Installation Guide hp StorageWorks Director 2/64 Product Version: FW v06.xx/HAFM SW v08.02.00 Fourth Edition (July 2004) Part Number: AA–RSNGD–TE/958–000289–002 This guide provides procedures for setting up, configuring, and managing the HP StorageWorks Director 2/64.
© Copyright 2001–2004 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents Contents About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Intended audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Related documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents SBAR Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Module Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools Supplied with the Director . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents HAFM Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Element ManagerEnabling HAFM to Manage the Director . . . . . . . . . . . . . . . . . . . . . . 78 Verify Communication Between the Director and HAFM Appliance. . . . . . . . . . . . . . . 79 Set Director Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Set Date and Time Manually . . . . . . . . . . . . .
Contents Activating or Deactivating Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deleting Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Backing Up HAFM Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Open Systems Management Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring FICON Management Server . . . . . . . . . . . . .
Contents Japanese Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Harmonics Conformance (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . German Noise Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 8 Installing a Tinnerman nut on the rack-front rail in U1 . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Inserting the rail tray in the rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Preparing the front rack columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 57 58 59 60 61 62 63 64 65 66 67 New Threshold Alerts dialog box—summary screen . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Threshold Alerts dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the Fibre Channel cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Properties dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 10 Director 2/64 Installation Guide
About this Guide About this Guide This guide provides information on installing, configuring, managing, and verifying operation of the HP StorageWorks Director 2/64. The Director switch About this Guide connects storage devices, hosts, and servers in a SAN. The director is easily managed and configured to optimize the performance of your SAN.
About this Guide Overview This section covers the following topics: ■ Intended audience ■ Related documentation Intended audience This guide is part of a documentation set that supports the Director. It is intended for use by trained service and installation representatives experienced with the SAN technology and Fibre Channel technology.
About this Guide Conventions Conventions consist of the following: ■ Document conventions ■ Text symbols ■ Equipment symbols Document conventions This document follows the conventions in Table 1.
About this Guide Tip: Text in a tip provides additional help to readers by providing nonessential or optional techniques, procedures, or shortcuts. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Equipment symbols The following equipment symbols may be found on hardware for which this guide pertains.
About this Guide Power supplies or systems marked with these symbols indicate the presence of multiple sources of power. WARNING: To reduce the risk of personal injury from electrical shock, remove all power cords to completely disconnect power from the power supplies and systems. Any product or assembly marked with these symbols indicates that the component exceeds the recommended weight for one individual to handle safely.
About this Guide Getting help If you still have a question after reading this guide, contact an HP authorized service provider or access our web site: http://www.hp.com. HP technical support Telephone numbers for worldwide technical support are listed on the following HP web site: http://www.hp.com/support/. From this web site, select the country of origin. Note: For continuous quality improvement, calls may be recorded or monitored.
Overview 1 This chapter contains the following HP StorageWorks Director 2/64 information: ■ Director Description, page 18 ■ Features, page 18 ■ Hardware Components, page 24 ■ Tools and Test Equipment, page 31 ■ Optional Kits, page 34 Director 2/64 Installation Guide 17
Overview Director Description The director is a second-generation, 64-port product that provides dynamic switched connections between Fibre Channel servers and devices in a SAN environment. Directors are managed and controlled through an High Availability Fabric Manager (HAFM) appliance with HAFM and Director 2/64 Element Manager installed. The HAFM appliance is a 1U rack-mount appliance that provides a central point of control for up to 48 directors and/or edge switches.
Overview Director Management The director is managed and controlled through: ■ The HAFM application. This graphical user interface (GUI) resides on the HAFM appliance and provides a single point of management for all directors, and a launching point for the Director 2/64 Element Manager. ■ Simple network management protocol (SNMP).
Overview ■ A customer-supplied PC platform with a network connection to the EWS interface installed on the director. ■ A customer-supplied server platform communicating with the switch through a LAN or corporate intranet. The HAFM applications are ordered and installed on the server by the customer.
Overview ■ A modular design that enables quick removal and replacement of FRUs without tools or equipment. ■ Concurrent port maintenance—UPM cards are added or replaced and fiber-optic cables are attached to ports without interrupting other ports or director operation. ■ Beaconing to assist service personnel in locating a specific port, FRU, or director in a multi-switch environment. When port beaconing is enabled, the amber LED associated with the port flashes.
Overview Zoning The director supports a name server zoning feature that partitions attached devices into restricted-access groups called zones. Devices in the same zone can recognize and communicate with each other through switched port-to-port connections. Devices in separate zones cannot communicate with each other. Zoning is configured by authorizing or restricting access to name server information associated with device N_Ports that attach to director fabric ports (F_Ports).
Overview ■ Domain ID assignment—Each director in a fabric is identified by a unique domain ID that ranges from 1 through 31. A domain ID of 0 is invalid. If two operational fabrics join, they determine if any domain ID conflicts exist between the fabrics. If one or more conflicts exist, the E_Ports that form the interswitch link (ISL) segment to prevent the fabrics from joining.
Overview — Build fabric protocol error—A protocol error is detected during the process of forming the fabric. — No principal switch—No director in the fabric is capable of becoming the principal switch. — No response from attached switch—After a fabric is created, each director in the fabric periodically verifies operation of all attached switches and directors. An ISL segments if a switch or director does not respond to a verification request.
Overview 1 2 3 Power and system error LEDs UPM cards Power supplies 1. 4 5 6 Cable management assembly1 Front bezel CTP2 cards Provided in rack-mount kits HP 9000, HP 10000, and HP 11000 Series only. Figure 1: Director components—front CTP2 Card The Director 2/64 ships with two Control Processor (CTP2) cards. The active CTP2 card initializes and configures the director after power on, and contains the microprocessor and associated logic that coordinate director operation.
Overview Each CTP2 card provides System Services Processor (SSP) and Embedded Port (EP) subsystems. The SSP subsystem runs director applications, communicates with director ports, and controls the RS-232 maintenance port and 10/100 Mbps ethernet port. The EP subsystem provides Class F processing, and manages frame transmission to and from the Serial Crossbar Assembly (SBAR).
