hp StorageWorks director 2/140 installation guide Part Number: AA-RTDSA-TE/958-000275-000 First Edition (January 2003) This guide provides procedures for setting up, configuring, and managing the HP StorageWorks Director 2/140.
© Hewlett-Packard Company, 2003. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright.
Contents About This Guide Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Symbols in Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Tools Supplied with the Director . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15 Tools Supplied by Service Personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–16 Optional Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–17 2 Installing and Configuring the Director 2/140 Summary of Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Rerouting Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Domain RSCNs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Fabric Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fabric Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Editing the Switch Membership List . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable and Online State Functions . . . . . . . . . . . . . . . . . . . . Zoning with Switch Binding Enabled . . . . . . . . . . . . . . . . . . . . . . . . Enterprise Fabric Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fabric Binding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch Binding . . . . . . . . . . . .
Contents Configure User Rights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–19 4 Manage Firmware Versions Determine a Director Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add a Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modify a Firmware Version Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Laser Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–3 C Electrostatic Discharge Precautions Against Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–1 Grounding Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 2–19 2–20 2–21 2–22 2–23 2–24 2–25 2–26 2–27 2–28 2–29 2–30 2–31 3–1 3–2 3–3 3–4 3–5 3–6 3–7 3–8 3–9 3–10 3–11 3–12 3–13 4–1 4–2 4–3 4–4 4–5 4–6 Configure Threshold Alerts dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–40 New Threshold Alerts dialog box—first screen . . . . . . . . . . . . . . . . . . . . . . . 2–41 New Threshold Alerts dialog box—second screen. . . . . . . . . . . . . . . . . . . . . 2–42 New Threshold Alerts dialog box—third screen . . . . . . . . . . .
2–2 2–3 B–1 B–2 B–3 B–4 B–5 Director Operational States and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . Available Code Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Requirements . . . . . . . . . . . . . . . . . . . . . . .
About This Guide This guide provides information on installing, configuring, managing, and verifying operation of the HP StorageWorks Director 2/140. The Director 2/140 switch connects storage devices, hosts, and servers in a SAN. The director is easily managed and configured to optimize the performance of your SAN. Intended Audience This guide is part of a documentation set that supports the Director 2/140.
About This Guide Document Conventions The conventions included in Table 1 apply. Table 1: Document Conventions Element Convention Cross-reference links Blue text: Figure 1 Key names, menu items, buttons, and dialog box titles Bold File names, application names, and text emphasis Italics User input, command names, system responses (output and messages) Monospace font Variables Monospace, italic font Website addresses Sans serif font (http://thenew.hp.
About This Guide Symbols on Equipment Any enclosed surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards. Enclosed area contains no operator serviceable parts. WARNING: To reduce the risk of injury from electrical shock hazards, do not open this enclosure. Any RJ-45 receptacle marked with these symbols indicates a network interface connection.
About This Guide Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manually handling material. Rack Stability WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: • The leveling jacks are extended to the floor.
About This Guide • Product serial numbers • Product model names and numbers • Applicable error messages • Operating system type and revision level • Detailed, specific questions HP Website The HP website has the latest information on this product, as well as the latest drivers. Access storage at: http://thenew.hp.com/country/us/eng/prodserv/storage.html. From this website, select the appropriate product or solution.
1 Overview This chapter contains the following HP StorageWorks Director 2/140 information: • Director Description, page 1–1 • Features, page 1–3 • Hardware Components, page 1–8 • Tools and Test Equipment, page 1–14 • Optional Kits, page 1–17 Director Description The director is a second-generation, 140-port product that provides dynamic switched connections between Fibre Channel servers and devices in a SAN environment.
Overview 1 2 3 4 5 1 2 3 Ethernet hub Director 2/140 HAFM server 4 5 Director 2/140 Director 2/140 Figure 1–1: Director 2/140s and HAFM server in a cabinet 1–2 director 2/140 installation guide
Overview Features Features of the Director 2/140 include: • Scalable from 64 to 140 User ports • 100% dynamic non-blocking, cut through switching with congestion queuing • Online error detection, error isolation, and error recovery • Redundant, hotpluggable components • Full duplex 200 MB/sec per port performance • Less than 2-µs average switch latency • 100-km distance support (60 buffers), with use of repeaters • Small form factor, hot-pluggable optical transceivers, auto configure G_ports
Overview Product Manager application. Administrators launch the EWS interface from a remote PC by entering the director’s IP address as the internet URL, then entering a user name and password at a login screen. The PC browser then becomes a management console. NOTE: The default user name for the right to view status and other information is “operator.” The default user name for the right to modify configuration data, perform maintenance tasks, or perform other options is “administrator.
Overview • Automatic notification of significant system events (to support personnel or administrators) through e-mail messages or the call-home feature at the HAFM server. • A modem for use by support personnel to dial-in to the HAFM server for event notification and to perform remote diagnostics.
Overview management workstations can be configured through the Product Manager application to receive unsolicited SNMP trap messages. The trap messages indicate operational state changes and failure conditions. NOTE: For more information about SNMP support provided by HP products, refer to the hp StorageWorks SNMP reference guide for directors and edge switches. The director supports a name server zoning feature that partitions attached devices into restricted-access groups called zones.
Overview Because a multi-switch fabric is typically complex, maintenance personnel should be aware that several factors can degrade fabric performance or cause connectivity failures. These factors include: • Domain ID assignment—Each director in a fabric is identified by a unique domain ID that ranges from 1 through 31. A domain ID of 0 is invalid. If two operational fabrics join, they determine if any domain ID conflicts exist between the fabrics.
Overview — Incompatible zoning configurations—Zoning configurations for the directors are not compatible. — Build fabric protocol error—A protocol error is detected during the process of forming the fabric. — No principal switch—No director in the fabric is capable of becoming the principal switch. — No response from attached switch—After a fabric is created, each director in the fabric periodically verifies operation of all attached switches and directors.
Overview 1 2 3 4 1 2 Front bezel Power and system error LEDs 3 4 UPM cards (32) CTP cards Figure 1–2: Director components—front Power/System LED Assembly The bezel at the top front of the director includes an amber system error light-emitting diode (LED) and a green power LED. These LEDs are actuated and controlled by a Power/System LED Assembly which is accessed from the rear of the director. The power LED illuminates when the director is powered on and operational.
Overview Power Supplies The Director 2/140 uses redundant, load-sharing power supplies which step down and rectify facility input power to provide 48-VDC power to director FRUs. The power supplies also provide over-voltage and over-current protection. Either power supply can be replaced while the switch is powered on and operational. Each power supply has a separate backplane connection to allow for different AC power sources. The power supplies are input rated at 180 to 264 VAC.
Overview UPM 1 2 1 2 3 Card LED Port LEDs Port Connectors (G_Ports) 3 Figure 1–3: UPM card LEDs and connectors Single-mode or multi-mode fiber-optic cables attach to UPM cards through small form factor pluggable (SFP) optic transceivers. The fiber-optic transceivers provide duplex connectors, and can be detached from UPM cards (through a 10-pin interface) for easy replacement. Three fiber-optic transceiver types are available.
