HP StorageWorks Director 2/140 installation guide FW 07.00.00/HAFM SW 08.06.
Legal and notice information © Copyright 2002–2005 Hewlett-Packard Development Company, L.P. © Copyright 2005 McDATA Corp. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents About this guide . . . . . . . . . . . . . . . Contents .................................. 9 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . Document conventions and symbols . . . . . . . . . . . . . . . . . . Rack stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HP technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HP-authorized reseller .
Install the director in a rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack-mount checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Required items. . . . . . . .
R_A_TOV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E_D_TOV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interop mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring preferred path . . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulatory compliance identification numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Laser device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Laser safety warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Mounting anti-tip feet for a HP system/e rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Rail tray mounting location requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Attaching a rear rail tray bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63 64 65 66 67 68 Tables 1 2 3 4 5 6 7 8 9 10 11 8 View All - HAFM 8.6 window . . . . . . . . . . . . . Director Firmware Library dialog box . . . . . . . . New Firmware Version dialog box . . . . . . . . . New Firmware Description dialog box . . . . . . . Backup and Restore Configuration dialog box. . Class 1 laser product label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about installing, configuring, managing, and verifying operation of the HP StorageWorks Director 2/140. The director switch connects storage devices, hosts, and servers in a SAN. The director is easily managed and configured to optimize the performance of your SAN. Intended audience This guide is intended for trained service and installation representatives experienced with the SAN technology and Fibre Channel technology.
Document conventions and symbols Document conventions Table 1 Convention Element Medium blue text: Figure 1 Cross-reference links and e-mail addresses Medium blue, underlined text (http://www.hp.
Rack stability WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. • Install stabilizing feet on the rack. • In multiple-rack installations, secure racks together. • Extend only one rack component at a time. Racks may become unstable if more than one component is extended.
• http://www.hp.com • http://www.hp.com/go/storage • http://www.hp.com/support/ • http://www.docs.hp.
1 Overview This chapter contains the following HP StorageWorks Director 2/140 information: • Director description, page 13 • Features, page 13 • Hardware components, page 17 • Tools and test equipment, page 22 • Optional kits, page 24 Director description The director is a second-generation, 140-port product that provides dynamic switched connections between Fibre Channel servers and devices in a SAN environment.
• The HAFM application. This graphical user interface (GUI) resides on the HAFM appliance and provides a single point of management for all directors, and a launching point for the Director 2/140 Element Manager. • Simple network management protocol (SNMP). A SNMP agent is implemented through the HAFM application that allows administrators on SNMP management workstations to access director management information using any standard network management tool.
• Diagnostic software that performs power-on self-tests (POSTs) and port diagnostics (internal loopback, external loopback, and Fibre Channel (FC) wrap tests). The FC wrap test applies only when the director is configured to operate in FICON management style. • An internal modem for use by support personnel to dial in to the HAFM appliance for event notification and to perform remote diagnostics.
Zoning The director supports a name server zoning feature that partitions attached devices into restricted-access groups called zones. Devices in the same zone can recognize and communicate with each other through switched port-to-port connections. Devices in separate zones cannot communicate with each other. Zoning is configured by authorizing or restricting access to name server information associated with device N_Ports that attach to director fabric ports (F_Ports).
• Fabric A unzoned and Fabric B unzoned—The fabrics join successfully, and the resulting fabric remains unzoned. • Fabric A zoned and Fabric B unzoned—The fabrics join successfully, and fabric B automatically inherits the zoning configuration from fabric A. • Fabric A unzoned and Fabric B zoned—The fabrics join successfully, and fabric A automatically inherits the zoning configuration from fabric B.
Front view Figure 1 shows Director 2/140 components accessible from the front of the director. Component descriptions follow the figure. 1 2 3 4 1 Front bezel 3 UPM cards (32) 2 Power and system error LEDs 4 CTP cards Figure 1 Director components—front CTP card The Director 2/140 ships with two Control Processor (CTP) cards. The active CTP card initializes and configures the director after power on, and contains the microprocessor and associated logic that coordinate director operation.
