HP StorageWorks 1510i Modular Smart Array installation and user guide active/active firmware v2.
Legal and notice information © Copyright 2005, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . Intended audience . . . . . . . Prerequisites . . . . . . . . . Related documentation . . . . . Document conventions and symbols Rack stability . . . . . . . . . HP technical support . . . . . . Customer self repair . . . . . . Product warranties . . . . . . . Subscription service . . . . . . HP websites . . . . . . . . . . Documentation feedback . . . . 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key websites . . . . . . . . . . . . . . . . . . . . . Key MSA1510i installation best practices . . . . . . . . . Preparing the site . . . . . . . . . . . . . . . . . . . . . Providing structural support for the floor . . . . . . . . . . Providing clearance space and ventilation . . . . . . . . . Providing power sources . . . . . . . . . . . . . . . . Chassis specifications . . . . . . . . . . . . . . . . . Preparing the network . . . . . . . . . . . . . . . . . . . Preparing the servers . . . . . . . . . .
Updating MSA firmware . . . . . . . . . . . . . . . . . . . . . . . . . About MSA controller firmware . . . . . . . . . . . . . . . . . . . . Determining which components to update . . . . . . . . . . . . . . . . Updating MSA controller firmware . . . . . . . . . . . . . . . . . . . Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . Updating MSA firmware using the SMU . . . . . . . . . . . . . . . Updating MSA firmware using the MSA-CLI . . . . . . . . . . . . . Cloning controller firmware .
Japanese power cord notice . . . . . . . . Electrostatic discharge . . . . . . . . . . Preventing electrostatic discharge . . . . Grounding methods . . . . . . . . . Waste Electrical and Electronic Equipment directive Czechoslovakian notice . . . . . . . . . . Danish notice . . . . . . . . . . . . . . Dutch notice . . . . . . . . . . . . . . English notice . . . . . . . . . . . . . . Estonian notice . . . . . . . . . . . . . Finnish notice . . . . . . . . . . . . . . French notice . . . . . . . . . . . . .
Tables 1 Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2 Helpful websites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 3 Levels of protection against power failure . . . . . . . . . . . . . . . . . . . . . . 53 4 MSA1510i normal status lights . . . . . . . . . . . . . . . . . . . . . . . . . . 55 5 MSA1510i controller LCD startup messages . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about installing, configuring, and using the MSA1510i. Intended audience This guide is intended for network administrators and storage managers with moderate or advanced knowledge of IP and storage networks. Prerequisites The following are prerequisites for installing or using this product: • Determine who will install and configure your system.
http://www.ietf.org/internet-drafts/draft-ietf-ips-iscsi-slp-09.txt • Zeroconf: http://ietf.org/internet-drafts/draft-ietf-zeroconf-ipv4-linklocal-10.txt • 802.1q for Virtual LANs: http://www.ieee802.org/1/pages/802.1Q.html Operating system specific information can be found on the following websites: • Microsoft Windows: http://www.microsoft.com • Novell Linux: http://www.novell.com • HP-UX: http://www.hp.com • VMware: http://www.vmware.
TIP: Provides helpful hints and shortcuts. Rack stability Rack stability protects personnel and equipment. WARNING! To • • • • • reduce the risk of personal injury or damage to equipment: Extend leveling jacks to the floor. Ensure that the full weight of the rack rests on the leveling jacks. Install stabilizing feet on the rack. In multiple-rack installations, fasten racks together securely. Extend only one rack component at a time. Racks can become unstable if more than one component is extended.
Subscription service HP recommends that you register your product at the Subscriber’s Choice for Business website: http://www.hp.com/go/e-updates After registering, you will receive e-mail notification of product enhancements, new driver versions, firmware updates, and other product resources. HP websites For additional information, see the following HP websites: • • • • • http://www.hp.com http://www.hp.com/go/storage http://www.hp.com/service_locator http://www.hp.com/support/manuals http://www.hp.
1 Overview This chapter provides a brief overview of the MSA1510i. • Product overview • iSCSI overview Product overview • • • • MSA1510i product features MSA1510i front features MSA1510i rear features Shipping contents MSA1510i product features The MSA1510i is a flexible, scalable iSCSI IP SAN solution. • Employs iSCSI technology, using TCP for moving data between application end points, and leverages Ethernet IP infrastructure, familiar to most users worldwide.
• SCSI and SATA hard drive firmware flashing is supported directly from the SMU using HP Firmware Maintenance CD 7.90 and later. For more information, see the SMU user guide. Front features 1. Blank for an additional controller (controller slot 2) 2. Serial port for a CLI connection 3. MSA1510i controller (controller slot 1) 4. Controller status lights 5. Controller LCD message display panel 6. Controller LCD panel push buttons 7. Chassis Power On/Standby button 8.
