installation guide hp StorageWorks director 2/64 Product Version: FW V05.01.00-24/HAFM SW V07.01.00-09 Third Edition (June 2003) Part Number: AA–RSNGC–TE/958–000289–001 This guide provides procedures for setting up, configuring, and managing the HP StorageWorks Director 2/64.
© Copyright 2001-2003 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
contents Contents About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents SBAR Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Module Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools Supplied with the Director . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents HAFM Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Enabling HAFM to Manage the Director. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Verify Communication Between the Director and HAFM Server. . . . . . . . . . . . . . . . . . 81 Set Director Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Set Date and Time Manually . . .
Contents Delete Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Remote Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Up HAFM Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Open Systems Management Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure FICON Management Server . . . . . .
Contents Harmonics Conformance (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . German Noise Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Certification and Classification Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 8 Preparing the front rack columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Preparing the rear rack columns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installing the rack mounting brackets on the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 View page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ports page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Identification page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date/Time Properties page. . . . . .
Contents 10 Director 2/64 Installation Guide
about this guide About this Guide This guide provides information on installing, configuring, managing, and verifying operation of the HP StorageWorks Director 2/64. The Director 2/64 About this Guide switch connects storage devices, hosts, and servers in a SAN. The director is easily managed and configured to optimize the performance of your SAN.
About this Guide Overview This section covers the following topics: ■ Intended Audience ■ Related Documentation Intended Audience This guide is part of a documentation set that supports the Director 2/64. It is intended for use by trained service and installation representatives experienced with the SAN technology and Fibre Channel technology.
About this Guide Conventions Conventions consist of the following: ■ Document Conventions ■ Text Symbols ■ Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases.
About this Guide Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment Symbols The following equipment symbols may be found on hardware for which this guide pertains. They have the following meanings.
About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
About this Guide Rack Stability Rack stability protects personnel and equipment. WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: ■ The leveling jacks are extended to the floor. ■ The full weight of the rack rests on the leveling jacks. ■ In single rack installations, the stabilizing feet are attached to the rack. ■ In multiple rack installations, the racks are coupled. ■ Only one rack component is extended at any time.
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support Telephone numbers for worldwide technical support are listed on the following HP website: http://www.hp.com/support/. From this website, select the country of origin. Note: For continuous quality improvement, calls may be recorded or monitored.
About this Guide 18 Director 2/64 Installation Guide
1 Overview 1 This chapter contains the following HP StorageWorks Director 2/64 information: ■ Director Description, page 20 ■ Features, page 21 ■ Hardware Components, page 27 ■ Tools and Test Equipment, page 34 ■ Optional Kits, page 37 Director 2/64 Installation Guide 19
Overview Director Description The director is a second-generation, 64-port product that provides dynamic switched connections between Fibre Channel servers and devices in a SAN environment. Directors are managed and controlled through a HAFM server with the High Availability Fabric Manager (HAFM) and Director 2/64 Product Manager applications installed. The HAFM server is a notebook personal computer (PC) that provides a central point of control for up to 48 directors and/or edge switches.
Overview Features Features of the Director 2/64 include: ■ Scalable from 32 to 64 User ports (with optional UPM 2 Gb add-on) ■ 100% dynamic non-blocking, cut through switching with congestion queuing ■ Online error detection, error isolation, and error recovery ■ Redundant, hot-pluggable components ■ Full duplex 200 MB/sec per port performance ■ Less than 2-µs average switch latency ■ 100-km distance support (60 buffers), with use of repeaters ■ Small form factor, hot-pluggable optical trans
Overview from a remote PC by entering the director’s IP address as the internet URL, then entering a user name and password at a login screen. The PC browser then becomes a management console. Note: The default user name for the right to view status and other information is “operator.” The default user name for the right to modify configuration data, perform maintenance tasks, or perform other options is “administrator.” The default password for both user names is “password.
Overview ■ Automatic notification of significant system events (to support personnel or administrators) through e-mail messages or the call-home feature at the HAFM server. ■ An RS-232 maintenance port at the rear of the director (port access is password-protected) that enables installation or service personnel to change the director’s internet protocol (IP) address, subnet mask, and gateway address.
Overview Product Manager application on the HAFM server to receive unsolicited SNMP trap messages. The trap messages indicate operational state changes and failure conditions. Note: For more information about SNMP support provided by HP products, refer to the HP StorageWorks SNMP Reference Guide for Directors and Edge Switches. Zoning The director supports a name server zoning feature that partitions attached devices into restricted-access groups called zones.
Overview Multi-Switch Fabrics A Fibre Channel topology that consists of one or more interconnected directors or switch elements is called a fabric. Operational software provides the ability to interconnect directors (through expansion port (E_Port) connections) to form a multi-switch fabric. The data transmission path through the fabric is typically determined by fabric elements and is user-transparent.
Overview ■ Port segmentation—When an ISL activates, directors exchange operating parameters to determine if they are compatible and can join to form a single fabric. If they are incompatible, the connecting E_Port at each director segments to prevent the creation of a single fabric. A segmented link transmits only Class F traffic; the link does not transmit Class 2 or Class 3 traffic.
Overview Hardware Components The Director provides a modular design that enables quick removal and replacement of FRUs. The following sections define Director 2/64 main components. Front View Figure 1 shows Director 2/64 components accessible from the front of the Director. Component descriptions follow the figure. 1 2 3 Power and system error LEDs UPM cards Power supplies 1. 4 5 6 Cable management assembly1 Front bezel CTP2 cards Provided in rack mount kits 9000/10000/11000 and M-Series only.
Overview CTP2 Card The Director 2/64 ships with two Control Processor (CTP2) cards. The active CTP2 card initializes and configures the director after power on, and contains the microprocessor and associated logic that coordinate director operation. The second CTP2 card serves as a backup. A CTP2 card provides an Initial Machine Load (IML) button on the faceplate.