Overview • Extended reach long-wave Laser—Long-wave laser transceivers that provide connections for transferring data over extended long distances (up to 35 kilometers) through 9-µm single-mode fiber. CTP Card The Director 2/140 ships with two Control Processor (CTP) cards. The active CTP card initializes and configures the director after power on, and contains the microprocessor and associated logic that coordinate director operation. The second CTP card serves as a backup.
Overview 1 2 3 4 5 6 1 2 3 Fan modules UPM cards (3) Maintenance port 4 5 6 SBAR assemblies AC modules Power supplies Figure 1–4: Director components—rear Fan Modules Three fan modules, each containing one system fan (three system fans total), provide cooling for director FRUs, as well as redundancy for continued operation if a fan fails.
Overview SBAR Assembly The director ships with two SBAR assemblies. The active SBAR is responsible for Fibre Channel frame transmission from any director port to any other director port. Connections are established without software intervention. The assembly accepts a connection request from a port, determines if a connection can be established, and establishes the connection if the destination port is available. The assembly also stores busy, source connection, and error status for each director port.
Overview Tools Supplied with the Director The following tools are supplied with the director. Use of the tools may be required to perform test, installation, service, or verification tasks. • Torque tool with hexagonal adapter—The torque tool with 5/32” hexagonal adapter as shown in Figure 1–5 is required to remove and replace director logic cards.
Figure 1–7: Fiber-Optic protective plug • Null modem cable—An asynchronous RS-232 null modem cable as shown in Figure 1–8 is required to configure director network addresses and acquire event log information through the maintenance port. The cable has nine conductors and DB-9 male and female connectors. Figure 1–8: Null modem cable Tools Supplied by Service Personnel The following tools are expected to be supplied by service personnel performing director installation or maintenance actions.
Overview • Standard flat-tip and cross-tip (Phillips) screwdrivers—Screwdrivers are required to remove, replace, adjust or tighten various FRUs, chassis, or cabinet components. • Electrostatic discharge (ESD) grounding cable with attached wrist strap—Use of the ESD wrist strap is required when working in and around the director card cage.
Overview Table 1–1: Director 2/140 Optional Kits (Continued) 1–18 Supporting Kit Description 10km Long Distance Optical Transceiver Kit, Part Number: DS-DMLNG-AA / 300835-B21 Provides 10 km long-wave optical transceiver for the Director 2/140. 35 km Extended Reach Optical Transceiver Kit, Part Number: DS-DMEXT-AA / 300836-B21 Provides 35 km long-wave optical transceiver for the Director 2/140.
2 Installing and Configuring the Director 2/140 This chapter describes tasks to install, configure, and verify operation of the Director 2/140. The director can be installed on a table or desk top, or mounted in any standard equipment rack. For a list of the factory-set defaults for the director and the Reset Configuration option, refer to Appendix B. Summary of Installation Tasks Table 2–1 summarizes installation tasks for the director, HAFM server, and Ethernet hub.
Installing and Configuring the Director 2/140 Table 2–1: Installation Task Summary (Continued) Description HAFM Server Required or Optional Page Optional but recommended and 2–16 required for availability of all features, such as event logging and call-home—if not done, then the director should be configured using the embedded web server (EWS) interface. Record or Verify HAFM Server Restore Information Required if HAFM Server task was done.
Installing and Configuring the Director 2/140 Table 2–1: Installation Task Summary (Continued) Description Using HAFM from a Remote Location director 2/140 installation guide Required or Optional Optional Page 2–64 2–3
Installing and Configuring the Director 2/140 Installation Options The director is installed in one of two configurations. The options are: • Table or desk top—One or more directors and an optional HAFM server are delivered and installed at the customer facility on a desk or table top. Ethernet cabling distance, and local area network (LAN) addressing issues must be considered.
Installing and Configuring the Director 2/140 • Verify that all other equipment installed in the rack is connected to a reliable ground connection; do not rely on connections to a branch circuit, such as a power strip. • HP recommends securing the rack mechanically to prevent it from tipping over during a natural disaster, such as an earthquake.
Installing and Configuring the Director 2/140 — Microsoft Windows 98, Windows Millennium Edition, Windows NT 4.0, Windows 2000, or Windows XP operating system installed — RS-232 serial communication software (for example, ProComm Plus, or HyperTerminal). NOTE: The HAFM server may be used for this function. The HyperTerminal application is included with the Windows 2000 operating system provided with the HAFM server.
Installing and Configuring the Director 2/140 Unpack and Inspect the Director Unpack and inspect the director(s) as follows: 1. Inspect the shipping containers for damage caused during transit. If a container is damaged, ensure a representative from the freight carrier is present when the container is opened. 2. Unpack the shipping containers and inspect each item for damage. Ensure the items match the items listed on the bill of materials (BOM). 3.
Installing and Configuring the Director 2/140 SHR-2594A Figure 2–1: AC power connections (director) WARNING: An HP-supplied power cord is provided for each director power supply. To prevent electric shock when connecting the director to primary facility power, use only the supplied power cord(s), and ensure the facility power receptacle is the correct type, supplies the required voltage, and is properly grounded. NOTE: The director does not have a power switch.
Installing and Configuring the Director 2/140 5. After successful POST completion, the green power LED on the front bezel, green LED on the active CTP card, and green PWR OK LEDs on both power supplies remain illuminated. 6. If a POST error or other malfunction occurs, refer to the hp StorageWorks director 2/140 service manual to isolate the problem. Power-On Self Test Use the following steps to run a Power-On Self Test (POST): 1. Power on the PDUs (if used). The director powers on.
Installing and Configuring the Director 2/140 If the Reset Configuration option is selected from HAFM, the director resets to the default address of 10.1.1.10. NOTE: If multiple directors are installed on the same LAN, each director (and server) must use a unique IP address. One director can use the factory-set address, but the addresses of the remaining directors require change. • Subnet mask—The subnet mask is 255.0.0.0.
Installing and Configuring the Director 2/140 3. Connect the other cable end to a 9-pin communication port (COM1 or COM2) at the rear of the local workstation. 4. Choose Start > Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box displays, as shown in Figure 2–2. Figure 2–2: Connection Description dialog box 5. Type 2140 in the Name field and click OK. The Connect To dialog box displays, as shown in Figure 2–3.
Installing and Configuring the Director 2/140 Figure 2–3: Connect To dialog box 6. Ensure the Connect using field displays COM1 or COM2 (depending on the serial communication port connection to the director), and click OK. The COMn Properties dialog box displays, as shown in Figure 2–4.
Installing and Configuring the Director 2/140 Figure 2–4: COMn Properties dialog box 7. Configure the Port Settings parameters as follows: • Bits per second: 115200 • Data bits: 8 • Parity: None • Stop bits: 1 • Flow control: Hardware 8. Click OK. The HyperTerminal window displays. 9. At the > prompt, type the user-level password (the default is password) and press the Enter key. The password is case-sensitive. The HyperTerminal window displays with an C> prompt at the top of the window.