Each card faceplate contains a green light emitting diode (LED) that turns ON if the card is operational and active, and an amber LED that turns ON if the card fails. The LEDs are OFF on the backup CTP. The amber LED FLASHES if beaconing is enabled. Power/system LED assembly The bezel at the top front of the director includes an amber system error light-emitting diode (LED) and a green power LED.
• If the G_Port is attached to another director to form an Interswitch Link (ISL), the port functions as an expansion port (E_Port). A multi-switch fabric is formed through multiple directors and ISLs. Figure 2 shows the faceplate of an UPM. UPM 1 2 3 1 Card LED 2 Port LEDs 3 Port connectors (G_Ports) SHR-2 Figure 2 UPM card LEDs and connectors Single-mode or multi-mode fiber-optic cables attach to UPM cards through small form factor pluggable (SFP) optic transceivers.
Rear view Figure 3 shows the components accessible from the rear of the Director 2/140 . 1 2 3 4 5 6 1 Fan modules 4 SBAR assemblies 2 UPM cards (3) 5 AC modules 3 Maintenance port 6 Power supplies Figure 3 Director components—rear Fan modules Three fan modules, each containing one system fan (three system fans total), provide cooling for director FRUs, as well as provide redundancy for continued operation if a fan fails.
The backup SBAR takes over operation if the active assembly fails, and provides the ability to maintain connectivity and data frame transmission without interruption. The transition to the backup assembly is transparent to attached devices. Each SBAR assembly consists of a card and steel carriage that mounts flush on the backplane. The carriage provides protection for the back of the card, distributes cooling airflow, and assists in aligning the assembly during installation.
• Loopback plug—An SFP multi-mode (short-wave laser) or single-mode (long-wave laser) loopback plug (Figure 5), is required to perform port loopback diagnostic tests. One loopback plug is shipped with the director, depending on the type of port transceivers installed. Both plugs are shipped if short-wave laser and long-wave laser transceivers are installed.
Tools supplied by service personnel The following tools are expected to be supplied by service personnel performing director installation or maintenance actions. Use of the tools may be required to perform one or more test, service, or verification tasks. • Scissors or pocket knife—A sharp cutting edge (scissors or knife blade) may be required to cut the protective strapping when unpacking replacement FRUs.
Table 2 Director optional kits (continued) Supporting kit Description 35km Extended Reach Optical Transceiver Kit, Part Number: 300836-B21 Provides 35km long-wave optical transceiver for the director. 2Gb UPM Port Module Kit, Part Number: 316094-B21 Provides 4 additional short-wave ports for the Director 2/140.
Overview
2 Installing and configuring the director This chapter describes tasks to install, configure, and verify operation of the director.
• Obtain the required fiber-optic cables (multi-mode or single-mode). Verify cable length and required connectors. • Obtain an HP 19-inch equipment rack. • Verify that the front panel air temperature does not exceed 40 °C (104 °F) during operation. NOTE: Height measurements are sometimes described in rail units (Us). One U is 1.75 in. . • Verify that there is space in the rack. The director is 12U (20 in) high. • Verify that the rack is stable.
• Maintenance terminal (desktop or notebook computer)—required to configure director network addresses and acquire event log information through the maintenance port. Computer requirements include: • Microsoft Windows 98, Windows Millennium Edition, Windows NT 4.0, Windows 2000, or Windows XP operating system installed. • RS-232 serial communication software (for example, ProComm Plus or HyperTerminal). NOTE: The HAFM appliance may be used for the maintenance terminal function.
Install the director on a desktop To install the director on a desktop: 1. Position the director on a table or desktop as directed by the customer. CAUTION: Four person lift—the director weighs approximately 167 lbs. Do not attempt to lift or carry the director with fewer than four people. Failure to observe this CAUTION may result in injury to personnel or damage to the director. 2. Verify all field-replaceable units (FRUs), including logic cards, fans, and power supplies are installed as ordered. 3.
