addendum hp StorageWorks SAN switch universal rack mount kit installation Product Version: V3.0.x/V4.0.x This addendum only applies to the following documents: HP StorageWorks SAN Switch 2/32 Installation Guide, Version 4.0.x AA–RTQVB–TE (February 2003) HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x AA–RR84B–TE (February 2003) HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x AA–RSB6B–TE (February 2003) © 2003 Hewlett-Packard Company AV–RU6YA–TE Printed in the U.S.A.
Pen-and-ink Changes This addendum consists two parts: ■ Pen-and-ink Changes—provides instructions for locating specific text and either deleting text, replacing text with new text, or adding new text at a specific location. ■ Page Additions—identifies where to add a page at a specific place in the document and recommends how to attach the replacement pages.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit This section provides instructions for installing the SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series or comparable EIA rack using the SAN Switch Universal Rack Mount Kit, part number 331148-B21.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit A right inner rail and a right outer rail A left inner rail and a left outer rail (14) #8-32 x 3/16-inch Phillips pan-head screw with captive star lock washer (10) #10-32 x 1/2-inch Phillips pan-head screw with captive star lock washer (8) #10 alignment washer (8) #10 adapter washer (2) 1/4-20 hex nut with captive star lock washer (2) 1/4-inch flat washer 2 Addendum Pg HP StorageWorks SAN Switch 2/8|16|32 Installation Gu
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Caution: For proper airflow, the SFP media side of the SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This mounting allows air to enter from the front of the rack and to exhaust at the rear of the rack, similar to other rack-mounted equipment. This prevents switch overheating, which may cause it to fail. To install the switch in a rack: 1.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit — For an HP System/e rack, install each of the two rear mounting brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10 alignment washers as shown in Figure 3.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Note: This kit contains both left rails and right rails. The rails are marked with Right and Left to distinguish the rails from each other. 4. Assemble the outer rails by completing the following steps: a. Attach the left outer rail and the right outer rails to the rear mounting brackets using (2) 1/4-20 hex nuts with captive star lock washers attached loosely as shown in Figure 4. Don’t tighten them.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit b. Depending on the rack you are using, complete one of the following tasks: — For an HP 9000 Series or comparable EIA rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 adapter washers in the upper and lower hole locations of the right rail.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit — For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 alignment washers in the upper and lower hole locations of the right rail. Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and two #10 alignment washers in the upper and lower hole locations of the left rail. See Figure 6.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit 6. For the SAN Switch 2/32 and SAN Switch 2/16, perform step a. For the SAN Switch 2/8, perform step b. Caution: Do not use any other screws other than the fourteen that are provided. Use of any longer lengths can cause damage to internal components Note: The inner rails work for all three SAN switches—SAN Switch 2/32, SAN Switch 2/16, and SAN Switch 2/8. The mounting holes in the inner rails are marked with 32, 16, and 8.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit a. Assemble the two inner rails (one on each side) to the switch using the appropriate number (from step 5) of #8-32 x 3/16-inch Phillips pan-head screws as shown in Figure 7. Note: The rail kit provides fourteen #8-32 x 3/16-inch screws for assembling the inner rails. Each switch requires a different number of these screws. For example, Figure 7 shows the an inner rail being attached to the SAN Switch 2/16 with five screws.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit b. For the SAN Switch 2/8, assemble the two inner rails (one on each side) to the switch and plenum using the appropriate number (from step 5) of #8-32 x 3/16-inch Phillips pan-head screws as shown in Figure 8. Note: The plenum is only a required part of this installation when the SAN Switch 2/8 is installed in the HP System/e rack. The plenum is not needed if the switch is installed in an HP 9000 Series or comparable EIA rack.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit 7. Insert the switch with the attached inner rails into the outer rails. Note: This step applies to both the HP System/e rack and the HP 9000 Series or comparable EIA rack. Figure 9: Installing the switch into a rack (HP 9000 Series or comparable EIA rack) Insert the switch into the rack and install (2) #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers with one on each side. See Figure 9 and Figure 10.
Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit Figure 10: Installing the switch into a rack (HP System/e rack) 8. Tighten the nuts installed in step a of step 4 on page 5. See Figure 4. Note: To uninstall a switch, remove the middle #10-32 x 1/2-inch Phillips pan head screw with captive star lock washer from either side of the rack uprights. 9. Continue the installation by returning to one of the following guides as appropriate. a.