Installing and Configuring the Director 2/140 10. At the C> prompt, type ipconfig and press Enter. The HyperTerminal window displays, as shown in Figure 2–5. • MAC Address • IP Address (default is 10.1.1.10) • Subnet Mask (default is 255.0.0.0) • Gateway Address (default is 0.0.0.0) Only the IP Address, Subnet Mask, and Gateway Address fields are configurable.
Installing and Configuring the Director 2/140 11. To change director network addresses, type the following at the C> prompt and press Enter. ipconfig xxx.xxx.xxx.xxx.yyy.yyy.yyy.yyy.zzz.zzz.zzz.zzz The IP address format is xxx.xxx.xxx.xxx. The subnet mask format is yyy.yyy.yyy.yyy. The gateway address format is zzz.zzz.zzz.zzz. The octets xxx, yyy, and zzz are decimals from 0 through 255. If a network address is to remain unchanged, type the current address in the respective field.
Installing and Configuring the Director 2/140 1 2 Remote workstation 3 Ethernet hub or switch (customer 4 supplied) HAFM server Director 2/140 Figure 2–6: LAN-connect the director 2. Connect the remaining end of each Ethernet cable to the LAN as directed by the customer’s network administrator. NOTE: If an HAFM server is not available, use the Embedded Web Server (EWS) interface. Attach the Ethernet LAN segment to an Internet connection and see Chapter 3.
Installing and Configuring the Director 2/140 • creating HAFM user names and passwords Record or Verify HAFM Server Restore Information Configuration information must be recorded to restore the HAFM server in case of hard drive failure. The Windows 2000 operating system and the HAFM and director Product Manager application must also be restored. Refer to the hp StorageWorks director 2/140 service manual for instructions.
Installing and Configuring the Director 2/140 Verify Communication Between the Director and HAFM Server Follow these steps to check director-to-server communication. 1. From the Products View page (as shown in Figure 2–8), take note of the shape and color of the symbol behind the director icon. Table 2–2 explains these symbols.
Installing and Configuring the Director 2/140 Table 2–2: Director Operational States and Symbols Operational State Symbol Operational—Director-to-server communication has been established, the director is operational, and no failures are indicated. Degraded—Director-to-server communication has been established, but the director is operating in degraded mode and requires service. This condition is typical if a port or redundant FRU fails. Go to step 2.
Installing and Configuring the Director 2/140 Figure 2–9: Hardware View page (with FRU failures) Set Director Date and Time The Director 2/140 Product Manager log entries are stamped with the date and time received from the director. Use these steps to set the effective date and time for the director. NOTE: The director and HAFM synchronize at least once daily. 1. At the Hardware View page, click the Configure menu. 2. Choose Date/Time from the drop-down menu.
Installing and Configuring the Director 2/140 3. Set director date and time manually, or set for periodic updates. For specific instructions, see the following sections: • Set Director Date and Time, page 2–20 • Synchronize Date and Time, page 2–22 Figure 2–10: Configure Date and Time dialog box Set Date and Time Manually Use these steps to set the director date and time manually. 1.
Installing and Configuring the Director 2/140 4. Click Activate to set the director date and time, and close the Configure Date and Time dialog box. Synchronize Date and Time Use these steps to set the director to periodically synchronize date and time with HAFM. 1. At the Configure Date and Time dialog box, choose the Periodic Date/Time Synchronization check box. The Date and Time fields are greyed-out and not selectable. 2.
Installing and Configuring the Director 2/140 • Configure and Enable Call-Home Features, page 2–38 • Configure Threshold Alerts, page 2–38 • Test Remote Notification, page 2–47 • Enable Embedded Web Server, page 2–48 • Enable Telnet, page 2–48 • Optional Features, page 2–48 Configure Feature Key A feature key is a string of alphanumeric characters consisting of both uppercase and lowercase. The following is an example of a feature key format: XxXx-XXxX-xxXX-xX.
Installing and Configuring the Director 2/140 2. Choose Configure > Features from the Product Manager window. The Configure Feature Key dialog box displays, as shown in Figure 2–11. Figure 2–11: Configure Feature Key dialog box 3. Click New to add a new feature key. The New Feature Key dialog box displays, as shown in Figure 2–12. Figure 2–12: New Feature Key dialog box 4. Enter the director’s feature key in the Key field and click OK.
Installing and Configuring the Director 2/140 5. Click Activate to activate the new feature key. An IPL will occur, during which the Ethernet connection between the HAFM server and director is momentarily interrupted. NOTE: If you click Activate, all current features will be replaced with new features. That is, if there are features shown in the current list that are not shown in the new list, then those features will be removed from the director. 6. Set the director back online. a.
Installing and Configuring the Director 2/140 2. Open HAFM. The Products View page displays. 3. Choose the appropriate director icon. The Hardware View page for the selected director displays. 4. Choose Maintenance > Set Online State. If the director is online, the Set Online State dialog box displays, indicating the status is Online. 5. Click Set Offline. A Warning dialog box displays, indicating the director will be set offline. 6. Click OK.
Installing and Configuring the Director 2/140 If the director is installed on a public LAN, the name should reflect the director’s Ethernet network DNS host name. For example, if the DNS host name is SAN140.hp.com, the name entered in this dialog box is SAN140. b. Type a director description of 255 or fewer alphanumeric characters in the Description field. c. Type the director’s physical location (255 or fewer alphanumeric characters) in the Location field. d.
Installing and Configuring the Director 2/140 Figure 2–14: Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID. Change this value if the director will participate in a multi-switch fabric. 1. Use information under “Switch Parameters” to change settings as required for parameters in this dialog box. 2. After you change settings, click the Activate button. 3. Set the director online.
Installing and Configuring the Director 2/140 Preferred NOTE: To change this value, you must first set the director offline. Choose Set Online State from the Maintenance menu to display the Set Online State dialog box, then click the Set Offline button. Be sure to set the director back online after you change this value. Use this field to set a unique domain ID for the director. The default value is 1. Set a value between 1 and 31.
Installing and Configuring the Director 2/140 Rerouting Delay Placing a check mark in the check box to the left of the Rerouting Delay option enables rerouting delay. This option is only applicable if the configured director is in a multi-switch fabric. The default state is disabled. Enabling the rerouting delay ensures that frames are delivered in order through the fabric to their destination.
Installing and Configuring the Director 2/140 attaching an IBM S/390 Parallel Enterprise or IBM zSeries server to the director and implementing inband director management through a Fibre Connection (FICON) channel. • Use Open Systems mode for all other (non-FICON) Fibre Channel environments. Configure Fabric Operating Parameters Use procedures in this section to set parameters on the director for fabric operation through the Configure Fabric Parameters dialog box.
Installing and Configuring the Director 2/140 3. Use information under “Fabric Parameters” to change settings as required for parameters in this dialog box. 4. After you change settings, click Activate. 5. Back up the configuration data when you are finished configuring the director. 6. Set the director online. For instructions, see “Set the Director Online” on page 2–25. Fabric Parameters Configure the following parameters as required by your fabric.
Installing and Configuring the Director 2/140 Switch Priority Setting this value determines the principal director for the multi-switch fabric. Choose Principal (highest priority), Default, or Never Principal (lowest priority) from the Switch Priority drop-down list. Setting these priority values determines the principal director selected for the multi-switch fabric.