4. Connect the remaining ends of the AC power cords to separate (for redundancy) facility power sources that provide single-phase, 180 to 264 volt alternating current (VAC). The director powers on and performs power-on self-tests (POSTs). During POSTs: a. Amber LEDs on both CTP cards and all UPM cards illuminate momentarily. b. The green LED on each CTP card (active and backup) illuminates as the card is tested and UPM cards are tested. c.
5 Two (2) front mounting brackets 4 2 1 3 5 Figure 9 Brackets included in kit Required items Check that the following items are available before beginning the installation. • #2 Phillips screwdriver • Lift device (recommended) Tips for installing more than one director Review the following tips: • Install the first director in the lowest position of the rack. • Consider leaving a space of 1U open at the top and bottom of the rack, to allow easier cabling access.
2. Using a pallet jack, raise the pallet on which the director is mounted to the same height as the top surface of the lift device. 3. Slide the director across from the pallet to the lift device. 4. Determine the appropriate rack-mount position. Remember that the director is 20 inches or 12U high. Installing the shelf brackets in the rack The procedure for installing shelf brackets varies depending on the type of rack.
6. Repeat step 2 through step 5 to mount a small angle bracket on each interior vertical rail of the cabinet. Figure 10 Angle brackets mounted on cabinet rails in HP 9000, HP 10000, and HP 11000 Series rack 7. Attach two shelf brackets to the angle brackets on each side of the cabinet using eight (8) pan head screws and a #2 Phillips head screwdriver (Figure 11).
NOTE: Center each shelf bracket between the interior vertical rails of the rack cabinet. Figure 11 Shelf brackets mounted in HP 9000, HP 10000, and HP 11000 Series rack 8. Continue to ”Attaching the mounting hardware to the director” on page 36. Installing shelf brackets in an HP Rack system/e or 19-inch EIA rack The shelf brackets mount directly to the interior vertical rails of the HP rack system/e or 19-inch EIA rack using cage nuts and Phillips panhead screws.
5. Repeat step 4 for each of the three remaining interior vertical rails. 6. Secure a shelf bracket to the interior vertical rails using four (4) Phillips panhead screws with split lock and flat washers. 7. Repeat step 6 to secure the second shelf bracket on the opposite side of the rack. 8. Continue to ”Attaching the mounting hardware to the director” on page 36. Attaching the mounting hardware to the director Use these steps to secure the mounting hardware to the director.
1. Select one of the exterior vertical rails at the front of the cabinet. From the bottom of the shelf bracket, count up 3U (9 holes) and insert the first of three cage nuts. 2. Count up 3U (9 holes) from the cage nut you just installed and insert the next cage nut. 3. Count up 3U (9 holes) from the second cage nut and insert the third cage nut. 4. To install cage nuts in the other front rail, repeat step 1 through step 3.
1. Align a rear mounting bracket with the cage nuts you installed earlier, and the screw holes in the rear mounting plate attached to the Director 2/140. 2. Attach a rear mounting bracket to a rear mounting plate by installing three (3) Phillips panhead screws in the mounting plate holes. Do not tighten. 3. Adjust the position of the rear bracket so that the holes align with the cage nuts installed in the cabinet rail. 4.
NOTE: To ensure redundancy, install a second, optional PDU; and connect each PDU power cord to a separate PDU. Note that the Director 2/140 does not have a power switch. Therefore, the Director 2/140 powers on when its power cords are connected to facility power. Figure 13 AC power connections (director) Power-on self test Use the following steps to run a power-on self test (POST): 1. Power on the PDUs (if used). The director powers on.
• MAC address—The Media Access Control (MAC) address is programmed into FLASH memory on the CTP card at the time of manufacture. The address is in xx.xx.xx.xx.xx.xx format, where xx is a hexadecimal pair. • IP address—The factory preset, default IP address is 10.1.1.10. If the Reset Configuration option is selected from HAFM, the director resets to the default address of 10.1.1.10. If multiple directors are installed on the same LAN, each director (and appliance) must use a unique IP address.