Overview Cable Management Assembly The cable management assembly positioned at the front of the director provides routing for Ethernet cables attached to CTP2 cards and fiber-optic cables attached to director ports. The assembly rotates up to provide front access to the redundant power supplies. The cable management assembly is supplied with rack mount kits for the 9000/10000/11000 and M-Series racks only.
Overview Depending on device connections, G_Ports work as follows: ■ If the G_Port is attached to a Fibre Channel device, the port functions as a fabric port (F_Port). An F_Port is the interface on a director that connects to a device N_Port. ■ If the G_Port is attached to another director to form an Interswitch Link (ISL), the port functions as an expansion port (E_Port). A multi-switch fabric is formed through multiple directors and ISLs. Figure 2 shows the faceplate of an UPM.
Overview Single-mode or multi-mode fiber-optic cables attach to UPM cards through small form factor pluggable (SFP) optic transceivers. The fiber-optic transceivers provide duplex connectors, and can be detached from UPM cards (through a 10-pin interface) for easy replacement. Three fiber-optic transceiver types are available: ■ Short-wave Laser—Short-wave laser transceivers provide connections for transferring data over short distances (2 to 500 meters) through 50-µm (500 meters) or 62.
Overview 3 2 1 SHR-2309 1 2 Power module assembly SBAR assemblies 3 Fan modules Figure 3: Director components—rear Fan Modules Two fan modules, each containing three fans (six fans total), provide cooling for director FRUs, as well as providing redundancy for continued operation if a fan fails. The fan module can be replaced while the director is powered on and operating, provided the module is replaced within 10 minutes (after which software powers off the director).
Overview established, and establishes the connection if the destination port is available. The assembly also stores busy, source connection, and error status for each director port. The backup SBAR takes over operation if the active assembly fails, and provides the ability to maintain connectivity and data frame transmission without interruption. The transition to the backup assembly is transparent to attached devices.
Overview Tools and Test Equipment This section describes tools and test equipment that may be required to test, service, and verify operation of the director and attached HAFM server. These tools are either supplied with the director or must be supplied by service personnel. Tools Supplied with the Director The following tools are supplied with the director. Use of the tools may be required to perform test, installation, service, or verification tasks.
Overview Figure 5: Loopback plug ■ Fiber-optic protective plug—For safety and port transceiver protection, fiber-optic protective plugs, as shown in Figure 6, must be inserted in all director ports without fiber-optic cables attached. The director is shipped with protective plugs installed in all ports.
Overview Figure 7: Null modem cable Tools Supplied by Service Personnel The following tools are expected to be supplied by service personnel performing director installation or maintenance actions. Use of the tools may be required to perform one or more test, service, or verification tasks. ■ Scissors or pocket knife—A sharp cutting edge (scissors or knife blade) may be required to cut the protective strapping when unpacking replacement FRUs.
Overview Optional Kits Contact your Hewlett-Packard authorized service provider to purchase the following optional Director 2/64 kits. See Table 2 for descriptions of Director 2/64 optional kits. Table 2: Director 2/64 Optional Kits Supporting Kit Description HP Open Trunking License. Part Number: 336002-B21 Provides a license to use Open Trunking feature. HP SANtegrity Binding License. Part Number: 317073-B21 Provides a license to use SANtegrity Binding feature.
Overview 38 Director 2/64 Installation Guide
Installing and Configuring the Director 2/64 2 2 This chapter describes tasks to install, configure, and verify operation of the Director 2/64.
Installing and Configuring the Director 2/64 Installation Options The director is installed in one of two configurations. The options are: 40 ■ Table or desk top—One or more directors and an optional HAFM server are delivered and installed at the customer facility on a desk or table top. Ethernet cabling distance and local area network (LAN) addressing issues must be considered.
Installing and Configuring the Director 2/64 Review Installation Requirements The Director is delivered stand-alone and ready to be mounted in a HP 9000, HP 10000, HP 11000, HP M-Series, HP system/e, or industry-standard 19-in rack. Ethernet cabling, distance, and LAN addressing issues must be considered. Review the following checklist before installing the switch: ■ Prepare a site plan. Consult the HP StorageWorks SAN High Availability Planning Guide.
Installing and Configuring the Director 2/64 — A minimum depth of 24.5 in. — 19 in wide. — A minimum opening size of 10U available (9U for the director and 1U for the rail tray kit). ■ Two power outlets or different branches (for redundancy). ■ Torque driver with cross-tip bit (for setting 22 in/lb. of torque). ■ Fiber-optic protective plug—For safety and port transceiver protection, fiber-optic protective plugs must be inserted in all director ports without fiber-optic cables attached.
Installing and Configuring the Director 2/64 Select an Operating Location Install the director in a secure or limited-access area to ensure that cable connections are not compromised. Also, make sure to install the director in an area with the necessary ventilation and power requirements. Cooling and Power Requirements Two fan modules, each containing three fans (six fans total), provide cooling and redundancy fans for the director.
Installing and Configuring the Director 2/64 Unpack and Inspect the Director Unpack and inspect the director as follows: 1. Inspect the shipping container for damage caused during transit. 2. Unpack the shipping cartons. WARNING: The Director 2/64 weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. 3.
Installing and Configuring the Director 2/64 s.
Installing and Configuring the Director 2/64 Table 3: Shipping Carton Contents for an HP 9000/10000/11000 Rack Number Item 1 One HP StorageWorks Director 2/64 Product CD containing firmware, license, documentation 2 HP StorageWorks Director 2/64 Installation Guide 3 Two Power Distribution Unit (PDU) power cords 4 Two standard AC power cords 5 Four multi-mode, short-wave loopback plugs 6 One torque driver with integrated 5/32” bit 7 One 10-foot null modem cable 8 HP 9000/10000/11000 Rack Mo
Installing and Configuring the Director 2/64 s.