Installing and Configuring the Director 2/140 • Open Fabric 1.0—Default. Select this mode if the fabric contains HP directors and switches, as well as other open-fabric compliant switches. Select this mode for managing heterogeneous fabrics. Configure Ports Perform this procedure to define Fibre Channel port names, configure ports as blocked or unblocked, enable extended distance operation and Link Incident (LIN) alerts, and define port types. 1. At the Hardware View page, choose Configure > Ports.
Installing and Configuring the Director 2/140 c. Click the 10-100 km check box to enable extended distance buffering for a port. A check mark in the box indicates the extended distance operation up to 100 kilometers (through repeaters) is enabled. d. Click the LIN Alerts check box to enable or disable LIN alerts for a port. A check mark in the box indicates alerts are enabled.
Installing and Configuring the Director 2/140 Figure 2–17: Configure SNMP dialog box a. For each trap recipient to be configured, type a community name of 32 or fewer alphanumeric characters in the associated Community Name field. The community name is incorporated in SNMP trap messages to ensure against unauthorized viewing or use. b. Click the check box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled).
Installing and Configuring the Director 2/140 3. Click Activate to save the information and close the dialog box. Configure and Enable E-mail Notification Use this procedure to configure and enable e-mail addresses and Simple Mail Transfer Protocol (SMTP) server addresses to receive e-mail notification of director (and other managed product) events. The addresses must be configured via HAFM, then enabled. See “Test Remote Notification” on page 2–47.
Installing and Configuring the Director 2/140 2. To enable email transmission of configured addresses, click Enable E-Mail Event Notification. A check mark displays in the box when transmission is enabled. NOTE: Using HAFM, enable or disable email event notification for each director individually. 3. Click OK to save the information and close the dialog box. 4. Double-click the Director 2/140 icon. The Hardware View page for the selected director displays. 5.
Installing and Configuring the Director 2/140 • A yellow triangle that displays in the Alert column of the Port List View. • A yellow triangle that displays by the Threshold Alerts field in the Port Properties dialog box. • Detailed threshold alert data recorded in the Threshold Alert Log. Use the Threshold Alerts option on the Configure menu to configure the following: • Name for the alert. • Type of threshold for the alert (Rx, Tx, or either). • Active or inactive state of the alert.
Installing and Configuring the Director 2/140 Figure 2–19: Configure Threshold Alerts dialog box 2. Click New. The New Threshold Alert dialog box displays, as shown in Figure 2–20.
Installing and Configuring the Director 2/140 Figure 2–20: New Threshold Alerts dialog box—first screen 3. Enter a name from one to 64 characters in length. All characters in the ISO Latin-1 character set, excluding control characters, are allowed. 4.
Installing and Configuring the Director 2/140 5. Click Next. A new screen displays with additional parameters, as shown in Figure 2–21. The name configured for the alert displays at the top of the screen. NOTE: Click Previous if you need to return to the previous screen. Figure 2–21: New Threshold Alerts dialog box—second screen 6. Enter a percentage from 1 through 100 for % utilization. When throughput reaches this percentage of port capacity, a threshold alert will occur. 7.
Installing and Configuring the Director 2/140 8. Enter the interval in minutes in which throughput is measured and threshold notifications can occur. The valid range is 5 minutes to 70,560 minutes. 9. Click Next. A new screen displays for selecting ports for the alerts, as shown in Figure 2–22. Figure 2–22: New Threshold Alerts dialog box—third screen 10. Choose either Port Type or Port List.
Installing and Configuring the Director 2/140 • For Port List, you can choose individual ports by clicking the check box by each port number or set all ports. Selecting Set All Ports places a check mark by each port number. Selecting Clear All Ports will clear the check marks by each port number. 11. Click Next. A final screen displays to provide a summary of your alert configuration, as shown in Figure 2–23. Figure 2–23: New Threshold Alerts dialog box—summary screen 12. Click Finish.
Installing and Configuring the Director 2/140 13. At this point, the alert is not active. To activate the alert, choose the alert information that displays in the Configure Threshold Alerts table and click Activate. The alert is activated as shown in Figure 2–24. Figure 2–24: Configure Threshold Alerts dialog box—alert activated Modify Alerts Use the following steps to modify an existing threshold alert configuration. 1. At the Hardware View page, choose Configure > Threshold Alerts.
Installing and Configuring the Director 2/140 5. Click Next when you are done. A Modify Threshold screen displays where you can change the % utilization, cumulative minutes for the threshold to occur before notification, and the time interval for measuring throughput and for alert notification. 6. Make appropriate changes, then continue through the Modify Threshold screens, making changes as necessary, until the summary screen displays the alert configuration. 7.
Installing and Configuring the Director 2/140 Test Remote Notification If the e-mail and one of the call-home notification features are enabled, set up the HAFM application to test these remote notification features. Because the features are configured at the HAFM application, call-home and e-mail notification are enabled for multiple directors.
Installing and Configuring the Director 2/140 Enable Embedded Web Server Use the following steps to enable EWS: 1. At the Hardware View page, choose Configure > Enable Web Server. Choosing Enable Web Server automatically places a check mark in the check box. 2. Choose Enable Web Server again to remove the check mark and disable the EWS interface. When disabled, remote users cannot access the interface. Enable Telnet Use the following steps to enable Telnet: 1.
Installing and Configuring the Director 2/140 Installation To install and enable this option, choose the Configure Feature Key option under the Product Manager’s Configure menu. Configuring the FICON Management Server Use this procedure to configure whether the host is the controlling manager. The optional FICON Management Server feature must be installed in order to perform this procedure. • Enable Management Server—Click this check box to add a check mark and enable the management server.
Installing and Configuring the Director 2/140 — If Active=Saved is enabled (check mark), the IPL and the active address configuration are maintained as identical configurations. If a new configuration is activated through the Configure Addresses - “Active” dialog box, that configuration becomes the IPL address configuration. — If Active=Saved is not enabled (no check mark), the IPL address configuration and the active configuration are not maintained as identical, and may be different configurations.
Installing and Configuring the Director 2/140 To configure FICON management server, use the following steps: 1. Choose Configure > Management Server from the Product Manager window. The Configure FICON Management Server dialog box displays, as shown in Figure 2–26. Figure 2–26: Configure FICON Management Server dialog box 2. Enable or disable the management server by clicking Enable Management Server check box. (To disable the management server, click the check box again to remove the check mark.) 3.
Installing and Configuring the Director 2/140 Open Systems Management Server The Open System Management Server (OSMS) is a keyed feature that allows host control and inband management of the director or switch through a management application that resides on an open-systems interconnection (OSI) device. This device is attached to a director or switch port. The device communicates with the switch or director through Fibre Channel common transport (FC-CT) protocol.
Installing and Configuring the Director 2/140 read-only access to configuration and connectivity parameters. Clicking the check box when it contains a check mark removes the check mark and allows a host program to change configuration and connectivity parameters on the director. 4. To activate changes and close the dialog box, click Activate. 5. If you are finished configuring the director, you can back up the configuration data.