Overview The power supplies are input rated at 85 to 264 VAC. The faceplate of each power supply provides the following status LEDs: ■ A green PWR OK LED turns ON if the power supply is operational and receiving AC power. ■ An amber FAULT LED turns ON if the power supply fails. ■ An amber TEMP LED turns ON if the power supply shuts down due to an over temperature condition. ■ An amber I LIM LED turns ON if the power supply is overloaded and operating at the current limit (15.6 A).
Overview UPM 1 2 1 2 3 3 Card LED Port LEDs Port Connectors (G_Ports) SHR-2 Figure 2: UPM card LEDs and connectors Single-mode or multi-mode fiber-optic cables attach to UPM cards through small form factor pluggable (SFP) optic transceivers. The fiber-optic transceivers provide duplex connectors, and can be detached from UPM cards (through a 10-pin interface) for easy replacement.
Overview Extended reach long-wave Laser—Long-wave laser transceivers that provide connections for transferring data over extended long distances (up to 35 kilometers) through 9-µm single-mode fiber. ■ Rear View Figure 3 shows the components accessible from the rear of the Director2/64.
Overview SBAR Assembly The director ships with two SBAR assemblies. The active SBAR is responsible for Fibre Channel frame transmission from any director port to any other director port. Connections are established without software intervention. The assembly accepts a connection request from a port, determines if a connection can be established, and establishes the connection if the destination port is available. The assembly also stores busy, source connection, and error status for each director port.
Overview Tools and Test Equipment This section describes tools and test equipment that may be required to test, service, and verify operation of the director and attached HAFM appliance. These tools are either supplied with the director or must be supplied by service personnel. Tools Supplied with the Director The following tools are supplied with the director. Use of the tools may be required to perform test, installation, service, or verification tasks.
Overview ■ Loopback plug—An SFP multi-mode (shortwave laser) or single-mode (longwave laser) loopback plug, as shown in Figure 5, is required to perform port loopback diagnostic tests. One loopback plug is shipped with the director, depending on the type of port transceivers installed. Both plugs are shipped if shortwave laser and longwave laser transceivers are installed.
Overview Figure 7: Null modem cable Tools Supplied by Service Personnel The following tools are expected to be supplied by service personnel performing director installation or maintenance actions. Use of the tools may be required to perform one or more test, service, or verification tasks. ■ Scissors or pocket knife—A sharp cutting edge (scissors or knife blade) may be required to cut the protective strapping when unpacking replacement FRUs.
Overview ■ Fiber-optic cleaning kit—The kit contains tools and instructions to clean fiber-optic cable, connectors, loopback plugs, and protective plugs. Optional Kits Contact your Hewlett-Packard authorized service provider to purchase the following optional Director kits. See Table 2 for descriptions of Director 2/64 optional kits. Table 2: Director Optional Kits Supporting Kit 34 Description HP Full Volatility License. Part Number: A7498A Provides a license to use Full Volatility feature.
Installing and Configuring the Director 2 This chapter describes tasks to install, configure, and verify operation of the Director.
Installing and Configuring the Director Installation Options The director is installed in one of two configurations. The options are: 36 ■ Table or desk top—One or more directors and an optional HAFM appliance are delivered and installed at the customer facility on a desk or table top. Ethernet cabling distance and local area network (LAN) addressing issues must be considered.
Installing and Configuring the Director Review Installation Requirements The director is delivered stand-alone and ready to be mounted in an HP 9000, HP 10000, HP 11000, HP system/e, or industry-standard 19-in rack. Ethernet cabling, distance, and LAN addressing issues must be considered. Review the following checklist before installing the switch: ■ Prepare a site plan. Consult the HP StorageWorks SAN High Availability Planning Guide.
Installing and Configuring the Director Items Required for Installation Locate the following items before beginning the installation procedure: ■ Lift device (recommended). ■ Director 2/64. ■ An HP 9000, HP 10000, HP 11000, HP system/e, or industry-standard 19-in rack, or any rack with the following specifications: — A minimum depth of 24.5 in. — 19 in wide. — A minimum opening size of 10U available (9U for the director and 1U for the rail tray kit).
Installing and Configuring the Director Note: The HAFM appliance may be used for the maintenance terminal function. The HyperTerminal application is included with the Windows 2000 operating system provided with the HAFM appliance. Select an Operating Location Install the director in a secure or limited-access area to ensure that cable connections are not compromised. Also, make sure to install the director in an area with the necessary ventilation and power requirements.
Installing and Configuring the Director Unpack and Inspect the Director Unpack and inspect the director as follows: 1. Inspect the shipping container for damage caused during transit. 2. Unpack the shipping cartons. WARNING: The Director weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. 3.
Installing and Configuring the Director s.
Installing and Configuring the Director Table 3: Shipping Carton Contents for a Director 2/64 (Continued) Number Item 3 Two Power Distribution Unit (PDU) power cords 4 Two standard AC power cords 5 Four multi-mode, short-wave loopback plugs 6 One torque driver with integrated 5/32” bit 7 One 10-foot null modem cable 8 HP StorageWorks Director 1 2 3 4 Figure 9: Carton contents for an HP 9000, HP 10000, and HP 11000 Series Rack Table 4: Shipping Carton Contents for an HP 9000, HP 10000, and
Installing and Configuring the Director Table 4: Shipping Carton Contents for an HP 9000, HP 10000, and HP 11000 Series Rack (Continued) Number 3 Item Pouch containing HP 9000, HP 10000, and HP 11000 Series rack-mounting hardware: ■ ■ ■ ■ ■ ■ ■ ■ 4 Director 2/64 Installation Guide Eight 10-32 x 0.375 in Phillips panhead screws—Installs two shelf brackets to rails Six 10-32 x 0.375 in Phillips panhead screws—Installs two front mounting brackets to rails Four 10-32 X 0.