Installing and Configuring the Director 2/64 Table 4: Parts for Installing in a HP System/e and Industry-Standard 19-in Rack Label Item 1 HP StorageWorks Director 2/64 (part number: A6534-62001) 4 Rail Tray Kit (part number: A6534-60016): ■ ■ ■ ■ 2, 3, 5 One rail tray Two mounting brackets Two M3 Tinnerman nuts Four Torx T25 16 mm M5 SEM screws Mounting hardware: ■ Rack mount brackets (part number: A6534-60014) containing: Two front mounting brackets (5) ■ Two rear mounting plates (2) ■ Two rear a
Installing and Configuring the Director 2/64 Install the Director in a Rack The following sections provide instructions for installing the Director 2/64 in either the 9000/10000/11000 rack or in the HP system/e and industry-standard 19-in racks. If you plan to install the director in the optional M-Series Rack, refer to the HP StorageWorks M-Series Rack Mount Kit Installation Instructions.
Installing and Configuring the Director 2/64 WARNING: The Director 2/64 weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. Two people will need to work together to transfer the director to the lift. Make sure the wheels of the lift cannot roll as you transfer the director to the lift. Move the director slowly and carefully onto the lift to prevent back and hand injury.
Installing and Configuring the Director 2/64 3. Locate the square opening in the rail that corresponds with the appropriate marker hole, as shown in Figure 10. 4. Position the higher, shelf bracket threaded hole in this square opening, as shown in Figure 10. 5. Orient the shelf bracket in the rails. 6. Place the square washer provided on the front of the rail so that the two bumps on the washer sit in opposite corners in the rail’s square hole. 7.
Installing and Configuring the Director 2/64 1 2 3 4 SHR-2265B 1 2 Marker hole Square opening in rail 3 4 Screws with captive lock and flat washers Square alignment washers Figure 10: Securing shelf brackets Secure the Mounting Hardware Use these steps to secure the mounting hardware to the switch. 1. Locate the two front mounting brackets in the shipping carton. 2. Secure the front mounting brackets on either side of the switch, as shown in Figure 11.
Installing and Configuring the Director 2/64 Figure 11: Securing the two mounting brackets 3. Using a torque driver, torque the screws to 22 in/lb. 4. Locate the two rear mounting plates in the shipping carton. 5. Secure the two rear mounting plates to each side of the switch, as shown in Figure 11. For each plate, use the two flathead countersunk Phillips screws (10-32 x 0.25 in) provided. 6. Using a torque driver, torque the screws to 22 in/lb.
Installing and Configuring the Director 2/64 3. Count up 5 square openings from the cage nut you just installed, and insert the next cage nut. 4. Count up four square openings and install the third cage nut. 5. Repeat this procedure to install cage nuts in the corresponding front rail. Insert the Rear Cage Nuts in the Rack Use these steps to insert the four supplied cage nuts in the rack’s rear rails: 1. Select one of the rear rails. 2.
Installing and Configuring the Director 2/64 Figure 12: Aligning the switch in the rack 3. Loosely attach the rear angle bracket to the rack rail with the two panhead Phillips screws provided, as shown in Figure 13. 4. Repeat step 2 and step 3 for the corresponding rear angle bracket, as shown in Figure 13. 5. The two rear angle brackets now touch the outside surfaces of the rear mounting plates. Slide the switch all the way into the rack to where the front mounting bracket meets the rack rails. 6.
Installing and Configuring the Director 2/64 Figure 13: Securing the rear angle brackets 7. Using a torque driver, torque the screws to 22 in/lb. 8. Connect the remaining ends of the PDU power cords to separate PDUs (if installed), as shown in Figure 14; otherwise, connect the two standard AC power cords. Note: Hewlett-Packard recommends installing an optional PDU in the rack. Hewlett-Packard ships two PDU power cords with the Director 2/64.
Installing and Configuring the Director 2/64 9. Connect the equipment rack power cords to separate (for redundancy) facility power sources, providing single-phase, 120 to 240 VAC current.
Installing and Configuring the Director 2/64 3. Lower the rack feet (2) until they touch the floor. Figure 15: Mounting anti-tip feet for a HP system/e rack Install Mounting Bracket Hardware in the Rack Use these steps to install the mounting hardware in a rack. Note: The 9Us used to mount the switch are called U1 through U9; U1 is the lowest of the 9Us. Note also that 1U below the switch is required for the rail tray for a total of 10U to mount the switch. 1.
Installing and Configuring the Director 2/64 Figure 16: Rail tray mounting location requirement 4. Position and attach both rear brackets, as shown in Figure 17: a. Locate the lowest U of the 9Us chosen for mounting the switch (the lowest being U1). b. Attach each rear rail tray bracket to the rear rack uprights at U1 (one on the left and one on the right. c. Secure each rail tray bracket using one M5 Torx screw.
Installing and Configuring the Director 2/64 3 1 2 3 Rear tray bracket M5 screw with attached lock washer HP rack 1 2 Figure 17: Attaching a rear rail tray bracket 5. Install a Tinnerman nut in the top holes of U1 for both the left and right rack-front uprights, as shown in Figure 18.
Installing and Configuring the Director 2/64 6. Position the rail tray, as shown in Figure 19 and insert the tray into the rack from the front. Note: Make sure the slots in the sides of the rail tray slide over the posts on the rear rail tray brackets, and the posts on the rail tray’s front mounting flanges are inserted into the center holes of U1. Figure 19: Inserting the rail tray in the rack 7. Secure the rail tray: a.
Installing and Configuring the Director 2/64 Prepare the Front and Rear Rack Columns Use the following procedure to prepare the rack for installing a switch: 1. Prepare the front rack columns, as shown in Figure 20: a. Standing at the front of the rack, count up from the top of the rail tray (1) to the 13th, 19th, and 23rd holes on the rack's front face. b. Slide a sheet metal nut (2) on each of the located holes. Note: Three sheet metal nuts should be on each front column face (3).