Installing and Configuring the Director 2/140 • Because directors are bound to a fabric by world wide name (WWN) and domain ID, the Insistent Domain ID option in the Configure Switch Parameters dialog box is automatically enabled if Fabric Binding is enabled. You cannot disable Insistent Domain ID while Fabric Binding is active and the director is online. • If Fabric Binding is enabled and the director is online, you cannot disable Insistent Domain ID.
Installing and Configuring the Director 2/140 Notes • When the Switch Binding feature is first installed and has not been enabled, the Switch Membership List is empty. When you enable Switch Binding, the Membership List is populated with WWNs of devices, directors, or both that are currently connected to the director. • If the director is offline and you activate switch binding, the Membership List is not automatically populated.
Installing and Configuring the Director 2/140 3. Click one of the Connection Policy options. • Restrict E_Ports—Select if you want to restrict connections from specific directors to director E_Ports. Director WWNs can be added to the Switch Membership List to allow connection and removed from the Membership List to prohibit connection. Devices are allowed to connect to any F_Port. • Restrict F_Ports—Select if you want to restrict connections from specific devices to director F_Ports.
Installing and Configuring the Director 2/140 Figure 2–29: Switch Binding Membership List dialog box Refer to “Configuring Switch Binding—Overview” on page 2-54 for information on how the Switch Membership List is populated with WWNs according to options set in the Switch Binding State Change dialog box. 2. If nicknames are configured for WWNs through HAFM and you want these to display instead of WWNs in this dialog box, click Display Options. The Display Options dialog box displays. 3.
Installing and Configuring the Director 2/140 • Switch Binding is not enabled for the same port type as enabled for the Connection Policy in the Switch Binding State Change dialog box. For example, a WWN for a director attached to an E_Port can be removed if the Switch Binding Connection Policy was enabled to Restrict F_Ports. • The director or device with the WWN is connected to a port that is blocked. • The director or device with the WWN is not currently connected to the director (detached node).
Installing and Configuring the Director 2/140 • WWNs can only be removed from the Switch Membership List if any of the following are true: — The director or switch is offline. — Switch Binding is disabled. — The director or device with the WWN is not connected to the director or switch. — Switch Binding is not enabled for the same port type as enabled for the Connection Policy in the Switch Binding State Change dialog box.
Installing and Configuring the Director 2/140 Switch Binding This is a SANtegrity feature enabled through the Configure menu in the Product Manager that allows or prohibits switches and/or directors from connecting to director E_Ports, devices from connecting to F_Ports. Refer to “Enable/Disable and Online State Functions” on page 2-58 for details on enabling/disabling Switch Binding with Enterprise Fabric Mode enabled.
Installing and Configuring the Director 2/140 Insistent Domain Identification (ID) Insistent Domain Identification (ID) is a parameter in the Configure Switch Parameters dialog box, available from Configure menu in the Product Manager application. Enabling this option sets the domain ID configured in the Preferred Domain ID field in the Configure Switch Parameters dialog box as the active domain identification when the fabric initializes.
Installing and Configuring the Director 2/140 3. Verify that the R_A_TOV and E_D_TOV values for the director are identical to the values for all directors and switches participating in the fabric. 4. Route a multi-mode or single-mode fiber-optic cable (depending on the ISL distance between directors) between customer-specified E_Ports of both directors. 5. At the Products View page, click the Director 2/140 icon. The Hardware View page for the selected director displays. 6.
Installing and Configuring the Director 2/140 Figure 2–30: Port Properties dialog box Unpack, Inspect, and Install the Ethernet Hub (Optional) The HAFM server and one or more directors connect through an Ethernet hub installed on a 10/100 Mbps LAN segment. One hub port is required to connect the HAFM server, and one hub port is required to connect each director.
Installing and Configuring the Director 2/140 For instructions to unpack and inspect one or more Ethernet hubs, and install the hubs in a desktop or rack-mount configuration, refer to the appropriate Ethernet hub documentation. Using HAFM from a Remote Location Use this section to install the HAFM client on a remote workstation. Remote Workstation Minimum Requirements The following minimum requirements must be met in order to install HAFM on a remote workstation.
Installing and Configuring the Director 2/140 Install HAFM Client on a Remote Workstation Use these steps to install HAFM on a remote client: 1. Verify the workstation and the Ethernet LAN segment (with the Director 2/140 attached) are connected through the Internet. 2. At the workstation, launch the browser application. 3. At the browser, type the HAFM server IP address. 4. The HAFM splash screen displays with the following options, see Figure 2–31. a.
Installing and Configuring the Director 2/140 5. To install the remote client application, scroll down to the information that pertains to your platform, and follow the instructions provided. 6. After you have downloaded the installer executable, the InstallAnywhere Wizard displays. Follow the instructions provided to continue the installation. Launch HAFM from the Remote Client Use these steps to launch HAFM from a remote client: 1. Double-click the HAFM icon to launch HAFM.
3 Using EWS to Configure the Director 2/140 This chapter contains information on how to launch and configure the Embedded Web Server. The configuration portion defines specific Director 2/140 system settings, including: • Ports • Network addresses • Identification and contact information • Date and time • Operating parameters • SNMP settings • Passwords and user privileges. This chapter covers the initial set up of the Director 2/140.
Using EWS to Configure the Director 2/140 3. At the browser, enter the director IP address in the Uniform Resource Locator (URL) field. The Enter Network Password dialog box displays, as shown in Figure 3–1. 4. Type the default user name and password, or the user name and password assigned by the administrator. NOTE: The default user name is Administrator and the default password is password. The user name and password are case-sensitive. 5. Click OK.
Using EWS to Configure the Director 2/140 Figure 3–2: View page Configure Director Ports Use the following procedure to configure the names and settings for director Fibre Channel ports: 1. At the View page, choose the Configure option at the left side of the panel. The Ports page displays, as shown in Figure 3–3. Use the vertical scroll bar as necessary to display additional port information rows (up to 143 ports). a.
Using EWS to Configure the Director 2/140 Figure 3–3: Ports page c. Click the check box in the 10-100 km column to enable extended distance buffering for a port (the default is disabled). A check mark in the box enables extended distance operation up to 100 kilometers (through repeaters). 2. Scroll down to the bottom of the page and click Activate to save the information. The message “Your changes to the port configuration have been successfully activated” displays.
Using EWS to Configure the Director 2/140 Figure 3–4: Identification page a. Type a director name of 24 or fewer alphanumeric characters in the Name field. Configure each director with a unique name. If the director is installed on a public LAN, the name should reflect the director’s Ethernet network DNS host name. For example, if the DNS host name is SAN140.hp.com, the name entered in this dialog box is SAN140. b.
Using EWS to Configure the Director 2/140 Figure 3–5: Date/Time Properties page a. Click the Date fields that require change. Type changes using the following ranges: Month (MM): 1 through 12 Day (DD): 1 through 31 Year (YYYY): greater than 1980 b. Click the Time fields that require change. Type changes in the following ranges: Hour (HH): 0 through 23 Minute (MM): 0 through 59 Second (SS): 0 through 59 2. Click Activate to save the information.