Installing and Configuring the Director 1 2 3 5 4 Figure 10: Carton contents for a HP system/e or industry-standard 19-in rack installation 44 Director 2/64 Installation Guide
Installing and Configuring the Director Table 5: Parts for Installing in an HP System/e and Industry-Standard 19-inch Rack Label Item 1 HP StorageWorks Director (part number: A6534-62001) 4 Rail Tray Kit (part number: A6534-60016): One rail tray ■ Two mounting brackets ■ Two M3 Tinnerman nuts ■ Four Torx T25 16 mm M5 SEM screws ■ 2, 3, 5 Mounting hardware: ■ ■ ■ ■ ■ ■ ■ ■ Director 2/64 Installation Guide Rack-mount brackets (part number: A6534-60014) containing: Two front mounting brackets (5) Two
Installing and Configuring the Director Install the Director in a Rack The following sections provide instructions for installing the Director in either the HP 9000, HP 10000, and HP 11000 Series Rack or in the HP system/e and industry-standard 19-in racks.
Installing and Configuring the Director WARNING: The Director weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. Two people will need to work together to transfer the director to the lift. Make sure the wheels of the lift cannot roll as you transfer the director to the lift. Move the director slowly and carefully onto the lift to prevent back and hand injury. Dropping the director could injure personnel or damage the equipment.
Installing and Configuring the Director 2. Locate the small, round marker hole on the rails that coincides with the location selected in step 1. Each marker hole delineates the beginning of one rail unit, or U. 3. Locate the square opening in the rail that corresponds with the appropriate marker hole, as shown in Figure 11. 4. Position the higher, shelf bracket threaded hole in this square opening, as shown in Figure 11. 5. Orient the shelf bracket in the rails. 6.
Installing and Configuring the Director 1 2 3 4 SHR-2265B 1 2 Marker hole Square opening in rail 3 4 Screws with captive lock and flat washers Square alignment washers Figure 11: Securing shelf brackets Secure the Mounting Hardware Use these steps to secure the mounting hardware to the switch. 1. Locate the two front mounting brackets in the shipping carton. 2. Secure the front mounting brackets on either side of the switch, as shown in Figure 12.
Installing and Configuring the Director Figure 12: Securing the two mounting brackets 3. Using a torque driver, torque the screws to 22 in/lb. 4. Locate the two (2) rear mounting plates in the shipping carton. 5. Secure the two (2) rear mounting plates to each side of the switch, as shown in Figure 12. For each plate, use the two (2) flathead countersunk Phillips screws (10-32 x 0.25 in) provided. 6. Using a torque driver, torque the screws to 22 in/lb.
Installing and Configuring the Director 3. Count up five (5) square openings from the cage nut you just installed, and insert the next cage nut. 4. Count up four (4) square openings and install the third cage nut. 5. Repeat this procedure to install cage nuts in the corresponding front rail. Insert the Rear Cage Nuts in the Rack Use these steps to insert the four (4) supplied cage nuts in the rack’s rear rails: 1. Select one of the rear rails. 2.
Installing and Configuring the Director Figure 13: Aligning the switch in the rack 3. Loosely attach the rear angle bracket to the rack rail with the two panhead Phillips screws provided, as shown in Figure 14. 4. Repeat step 2 and step 3 for the corresponding rear angle bracket, as shown in Figure 14. 5. The two rear angle brackets now touch the outside surfaces of the rear mounting plates. Slide the switch all the way into the rack to where the front mounting bracket meets the rack rails. 6.
Installing and Configuring the Director Figure 14: Securing the rear angle brackets 7. Using a torque driver, torque the screws to 22 in/lb. 8. Connect the remaining ends of the PDU power cords to separate PDUs (if installed), as shown in Figure 15; otherwise, connect the two standard AC power cords. Note: Hewlett-Packard recommends installing an optional PDU in the rack. Hewlett-Packard ships two PDU power cords with the Director.
Installing and Configuring the Director Figure 15: AC power connections HP System/e and Industry-Standard 19-inch Rack Installation To install the director in a HP system/e or industry-standard 19-in rack, complete the procedures in the following sections: ■ Install the Anti-tip Feet on an HP System/e Rack, page 54 ■ Install Mounting Bracket Hardware in the Rack, page 55 ■ Prepare the Front and Rear Rack Columns, page 59 ■ Prepare the Switch for Installation, page 60 ■ Finalize the Rack-Mounting
Installing and Configuring the Director Figure 16: Mounting anti-tip feet for a HP system/e rack Install Mounting Bracket Hardware in the Rack Use these steps to install the mounting hardware in a rack. Note: The 9Us used to mount the switch are called U1 through U9; U1 is the lowest of the 9Us. Note also that 1U below the switch is required for the rail tray for a total of 10U to mount the switch. 1. Determine the appropriate placement for the switch inside the rack.
Installing and Configuring the Director Figure 17: Rail tray mounting location requirement 4. Position and attach both rear brackets, as shown in Figure 18: a. Locate the lowest U of the 9Us chosen for mounting the switch (the lowest being U1). b. Attach each rear rail tray bracket to the rear rack uprights at U1 (one on the left and one on the right. c. Secure each rail tray bracket using one M5 Torx screw.
Installing and Configuring the Director 3 1 2 3 Rear tray bracket M5 screw with attached lock washer HP rack 1 2 Figure 18: Attaching a rear rail tray bracket 5. Install a Tinnerman nut in the top holes of U1 for both the left and right rack-front uprights, as shown in Figure 19.
Installing and Configuring the Director 6. Position the rail tray, as shown in Figure 20 and insert the tray into the rack from the front. Note: Make sure the slots in the sides of the rail tray slide over the posts on the rear rail tray brackets, and the posts on the rail tray’s front mounting flanges are inserted into the center holes of U1. Figure 20: Inserting the rail tray in the rack 7. Secure the rail tray: a. Insert an M5 Torx screw through the top holes in both of the rail tray mounting flanges.