Rear features 1. 2–Port Ethernet iSCSI module (for the controller in slot 1) 2. Chassis slot diagram 3. Fan modules 4. SCSI I/O module (bus 0) 5. Power supply modules 6. Blank for additional 2-Port Ethernet iSCSI module (for the controller in slot 2) 7.
Shipping contents 1. 1510i Modular Smart Array (MSA1510i) 2. 2U universal rack mounting kit 3. Printed documents, 2U rack mounting template, and documentation CD 4. Custom CLI configuration cable 5.
iSCSI overview • • • • Targets Initiators Switches Key iSCSI best practices IMPORTANT: The following overview is very brief. For additional detail, see the MSA1510i iSCSI concepts and deployment guide, provided on the MSA1510i Support CD v2.0 and MSA1510i support page: http://www.hp.com/support. Targets A target is a grouping of one or more MSA Logical Units (LUNs). The target is the unit presented to the network, with the initiator granted access to the target (and its assigned LUNs.
• Disable unused or insecure services (such as telnet). • Change the logon username and password of the Storage Management Utility.
2 System components and LEDs This chapter includes figures and tables that identify system components and describe chassis and module LEDs patterns. • Front view • Rear view • Chassis and component LEDs Front view 1. Chassis LEDs 2. Chassis Power On/Standby button 3. Blank for an additional controller (controller slot 2) 4. MSA1510i controller (controller slot 1) 5. Controller LCD message display panel 6.
Rear view 1. 2–Port Ethernet iSCSI module (for the controller in slot 1) 2. Chassis slot diagram 3. Blank for additional 2-Port Ethernet iSCSI module (for the controller in slot 2) 4. Power supply module 2 5. Power supply module 1 6. SCSI I/O module (bus 0) 7. Blank for additional SCSI I/O module (bus 1) 8. Fan module 2 9. Fan module 1 10. Blank for additional SCSI I/O module (bus 2) 11. Blank for additional SCSI I/O module (bus 3) 12. Unused slot NOTE: Each MSA SCSI I/O module has two ports.
Chassis and component LEDs The MSA chassis and its modular components are equipped with LEDs. When the fault LED on any MSA component is amber, promptly determine the reason for the alert by examining the component, the messages displayed on the MSA controller LCD panel, and system event logs (such as those provided by HP Systems Insight Manager). The following sections define the LEDs.
NOTE: System power does not shut off completely with the power button. Standby removes power from most of the electronics and the hard drives, but portions of the power supply and some internal circuitry remain active. To remove the power completely, disconnect all power cords from the device. For instructions, see “Powering off the MSA1510i” on page 77. Controller LEDs During normal runtime, the array controller has 18 LEDs that indicate controller activity or malfunction.
Item Name Condition Color Meaning 1 SCSI bus 3 activity On Green There is activity on this SCSI bus. 2 SCSI bus 2 activity On Green There is activity on this SCSI bus. 3 SCSI bus 1 activity On Green There is activity on this SCSI bus. 4 SCSI bus 0 activity On Green There is activity on this SCSI bus. 5 Logical I/O activity On Green Requests from the host are being processed. 6 Direct Memory Access activity On Green Direct Memory Access transfers are active.
Item 1 Activity LED nl On Item 2 Online LED nl Off Blinking Off Blinking Off Item 3 Fault LED Meaning Off The hard drive is being accessed in one of the following ways: • The hard drive is not configured as part of an array. • The hard drive is a replacement and rebuild has not yet started. • The hard drive is spinning up during POST. Do not remove the hard drive. Removing a hard drive at this time could terminate the current operation and cause data loss.
SATA hard drive LEDs Each SATA hard drive has two LEDs. The following figure and table describe their locations and meanings. Item 1 Online/ Activity LED (green) Item 2 Fault/UID LED (amber/blue) Meaning On, off, or blinking Alternating amber and blue The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application.
Slot diagram LEDs Located on the rear of the MSA, the slot diagram provides information about MSA modules. 1. 2–Port Ethernet iSCSI module (for the controller in slot 2) 2. SCSI I/O module (bus 3) 3. SCSI I/O module (bus 2) 4. Fan module 1 5. Fan module 2 6. 2–Port Ethernet iSCSI module (for the controller in slot 2) 7. SCSI I/O module (bus 1) 8. SCSI I/O module (bus 0) 9. Power supply 1 10.
2-Port Ethernet iSCSI module LEDs The 2-Port Ethernet iSCSI module has one LED to show the status of the module, and each port has two LEDs to show status and activity information for the specific port. Item 1 2 3 Name Module status Port status Port activity Color Meaning Solid Green Power is on, the module is operational, and communication between the module and the controller is established. Blinking Amber Power is on, but there is no communication to the controller.
Fan module LEDs Each fan module has one bi-color LED. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Fault Condition Color Meaning Solid Green The power is on. Off — The power is off. Blinking Amber A fault was detected in this module. Fan modules cool the chassis by circulating air through the enclosure. The rate at which air moves (the airflow) determines the amount of cooling.