Using EWS to Configure the Director 2/140 • E_D_TOV • Preferred Domain ID • Interop Mode • Switch Priority • Rerouting Delay First, set the director offline as follows. 1. At the View page, select the Operations option at the left side of the panel. The Operations page opens with the Port Beaconing page displayed. 2. At the Operations page, click the Online State tab. The Current State page displays, as shown in Figure 3–6. Figure 3–6: Current State page 3. Click Set Offline.
Using EWS to Configure the Director 2/140 Figure 3–7: Parameters page Ordinarily, you do not need to change values in this page from their defaults. The only exception is the Preferred Domain ID. Change this value if the director will participate in a multi-switch fabric. 6. Use information under “Switch Parameters” to change settings as required for parameters in this dialog box. 7. After you change settings, click the Activate button. 8. Return the director to online as follows. a.
Using EWS to Configure the Director 2/140 Switch Parameters Configure the following parameters as required by your fabric. Domain ID The domain identification is a value between 1 and 31 that provides a unique identification for the director in a fabric. A fabric director cannot contain the same domain ID as another director or their E_Ports will segment when they try to join.
Using EWS to Configure the Director 2/140 • This option is required if Enterprise Fabric Mode (optional SANtegrity binding feature) is enabled. • If you enable Insistent Domain while the switch or director is online, the Preferred Domain ID will change to the current active domain ID if the IDs are different. CAUTION: If a director with a duplicate domain ID exists in the fabric, both directors' E_Ports will segment when they try to join.
Using EWS to Configure the Director 2/140 Configure Fabric Operating Parameters Use procedures in this section to set parameters on the director for fabric operation through the Fabric Parameters page. These operating parameters are stored in NV-RAM on the director. First, set the director offline as follows. 1. At the View page, select the Operations option at the left side of the panel. The Operations page opens with the Port Beaconing page displayed. 2.
Using EWS to Configure the Director 2/140 Figure 3–9: Fabric Parameters page 6. Use information under “Fabric Parameters” to change settings as required for parameters in this dialog box. 7. After you change settings, click Activate. 8. Back up the configuration data when you are finished configuring the switch. 9. Return the director to online as follows. a. At the View page, select the Operations option at the left side of the panel. The Operations page opens with the Port Beaconing page displayed. b.
Using EWS to Configure the Director 2/140 Fabric Parameters Configure the following parameters as required by your fabric. BB_Credit Configure the director to support buffer-to-buffer credit (BB_Credit) from 1 through 60. This is the value used for all ports, except those configured for extended distance buffering (10-100 km). The default value is 16. For a description of the buffer-to-buffer credit, refer to the industry specification, Fibre Channel Physical and Signaling Interface.
Using EWS to Configure the Director 2/140 If all directors are set to Principal or Default, the director with the highest priority and the lowest WWN becomes the principal director. Following are some examples of principal director selection when directors have these settings: • If you have three directors and set all to Default, the director with the lowest WWN becomes the principal director.
Using EWS to Configure the Director 2/140 Configure Network Information Verify the type of LAN installation with the customer’s network administrator. If one director is installed on a dedicated LAN, network information (IP address, subnet mask, and gateway address) does not require change. If multiple directors are installed, or a public LAN segment is used, network information must be changed to conform to the customer’s LAN addressing scheme.
Using EWS to Configure the Director 2/140 3. Click Activate to save the information. The Activate message displays, as shown in Figure 3–11. Figure 3–11: Activate message box 4. Update the address resolution protocol (ARP) table as follows. a. Choose File > Close. The Windows desktop displays. b. At the Windows desktop, choose Start > Programs > Accessories > Command Prompt. A disk operating system (DOS) window displays. c. Delete the director’s old IP address from the ARP table.
Using EWS to Configure the Director 2/140 Configure SNMP Trap Message Recipients Use this procedure to configure community names, write authorizations, and network addresses for up to 6 SNMP trap message recipients. A trap recipient is a management workstation that receives notification (through SNMP) if a director event occurs. 1. Launch EWS. See “Launch EWS” on page 3–1. 2. If network information was configured at the browser, go to step 3.
Using EWS to Configure the Director 2/140 b. Click the check box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled). A check mark in the box indicates write authorization is enabled. When the feature is enabled, a management workstation user can change sysContact, sysName, and sysLocation SNMP variables. c. Type the IP address or DNS host name of the trap recipient (SNMP management workstation) in the associated Trap Recipient field.
Using EWS to Configure the Director 2/140 Configure User Rights Use this procedure to configure the administrator-level and operator-level passwords required to access EWS through the Username and Password Required page. 1. At the Configure page, click the User Rights tab. The User Rights page displays, as shown in Figure 3–13. Figure 3–13: User Rights page 2. For the Administrator set of data fields: a.
Using EWS to Configure the Director 2/140 b. Type the operator password (as specified by the customer’s network administrator) in the New Password field. Use 16 or fewer alphanumeric characters. c. Type the operator password again in the Confirm New Password field. 4. Click Activate to save the information. The message “Your changes to the user rights configuration have been successfully activated” displays. 5. Choose File > Close. The Windows desktop displays.
4 Manage Firmware Versions The Director 2/140 internal operating code is downloaded from the HAFM server and stored on a CTP card. Up to eight versions can be stored on the HAFM server hard drive and made available for download to a director.
Manage Firmware Versions Figure 4–1: Firmware Library dialog box 4. The firmware version displays at the lower left corner of the dialog box in XX.YY.ZZ format, where: • XX is the version level • YY is the release level • ZZ is the patch level 5. Click Close. Add a Firmware Version The firmware version shipped with the director is provided on the Director 2/140 documentation CD. Subsequent firmware versions to upgrade the director are provided to customers through the HP website.
Manage Firmware Versions NOTE: The following path is subject to change. a. At the HAFM server or other personal computer (PC) with Internet access, open the HP website. The uniform resource locator (URL) is http://thenew.hp.com/country/us/eng/support.html. b. Click on Firmware Downloads in left panel. c. Click the Director Firmware Version XX.YY.ZZ entry, where XX.YY.ZZ is the desired version. The Windows Save As dialog box displays.
Manage Firmware Versions Figure 4–2: New Firmware Version dialog box 6. Select the desired firmware version file (downloaded in step 1) from the HAFM server Zip drive, CD ROM drive, or hard drive. Verify that the correct directory path and filename display in the File name field and click Save. The New Firmware Description dialog box displays. See Figure 4–3. Figure 4–3: New Firmware Description dialog box 7. Enter a description (up to 24 characters in length) for the new firmware version and click OK.
Manage Firmware Versions 9. The new firmware version and associated description display in the Director Firmware Library dialog box. Click Close to close the dialog box and return to the Product Manager application. 10. To send the firmware version to a director, see “Download a Firmware Version to a Director” on page 4–6. Modify a Firmware Version Description Use these steps to modify the description of a director firmware version in the library stored on the HAFM server hard drive: 1.
Manage Firmware Versions Delete a Firmware Version Use these steps to delete a firmware version from the library stored on the HAFM server hard drive: 1. At the HAFM server, open the HAFM application. The Products View page displays. 2. Double-click the icon representing the director from which the firmware version will be deleted. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 4–1.