Installing and Configuring the Director Prepare the Front and Rear Rack Columns Use the following procedure to prepare the rack for installing a switch: 1. Prepare the front rack columns, as shown in Figure 21: a. Standing at the front of the rack, count up from the top of the rail tray (1) to the 13th, 19th, and 23rd holes on the rack's front face. b. Slide a sheet metal nut (2) on each of the located holes. Note: Three sheet metal nuts should be on each front column face (3).
Installing and Configuring the Director Note: Two sheet metal nuts should be on each back column face (3). Figure 22: Preparing the rear rack columns Prepare the Switch for Installation The following section describes how to install the mounting hardware that attaches the switch to the rails.
Installing and Configuring the Director 3. Attach the bracket with 10-32, flat-head Phillips screws (4) using the two center threaded holes on the front side of the switch. 4. Repeat step 2 and step 3 for the second front mounting bracket. Figure 23: Installing the rack-mounting brackets on the switch 5. Locate the two rear mounting brackets in the shipping carton. 6.
Installing and Configuring the Director WARNING: The Director weighs approximately 115 pounds. Use proper handling and lifting equipment to reduce the possibility of injury or product damage. 1. Carefully position the switch in the front of the rack and onto the rail tray, and slide the switch back on the rails until the front mounting brackets are against the front rack columns. Figure 24 illustrates using a lifting jack to position the switch. Figure 24: Positioning the switch in the rack 2.
Installing and Configuring the Director d. Repeat step a through step c for the other side at the back of the switch. e. At the front of the rack, insert the screws through the front mounting brackets into the sheet metal nuts installed in the rail columns in step 1 of “Prepare the Front and Rear Rack Columns” on page 59. f. Tighten all screws. Figure 25: Securing the switch to the rack 3.
Installing and Configuring the Director WARNING: Hewlett-Packard power cords are provided for each director power supply. To prevent personal injury by electric shock, use only the supplied power cords. Also, verify that the facility power receptacle is the correct type, supplies the required voltage, and is properly grounded. 4. Connect the equipment rack power cords to separate (for redundancy) facility power sources, providing single-phase, 120 to 240 VAC current.
Installing and Configuring the Director Figure 27: Installing the sliding shelf brackets 6. Insert the shelf into the rack so that both rail rear slots (1) slide over the loose screws (2) on the inside face of each bracket, as shown in Figure 28.
Installing and Configuring the Director Figure 28: Positioning the sliding shelf bracket on a rail rear slot 7. Make sure that the sliding shelf and rails are horizontal, as shown in Figure 29 at the rack front. 8. Push each of the rail front tabs (1) into the corresponding holes on the rack columns (2). 9. At the back of the rack, tighten the screws that attach the sliding shelf rails to the mounting brackets, as shown in Figure 28 (2).
Installing and Configuring the Director Figure 29: Positioning the sliding shelf bracket at the rack front Recommended Cable Management Perform the following procedure after installing a switch, as shown in Figure 30: 1. Install two cable restraints (1) on each side of the rack in positions that will hold the Fibre Channel cables away from the power supply. 2. Form loose bundles of the installed Fibre Channel cables (2) on each side of the rack. 3.
Installing and Configuring the Director Figure 30: Recommended cable management Power-On Self Test Use the following steps to run a Power-On Self Test (POST): 1. Power on the PDUs (if used). 2. At the bottom rear of the director, set the power switch (circuit breaker) to the Up position. The director powers on. The following occurs during POST: 68 ■ Amber LEDs on both CTP2 cards and all universal port module (UPM) cards illuminate momentarily.
Installing and Configuring the Director 3. After successful POST completion, the green power LED on the front bezel, green LED on the active CTP2 card, and green PWR OK LEDs on both power supplies remain ON. 4. If a POST error or other malfunction occurs, refer to the HP StorageWorks Director 2/64 Service Manual.
Installing and Configuring the Director Configure Director Network Information Use the following sections to configure the director’s network addressing scheme. Default Settings The director is delivered with the following default network addresses: ■ MAC address—The Media Access Control (MAC) address is programmed into FLASH memory on the CTP2 card at the time of manufacture. The address is in xx.xx.xx.xx.xx.xx format, where xx is a hexadecimal pair.
Installing and Configuring the Director Changing the Director’s IP Address If multiple directors are installed, or a public LAN segment is used, network addresses must be changed to conform to the customer’s LAN addressing scheme. The following items are required to perform this task: ■ A local workstation (desktop or notebook computer) with: — Microsoft Windows 98, Windows 2000, Windows 2003, Windows XP, Windows Millennium Edition, or Windows NT 4.
Installing and Configuring the Director 1 2 Maintenance port RS-232 port 3 Null Modem cable Figure 31: Connecting the null modem cable between the director and a workstation 2. Connect the 9-pin end of the RS-232 modem cable to the maintenance port. 3. Connect the other cable end to a 9-pin communication port (COM1 or COM2) at the rear of the local workstation.
Installing and Configuring the Director 4. Choose Start > Programs > Accessories > Communications > HyperTerminal. The Connection Description dialog box displays, as shown in Figure 32. Figure 32: Connection Description dialog box 5. Enter 264 in the Name field and click OK. The Connect To dialog box displays, as shown in Figure 33. Figure 33: Connect To dialog box 6.
Installing and Configuring the Director Figure 34: COMn Properties dialog box 7. Configure the Port Settings parameters as follows: ■ Bits per second: 115200 ■ Data bits: 8 ■ Parity: None ■ Stop bits: 1 ■ Flow control: Hardware 8. Click OK. The HyperTerminal window displays. 9. At the > prompt, enter the user-level password (the default is password) and press the Enter key. The password is case-sensitive. The HyperTerminal window displays with a C> prompt at the top of the window. 10.
Installing and Configuring the Director Only the IP Address, Subnet Mask, and Gateway Address fields are configurable. Figure 35: HyperTerminal window 11. To change director network addresses, enter the following at the C> prompt and press Enter. ipconfig xxx.xxx.xxx.xxx.yyy.yyy.yyy.yyy.zzz.zzz.zzz.zzz The IP address format is xxx.xxx.xxx.xxx. The subnet mask format is yyy.yyy.yyy.yyy. The gateway address format is zzz.zzz.zzz.zzz. The octets xxx, yyy, and zzz are decimals from 0 through 255.