1. Remove the protective cap from the 9-pin maintenance port at the rear of the director (a flat-tip screwdriver may be required). See Figure 14 1. 1 Maintenance port 2 RS-232 port 3 Null Modem cable Figure 14 Connecting the null modem cable between the director and a workstation 2. Connect the 9-pin end of the RS-232 modem cable to the maintenance port. 3. Connect the other cable end to a 9-pin communication port (COM1 or COM2) at the rear of the local workstation. 4.
The Connection Description dialog box appears (Figure 15). Figure 15 Connection Description dialog box 5. Enter 2140 in the Name box and click OK. The Connect To dialog box appears (Figure 16). Figure 16 Connect To dialog box 6. Ensure the Connect using box displays COM1 or COM2 (depending on the serial communication port connection to the director) and click OK. The COMn Properties dialog box appears (Figure 17). Figure 17 COMn Properties dialog box 7.
• Bits per second: 115200 • Data bits: 8 • Parity: None • Stop bits: 1 • Flow control: Hardware 8. Click OK. The HyperTerminal window appears. 9. At the > prompt, enter the user-level password (the default is password) and press Enter. The password is case-sensitive. The HyperTerminal window appears with a C> prompt at the top of the window (Figure 18). 10.At the C> prompt, enter ipconfig and press Enter. The HyperTerminal window lists the following: • MAC Address • IP Address (default is 10.1.1.
When the new network addresses are configured at the director, the message Request completed OK appears at the bottom of the HyperTerminal window. 13.Select Exit from the File menu. A HyperTerminal dialog box appears (Figure 19). Figure 19 HyperTerminal dialog box (1) 14.Click Yes. A second HyperTerminal dialog box appears (Figure 20). Figure 20 HyperTerminal dialog box (2) 15.Click No to exit and close the HyperTerminal application. 16.Power off the maintenance terminal: a. Select Start > Shut Down.
1. Connect one end of an Ethernet cable to the RJ-45 connector on each CTP card (Figure 21). 1 Remote workstation 3 2 Ethernet hub or switch (customer supplied) HAFM appliance (laptop or rack-mount) 4 Director 2/140 Figure 21 LAN-connect the director 2. Connect the remaining end of each Ethernet cable to the LAN as directed by the customer’s network administrator. NOTE: If an HAFM appliance is not available, use the Embedded Web Server (EWS) interface.
Record or verify HAFM appliance restore information Configuration information must be recorded to restore the HAFM appliance in case of hard drive failure. The Windows 2000 operating system and the HAFM and director Element Manager must also be restored. Refer to the HP StorageWorks Director 2/140 service manual for instructions. To record or verify HAFM appliance configuration information, refer to the HP StorageWorks HA-Fabric Manager appliance installation guide for instructions.
6. If you want to generate a sequence of IP addresses, perform the following: a. Select the Generate a sequence of IP addresses box. b. Enter the last IP address in the Last IP box. NOTE: octets. All IP addresses in a sequence must be on the same subnet and have the same first three 7. Click OK. Verify communication between the director and HAFM appliance Follow these steps to check director-to-server communication: 1.
In the example, the director’s status is operational as indicated by the green circle in the alert panel. Figure 24 Hardware View page Set director date and time The Director Element Manager log entries are stamped with the date and time received from the director. Use these steps to set the effective date and time for the director: NOTE: The director and HAFM synchronize at least once daily. 1. At the Hardware View, select Configure > Date/Time.
• Synchronize date and time, page 49 Figure 25 Configure Date and Time dialog box Set date and time manually Use these steps to set the director date and time manually: 1. At the Configure Date and Time dialog box, select the Periodic Date/Time Synchronization box to deselect the option (no check in the box). The grayed-out Date and Time fields activate. 2.
Frequently used HAFM settings This section summarizes the most common HAFM tasks including: NOTE: For a complete reference on HAFM functionality, refer to the HAFM user guide.
