages
- FCR System Messages
- FICON System Messages
- FICU System Messages
- FKLB System Messages
- FLOD System Messages
- FSPF System Messages
- FSS System Messages
- FSSM System Messages
- FW System Messages
- HAM System Messages
- HAMK System Messages
- HIL System Messages
- HLO System Messages
- HMON System Messages
- HSL System Messages
- HTTP System Messages
- IBD System Messages
- IBPD System Messages
- ICPD System Messages
- IPAD System Messages
- IPS System Messages
- ISCS System Messages
- ISNS System Messages
- KAC System Messages
- KSWD System Messages
- KTRC System Messages
- L2SYS System Messages
- LACP System Messages
- LANCE System Messages
- LFM System Messages
- LOG System Messages
- LSDB System Messages
- MFIC System Messages
- MPTH System Messages
- MQ System Messages
- MS System Messages
- MSTP System Messages
- NBFS System Messages
- NS System Messages
- NSM System Messages
- ONM System Messages
- PDM System Messages
- PDTR System Messages
- PLAT System Messages
- PMGR System Messages
- PORT System Messages
- PS System Messages
- PSWP System Messages
- RAS System Messages
- RCS System Messages
- RKD System Messages
- RMOND System Messages
- RPCD System Messages
- RTWR System Messages
- SAS System Messages
- SCN System Messages
- SEC System Messages
- SFLOW System Messages
- SNMP System Messages
- SPC System Messages
- SPM System Messages
- SS System Messages
- SSM System Messages
- SULB System Messages
- SWCH System Messages
- SYSC System Messages
- SYSM System Messages
- TAPE System Messages
- TRCE System Messages
- TRCK System Messages
- TS System Messages
- UCST System Messages
- UPTH System Messages
- WEBD System Messages
- XTUN System Messages
- ZEUS System Messages
- ZOLB System Messages
- ZONE System Messages
- Audit Log Messages
- AUDIT AG System Messages
- AUDIT AN System Messages
- AUDIT AUTH System Messages
- AUDIT BLS System Messages
- AUDIT CNM System Messages
- AUDIT CONF System Messages
- AUDIT CVLM System Messages
- AUDIT FCIP System Messages
- AUDIT FICU System Messages
- AUDIT FW System Messages
- AUDIT HTTP System Messages
- AUDIT IPAD System Messages
- AUDIT PORT System Messages
- AUDIT SEC System Messages
- AUDIT SNMP System Messages
- AUDIT SPM System Messages
- AUDIT SULB System Messages
- AUDIT SWCH System Messages
- AUDIT UCST System Messages
- AUDIT ZONE System Messages
![](/manual/hp/hp-storageworks-director-2-140/fabric-os-message-reference-v640-53-1001767-01-june-2010/images/img-506.png)
748 Fabric OS Message Reference
53-1001767-01
SULB-1024
128
Recommended
Action
The firmwareCommit command will be started automatically after the blade boots up to repair the
secondary partition. If at the end of firmwareCommit, the blade firmware version is still
inconsistent with the active CP firmware, firmwareDownload will automatically be restarted on the
blade. Run the firmwareDownloadStatus command to monitor the progress. If the problem
persists, contact your switch service provider.
Severity WARNING
SULB-1024
Message AUDIT, <timestamp>, [SULB-1024], WARNING, FIRMWARE, <event-initiator-details>,
<event-location>, , Firmware commit has completed on the blade in slot
<Slot
number>.
Probable Cause Indicates the firmwareCommit operation has completed on the specified blade.
Recommended
Action
Run the firmwareShow command to verify the firmware versions. If the blade firmware is the same
as the active CP firmware, firmwareDownload has completed successfully on the blade. However, if
the firmwareCommit operation has been started to repair the secondary partition, at the end of
firmwareCommit, the blade firmware version may still be inconsistent with the active CP firmware.
In that case, firmwareDownload will automatically be restarted on the blade. Run the
firmwareDownloadStatus command to monitor the progress.
Severity WARNING
SULB-1026
Message AUDIT, <timestamp>, [SULB-1026], WARNING, FIRMWARE, <event-initiator-details>,
<event-location>, , Firmware commit operation started on the blade in slot
<Slot
number>
.
Probable Cause Indicates the firmwareCommit command has started on the specified blade. The operation may be
a normal part of firmwareDownload, or it may have started to repair the secondary partition of the
blade if the secondary partition is corrupted.
Recommended
Action
Wait for the commit operation to complete.
Severity WARNING
SULB-1030
Message AUDIT, <timestamp>, [SULB-1030], WARNING, FIRMWARE, <event-initiator-details>,
<event-location>, , The switch has rebooted during relocating the internal
firmware image.
Probable Cause Indicates there may be an error caused by an unexpected disruption of the firmwareDownload
command, for example, by powering the switch off and on in the middle of a firmwareDownload.
The error may also be caused by persistent storage hardware failure or by a software error.