SCSI I/O module LEDs The SCSI I/O module has two LEDs. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Condition Color Description Solid Green The power is on. Off — The power is off. Blinking Green There is activity on this SCSI module. Off — There is no activity on this SCSI module.
Power supply module LEDs The power supply uses a single bi-color LED to indicate status. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Fault 30 Condition Color Description Solid Green The power is on. Off — The power is off. Blinking Amber A fault was detected on this module.
3 Installation Installing the MSA1510i includes: • Planning and getting started tasks • Preparing the site • Preparing the network • Installing MSA hardware options • Racking the MSA and the storage enclosures • Installing hard drives in the enclosures • Connecting cables • Powering on the MSA • Verifying the operating status of the devices Planning and getting started tasks • • • • • • • • • Reading the MSA1510i iSCSI concepts and deployment guide Adding the MSA1510i website as a favorite in your browser
Adding the MSA1510i website as a favorite in your browser This site (http://www.hp.com/go/msa1510i) includes the latest information about the MSA1510i, including product specifications, compatibility information, software and firmware downloads, user documents, and support advisories and notifications. Confirming that your network devices and tools are supported Specific versions of hardware, firmware, software, drivers, and multipathing components are designed to work together.
Reviewing all old advisories and notices To help you better plan for and successfully install your MSA1510i, read all of the outstanding customer advisories before installing the MSA1510i. Advisories are available on the MSA1510i support page: http://www.hp.com/support. On this page, click See support and troubleshooting information. Also look for Troubleshoot a problem.
Table 2 Helpful websites MSA1510i: http://www.hp.com/go/msa1510i • Latest controller firmware and approved driver versions • Compatibility guide (supported component and version information) • Quickspecs (technical information) • Release notes and system documentation MSA products: http://www.hp.com/go/msa Storage products: http://www.hp.com/storage Servers: http://www.hp.com/go/servers Clustering: http://h18000.www1.hp.com/solutions/enterprise/highavailability/index.
• • • • • • • • • • • • • • • MSA1510i redundant controller and redundant Ethernet iSCSI I/O module (optional—for multipath configurations) • Hard drive storage enclosures (MSA20 SATA, MSA30 SCSI, or other supported models) • Hard drives Confirm that the hardware and software components you plan to use are supported for use with the MSA1510i. Before initially installing your MSA and before making any configuration changes, check the MSA1510i Compatibility guide, available on the MSA1510i website.
• Depending on the number of physical hard drives included in a storage unit, the Storage Management Utility may suggest RAID 6 (ADG) as the default RAID level, which offers a high level of fault tolerance and usable disk capacity, but at a significant cost to I/O performance. For comparable fault tolerance but higher performance, consider using RAID 1+0 when fault tolerance is desired and performance is more important than usable capacity.
Providing clearance space and ventilation Provide adequate clearance around the front and back of the racks. Provide at least 25 inches (63.5 cm) in the front of the rack to allow the doors to open fully and provide at least 30 inches (76.2 cm) in the rear of the rack to allow for servicing and airflow. If there are unused spaces in your rack, attach blanking panels across those empty spaces to force the airflow through the components instead of through the open spaces.
Chassis specifications Parameter Value Height 8.78 cm (3.46 in.) Width 48.41 cm (19.06 in.) Depth 61.77 cm (24.32 in.) Weight 24.95 kg (55 lb) Input voltage requirements Rated input voltage 100 to 240 VAC Rated input frequency 47 Hz to 63 Hz Rated input current 6.
Preparing the servers When preparing servers for the MSA1510i, be sure to do the following tasks. For detailed installation and configuration information, see the documentation provided with the server or software tools. Be sure to record information about the servers that will connect to the MSA1510i. (“Server information” on page 146) • Verify that the servers, Ethernet NICs, Ethernet switches, operating system version, and service packs are supported for use with the MSA1510i.
Be sure to record information about the switches that will connect to the MSA1510i. (“Basic MSA1510i information” on page 142) For installation instructions, see the document shipped with each kit. CAUTION: Remove blanking panels only for the options being installed. For proper airflow and cooling, a blanking panel or component must be installed in the MSA chassis.
CAUTION: Install hard drives in the enclosures only after mounting the enclosures in the rack. • An enclosure populated with hard drives is to too heavy to lift safely. • Movement of an enclosure during installation might damage the internal storage media of installed hard drives.
1. If desired, use the instructions on the provided rack template to mark the holes on the front and rear rack uprights that will be used by the rails. 2. If the holes in the rack uprights are round instead of square, remove the standard pins from the rails and replace them with the provided smaller round-hole pins. CAUTION: Pins in the rails are load-bearing. Do not remove the standard pins except to replace them with the smaller pins for round-hole racks. 3.