If the director is offline, the Set Online State dialog box appears, indicating the status is Offline. 4. Click Set Online. A Warning dialog box appears, indicating status is online. 5. Click OK. The Status table appears Online. Setting the director offline When the director is set offline, all ports are set offline. The director transmits the offline sequence (OLS) to attached devices, and the devices cannot log in to the director. Use these steps to set the director offline: 1.
Each director should be configured with a unique name. If the director is installed on a public LAN, the name should reflect the director’s Ethernet network DNS host name. For example, if the DNS host name is SAN140.hp.com, the name entered in this dialog box is SAN140. 3. Enter a director description of 255 or fewer alphanumeric characters in the Description box. 4. Enter the director’s physical location (255 or fewer alphanumeric characters) in the Location box. 5.
CAUTION: Setting the director offline terminates all Fibre Channel connections. 2. Select Configure > Operating Parameters > Switch Parameters. The Configure Switch Parameters dialog box appears (Figure 28). Figure 28 Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID. Change this value if the director will participate in a multi-switch fabric. 3.
domain ID is already allocated, an unused domain ID is assigned. Note that you must set the director offline before you can change to the preferred domain ID. The preferred domain ID must be unique for each director and switch in a fabric. If two switches or directors have the same preferred domain ID, the E_Ports segment, causing the fabric to segment. For more information on domain ID, refer to the section on domain ID assignment for multi-switch fabrics in the planning guide.
and storage device vendor to determine if enabling Domain RSCNs will cause problems with your HBA or storage products. NOTE: This option is required if Enterprise Fabric Mode (optional SANtegrity Binding feature) is enabled. The default state is enabled. Suppress RSCNs on zone set activations Fabric format domain register for state change notifications (RSCNs) are sent to ports on the switch following any change to the fabric's active zone set.
4. After you change settings, click Activate. 5. Back up the configuration data when you are finished configuring the switch. 6. Set the director online. For instructions, see ”Setting the director online” on page 50. Fabric parameters Configure the following parameters as required by your fabric. BB_Credit Configure the director to support buffer-to-buffer credit (BB_Credit) from 1 through 60. This is the value used for all ports, except those configured for extended distance buffering (10-100 km).
If all directors are set to Principal or Default, the director with the highest priority and the lowest WWN becomes the principal director. The following are some examples of principal director selection when directors have these settings: • If you have three directors and set all to Default, the director with the lowest WWN becomes the principal director.
Configuring switch binding This feature is managed through the Switch Binding submenu options available on the Element Manager Configure menu. Using Switch Binding, you can specify devices and switches that can attach to director and switch ports. This provides security in environments that include a large number of devices by ensuring that only the intended set of devices attach to a switch or director.
NOTE: If the director supports BB_Credits by port, the 10-100 Km column is replaced by an RX BB Credit column. d. If the director supports BB_Credits by port, right-click the RX BB Credit column. The RX BB Credits dialog box appears. NOTE: The port must be offline to change the BB_Credit field. • For switches without buffer pools, this dialog box allows you to: Set all...
A Speed list appears. Select 1Gb/sec, 2Gb/sec, or Negotiate as the desired setting depending on the speed capability of the device to be plugged into the port. A right-click in the Speed column allows selecting from a pop-up menu to set all ports to 1Gb/sec, 2Gb/sec, or Negotiate. h. Click the Port Binding box to enable WWN binding for the port, which allows only a specific device to attach to the port. This device is specified by the WWN or nickname entered into the Bound WWN column.
The Configure SNMP dialog box appears (Figure 31). Figure 31 Configure SNMP dialog box a. For each trap recipient to be configured, enter a community name of 32 or fewer alphanumeric characters in the associated Community Name box. The community name is incorporated in SNMP trap messages to ensure against unauthorized viewing or use. b. Click the box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled).