Installing and Configuring the Director 2/64 Note: Two sheet metal nuts should be on each back column face (3). Figure 21: Preparing the rear rack columns Prepare the Switch for Installation The following section describes how to install the mounting hardware that attaches the switch to the rails.
Installing and Configuring the Director 2/64 3. Attach the bracket with 10-32, flat-head Phillips screws (4) using the two center threaded holes on the front side of the switch. 4. Repeat step 2 and step 3 for the second front mounting bracket. Figure 22: Installing the rack mounting brackets on the switch 5. Locate the two rear mounting brackets in the shipping carton. 6.
Installing and Configuring the Director 2/64 Finalize the Rack Mounting Procedure Use the following sections to complete the installation procedure. After completing the steps outlined in the previous sections, install the switch in the rack as follows. WARNING: The Director 2/64 weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. 1.
Installing and Configuring the Director 2/64 2. Mount the switch in the rack, as shown in Figure 24: a. On one side at the back of the switch, position an angle bracket (2) so that the threaded holes (1) are against the slots (5) of the rear mounting bracket and the angled side face out. b. Insert the screws (6) through the rear mounting bracket slots into the threaded nuts of the angle bracket. c.
Installing and Configuring the Director 2/64 3. Connect the other ends of the PDU power cords to separate PDUs (if installed), as shown in Figure 25; otherwise, connect the two standard AC power cords. Note: Hewlett-Packard recommends installing an optional PDU in the rack. Hewlett-Packard ships two PDU power cords with the Director 2/64. Figure 25: AC power connections WARNING: Hewlett-Packard power cords are provided for each director power supply.
Installing and Configuring the Director 2/64 Figure 26: Installing the sliding shelf brackets 6. Insert the shelf into the rack so that both rail rear slots (1) slide over the loose screws (2) on the inside face of each bracket, as shown in Figure 27.
Installing and Configuring the Director 2/64 Figure 27: Positioning the sliding shelf bracket on a rail rear slot 7. Make sure that the sliding shelf and rails are horizontal, as shown in Figure 28 at the rack front. 8. Push each of the rail front tabs (1) into the corresponding holes on the rack columns (2). 9. At the back of the rack, tighten the screws that attach the sliding shelf rails to the mounting brackets, as shown in Figure 27 (2).
Installing and Configuring the Director 2/64 Figure 28: Positioning the sliding shelf bracket at the rack front Recommended Cable Management Perform the following procedure after installing a switch, as shown in Figure 29: 1. Install two cable restraints (1) on each side of the rack in positions that will hold the Fibre Channel cables away from the power supply. 2. Form loose bundles of the installed Fibre Channel cables (2) on each side of the rack. 3.
Installing and Configuring the Director 2/64 Figure 29: Recommended cable management Power-On Self Test Use the following steps to run a Power-On Self Test (POST): 1. Power on the PDUs (if used). 2. At the bottom rear of the director, set the power switch (circuit breaker) to the Up position. The director powers on. The following occurs during POST: ■ Amber LEDs on both CTP2 cards and all universal port module (UPM) cards illuminate momentarily.
Installing and Configuring the Director 2/64 3. After successful POST completion, the green power LED on the front bezel, green LED on the active CTP2 card, and green PWR OK LEDs on both power supplies remain ON. 4. If a POST error or other malfunction occurs, refer to the HP StorageWorks Director 2/64 Service Manual.
Installing and Configuring the Director 2/64 Configure Director Network Information Use the following sections to configure the director’s network addressing scheme. Default Settings The director is delivered with the following default network addresses: ■ MAC address—The Media Access Control (MAC) address is programmed into FLASH memory on the CTP2 card at the time of manufacture. The address is in xx.xx.xx.xx.xx.xx format, where xx is a hexadecimal pair.
Installing and Configuring the Director 2/64 — Microsoft Windows 98, Windows 2000, Windows XP, or Windows NT 4.0 operating system — RS-232 serial communication software (for example, ProComm Plus or HyperTerminal) Note that the HAFM server may be used for this function and that HyperTerminal is included in Windows 2000 provided in the HAFM server.
Installing and Configuring the Director 2/64 1 2 Maintenance port RS-232 port 3 Null Modem cable Figure 30: Connecting the null modem cable between the director and a workstation 2. Connect the 9-pin end of the RS-232 modem cable to the maintenance port. 3. Connect the other cable end to a 9-pin communication port (COM1 or COM2) at the rear of the local workstation.
Installing and Configuring the Director 2/64 4. Choose Start > Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box displays, as shown in Figure 31. Figure 31: Connection Description dialog box 5. Type 264 in the Name field and click OK. The Connect To dialog box displays, as shown in Figure 32. Figure 32: Connect To dialog box 6.
Installing and Configuring the Director 2/64 Figure 33: COMn Properties dialog box 7. Configure the Port Settings parameters as follows: ■ Bits per second: 115200 ■ Data bits: 8 ■ Parity: None ■ Stop bits: 1 ■ Flow control: Hardware 8. Click OK. The HyperTerminal window displays. 9. At the > prompt, type the user-level password (the default is password) and press the Enter key. The password is case-sensitive. The HyperTerminal window displays with a C> prompt at the top of the window. 10.
Installing and Configuring the Director 2/64 Figure 34: HyperTerminal dialog box 11. To change director network addresses, type the following at the C> prompt and press Enter. ipconfig xxx.xxx.xxx.xxx.yyy.yyy.yyy.yyy.zzz.zzz.zzz.zzz The IP address format is xxx.xxx.xxx.xxx. The subnet mask format is yyy.yyy.yyy.yyy. The gateway address format is zzz.zzz.zzz.zzz. The octets xxx, yyy, and zzz are decimals from 0 through 255.