Installing and Configuring the Director Figure 37: HyperTerminal dialog box (2) 14. Click No to exit and close the HyperTerminal application. 15. Power off the maintenance terminal: a. Choose Start > Shut Down. The Shut Down Windows dialog box displays. b. Choose Shut down and click Ok to power off the PC. 16. Disconnect the RS-232 null modem cable from the director and the maintenance terminal. Replace the protective cap over the maintenance port.
Installing and Configuring the Director LAN-Connect the Director Use these steps to connect the rack-mounted director to the Ethernet LAN segment. 1. Connect one end of an Ethernet cable to the RJ-45 connector on each CTP2 card, as shown in Figure 38. 1 2 Remote workstation Ethernet hub or switch (customer supplied) 3 4 HAFM appliance (laptop or rack-mount) Director 2/64 Figure 38: LAN-connect the director 2.
Installing and Configuring the Director HAFM Appliance To run HAFM software, you must set up and configure the HAFM appliance.
Installing and Configuring the Director Figure 40: Domain Information dialog box (IP Address page) 3. Enter a director description in the Description field. 4. Enter the IP address you configured earlier. See “Configure Director Network Information” on page 70 for more information. 5. Enter the director subnet mask (determined by the customer network administrator) in the Subnet Mask field. 6.
Installing and Configuring the Director Table 6: Director Operational States and Symbols Operational State Symbol Operational—Director-to-server communication has been established, the director is operational, and no failures are indicated. No Status Symbol Degraded—Director-to-server communication has been established, but the director is operating in degraded mode and requires service. This condition is typical if a port or redundant FRU fails. Go to step 2.
Installing and Configuring the Director Figure 41: Hardware View page (with FRU failures) Set Director Date and Time The Director Element Manager log entries are stamped with the date and time received from the director. Use these steps to set the effective date and time for the director: Note: The director and HAFM synchronize at least once daily. 1. At the Hardware View, choose Configure > Date/Time. The Configure Date and Time dialog box displays, as shown in Figure 42. 2.
Installing and Configuring the Director Figure 42: Configure Date and Time dialog box Set Date and Time Manually Use these steps to set the director date and time manually: 1. At the Configure Date and Time dialog box, click the Periodic Date/Time Synchronization check box to deselect the option (no check mark in the box). The grayed-out Date and Time fields activate. 2.
Installing and Configuring the Director 3. Click Sync Now to synchronize the director and HAFM immediately. The Date and Time Synced dialog box displays. Figure 43: Date and Time Synced dialog box 4. Click OK. 5. Click Activate to enable synchronization.
Installing and Configuring the Director Frequently Used HAFM Settings This section summarizes the most common HAFM tasks including: Note: For a complete reference on HAFM functionality, refer to the HP StorageWorks HA-Fabric Manager User Guide.
Installing and Configuring the Director Setting the Director Online When the director is set online, an attached device can log into the director if the port is not blocked. Attached devices can communicate with each other if they are configured in the same zone. Use these steps to set the director online: 1. Open HAFM. The View All - HAFM 8 page displays. 2. Double-click the appropriate director icon. The Hardware View page for the selected director displays. 3. Choose Maintenance > Set Online State.
Installing and Configuring the Director Follow these steps to configure the director identification: 1. At the Hardware View page, choose Configure > Identification. The Configure Identification dialog box displays, as shown in Figure 44. Figure 44: Configure Identification dialog box 2. Enter a director name of 24 or fewer alphanumeric characters in the Name field. Each director should be configured with a unique name. 3.
Installing and Configuring the Director the director is set to FICON management style, and FICON devices can communicate with each other if the director is set to open systems management style. Note: If the FICON management server feature is enabled, the default management style is FICON. Open systems management style cannot be enabled. To configure the director management style: 1. Ensure the director is set offline. For instructions, see “Setting the Director Offline” on page 85. 2.
Installing and Configuring the Director 2. Choose Configure > Operating Parameters > Switch Parameters. The Configure Switch Parameters dialog box displays, as shown in Figure 45. Figure 45: Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID. Change this value if the director will participate in a multi-switch fabric. 3.
Installing and Configuring the Director Use this field to set a unique domain ID for the director. The default value is 1. Set a value between 1 and 31. When a director comes online with a preferred ID, it requests an ID from the fabric’s principal director (indicating its preferred value as part of the request). If the requested domain ID is not allocated to the fabric, the domain ID is assigned to the requesting director. If the requested domain ID is already allocated, an unused domain ID is assigned.
Installing and Configuring the Director routed over this new path if its hop count is less than a previous path with a minimum hop count. This may result in frames being delivered to a destination out of order since frames sent over the new, shorter path may arrive ahead of older frames still in route over the older path. If rerouting delay is enabled, traffic ceases in the fabric for the time specified in the E_D_TOV field of the Configure Fabric Parameters dialog box.
Installing and Configuring the Director Director Speed At the Director Speed field, choose 1 Gb/sec or 2 Gb/sec to select the speed of Fibre Channel operation. Note: Changing the switch speed to 2 Gb/s with any 1 Gb/s FPM cards installed will cause the following warning/confirmation message to display: “All FPM ports will be held inactive while the switch is configured to 2 Gb/sec speed.
Installing and Configuring the Director 5. Back up the configuration data when you are finished configuring the switch. 6. Set the director online. For instructions, see “Setting the Director Online” on page 85. Fabric Parameters Configure the following parameters as required by your fabric. BB_Credit Configure the director to support buffer-to-buffer credit (BB_Credit) from 1 through 60. This is the value used for all ports, except those configured for extended distance buffering (10-100 km).
Installing and Configuring the Director Switch Priority Setting this value determines the principal director for the multi-switch fabric. Choose Principal (highest priority), Default, or Never Principal (lowest priority) from the Switch Priority drop-down list. Setting these priority values determines the principal director selected for the multi-switch fabric.