The Email Event Notification Setup dialog box appears (Figure 32). Figure 32 Email Event Notification Setup dialog box 2. To enable e-mail transmission of configured addresses, select Enable Email Event Notification. A check appears in the box when transmission is enabled. NOTE: The enable function must be activated for each director or switch through the Element Manager. E-mail notification can be active for some directors or switches and inactive for others. 3.
The HAFM 8.6 Server Users dialog box appears (Figure 33). Figure 33 HAFM 8.6 Server Users dialog box 7. To enable e-mail notification for a user, select the box in the Email column. An unchecked box indicates e-mail notification is not enabled. 8. To configure event types for which e-mail notification is sent, select the Filter link adjacent to the check box. The Define Filter dialog box appears (Figure 34). Figure 34 Define Filter dialog box 9. Select the filters that you want for this user. 10.
13.Click Send Test E-mail. A test message is sent to configured e-mail recipients. 14.Click OK to save the information and close the Email Event Notification Setup dialog box. 15.Maximize the Hardware View (Element Manager). 16.At the Hardware View, select Maintenance > Enable E-Mail Notification. A check appears in the box to indicate e-mail notification for the director is enabled, and the menu closes. NOTE: Use HAFM to enable or disable e-mail event notification for each director.
• A yellow triangle appears by the Threshold Alerts box in the Port Properties dialog box. • Detailed threshold alert data is recorded in the Threshold Alert Log. Use the Threshold Alerts option on the Configure menu to configure the following: • Name for the alert. • Type of threshold for the alert (Rx, Tx, or either). • Active or inactive state of the alert. • Threshold criteria: • Percent traffic capacity utilized—The percent of the port’s throughput capacity achieved by the measured throughput.
The New Threshold Alert dialog box appears (Figure 37). Figure 37 New Threshold Alerts dialog box—first screen 3. Enter a name from one to 64 characters in length. All characters in the ISO Latin-1 character set, excluding control characters, are allowed. 4. Select one of the following from the Threshold Type list: • Receive—An alert will occur if the threshold set for receive throughput is reached. • Transmit—An alert will occur if the threshold set for transmit throughput is reached.
NOTE: Click Previous if you need to return to the previous screen. Figure 38 New Threshold Alerts dialog box—second screen 6. Enter a percentage from 1 through 100 for % utilization. When throughput reaches this percentage of port capacity, a threshold alert will occur. 7. Enter the amount of cumulative minutes in which the % utilization should exist during the notification interval before an alert is generated. The valid range is from 1 to the interval value set in step 8.
A new screen appears for selecting ports for the alerts (Figure 39). Figure 39 New Threshold Alerts dialog box—third screen 10.Select either Port Type or Port List. • If you select Port Type, selecting either E_Ports or F_Ports to cause an alert to generate for all ports configured as E_Ports or F_Ports, respectively.
Figure 40 New Threshold Alerts dialog box—summary screen 12.Click Finish. The Configure Threshold Alerts dialog box appears (Figure 41). Figure 41 Configure Threshold Alerts dialog box 13.At this point, the alert is not active. To activate the alert, select the alert information that appears in the Configure Threshold Alerts list and then click Activate. The alert is activated. Modifying alerts Use the following steps to modify an existing threshold alert configuration. 1.
8. At the summary screen, click Finish. Activating or deactivating alerts Use the following steps to activate or deactivate existing threshold alerts. In the active state, notifications are generated for the alert. In the inactive state, notifications do not occur. 1. At the Hardware View page, select Configure > Threshold Alerts. The Configure Threshold Alerts dialog box appears. The port’s current state, inactive or active, is listed under the State column. 2.
• Radius Servers—Allows you to set Radius server parameters that the switch uses to communicate the authentication information to the designated Radius servers. Figure 42 Configure SANtegrity Authentication dialog box Backing up HAFM configuration data It is important to back up the HAFM configuration data. This data is used to restore the HAFM appliance operating environment in case of hard drive failure.