Installing and Configuring the Director 2/64 LAN-Connect the Director Use these steps to connect the rack mounted director to the Ethernet LAN segment. 1. Connect one end of an Ethernet cable to the RJ-45 connector on each CTP2 card, as shown in Figure 35. 1 2 Remote workstation Ethernet hub or switch (customer supplied) 3 4 HAFM server (laptop or rack mount) Director 2/64 Figure 35: LAN-connect the director 2.
Installing and Configuring the Director 2/64 HAFM Server To run HAFM software, you must set up and configure the HAFM server. Refer to the HAFM server installation guide for instructions on: ■ Setting up the HAFM server. ■ Connecting the HAFM server to the LAN. ■ Configuring the network addressing for the HAFM server. ■ Setting HAFM server date and time. ■ Creating HAFM user names and passwords.
Installing and Configuring the Director 2/64 Verify Communication Between the Director and HAFM Server Follow these steps to check director-to-server communication: 1. From the Products View page (as shown in Figure 37), take note of the shape and color of the symbol behind the director icon. Table 5 explains these symbols.
Installing and Configuring the Director 2/64 Table 5: Director Operational States and Symbols (Continued) Operational State Symbol Failed—Director-to-server communication has been established, but the director failed and requires immediate service. Go to step 2. Status Unknown—The director status is unknown because of a network communication failure between the director and HAFM server. Go to step 2. 2. Double-click the Director 64 icon.
Installing and Configuring the Director 2/64 Figure 38: Hardware View page (with FRU failures) Set Director Date and Time The Director 2/64 Product Manager log entries are stamped with the date and time received from the director. Use these steps to set the effective date and time for the director: Note: The director and HAFM synchronize at least once daily. 1. At the Hardware View page for the selected director, click the Configure menu. 2. Choose Date/Time from the drop-down menu.
Installing and Configuring the Director 2/64 3. Set director date and time manually, or set for periodic updates. For specific instructions, see the following sections: ■ Set Director Date and Time, page 83 ■ Synchronize Date and Time, page 85 Figure 39: Configure Date and Time dialog box Set Date and Time Manually Use these steps to set the director date and time manually: 1.
Installing and Configuring the Director 2/64 Synchronize Date and Time Use these steps to set the director to periodically synchronize date and time with HAFM: 1. At the Configure Date and Time dialog box, choose the Periodic Date/Time Synchronization check box. The Date and Time fields are grayed-out and not selectable. 2. Click Activate to enable synchronization and close the Configure Date and Time dialog box.
Installing and Configuring the Director 2/64 Frequently Used HAFM Settings This section summarizes the most common HAFM tasks including: Note: For a complete reference on HAFM functionality, refer to the HP StorageWorks HA-Fabric Manager User Guide.
Installing and Configuring the Director 2/64 Set the Director Online When the director is set online, an attached device can log into the director if the port is not blocked. Attached devices can communicate with each other if they are configured in the same zone. Use these steps to set the director online: 1. Open HAFM. The Products View page displays. 2. Double-click the appropriate director icon. The Hardware View page for the selected director displays. 3. Choose Maintenance > Set Online State.
Installing and Configuring the Director 2/64 Follow these steps to configure the director identification: 1. At the Hardware View page, choose Configure > Identification. The Configure Identification dialog box displays, as shown in Figure 40. Figure 40: Configure Identification dialog box a. Type a director name of 24 or fewer alphanumeric characters in the Name field. Each director should be configured with a unique name.
Installing and Configuring the Director 2/64 the director is set to FICON management style, and FICON devices can communicate with each other if the director is set to open systems management style. Note: If the FICON management server feature is enabled, the default management style is FICON. Open systems management style cannot be enabled. To configure the director management style: 1. Ensure the director is set offline. For instructions, see “Set the Director Offline” on page 87. 2.
Installing and Configuring the Director 2/64 Caution: Setting the director offline terminates all Fibre Channel connections. 2. Choose Configure > Operating Parameters > Switch Parameters. The Configure Switch Parameters dialog box displays, as shown in Figure 41. Figure 41: Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID.
Installing and Configuring the Director 2/64 Preferred Note: To change this value, you must first set the director offline. Choose Set Online State from the Maintenance menu to display the Set Online State dialog box, then click Set Offline. Be sure to set the director back online after you change this value. Use this field to set a unique domain ID for the director. The default value is 1. Set a value between 1 and 31.
Installing and Configuring the Director 2/64 Rerouting Delay Placing a check mark in the check box to the left of the Rerouting Delay option enables rerouting delay. This option is only applicable if the configured director is in a multi-switch fabric. The default state is enabled. Enabling the rerouting delay ensures that frames are delivered in order through the fabric to their destination.
Installing and Configuring the Director 2/64 This option is enabled (check box not selected) by default. In most cases this option should be enabled so that attached devices can receive notification of zoning changes in the fabric. However, some HBAs may log out, then log back into the fabric when they receive an RSCN, thereby disrupting Fibre Channel traffic.
Installing and Configuring the Director 2/64 Figure 42: Configure Fabric Parameters dialog box 3. Use information under “Fabric Parameters” to change settings as required for parameters in this dialog box. 4. After you change settings, click the Activate button. 5. Back up the configuration data when you are finished configuring the switch. 6. Set the director online. For instructions, see “Set the Director Online” on page 87.
Installing and Configuring the Director 2/64 Note: Set the same value for R_A_TOV on all directors and edge switches in a multi-switch fabric. If the value is not the same on all units, the fabric segments. Also, the value for R_A_TOV must be greater than the value configured for E_D_TOV. E_D_TOV Adjust the E_D_TOV in tenth-of-a-second increments. An error condition occurs when an expected response is not received within the time limit set by this value. The default value is 20 tenths (2 seconds).