Installing and Configuring the Director ■ Homogeneous Fabric—Choose this mode if the fabric contains only HP directors and edge switches that are operating in Homogeneous Fabric mode. ■ Open Fabric 1.0—Default. Choose this mode if the fabric contains HP directors and edge switches, as well as other open-fabric compliant switches. Choose this mode for managing heterogeneous fabrics.
Installing and Configuring the Director Figure 47: Configure Ports check boxes c. Click the 10-100 km check box to enable extended distance buffering for a port. A check mark in the box indicates the extended distance operation up to 100 kilometers (through repeaters) is enabled. d. Click the LIN Alerts check box to enable or disable LIN alerts for a port. A check mark in the box indicates alerts are enabled.
Installing and Configuring the Director g. Click the Port Binding check box to enable WWN binding for the port, which allows only a specific device to attach to the port. This device is specified by the WWN or nickname entered into the Bound WWN column. With the check box cleared, any device can attach to the port even if a WWN or nickname is specified in the Bound WWN column. h. In the Bound WWN field, enter a world wide name (WWN) in the correct format (xx.xx.xx.xx.xx.xx.xx.
Installing and Configuring the Director Figure 48: Configure SNMP dialog box a. For each trap recipient to be configured, enter a community name of 32 or fewer alphanumeric characters in the associated Community Name field. The community name is incorporated in SNMP trap messages to ensure against unauthorized viewing or use. b. Click the check box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled).
Installing and Configuring the Director Use these steps to configure and enable e-mail and SMTP server addresses: 1. At the HAFM main page, choose Monitor > Event Notification > E-Mail. The E-Mail Event Notification Setup dialog box displays, as shown in Figure 49. Figure 49: E-Mail Event Notification Setup dialog box 2. To enable e-mail transmission of configured addresses, click Enable E-Mail Event Notification. A check mark displays in the box when transmission is enabled.
Installing and Configuring the Director Figure 50: HAFM 8 Server Users dialog box 7. To enable e-mail notification for a user, choose the check box in the Email column. An unchecked box indicates e-mail notification is not enabled. 8. To configure event types for which e-mail notification is sent, choose the Filter link adjacent to the check box. The Define Filter dialog box displays. Figure 51: Define Filter dialog box 9. Choose the filters that you want for this user. 10.
Installing and Configuring the Director 12. Click Test Email. A test message is sent to configured e-mail recipients. 13. Click OK to save the information and close the Email Event Notification Setup dialog box. 14. Maximize the Hardware View (Element Manager). 15. At the Hardware View, choose Maintenance > Enable E-Mail Notification. A check mark displays in the check box to indicate e-mail notification for the director is enabled, and the menu closes.
Installing and Configuring the Director Configuring Threshold Alerts A threshold alert notifies users when the transmit (Tx) or receive (Rx) throughput reaches specified values for specific director ports or port types, (E_Ports or F_Ports). You are notified of a threshold alert by: ■ A yellow triangle that displays on the port in the Port Card View. ■ A yellow triangle that displays on the port in the Hardware View. ■ A yellow triangle that displays in the Alert column of the Port List View.
Installing and Configuring the Director Note: If alerts are configured, they will display in table format showing the name of the alert, type of alert (Rx, Tx, or Rx or Tx), and alert state (inactive or active). Figure 53: Configure Threshold Alerts dialog box 2. Click New. The New Threshold Alert dialog box displays, as shown in Figure 54. Figure 54: New Threshold Alerts dialog box—first screen 3. Enter a name from one to 64 characters in length.
Installing and Configuring the Director 4. Choose one of the following from the drop-down list under the Name field: ■ Rx Throughput—An alert will occur if the threshold set for receive throughput is reached. ■ Tx Throughput—An alert will occur if the threshold set for transmit throughput is reached. ■ Rx or Tx Throughput—An alert will occur if the threshold set for either receive or transmit throughput is reached. 5. Click Next.
Installing and Configuring the Director 8. Enter the interval in minutes in which throughput is measured and threshold notifications can occur. The valid range is 5 minutes to 70,560 minutes. 9. Click Next. A new screen displays for selecting ports for the alerts, as shown in Figure 56. Figure 56: New Threshold Alerts dialog box—third screen 10. Choose either Port Type or Port List.
Installing and Configuring the Director Figure 57: New Threshold Alerts dialog box—summary screen 12. Click Finish. The Configure Threshold Alerts dialog box displays, as shown in Figure 58. Figure 58: Configure Threshold Alerts dialog box 13. At this point, the alert is not active. To activate the alert, choose the alert information that displays in the Configure Threshold Alerts table and click Activate. The alert is activated.
Installing and Configuring the Director Modifying Alerts Use the following steps to modify an existing threshold alert configuration. 1. At the Hardware View page, choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays. Choose the alert that you want to modify by clicking the alert information in the table. If the alert is active, an error message displays prompting you to deactivate the alert. 2.
Installing and Configuring the Director Deleting Alerts Use the following steps to delete existing threshold alerts. 1. At the Hardware View page, choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays. 2. Choose the alert that you want to delete by selecting the alert information in the table and click Delete. A message displays asking you to confirm the deletion. 3. Click Yes. The alert is removed from the dialog box.
Installing and Configuring the Director Configuring Open Trunking This option is only available if the optional Open Trunking feature is installed. Choosing this option opens the Configure Open Trunking dialog box. For details on enabling Open Trunking and configuring such parameters as congestion thresholds for ports, event notification options, and low BB credit threshold, refer to the HP StorageWorks Director Element Manager User Guide.
Installing and Configuring the Director Connecting Cables to the Fibre Channel Ports Use these steps to connect Fibre Channel port cables: 1. Route the fiber-optic cables from customer-specified devices to ports at the front of the director, as shown in Figure 59. . 1 2 Director 2/64 Fibre Channel cables 3 Workstation Figure 59: Connect the Fibre Channel cables 2. Connect device cables to ports and route the cables through the cable management assembly at the bottom front of the director.