Manage Firmware Versions 2. Before downloading firmware version XX.YY.ZZ to a director, ensure the required, compatible version of the HAFM application is running on the HAFM server. Refer to the Release Notes that shipped with HAFM. a. Choose Help >About. The About dialog box displays and lists the HAFM application version. Click OK to close the dialog box. b. If required, install the correct version of the HAFM application. 3.
Manage Firmware Versions 6. Select the firmware version to be downloaded and click Send. The send function verifies existence of certain director conditions before the download process begins. If an error occurs, a message displays indicating the problem must be fixed before firmware is downloaded. Conditions that terminate the process include: • A redundant CTP card failure. • The firmware version is being installed to the director by another user. • The director-to-HAFM server link is down.
Manage Firmware Versions After the IPL, a “Synchronizing CTPs” message displays. This message remains as files are transmitted to the second CTP card and the progress bar travels across the dialog box to 100%. When the download reaches 100%, a “Send firmware complete” message displays. 8. Click Close to close the dialog box. 9. Click Close to close the Director Firmware Library dialog box and return to the Hardware View page.
A Regulatory Compliance Notices This appendix covers the following topics: • Regulatory Compliance ID Numbers, page A–1 • Federal Communications Commission Notice, page A–2 • Canadian Notice (Avis Canadien), page A–4 • European Union Notice, page A–4 • Japanese Notice, page A–5 • Taiwanese Notice, page A–5 • Laser Safety, page A–6 • Declaration of Conformity, page A–8 Regulatory Compliance ID Numbers For the purpose of regulatory compliance certifications and identification, your HP StorageW
Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Declaration of Conformity for Products Marked with FCC Logo—United States Only This device complies with Part 15 of the FCC Rules.
Regulatory Compliance Notices IEC EMC Statement (Worldwide) This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
Regulatory Compliance Notices • EN55024 1998 (IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-8, IEC61000-4-11)-Electromagnetic Immunity • EN60950 (IEC60950)-Product Safety • Power Quality: (IEC610000-3-2)-Harmonics and (IEC61000-3-3)-Voltage Fluctuations and Flicker • Also approved under UL 1950, 3rd Edition/CSA C22.2 No.
Regulatory Compliance Notices Harmonics Conformance (Japan) German Noise Declaration Schalldruckpegel Lp = 70.3 dB(A) Am Arbeitsplatz (operator position) Normaler Betrieb (normal operation) Nach ISO 7779:1988 / EN 27779:1991 (Typprüfung) Laser Safety WARNING: To reduce the risk of exposure to hazardous radiation: • Do not try to open the laser device enclosure. There are no user-serviceable components inside.
Regulatory Compliance Notices The OLM includes the following certifications: • UL Recognized Component (USA) • CSA Certified Component (Canada) • TUV Certified Component (European Union) • CB Certificate (Worldwide) The following figure shows the Class 1 information label that appears on the metal cover of the OLM housing.
Regulatory Compliance Notices Declaration of Conformity The Declaration of Conformity is shown on the next page.
B Technical Specifications This appendix contains the following information: • Physical Dimensions, page B–1 • Environmental Specifications, page B–2 • Power Requirements, page B–2 • Operating Tolerances, page B–3 • Laser Information, page B–3 Physical Dimensions Table B–1 lists Director 2/140 dimensions. Table B–1: Dimensions Dimension Size Height 52.7 cm (20.9 in) Width 44.1 cm (17.5 in) Depth 61.0 cm (24.2 in) Weight 75.9 kg (167 lb) Shipping Weight 102.
Technical Specifications Environmental Specifications Figure B–2 lists environmental ranges for shipping, storing, and operating the HP StorageWorks Director 2/140. Table B–2: Environmental Specifications Specification Shipping Storage Operating Weight 102.1 kg (225 lb) 75.9 kg (167 lb) 75.
Technical Specifications Operating Tolerances Table B–4 lists heating and cooling specifications, shock tolerances, vibration, acoustical noise and inclination. Table B–4: Operating Tolerances Specification Value Heat dissipation 842W (2,873 BTU/hr) Cooling airflow clearances Right and left sides: 2.5 cm (1.0 in) Front and rear: 7.6 cm (3.0 in) Top and bottom: No clearance required Shock and vibration tolerance 60 Gs for 10 milliseconds without nonrecoverable errors Acoustical noise 7.
Part Number 300834-B21 Short wave Transceivers on UPM Card 4 Short wave Wave Length 850 nm Media/Distance 50/125 µm multi-mode: 2 m–500 m 62.
C Electrostatic Discharge This appendix contains the following information: • Precautions Against Electrostatic Discharge • Grounding Methods Precautions Against Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Electrostatic Discharge • Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both feet when standing on conductive floors or dissipating floor mats. • Use conductive field service tools. • Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, have an HP authorized service provider install the part.
Glossary This glossary defines terms used in this guide or in other guides in this series, and is not a comprehensive glossary of computer terms. The following cross-references are used in this glossary: Contrast with. This refers to a term that has an opposite or substantively different meaning. See. This refers the reader to another keyword or phrase for the same term. See also. This refers the reader to additional information contained in another entry.
Glossary audit log Log summarizing actions (audit trail) made by the user. authentication Verification of identity for a person or process. backplane The backplane provides 48 VDC power distribution and connections for all logic cards. backup FRU When an active FRU fails, an identical backup FRU takes over operation automatically (failover) to maintain director and Fibre Channel link operation.
Glossary broadcast frames Data packet, also known as a broadcast packet, whose destination address specifies all computers on a network. See also multicast. buffer Storage area for data in transit. Buffers compensate for differences in processing speeds between devices. See also BB_Credit. CHPID See channel path identifier. call-home Product feature which enables the HAFM server to automatically contact a support center and report system problems.
Glossary Class 3 Fibre Channel service Provides a connectionless (not dedicated) service without notification of delivery or nondelivery between two N_Ports. Also known as datagram. community profile Information that specifies which management objects are available to what management domain or SNMP community name. concurrent maintenance Ability to perform maintenance tasks, such as removal or replacement of field-replaceable units, while a hardware product is operating.
Glossary cyclic redundancy check System of error checking performed at both the sending and receiving station using the value of a particular character generated by a cyclic algorithm. When the values generated at each station are identical, data integrity is confirmed. DASD Direct access storage device such as a disk drive. datagram See Class 3 Fibre Channel service. default Pertaining to an attribute, value, or option that is assumed when none is explicitly specified.
Glossary domain ID Number (1 through 31) that uniquely identifies a switch in a multi-switch fabric. A distinct domain ID is automatically allocated to each switch in the fabric by the principal switch. E_Port See expansion port. E_D_TOV See error-detect time-out value. Embedded Web Server Administrators or operators with a browser-capable PC and an Internet connection can monitor and manage the director through an Embedded Web Server interface.
Glossary explicit fabric login Data field size, supported by an F_Port, that is agreed upon during fabric login. fabric Entity that interconnects N_Ports and is capable of routing (switching) Fibre Channel frames using the destination ID information in the Fibre Channel frame header accompanying the frames. fabric element Any active director or node in a switched fabric. fabric port Physical interface within the fabric that connects to an N_Port through a point-to-point full duplex connection.