Installing and Configuring the Director 2/64 At least one director in a multi-switch fabric needs to be set as Principal or Default. If all of the directors are set to Never Principal, all of the interswitch links (ISLs) will segment. If all but one director is set to Never Principal and the director that was principal goes offline, then all of the other ISLs will segment. Note: We recommend you leave the switch priority setting as Default.
Installing and Configuring the Director 2/64 Interop Mode Choose one of the following options: ■ Homogeneous Fabric—Choose this mode if the fabric contains only HP directors and edge switches that are operating in Homogeneous Fabric mode. ■ Open Fabric 1.0—Default. Choose this mode if the fabric contains HP directors and edge switches, as well as other open-fabric compliant switches. Choose this mode for managing heterogeneous fabrics.
Installing and Configuring the Director 2/64 Figure 43: Configure Ports check boxes c. Click the 10-100 km check box to enable extended distance buffering for a port. A check mark in the box indicates the extended distance operation up to 100 kilometers (through repeaters) is enabled. d. Click the LIN Alerts check box to enable or disable LIN alerts for a port. A check mark in the box indicates alerts are enabled.
Installing and Configuring the Director 2/64 g. Click the Port Binding check box to enable WWN binding for the port, which allows only a specific device to attach to the port. This device is specified by the WWN or nickname entered into the Bound WWN column. With the check box cleared, any device can attach to the port even if a WWN or nickname is specified in the Bound WWN column. h. In the Bound WWN field, enter a world wide name (WWN) in the correct format (xx.xx.xx.xx.xx.xx.xx.
Installing and Configuring the Director 2/64 Figure 44: Configure SNMP dialog box a. For each trap recipient to be configured, type a community name of 32 or fewer alphanumeric characters in the associated Community Name field. The community name is incorporated in SNMP trap messages to ensure against unauthorized viewing or use. b. Click the check box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled).
Installing and Configuring the Director 2/64 Configure and Enable E-mail Notification Use this procedure to configure and enable e-mail addresses and Simple Mail Transfer Protocol (SMTP) server addresses to receive e-mail notification of director (and other managed product) events. The addresses must be configured via HAFM, then enabled. See “Test Remote Notification” on page 109. Use these steps to configure and enable e-mail and SMTP server addresses: 1.
Installing and Configuring the Director 2/64 5. Choose Maintenance > Enable E-Mail Notification. A check mark displays in the check box to indicate that e-mail notification for the director is enabled. Configure and Enable Call-Home Features There are two call-home features available, and only one is installed when the HAFM application is installed on the HAFM server. To learn more about configuring Call-Home features, refer to the HP StorageWorks HAFM server installation guide.
Installing and Configuring the Director 2/64 ■ A yellow triangle that displays by the Threshold Alerts field in the Port Properties dialog box. ■ Detailed threshold alert data recorded in the Threshold Alert Log. Use the Threshold Alerts option on the Configure menu to configure the following: ■ Name for the alert. ■ Type of threshold for the alert (Rx, Tx, or either). ■ Active or inactive state of the alert.
Installing and Configuring the Director 2/64 Figure 47: Configure Threshold Alerts dialog box 2. Click New. The New Threshold Alert dialog box displays, as shown in Figure 48. Figure 48: New Threshold Alerts dialog box—first screen 3. Enter a name from one to 64 characters in length. All characters in the ISO Latin-1 character set, excluding control characters, are allowed. 4.
Installing and Configuring the Director 2/64 ■ Tx Throughput—An alert will occur if the threshold set for transmit throughput is reached. ■ Rx or Tx Throughput—An alert will occur if the threshold set for either receive or transmit throughput is reached. 5. Click Next. A new screen displays with additional parameters, as shown in Figure 49. The name configured for the alert displays at the top of the screen. Note: Click Previous if you need to return to the previous screen.
Installing and Configuring the Director 2/64 9. Click Next. A new screen displays for selecting ports for the alerts, as shown in Figure 50. Figure 50: New Threshold Alerts dialog box—third screen 10. Choose either Port Type or Port List. ■ For Port Type, choosing either E_Ports or F_Ports will cause this alert to generate for all ports configured as E_Ports or F_Ports, respectively. ■ For Port List, you can choose individual ports by clicking the check box by each port number or set all ports.
Installing and Configuring the Director 2/64 Figure 51: New Threshold Alerts dialog box—summary screen 12. Click Finish. The Configure Threshold Alerts dialog box displays listing the name, type, and state of the alert that you just configured. 13. At this point, the alert is not active. To activate the alert, choose the alert information that displays in the Configure Threshold Alerts table and click Activate. The alert is activated, as shown in Figure 52.
Installing and Configuring the Director 2/64 Modify Alerts Use the following steps to modify an existing threshold alert configuration. 1. At the Hardware View page, choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays. Choose the alert that you want to modify by clicking the alert information in the table. If the alert is active, an error message displays prompting you to deactivate the alert. 2.
Installing and Configuring the Director 2/64 Delete Alerts Use the following steps to delete existing threshold alerts. 1. At the Hardware View page, choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays. 2. Choose the alert that you want to delete by selecting the alert information in the table and click Delete. A message displays asking you to confirm the deletion. 3. Click Yes. The alert is removed from the dialog box.
Installing and Configuring the Director 2/64 5. Click OK. Verify that the intended users received the Call-Home and e-mail notifications. Back Up HAFM Configuration Data It is important to back up the HAFM configuration data. This data is used to restore the HAFM server operating environment in case of hard drive failure. Refer to the HP StorageWorks HAFM server installation guide for instructions on backing up the HAFM configuration data.
Installing and Configuring the Director 2/64 Enable Embedded Web Server Use the following steps to enable EWS: 1. At the Hardware View page, choose Configure > Enable Web Server. Choosing Enable Web Server automatically places a check mark in the check box. 2. Choose Enable Web Server again to remove the check mark and disable the EWS interface. When disabled, remote users cannot access the interface. For complete procedures on using EWS, refer to the HP StorageWorks Embedded Web Server User Guide.