Installing and Configuring the Director Connecting the Director to a Fabric To attach the director to a multi-switch fabric, connect the director to an E_Port of another director or switch. The E_Port to E_Port connection is referred to as an ISL. Use these steps to fabric-attach the director and create an ISL: 1. Verify that the director is defined via HAFM. See “Element ManagerEnabling HAFM to Manage the Director” on page 78. 2.
Installing and Configuring the Director 8. Verify that the Link Incident field displays None. If an ISL segmentation or other problem is indicated, consult the HP StorageWorks Director 2/64 Service Manual to isolate the problem. If no problems are indicated, installation is complete. Unpacking, Inspecting, and Installing the Ethernet Hub (Optional) The HAFM appliance and one or more directors connect through an Ethernet hub installed on a 10/100 Mbps LAN segment.
Installing and Configuring the Director Using HAFM from a Remote Location Using a standard Web browser, the client HAFM and Director Element Manager can be downloaded and installed on PCs or workstations that are LAN-attached to the HAFM appliance. Operators at these platforms can manage and monitor directors or switches controlled by the appliance. A maximum of 25 concurrent users can log in to the HAFM appliance. Each client must have access to the LAN segment on which the HAFM appliance is installed.
Installing and Configuring the Director ■ 512 MB or greater RAM. ■ Video card supporting 256 colors at 800 x 600 pixel resolution. ■ Ethernet network adapter. ■ Java-enabled Internet browser, such as Microsoft Internet Explorer (Version 4.0 or later) or Netscape Navigator (Version 4.6 or later). Installing HAFM Client on a Remote Workstation Use these steps to install HAFM on a remote client: 1.
Installing and Configuring the Director 5. To install the HAFM remote client application, scroll down to the information that pertains to your platform and follow the instructions provided. 6. After you have downloaded the installer executable, the InstallAnywhere Wizard displays. Follow the instructions provided to continue the installation. Launching HAFM from the Remote Client Use these steps to launch HAFM from a remote client: 1. Double-click the HAFM icon to launch HAFM.
Installing and Configuring the Director 4. If you want your computer to save the login information, choose the Save Password option. 5. Click Login. The View All - HAFM 8 window displays, as shown in Figure 63. Figure 63: View All - HAFM 8 window 6.
Installing and Configuring the Director 116 Director 2/64 Installation Guide
Managing Firmware Versions 3 The Director 2/64 internal operating code is downloaded from the HAFM appliance and stored on a CTP2 card. Up to eight (8) versions can be stored on the HAFM appliance hard drive and made available for download to a director.
Managing Firmware Versions Determining a Director Firmware Version Use these steps to determine the Director firmware version: 1. Open the HAFM application. The View All - HAFM 8 main window displays. 2. Double-click the icon representing the director to be inspected for firmware version. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 64.
Managing Firmware Versions Adding a Firmware Version The firmware version shipped with the director is provided on the Director documentation CD. Subsequent firmware versions to upgrade the director are provided to customers through the Hewlett-Packard website. Note: When adding a firmware version, follow procedural information in the release notes that accompany the firmware version. This information supplements information provided in this general procedure.
Managing Firmware Versions 4. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 64. 5. Click New. The New Firmware Version dialog box displays, as shown in Figure 65. Figure 65: New Firmware Version dialog box 6. Select the desired firmware version file (downloaded in step 1) from the HAFM appliance backup drive, CD-ROM drive, or hard drive. Verify that the correct directory path and filename display in the File name field and click Save.
Managing Firmware Versions Modifying a Firmware Version Description Use these steps to modify the description of a director firmware version in the library stored on the HAFM appliance hard drive: 1. Open the HAFM application. The View All - HAFM 8 main window displays. 2. Double-click the icon representing the director for which the firmware version description will be modified. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library.
Managing Firmware Versions Deleting a Firmware Version Use these steps to delete a firmware version from the library stored on the HAFM appliance hard drive: 1. Open the HAFM application. The View All - HAFM 8 main window displays. 2. Double-click the icon representing the director from which the firmware version will be deleted. The Hardware View page for the selected director displays. 3. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 64. 4.
Managing Firmware Versions Downloading a Firmware Version to a Director This procedure downloads a selected firmware version from the HAFM appliance library to a director managed by the open instance of the Element Manager. The procedure applies to a director with two (redundant) CTP2 cards. The process occurs concurrently without taking the director offline or disrupting operation. The new firmware version takes effect when control is passed from the active to the backup CTP2 card.
Managing Firmware Versions c. Choose Maintenance > Backup & Restore Configuration. The Backup and Restore Configuration dialog box displays, as shown in Figure 67. Figure 67: Backup and Restore Configuration dialog box d. Click Backup. When the backup process finishes, the Backup Complete dialog box displays. e. Click OK to close the dialog box and return to the Hardware View page. 5. Choose Maintenance > Firmware Library. The Director Firmware Library dialog box displays, as shown in Figure 64. 6.
Managing Firmware Versions ■ As the network connection drops, the director Status table turns yellow, the Status field displays No Link, and the State field displays a reason message. ■ The alert panel at the bottom of the navigation control panel displays a gray square, indicating director status is unknown. ■ Illustrated FRUs in the Hardware View page are removed, and then displayed again as the connection is re-established. After the IPL, a “Synchronizing CTP2s” message displays.
Managing Firmware Versions Backing Up the Director’s Configuration Use these steps to back up the configuration file to the HAFM appliance: 1. Open the HAFM application. The View All - HAFM 8 main window displays. 2. Double-click the icon representing the director for which the configuration file will be backed up. The Hardware View page for the selected director displays. 3. Choose Maintenance > Backup & Restore Configuration.