4. From the front of the rack, align the front end of the rail with the marked holes on the rack. Disengage the scissor-pin locking latch by pulling the bottom of the latch towards the front of the rack and, at the same time, insert the end of the rail into the inside-front of the rack, making sure that the scissor-pin clicks into place. Release the locking latch and verify that it engages the scissor-pin. 5.
6. If necessary, loosen the locking nut on the device retaining bracket and slide the bracket to the farthest position near the rear of the rack. 7. Repeat through to install the other rail. 8. Remove the bezel from the front of the MSA1510i by grasping the bezel by its left and right outside edges, and then, with even pressure, pulling toward you until the retaining clips disengage. 9. From the front of the rack, place the MSA1510i on the rails and slide it into the rack.
10. Slide the MSA1510i into the rack until the front edge is flush with the front of the rack. Then, secure the MSA1510i to the front of the rack by tightening the thumbscrews on the front of the MSA1510i. 11. From the rear of the rack, secure the rear of the MSA by sliding the retaining bracket toward the MSA1510i, until the tab engages the slot in the MSA chassis. Then, tighten the thumbscrew on the bracket. 12.
Installing hard drives in the enclosures After the storage enclosures are secured in the rack, install hard drives into the drive bays. For installation instructions, see the documents shipped with the hard drive or enclosure.
Connecting cables Connecting cables includes: • • • • Cabling best practices Connecting SCSI cables Connecting Ethernet cables Connecting power cords Cabling best practices • Use the shortest possible cable between devices. Shorter cables are easier to manage and route along the back of the rack. In addition, shorter cables reduce the possibility of signal degradation that can occur over longer distances.
Item Bus 1 0 2 1 3 2 4 3 newpage pi 48 Installation Port Assigned box number—SATA Assigned box number—SCSI A 1 1 B 5 not used A 2 2 B 6 not used A 3 3 B 7 not used A 4 4 B 8 not used
Supported and unsupported SCSI connections Each SCSI I/O module has two ports. Depending on the type of storage enclosure you plan to connect, one or both of the ports might be supported.
Connecting SATA storage enclosures In the following illustration, two MSA20 SATA storage enclosures are connected to the MSA1510i using the pre-installed MSA SCSI I/O module. 1 MSA1510i controller shelf 2 MSA20 SATA storage enclosure (SCSI bus 0, Box 1) 3 MSA20 SATA storage enclosure (SCSI bus 0, Box 5) Connecting SCSI storage enclosures In the following illustration, one dual-bus MSA30 SCSI storage enclosure is connected to the MSA1510i using two MSA SCSI I/O modules.
Connecting Ethernet cables To connect the MSA1510i to the network switch, use qualified Category 5e (or better) Ethernet cables. IMPORTANT: Make sure that the first connection to the network switch is from port 0 (top port) of the primary Ethernet iSCSI module. This port is configured to carry both management and iSCSI storage traffic.
Connecting Ethernet cables in a multipath configuration In the following illustration, additional items and cabling connections are needed in a multipath configuration. 1 Additional iSCSI Ethernet network switch 2 Additional MSA 2–Port Ethernet iSCSI module 3 Additional Ethernet cables for the redundant path Connecting power cords To protect your system from power-failure-related downtime, each MSA1510i ships standard with a redundant power supply.
Table 3 Levels of protection against power failure Connection method Level of protection MSA1510i power supplies connected to: Protects you from downtime when one of the MSA1510i power supplies fails. • One power source The remaining power supply/fan module can operate the MSA1510i until a replacement module is installed. MSA1510i power supplies connected to: Protects you from downtime when one of the MSA1510i power supplies fails.
Powering on the MSA 1. Verify that the following devices are powered on and in a ready state: • Uninterruptible Power Supplies (UPS) • Network switches 2. Power on all attached hard drive storage enclosures. IMPORTANT: Proceed to the next step only after confirming that the external storage enclosures have completed their startup routines; otherwise, the MSA array may not properly discover the storage. 3. Press and release Power On/Standby button on the front of the chassis to start up the MSA array.
Verifying the operating status of the devices To verify that your server, switches, MSA1510i, and attached storage enclosures are operating properly, view the device LEDs, and then compare them with the patterns described in the documentation for the devices. If the LEDs indicate a fault, see documentation that came with the device. For information about the MSA1510i, see the MSA1510i maintenance and service guide.http://h18006.www1.hp.com/products/storageworks/msa1510i.
MSA1510i component LED Condition Power supply module status LED Solid green = power is on. Fan control module status LED Solid green = power is on. 2-Port Ethernet iSCSI module status LED Solid green = power is on, the module is operational, and communication between the module and the controller is established. SCSI I/O module status LED Solid green = power is on. Reading startup messages on the controller display panel Each controller contains an integrated LCD panel.