Enabling Embedded Web Server Use the following steps to enable EWS: 1. At the Hardware View page, select Configure > Enable Web Server. Selecting Enable Web Server automatically places a check in the box. 2. Select Enable Web Server again to remove the check and disable the EWS interface. When disabled, remote users cannot access the interface. For complete procedures on using EWS, refer to the HP StorageWorks Embedded Web Server user guide. Enabling Telnet Use the following steps to enable Telnet: 1.
The Hardware View appears. 7. Double-click the graphical port connector used for the fabric ISL. The Port Properties dialog box appears (Figure 43). Figure 43 Port Properties dialog box 8. Verify that the Link Incident box displays None. If an ISL segmentation or other problem is indicated, consult the HP StorageWorks Director 2/140 service manual to isolate the problem. If no problems are indicated, installation is complete.
Each client must have access to the LAN segment on which the HAFM appliance is installed. Director administrative functions are accessed through the LAN and appliance. Use this section to install the HAFM client on a remote workstation.
b. Download SNMP MIB files—The Management Information Base (MIB) files are provided in standard ASN.1 syntax and may be installed into the MIB database of any SNMPv2 compliant Network Management Station. Figure 44 HAFM remote client install 5. If you selected Install HAFM remote client application, follow the instructions provided that pertains to your platform. 6. After you have downloaded the installer executable, the InstallAnywhere Wizard appears.
NOTE: The default Windows 2000 user name is Administrator and the default password is password. The user name and password are case-sensitive. Figure 45 HAFM 8.6 Log In dialog box 2. Enter the HAFM appliance IP address in the Network Address box. • The default address that appears in the Network Address box is the address of the last server accessed. • Click the Network Address arrow to see a list of network addresses of all HAFM appliances that were accessed from your computer.
The View All - HAFM 8.6 window appears (Figure 46). Figure 46 View All - HAFM 8.
Installing and configuring the director
3 Managing firmware versions The director 2/140 internal operating code is downloaded from the HAFM appliance and stored on a CTP card. Up to eight (8) versions can be stored on the HAFM appliance hard drive and made available for download to a director.
Adding a firmware version The firmware version shipped with the director is provided on the director documentation CD. Subsequent firmware versions to upgrade the director are provided to customers through the HP website. NOTE: When adding firmware, follow procedural information in the release notes that accompany the firmware version. The release notes provide supplemental information to this procedure.
The New Firmware Version dialog box appears (Figure 48). Figure 48 New Firmware Version dialog box 6. Select the desired firmware version file (downloaded in step 1) from the HAFM appliance backup drive, CD-ROM drive, or hard drive. Verify that the correct directory path and filename display in the File name box and click Save. The New Firmware Description dialog box appears (Figure 49). Figure 49 New Firmware Description dialog box 7.
3. Select Maintenance > Firmware Library. The Director Firmware Library dialog box appears (Figure 47). 4. Select the firmware version to be modified and click Modify. The Modify Firmware Description dialog box appears. 5. Enter a modified description (up to 24 characters in length) for the firmware version and click OK. HP recommends that you include the installation date and text that uniquely identifies the firmware version in the description.
Use these steps to download a firmware version to a director: 1. Open the HAFM application. The View All - HAFM 8.6 main window appears. 2. Before downloading firmware to a director, ensure the required, compatible version of the HAFM application is running on the HAFM appliance. Refer to the release notes that shipped with HAFM. a. Select Help >About. The About dialog box appears and lists the HAFM application version. Click OK to close the dialog box. b.
If a problem occurs and a corresponding message appears, refer to the HP StorageWorks Director 2/140 service manual for specific information on isolating the problem. If no error occurs, the Send Firmware confirmation box appears. 7. Click Yes. The Send Firmware dialog box appears. As the download begins, a Writing data to FLASH message appears at the top of the dialog box, followed by a Sending Files message.
A Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
• Connect the equipment into an outlet on a circuit that is different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Declaration of conformity for products marked with the FCC logo, United States only This device complies with Part 15 of the FCC Rules.