Installing and Configuring the Director 2/64 . 1 2 Director 2/64 Fibre Channel cables 3 Workstation Figure 54: Connect the Fibre Channel cables 2. Connect device cables to ports and route the cables through the cable management assembly at the bottom front of the director. Start with the center UPM cards (cards 7 and 8) adjacent to the CTP2 cards and work outward. In addition, start with the bottom port of each UPM card and work upward. 3.
Installing and Configuring the Director 2/64 Use these steps to fabric-attach the director and create an ISL: 1. Verify that the director is defined via HAFM. See “Enabling HAFM to Manage the Director” on page 80. 2. Verify that the preferred domain ID for the director is unique and does not conflict with the ID of another director or switch participating in the fabric. To change the domain ID, see “Configure Fabric Parameters” on page 93. 3.
Installing and Configuring the Director 2/64 Figure 55: Port Properties dialog box Using HAFM from a Remote Location Use this section to install the HAFM client on a remote workstation. Remote Workstation Minimum Requirements The following minimum requirements must be met in order to install HAFM on a remote workstation: Note: In order for HAFM to function properly, compatible versions must be installed on both the client and server machines.
Installing and Configuring the Director 2/64 — Sun Microsystems® UltraPARC-II processor with a 300 MHz or greater clock speed, using the SunOS Version 5.5.1 or higher operating system, or Solaris Version 2.5.1 or higher operating system. — IBM PowerPC® microprocessor with a 233 MHz or greater clock speed, or POWER3 microprocessor with a 333 MHz or greater clock speed, using the AIX Version 4.3.3 or higher operating system. ■ At least 15 MB available on the internal hard drive. ■ 32 MB or greater RAM.
Installing and Configuring the Director 2/64 Figure 56: HAFM remote client install 5. To install the HAFM remote client application, scroll down to the information that pertains to your platform and follow the instructions provided. 6. After you have downloaded the installer executable, the InstallAnywhere Wizard displays. Follow the instructions provided to continue the installation. Launch HAFM from the Remote Client Use these steps to launch HAFM from a remote client: 1.
Manage Firmware Versions 3 3 The Director 2/64 internal operating code is downloaded from the HAFM server and stored on a CTP2 card. Up to eight versions can be stored on the HAFM server hard drive and made available for download to a director.
Manage Firmware Versions Determine a Director Firmware Version Use these steps to determine the Director 2/64 firmware version: 1. At the HAFM server, open the HAFM application. The Products View page displays. 2. Double-click the icon representing the director to be inspected for firmware version. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 57.
Manage Firmware Versions Add a Firmware Version The firmware version shipped with the director is provided on the Director 2/64 documentation CD. Subsequent firmware versions to upgrade the director are provided to customers through the Hewlett-Packard website. Note: When adding a firmware version, follow procedural information in the release notes that accompany the firmware version. This information supplements information provided in this general procedure.
Manage Firmware Versions 4. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 57. 5. Click New. The New Firmware Version dialog box displays, as shown in Figure 58. Figure 58: New Firmware Version dialog box 6. Choose the desired firmware version file (downloaded in step 1) from the HAFM server backup drive, CD-ROM drive, or hard drive. Verify that the correct directory path and filename display in the File name field and click Save.
Manage Firmware Versions 10. To send the firmware version to a director, see “Download a Firmware Version to a Director” on page 123. Modify a Firmware Version Description Use these steps to modify the description of a director firmware version in the library stored on the HAFM server hard drive: 1. At the HAFM server, open the HAFM application. The Products View page displays. 2. Double-click the icon representing the director for which the firmware version description will be modified.
Manage Firmware Versions Delete a Firmware Version Use these steps to delete a firmware version from the library stored on the HAFM server hard drive: 1. At the HAFM server, open the HAFM application. The Products View page displays. 2. Double-click the icon representing the director from which the firmware version will be deleted. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 57. 4.
Manage Firmware Versions Download a Firmware Version to a Director This procedure downloads a selected firmware version from the HAFM server library to a director managed by the open instance of the Product Manager application. The procedure applies to a director with two (redundant) CTP2 cards. The process occurs concurrently without taking the director offline or disrupting operation. The new firmware version takes effect when control is passed from the active to the backup CTP2 card.
Manage Firmware Versions c. Choose Maintenance > Backup & Restore Configuration. The Backup and Restore Configuration dialog box displays, as shown in Figure 61. Figure 61: Backup and Restore Configuration dialog box d. Click Backup. When the backup process finishes, the Backup Complete dialog box displays. e. Click OK to close the dialog box and return to the Hardware View page. 5. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 57. 6.
Manage Firmware Versions to show percent completion of the download. The bar progresses to 50% when the last file is transmitted to the first CTP2 card. The bar remains at the 50% point until the director performs an Initial Program Load (IPL) (indicated by an “IPLing” message).
Manage Firmware Versions Back Up the Director’s Configuration Use these steps to back up the configuration file to the HAFM server: 1. At the HAFM server, open the HAFM application. The Products View displays. 2. Double-click the icon representing the director for which the configuration file will be backed up. The Hardware View page for the selected director displays. 3. Choose Maintenance > Backup & Restore Configuration. The Backup and Restore Configuration dialog box displays, as shown in Figure 61. 4.
Regulatory Compliance Notices A A This appendix covers the following topics: ■ Regulatory Compliance ID Numbers, page 128 ■ Federal Communications Commission Notice, page 129 ■ IEC EMC Statement (Worldwide), page 131 ■ Spécification ATI Classe A (France), page 131 ■ Canadian Notice (Avis Canadien), page 131 ■ European Union Notice, page 132 ■ Japanese Notice, page 132 ■ Harmonics Conformance (Japan), page 133 ■ German Noise Declaration, page 133 ■ Laser Safety, page 134 ■ Declaration
Regulatory Compliance Notices Regulatory Compliance ID Numbers For the purpose of regulatory compliance certifications and identification, your HP StorageWorks Director 2/64 is assigned a Hewlett-Packard Regulatory Model Number. The Hewlett-Packard Regulatory Model Number for this product is: RSVLB-0211 The HP StorageWorks Director 2/64 Regulatory Model Number can be found on the product label, along with the required approval markings and information.
Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ■ Reorient or relocate the receiving antenna. ■ Increase the separation between the equipment and receiver. ■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Regulatory Compliance Notices IEC EMC Statement (Worldwide) This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Regulatory Compliance Notices European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Regulatory Compliance Notices Harmonics Conformance (Japan) German Noise Declaration Schalldruckpegel Lp = 68.
Regulatory Compliance Notices Laser Safety WARNING: To reduce the risk of exposure to hazardous radiation: • • • Do not try to open the laser device enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only Hewlett-Packard authorized service technicians to repair the laser device.
Regulatory Compliance Notices Declaration of Conformity The Declaration of Conformity is shown below: Director 2/64 Installation Guide 135
Regulatory Compliance Notices 136 Director 2/64 Installation Guide
Technical Specifications B B This appendix contains the following information: ■ Physical Dimensions, page 138 ■ Environmental Specifications, page 138 ■ Power Requirements, page 139 ■ Operating Tolerances, page 139 ■ Laser Information, page 140 Director 2/64 Installation Guide 137
Technical Specifications Physical Dimensions Table 6 lists Director 2/64 dimensions. Table 6: Dimensions Dimension Size Height 39.7 cm (15.7 in) Width 44.5 cm (17.5 in) Depth 54.6 cm (21.5 in) Weight 52.3 kg (115 lb) Shipping Weight 76.4 kg (168 lb) Environmental Specifications Table 7 lists environmental ranges for shipping, storing, and operating the HP StorageWorks Director 2/64. Table 7: Environmental Specifications Specification 138 Shipping Storage Operating Weight 76.
Technical Specifications Power Requirements Table 8 lists Director 2/64 power requirements. Table 8: Power Requirements Specification Value Input voltage 100 to 120 or 200 to 240 VAC Input frequency 50/60 Hz Operating Tolerances Table 9 lists heating and cooling specifications, shock and vibration tolerances, acoustical noise, and inclination.
Technical Specifications Laser Information Three configurations of cards with fixed optics will be provided for each of the connector types: four extended long-wave ports, four long-wave ports, and four short-wave ports. Table 10 lists the 2 Gb laser specifications.
Electrostatic Discharge C C This appendix contains the following information: ■ Precautions Against Electrostatic Discharge, page 142 ■ Grounding Methods, page 142 Director 2/64 Installation Guide 141
Electrostatic Discharge Precautions Against Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
index 9000 series rack installation 50 A AIX operating system 115 alerts, introduction 22 allen wrench, caution 34 asynchronous RS-232 null modem cable 35 audience 12 authorized reseller, HP 17 C cable management assembly 29 cables, FCC compliance statement 130 call-home feature introduction 23 Canadian Notice (Avis Canadien) 131 carton contents 45, 47 CE marking 132 CFR, laser compliance 29 changing the director’s IP address 73 class 1 laser transceivers 29 clock speed, processor 114 Code of Federal Reg
Index configure feature key procedure 110 configure switch parameters 89, 90 director e_d_tov 26 fibre channel addresses 91 firmware 119 general description 20 installation tools required 49 management, overview 21 NV-RAM 89, 93 r_a_tov 26 rerouting delay 92 tools supplied 34 director 2/64 hardware components 27 installing 49 optional kits 37 director 2/64 firmware library dialog box 118 director 2/64 shipping carton items 46 director firmware adding version 119 deleting a version 122 downloading 123 versi
Index protective plug 35 Fibre Alliance MIB 23 fibre channel addresses 91 Fibre Channel ports connecting cables 111 FICON port addresses, configuring 99 FICON devices, communication 88 FICON management server 89, 110 FICON management style FICON management server 89 firmware deleting version 122 determining version 118 modifying description 121 release notes 119 firmware library 118 frames routing of 92 front bezel 28 FRUs, CTP2 card 28 G g_ports 30 UPM card 29 getting help 17 grounding methods 142 H HA
Index ISL, g_port 30 items director 2/64 shipping carton 46 L laser devices 134 information 135 laser transceivers 29 LEDs CTP2 cards 28 front bezel 28 power supplies 29 SBAR assembly 33 UPM card 30 lift device 49 Linux operating system, version 114 logic card, torque tool, caution 34 logs, introduction 22 long-wave laser transceivers 31 loopback plug multi-mode 34 single-mode 34 M MAC address 73 maintenance port 23, 33, 34 management server FICON 110 open systems 110 management style FICON 89 open syste
Index P PDU 56, 67 port addresses, FICON, configuring 99 port loopback diagnostic tests, fiber optic loopback plug 34 POST 71 power module assembly 33 power supplies 29 power supply requirements 139 power switch 33, 34 POWER3 microprocessor 115 power-on self test 71 PowerPC microprocessor 115 precautions against electrostatic discharge 142 preferred domain ID 91 multi-switch fabric 90 principal switch, determining 95 ProComm Plus 36 product manager SNMP agent 21 protective plug 35 R r_a_tov 94 greater tha
Index technical specifications, power requirements 139 technical support, HP 17 telnet, enabling 111 text symbols 13 tips for installing 49 tools supplied by service personnel 36 supplied with director 34 tools required to install a director 49 torque tool 34 caution 34 trap messages maximum recipients 23 U UltraSPARC-II processor 115 UNIX workstation, specifications 114 UPM cards 29 V versions AIX operating system 115 Director 2/64 firmware 21 FC fabric element MIB 23 firmware deleting 122 determining 1