Be sure to record the controller firmware version and management port IP address. (Basic MSA1510i information) IMPORTANT: Depending on the IP address automatically assigned to the MSA1510i, the MSA and its storage may be inaccessible to the network. If needed, change the IP address through the MSA controller LCD panel. For instructions, see “Changing the management port IP address through the MSA1510i controller display panel” on page 102.
Installation
4 Configuration Configuration includes: • MSA1510i supported management tools • Configuration best practices • Configuration overview • Configuring the Microsoft iSCSI initiator • Configuring the VMware iSCSI software initiator Supported management tools The following is a partial list of the tools that are supported for use with the MSA: • Storage Management Utility (SMU) overview • MSA Command Line Interface (MSA-CLI) overivew • HP Systems Insight Manager (HP-SIM) overview • Packet InterNet Groper (PING)
Sample tasks include: configuring iSCSI elements, setting up the management interface, configuring the logical units (LUNs), limiting access to the storage, viewing controller and storage setup, viewing status information, and running diagnostic reports. HP Systems Insight Manager (HP-SIM) overview HP Systems Insight Manager (HP-SIM) is a web-based application that allows system administrators to accomplish normal administrative tasks from any remote location, using a web browser.
Configuration best practices • Maintain detailed records of your iSCSI storage network, including information about the initiators, targets (including which LUNs are mapped to the targets), IP address assignments, and portals and portal groups. Be sure to note which initiators are accessing which targets through which portal groups using which IP addresses and protected by which Access Control List (ACL) and virtual Local Area Networks (VLAN).
Clean-up configuration tasks After initially configuring the host and MSA, to complete the configuration, be sure to: • • • • • • Check the SMU to ensure that all initiators have been added. Verify in the initiator software that the 1510i targets are present. Logon to the available targets. Ensure that the connection is automatically restored when the system boots. Set up security measures (ACLs, VLANS, and CHAP).
2. Enable discovery of the targets you want the initiator to access. NOTE: Multipath environments must enter access information for each path to the target. a. Select the Discovery tab. b. In the Target Portals section of the window, click Add.
c. Enter the IP address and TCP portal of the target on the primary controller, and then click OK. The display returns to the Discovery tab. (Example: 100.10.1.20:3260) d. In multipathing environments only, repeat step c to add the IP address and TCP portal of the target on the secondary controller. NOTE: As soon as one portal for the MSA is added to the Discovery tab, all portals for the MSA are automatically discovered by the initiator and will be displayed, whether access to them is permitted or not.
3. Configure target logon settings. a. On the Targets tab, select the first listing of the target, and then click Log On... b. Select the following options: • Automatically restore this connection when the system boots (optional). Each time this feature is selected, a login entry will be added to the Persistent Targets tab. Be careful not to select more than once per IP address and target. • Enable multi-path (Multipathing environments only) c. Click Advanced.
d. Expand the drop-down boxes and enter the following settings: • Local adapter: Microsoft iSCSI Initiator • Source IP: Enter the IP address of the NIC that has access to the target portal that you want to connect to (and will enter in the next step). • Target Portal: Select the destination target portal you want to connect to. (Example: 100.10.1.20:3260) IMPORTANT: Several Target Portal IP addresses may be presented. Be sure that the Source IP address and the corresponding Target Portal have a viable path.
f. View the display. It should now show a Status of Connected for that path to the target. NOTE: If the status is not Connected, do the following to eliminate one of the following common mistakes: • Make the second connection. • Verify that the Source IP address and the Target Portal are correct. 4. In multipathing environments only, repeat step 3 for the IP address and portal associated with the secondary controller. (Example: 100.30.1.
NOTE: In multipathing environments only, two sessions should be established: • one for the target portal associated with MSA controller A • one for the target portal associated with MSA controller B b. Select one of the listed sessions and then click Connections. c. View the information in the window and do the following: • Verify the target portal address. • Validate the IP address against the expected connection. d.
6. In multipathing environments only, test the redundancy by forcing a controller failover. (One method of forcing a failover is to disable the switch port associated with the active MSA controller path.) Troubleshooting Problem Possible cause / solution Microsoft iSCSI initiator cannot add a discovery portal The initiator name in the Microsoft iSCSI initiator software does not match the name entered for the initiator in the MSA1510i SMU or CLI.
Configuring the VMware iSCSI software initiator NOTE: Only iSCSI software initiators are supported by MSA1510i. This section describes how to configure the VMware iSCSI initiator to connect to a dual-controller MSA1510i in a multipathing environment. (For single-controller configurations, omit all steps shown for multipath or dual-controller configurations.) The initiator is native to ESX.
ESX Server supports the Challenge Handshake Authentication Protocol (CHAP) that your iSCSI initiators can use for authentication purposes. After your initiator establishes the initial connection with the target, CHAP verifies the identity of the initiator and checks a CHAP secret that your initiator and the target share. This can be repeated periodically during the iSCSI session. When configuring iSCSI initiators for your ESX Server system, make sure that CHAP is enabled.