Glossary field-replaceable unit Assembly removed and replaced in its entirety when any one of its components fails. firmware Embedded program code that resides and executes on the director. FPM See fiber port module card. F_Port See fabric port. FRU See field-replaceable unit. gateway A multi-homed host used to route network traffic from one network to another, and to pass network traffic from one protocol to another. gateway address A unique string of numbers (in the format xxx.xxx.xxx.
Glossary high availability A performance feature characterized by hardware component redundancy (enabling non-disruptive maintenance). High-availability systems maximize system uptime while providing superior reliability, availability, and serviceability. hop Data transfer from one node to another node. homogeneous fabric A fabric consisting of only HP products. hop count The number of hops a unit of information traverses in a fabric.
Glossary Internet protocol address Unique string of numbers (in the format xxx.xxx.xxx.xxx) that identifies a device on a network. interoperability Ability to communicate, execute programs or transfer data between various functional units over a network. interswitch link Also known as ISL. Physical E_Port connection between two directors in a fabric. IOCDS A data set that contains an I/O configuration definition built by the IOCP. IP address See Internet protocol address.
Glossary logical unit number Also known as LUN. In Fibre Channel addressing, a logical unit number is a number assigned to a storage device which, in combination with the storage device’s node port’s world wide name, represents a unique identifier for a logical device on a storage area network. loopback plug In a fiber optic environment, a type of duplex connector used to wrap the optical output signal of a device directly to the optical input.
Glossary multi-switch fabric Fibre Channel fabric created by linking more than one director or fabric switching device within a fabric. name server Program that translates names from one form into another. Domain name servers (DNS) translate domain names into IP addresses. name server zoning N_Port access management that allows N_Ports to communicate if and only if they belong to a common name server zone. network address Name or address that identifies a managed product on a TCP/IP network.
Glossary • Online—when the director is set online, an attached device can log in to the director if the port is not blocked. Attached devices can communicate with each other if they are configured in the same zone. • Offline—when the director is set offline, all ports are set offline. The director transmits the offline sequence (OLS) to attached devices, and the devices cannot log in to the director.
Glossary password Unique string of characters known to the computer system and to a user who must specify it to gain full or limited access to a system and to the information stored within it. path In a network, any route between any two ports. persistent binding A form of server-level access control that uses configuration information to bind a server to a specific Fibre Channel storage volume (or logical device) using a unit number.
Glossary product name User-configurable identifier assigned to a managed product. Typically, this name is stored on the product itself. For the director, the product name can also be accessed by an SNMP manager as the system name. PSP bucket See preventive service planning bucket. R_A_TOV See resource allocation time-out value.
Glossary segmented E_Port E_Port that has ceased to function as an E_Port within a multi-switch fabric due to an incompatibility between the fabrics that it joins. See also expansion port. SEL System error light. serial crossbar assembly The serial crossbar assembly (SBAR) is responsible for Fibre Channel frame transmission from any director port to any other director port. Connections are established without software intervention. SNMP Simple network management protocol.
Glossary switch priority Value configured into each switch in a fabric that determines its relative likelihood of becoming the fabric’s principal switch. system services processor Controls the RS-232 maintenance port, the Ethernet port, and the operator panel of a Fibre Channel director. topology Logical and/or physical arrangement of stations on a network. trap Unsolicited notification of an event originating from a SNMP managed device and directed to an SNMP network management station.
Glossary warning message Indication that a possible error has been detected. See also error message and information message. wrap plug See loopback plug. world wide name Eight byte address that uniquely identifies a switch, or a node (end device), even on global networks. WWN See world wide name. zone Set of devices that can access one another. All connected devices may be configured into one or more zones. Devices in the same zone can see each other. Those devices that occupy different zones cannot.
Index 10/100 BaseT ethernet hub 1–1 A AC module 1–14 AC system harness 1–14 active=saved 2–49 AIX operating system 2–64 alerts, introduction 1–4 allen wrench, caution 1–15 asynchronous RS-232 null modem cable 1–16 audience xi B backing up director configuration file 4–9 beaconing LED 1–9 beaconing, introduction 1–5 C cables, FCC compliance statement A–3 call-home feature introduction 1–5 call-home feature, configuring 2–38 Canadian Notice (Avis Canadien) A–4 CE marking A–4 CFR, laser compliance 1–10 chan
Index degraded fabric performance, causes of 1–7 diagnostic software, introduction 1–4 dialog boxes configure fabric parameters 2–31, 3–11 configure feature key 2–24 configure FICON management server 2–51 configure open systems management server 2–52 configure switch parameters 2–27 switch binding membership list 2–56 director AC module 1–14 desktop, installing 2–7 e_d_tov 1–7 Fibre Channel addresses 2–29, 3–9 firmware 4–2 general description 1–1 management, overview 1–3 NV-RAM 2–27, 2–31, 3–11 r_a_tov 1–7
Index F f_ports 1–10 fabric binding 2–53 enterprise fabric mode 2–59 fabric parameters e_d_tov 2–32, 3–13 interop mode 2–33, 3–14 r_a_tov 2–32, 3–13 switch priority 2–33, 3–13 fabric segmentation e_d_tov 2–32, 3–13 preferred domain ID 2–29, 3–9 failover, SBAR assembly 1–14 FC fabric element MIB, version 1–5 FCC class A compliance notice A–2 class B compliance notice A–2 FCC compliance statement, cables A–3 feature SANtegrity 2–53 feature key 2–24 features of the director 2/140 1–8 Federal Communications Co
Index I inband switch management 2–30 input filter 1–14 insistent domain ID 2–29, 3–9 enterprise fabric mode 2–61 installation options 2–4 customer-supplied equipment rack 2–4 table or desk top 2–4 Installation Task Summary (table) 2–1 installation tasks backing-up configuration data 2–47 call-home feature, configuring 2–38 director unpacking, inspecting, installing 2–6 recording and verifying HAFM Server restoration information 2–17 summary 2–1 unpacking, inspecting, and installing Ethernet hub 2–63 Intel
Index gateway 2–10 IP address 2–9 MAC address 2–9 subnet mask 2–10 null modem cable 1–16 NV-RAM 2–27, 2–31, 3–11 O OFC class 1 laser transceivers 1–10 online state, setting 2–25 open fabric 1.
Index summary of installation tasks 2–1 SunOS operating system 2–64 switch error-detection, reporting, and serviceability features 1–4 multiswitch fabric 1–6 switch binding 2–54, 2–60 configuring 2–23 membership list 2–56 online state functions 2–58 zoning function 2–59 switch binding membership list dialog box 2–56 switch clock alert mode 2–49 switch clock alert mode field 2–51 switch parameters domain RSCNs 2–30, 3–10 insistent domain ID 2–29, 3–9 NV-RAM storage 2–27, 2–31, 3–11 operating mode 2–30 prefe
Index principal switch 2–33, 3–13 Z zoning joining, rules of 1–7 zone set, description of 1–6 director 2/140 installation guide Index–7