Regulatory Compliance Notices A This appendix covers the following topics: ■ Regulatory Compliance ID Numbers, page 128 ■ Federal Communications Commission Notice, page 128 ■ IEC EMC Statement (Worldwide), page 130 ■ Spécification ATI Classe A (France), page 130 ■ Canadian Notice (Avis Canadien), page 131 ■ European Union Notice, page 131 ■ Japanese Notice, page 132 ■ Harmonics Conformance (Japan), page 132 ■ German Noise Declaration, page 132 ■ Laser Safety, page 133 ■ Declaration of
Regulatory Compliance Notices Regulatory Compliance ID Numbers For the purpose of regulatory compliance certifications and identification, your HP StorageWorks Director is assigned a Hewlett-Packard Regulatory Model Number. The Hewlett-Packard Regulatory Model Number for this product is: RSVLB-0211 The HP StorageWorks Director Regulatory Model Number can be found on the product label, along with the required approval markings and information.
Regulatory Compliance Notices Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Regulatory Compliance Notices Hewlett-Packard Company Product Regulations Manager 3000 Hanover St. Palo Alto, CA 94304 Or call 1-650-857-1501 To identify this product, refer to the part, Regulatory Model Number, or product number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Regulatory Compliance Notices Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Regulatory Compliance Notices Japanese Notice Harmonics Conformance (Japan) German Noise Declaration Schalldruckpegel Lp = 68.
Regulatory Compliance Notices Laser Safety WARNING: To reduce the risk of exposure to hazardous radiation: • • • Do not try to open the laser device enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only Hewlett-Packard authorized service technicians to repair the laser device.
Regulatory Compliance Notices Declaration of Conformity The Declaration of Conformity is shown below: 134 Director 2/64 Installation Guide
Technical Specifications B This appendix contains the following information: ■ Physical Dimensions, page 136 ■ Environmental Specifications, page 136 ■ Power Requirements, page 137 ■ Operating Tolerances, page 137 ■ Laser Information, page 137 Director 2/64 Installation Guide 135
Technical Specifications Physical Dimensions Table 7 lists Director 2/64 dimensions. Table 7: Dimensions Dimension Size Height 39.7 cm (15.7 in) Width 44.5 cm (17.5 in) Depth 54.6 cm (21.5 in) Weight 52.3 kg (115 lb) Shipping Weight 76.4 kg (168 lb) Environmental Specifications Table 8 lists environmental ranges for shipping, storing, and operating the HP StorageWorks Director 2/64. Table 8: Environmental Specifications Specification 136 Shipping Storage Operating Weight 76.
Technical Specifications Power Requirements Table 9 lists Director 2/64 power requirements. Table 9: Power Requirements Specification Value Input voltage 100 to 120 or 200 to 240 VAC Input frequency 50/60 Hz Operating Tolerances Table 10 lists heating and cooling specifications, shock and vibration tolerances, acoustical noise, and inclination.
Technical Specifications Table 11: Laser specs - 2 Gb Part Number Transceivers on UPM Card Wave Length Media/Distance Standard 300836-B21 Long wave 35 Km 4 Extended Long wave 1310 nm 9/125 µm Single-mode: 1 m–35 Km 100-SM-LL-L 300835-B21 Long wave 10 Km 4 Long wave 1310 nm 9/125 µm Single-mode: 1 m–10 Km 100-SM-LL-L 300834-B21 Short wave 4 Short wave 850 nm 50/125 µm Multi-mode: 2 m–500 m 100-M5-SN-I 62.
Electrostatic Discharge C This appendix contains the following information: ■ Precautions Against Electrostatic Discharge, page 140 ■ Grounding Methods, page 140 Director 2/64 Installation Guide 139
Electrostatic Discharge Precautions Against Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
index A AIX operating system 112 alerts, introduction 20 allen wrench, caution 31 asynchronous RS-232 null modem cable 32 audience 12 authorized reseller, HP 16 B cable management assembly 26 cables, FCC compliance statement 130 call-home feature introduction 20 Canadian Notice (Avis Canadien) 131 carton contents 44 CE marking 131 CFR, laser compliance 27 changing the director’s IP address 71 class 1 laser transceivers 27 clock speed, processor 112 Code of Federal Regulations 27 COMn properties dialog bo
Index configure fabric parameters 91 configure feature key procedure 107 configure switch parameters 87, 88 director e_d_tov 23 fibre channel addresses 88 firmware 119 general description 18 hardware components 24 installation tools required 46 management, overview 19 NV-RAM 87, 91 r_a_tov 23 rerouting delay 89 tools supplied 31 director 2/64 installing 46 director 2/64 shipping carton items 41 director firmware adding version 119 deleting a version 122 downloading 123 version 118 director firmware library
Index Federal Communications Commission (FCC) notice 128 fiber optic cleaning kit 34 protective plug 32 Fibre Alliance MIB 21 fibre channel addresses 88 Fibre Channel ports connecting cables 109 FICON port addresses, configuring 96 FICON devices, communication 86 FICON management server 87, 107 FICON management style FICON management server 87 firmware deleting version 122 determining version 118 modifying description 121 release notes 119 firmware library 118 frames routing of 89 front bezel 26 FRUs, CTP
Index mounting hardware 49, 60 positioning the director in the rack 51, 61 shelf brackets 47, 55 tips 46 installing rear angle brackets 52 Intel Pentium processor 112 Internet Explorer 113 interop mode 93 homogeneous fabric 94 open fabric 1.
Index interop mode 94 open systems management server 107 open systems management style 87 optional kits combination long-wave/short-wave port module kit 34 short-wave port module kits 34 OSI devices, communication 86 P password default Windows 2000 114 PDU 53, 63 port addresses, FICON, configuring 96 port loopback diagnostic tests, fiber optic loopback plug 32 POST 68 power module assembly 30 power supplies 26 power supply requirements 137 power switch 30, 31 POWER3 microprocessor 112 power-on self test 6
Index switch priority 93 related number codes 93 switch priority setting 93 switches, principal, determining 93 symbols in text 13 symbols on equipment 14 synchronize date and time 82 T TCP/IP MIB-II definition 21 technical specifications, power requirements 137 technical support, HP 16 telnet, enabling 108 text symbols 13 tips for installing 46 tools supplied by service personnel 33 supplied with director 31 tools required to install a director 46 torque tool 31 caution 31 trap messages maximum recipient