3. To add a new iSCSI target that your ESX Server host can use for a SendTargets session, click Add. The Add Send Targets Server dialog box displays. 4. Enter the Send Targets server IP address, and click OK. 5. To change or delete a Send Targets server, select the server and click Edit or Remove. Setting up CHAP parameters for software initiators When configuring your iSCSI software initiator, make sure that CHAP parameters are enabled for the initiator. If they are not enabled, set them up.
3. To make any changes to the existing CHAP parameters, click Configure. The CHAP Authentication dialog box opens. 4. To keep CHAP enabled, make sure Use the following CHAP credentials is selected. 5. To use a new CHAP name, uncheck the Use initiator name check box, and enter the name of your choice. 6. If needed, specify the CHAP secret. All new targets will use the CHAP secret to authenticate the initiator. Any established sessions are not affected. 7. Click OK to save changes. 8. Perform a rescan.
NOTE: If you disable CHAP, all sessions that require CHAP authentication will end immediately. Performing a Rescan If a new LUN becomes accessible through the adapter, then ESX Server registers this new virtual device for use by virtual machines. If an existing LUN is no longer used and appears to be gone, then it is removed from use by virtual machines.
Troubleshooting Problem Possible cause / solution iSCSI initiator cannot add a discovery portal The initiator name in the iSCSI initiator software does not match the name entered for the initiator in the MSA1510i SMU or CLI. iSCSI initiator cannot connect to target portal iSCSI initiator connects to target portal but does not report any targets • • • • • • • Storage port with target portal is not connected to the network. Wrong IP address or TCP port number.
Configuration
5 Operation and management Some operation and management tasks include: • Powering off and powering on the MSA • Updating MSA firmware • Updating SCSI hard drive firmware • Recovering corrupted MSA controller firmware • Recognizing and recovering from hard drive failures and faulted LUNs • Adding or migrating hard drives, enclosures, and arrays • Changing the management port IP address through the MSA1510i controller display panel Powering off and powering on the MSA NOTE: Restarting (power cycling) the MS
Powering on the MSA 1. Verify that the following devices are powered on and in a ready state: • Uninterruptible Power Supplies (UPS) • Network switches 2. Power on all attached hard drive storage enclosures. IMPORTANT: Proceed to the next step only after confirming that the external storage enclosures have completed their startup routines; otherwise, the MSA array may not properly discover the storage. 3. Press and release the Power On/Standby button on the front of the chassis to start the MSA array.
Updating MSA firmware Firmware is a software program that resides in Read-Only Memory (ROM) on the device and is responsible for the behavior of the device. As part of a routine system maintenance program, it is important to periodically check the firmware versions installed throughout the system, including components on the server (operating system, drivers, software tools) and other network devices, including the MSA.
• MSA release notes and readme files 3. Identify items that need updating.
Updating MSA controller firmware CAUTION: The following methods are available for updating MSA array or storage enclosure firmware; select the method that best matches your environment: • Updating MSA firmware using the SMU • Updating MSA firmware using the MSA-CLI (most environments) Prerequisites Before updating system firmware, make note of the following: • When determining which MSA controller firmware version to use, review the requirements and information in the Compatibility Matrix(es), release note
IMPORTANT: If you encounter any problems during the firmware update process, stop and contact HP technical support. See for support contact information. Updating MSA firmware using the SMU NOTE: For complete information about accessing and using the SMU, see the HP Storage Management Utility user guide. 1.
7. From within the SMU, select Update > Controller > Flash Firmware. 8. Under the Flash Firmware banner, click Browse and navigate to the location of the previously-obtained firmware file, and then click OK. 9. Wait for a completion message to display.
11. View the messages displayed on the array controller LCD panel during startup to confirm that the firmware was installed successfully and that the array controller restarts successfully. NOTE: In dual-controller configurations, firmware on the two controllers is compared each time the MSA chassis is restarted. If the versions are mismatched, the system prompts to clone the firmware on the controller with the latest version over to the controller with the earlier version firmware.
2. Obtain the latest firmware files and save to a temporary location on the host: a. Navigate to the MSA1510i support page: http://www.hp.com/go/support. b. Click the title description of the download option to display important information about the update. • Click the Description tab for a brief overview about the download.
8. At the CLI prompt, enter the following command: CLI> download firmware where: offline —performs an update, but does not automatically restart the MSA; the MSA must be restarted manually. Can be used in single-controller and dual-controller configurations. online—performs an update with an automatic restart upon completion. Can be used in dual-controller configurations only. 9. On the menu bar at the top of the emulator window, select Transfer > Send File.