Laser safety warning WARNING! To reduce the risk of exposure to hazardous radiation: • Do not try to open the laser device enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. • Allow only HP authorized service technicians to repair the laser device.
Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Japanese notice Korean notices Safety Battery replacement notice Your computer is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product.
WARNING! Your computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. There is risk of fire and burns if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose to temperatures higher than 60°C. • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. • Replace only with the HP spare part designated for this product.
Japanese power cord notice Electrostatic discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Regulatory compliance and safety
B Technical specifications This appendix contains the following information: • Physical dimensions, page 93 • Environmental specifications, page 93 • Power requirements, page 94 • Operating tolerances, page 94 • Laser information, page 95 Physical dimensions Table 4 lists Director 2/140 dimensions. Table 4 Dimensions Dimension Size Height 52.7 cm (20.9 in) Width 44.1 cm (17.5 in) Depth 61.0 cm (24.2 in) Weight 75.9 kg (167 lb) Shipping Weight 102.
Power requirements Table 6 lists Director 2/140 power requirements. Table 6 Power requirements Specification Value Input voltage 180 to 264 VAC Input current 4.66 amps at 180 VAC Input power 842 watts Input frequency 47/63 Hz Operating tolerances Table 7 lists heating and cooling specifications, shock and vibration tolerances, acoustical noise, and inclination.
Laser information Three configurations of cards with fixed optics will be provided for each of the connector types: four extended long-wave ports, four long-wave ports, and four short-wave ports. Table 8 lists the 2 Gb laser specifications.
Technical specifications
Index A AC module 22 AC system harness 22 accumulators 90 AIX operating system 74 alerts, introduction 14 alkaline battery warning 90 asynchronous RS-232 null modem cable 23 authorized reseller, HP 11 Avis Canadien, regulatory compliance notice 87 B backing up director configuration file 84 batteries recycling or disposal 90 replacement notice 89 warning 90 Taiwan EPA recycling and disposal 90 bb_credit 56 beaconing LED 19 beaconing, introduction 15 boot straps, using 91 brackets, installing 33, 35 BSMI, r
degraded fabric performance, causes of 16 diagnostic software, introduction 15 dialog boxes configure fabric parameters 55 configure feature key procedure 71 configure switch parameters 52, 53 director AC module 22 connecting to power 38 desktop, installing 30 e_d_tov 17 fibre channel addresses 53 general description 13 hardware components 17 installing 37 management, overview 13 NV-RAM 52, 55 r_a_tov 17 rerouting delay 54 securing 37 tools supplied 22 unpacking, inspecting, installing 29 weight caution 30
notice 85 feature key 71 configuring 71 features of the director 17 Federal Communications Commission.
installation tasks backing-up configuration data 71 director unpacking, inspecting, installing 29 recording and verifying HAFM appliance restoration information 46 unpacking, inspecting, and installing Ethernet hub 73 Intel Pentium processor 74 Internet Explorer 74 interop mode 57 homogeneous fabric 57 open fabric 1.
O R OFC class 1 laser transceivers 19 online state, setting 50 open fabric 1.
site plan 27 SNMP agent general description 14 SNMP trap messages maximum recipients 15 Solaris operating system 74 static electricity 91 static-dissipating work mat 91 static-safe containers storing products 91 transporting products 91 static-sensitive devices 91 straps, ground boot 91 heel 91 toe 91 Subscriber’s choice, HP 11 SunOS operating system 74 suppress RSCNs on zone set activations 55 switch error-detection, reporting, and serviceability features 14 multi-switch fabric 16 switch binding 58 switch
alkaline batteries 90 battery replacement 90 lasers, radiation 87 web server, overview 14 web sites HP storage 12 HP Subscriber’s choice 11 weight, director caution 30 Windows 2000 default password 76 default user name 76 Windows operating systems, versions 24, 74 work mat, static-dissipating 91 workstation, UNIX 74 wrist straps specifications 91 using 91 WWN principal switch 56 Z zone set, description of 16 zoning joining, rules of 16 Director 2/140 installation guide 103