10. In the Send File window: a. Click Browse, navigate to the directory in which you placed the firmware files, and then select the firmware file. b. Expand the Protocol drop-down box, and then select 1K Xmodem. c. Click Send. A 1K Xmodem status window is displayed. 11. Wait for a completion message to display.
13. View the messages displayed on the array controller LCD panel during startup to confirm that the firmware was installed successfully and that the array controller restarts successfully. NOTE: In dual-controller configurations, firmware on the two controllers is compared each time the MSA chassis is restarted. If the versions are mismatched, the system prompts to clone the firmware on the controller with the latest version over to the controller with the earlier version firmware.
NOTE: There is the possibility that a specific version of firmware may not be compatible with certain hardware revisions of a controller. In this scenario, the firmware on the two controllers is compared, and the version that is compatible with both controllers is copied to the controller with the incompatible firmware version. However, if the controller that is updated is already operating and processing I/O, it is not reset.
5. Select Update > Storage System > Flash Firmware. 6. Under the Upload Inventory Firmware XML File banner, click Browse, navigate to the location of the previously-obtained XML firmware file, select an updating option, and then click OK. XML firmware filenames may be similar to the following: InventoryResultsLinux.xml 7. Wait for the MSA1510i to process the XML file and update the display with a list of all Smart Components that need updating. 8.
Recovering corrupted MSA controller firmware If the controller detects a firmware corruption, the following message is displayed on the LCD panel: ERROR: ROM CORRUPT SEND IMG VIA XMODEM To recover the controller, you must obtain a current firmware image and send it to the controller using a serial connection. 1. Go to the MSA1510i support website and obtain the latest controller firmware.
3. Using the emulator transfer (or send file) command, send the firmware to the controller. The following instructions and examples use HyperTerminal. For more information, see user documentation for your emulator program. a. On the menu bar at the top of the HyperTerminal window, select Transfer > Send File. b. Click Browse and navigate to the location of the firmware image obtained in step 1. c. Expand the Protocol drop-down box and select 1K XModem. d. Click Send. A status window is displayed. 4.
Recognizing and recovering from hard drive failures and faulted LUNs The purpose of fault-tolerant array configurations is to protect against data loss due to hard drive failure. Each RAID configuration has inherent limitations on the number of hard drive failures that it can tolerate. If the fault-tolerance level of a particular LUN or array configuration is exceeded, the array will be locked from any further I/O.
Compromised fault tolerance Each RAID configuration has inherent limitations on the number of physical hard drive failures that it can tolerate. If more hard drives fail than the fault-tolerance method allows, fault tolerance is compromised. When the MSA determines that the fault tolerance of a LUN is compromised, the LUN is taken offline and subsequent I/O requests are rejected. This is designed to protect the integrity of the LUN, but does require manual intervention to recover or re-enable the LUN.
6. If using the MSA LCD panel: a. If one of the following messages are displayed on the MSA array controller LCD front panel, an issue was found with one or more configured LUNs that may result in data loss, so all of the hard drives in the LUNs have been disabled. Press the right push button to re-enable the LUNs. 02 ENABLE VOLUME ? '<'=NO, '>'=YES 04 ENABLE VOLUMES ? '<'=NO, '>'=YES b. Make copies of important data, if possible. c.
• The priority that the rebuild is given over normal I/O operations (you can change the priority setting through the Array Configuration Utility (ACU), Storage Management Utility (SMU), or MSA Command Line Interface (MSA-CLI).
CAUTION: When replacing a hot pluggable hard drive, it is important that you follow the guidelines in this section. Failure to do so could result in data loss and could void your warranty.
4. Pull the hard drive out of the storage enclosure bay (3). Installing the hard drive NOTE: Illustrations in this section demonstrate installing a hard drive in an MSA20 storage enclosure. The procedure for installing a hard drive in an MSA30 or other storage enclosure is similar. 1. Press the hard drive ejector button (1) and pull the release lever to the full open position (2).
2. Slide the replacement hard drive into the same bay from which the old hard drive was just removed, making sure that the lever is in the full open position to ensure a correct latch. Then, push the hard drive into the bay as far as it will go, pressing firmly on the hard drive to make sure that it is seated properly (1). 3. Close the ejector lever against the front of the hard drive (2). 4. Verify that the hard drive is firmly engaged and that the ejector lever is latched.
Adding or migrating hard drives, enclosures, and arrays This section describes the following common migration scenarios: • Adding new hard drive storage enclosures • Migrating existing storage enclosures • Migrating the hard drives that make up an array NOTE: For the most up-to-date information on supported storage enclosures, see the MSA website. Adding new hard drive storage enclosures NOTE: New storage enclosures with unconfigured hard drives are hot pluggable.
1. Schedule a maintenance window to allow the storage subsystem to be turned off. 2. Ensure that a known, good backup is available. 3. From your management utility, such as the SMU, ACU, or MSA-CLI, generate a record of your current configuration. 4. If possible, power off all servers connected to the MSA array. Or, close all dependent applications. In MSA1510i configurations, be sure to use the initiator software to log off all MSA1510i targets. 5.
1. Power Off the MSA storage system as detailed in Powering off the MSA1510i. 2. Move the hard drives. 3. Power on the MSA storage system as detailed in Powering on the MSA. 4. The following message should be displayed on the LCD front panel of the controller 86 DRIVE POSITION CHANGE DETECTED. IMPORTANT: If the following LCD message is displayed: 121 NO VOLUMES DETECTED, turn off the system immediately to avoid data loss, and return the hard drives to their original locations. 5.
5. After all changes are entered, exit the management menu. Press v until Exit is displayed and blinking, and then press >. The LCD panel returns to the display mode. 6. Verify that the IP address was entered correctly by pressing ^ or v until the Port #MA0 IP message is displayed. 7. Verify that the server can locate the MSA1510i by opening a command prompt window and using the ping command.
Operation and management
6 MSA controller LCD panel message descriptions Included sections: • LCD panel overview • LCD message types • LCD message descriptions LCD panel overview Each array controller contains an integrated Liquid Crystal Display (LCD). This module is used for displaying informational and error messages, showing the status of the module, and for providing user input when required.
1 Fault LED—indicates an internal MSA component failure or external storage enclosure failure 2 Two-line, twenty-column text message LCD display panel 3 Left navigation button 4 Up navigation button 5 Right navigation button 6 Down navigation button 7 Redundancy Link LED (dual-controller configurations only)—indicates that both array controllers and their corresponding Fibre Channel I/O modules are in a redundant mode of operation LCD message types The display module is capable of holding up t
User input messages User input messages indicate that the system has encountered a situation that allows user input. The user can select from a number of choices. If the user does not select one of the choices in a set amount of time, the system selects the default setting. These user input messages only occur during system power on, and not during runtime.
Message Type Description Action An issue has been found with a configured volume that may result in data loss, so the volume has been disabled. The exact nature of the issue is detailed in a previous LCD display message. Yes = the volume is enabled (regardless of the issue). The volume attempts to return to its normal operating state and the data is accessible. No (or no input) = the volume remains disabled. The volume stays in the failed state and the data is not accessible.
Message Type Description Action User input In dual-controller configurations only, the array controller has detected a firmware version mismatch with the two controllers and wants to copy the firmware from the other controller onto this controller. Firmware on both controllers must match. Scroll through and read the messages on both controller LCD panels to confirm the currently installed firmware versions on the controller. Then, respond appropriately to the prompt. < = No, do not clone.
Message Type Description Action Error An online firmware update was successful, but a subsequent step failed. In dual-controller configurations, this may cause the other to not update properly. Restart the system. In dual-controller configurations, if the 07 CLONE FIRMWARE? '<'=NO, '>'=YES message is displayed, select >. 19 ONLINE UPGRADE REDUNDANCY HALTED Informational In dual-controller configurations, each controller restarts at least once during an online firmware update.
Message Type Description Action Error The MSA has a number of internal devices that are accessed via an I2C hardware bus. One of these devices failed when attempting to write to it. Certain I2C devices are considered critical and will result in a failure of the array controller, while others may result in some loss of functionality (such as lost display messages). If the issue persists, contact HP support.
Message 44 REDUNDANCY FAILED MISMATCH HARDWARE 45 REDUNDANCY FAILED MISMATCH FIRMWARE 46 REDUNDANCY HALTED EXPAND ACTIVE 47 REDUNDANCY FAILED CACHE SIZE MISMATCH 48 REDUNDANCY HALTED FIRMWARE CLONED 112 Type Description Action Error Both array controllers must contain the same hardware for them to successfully enter redundant mode. The current array controllers do not contain the same hardware, possibly because one has an attached Fibre Channel daughter card and the other does not.
Message 49 REDUNDANCY FAILED FIRMWARE LOCKUP 50 REDUNDANCY FAILED OUT OF MEMORY 51 REDUNDANCY FAILED I/O REQUEST ERROR 52 REDUNDANCY FAILED PCI BUS ERROR 53 REDUNDANCY FAILED NO SECOND CONTROLLER Type Description Action While either attempting to enter redundant mode or already operating in redundant mode, one of the array controllers encountered a critical condition resulting in a firmware lockup. Redundancy is disabled at this time.
Message Type Description Action Error The cache memory modules on the two controllers are not the same size. All cache memory modules must be the same size for redundancy to operate. Remove the array controller that has been halted, replace the cache modules with the appropriately sized ones, wait 10 seconds, and then reinsert the array controller, ensuring that it is fully seated in the chassis.
Message Type Description Action Error The cache memory has experienced a hardware failure. If the failure has occurred on the standby array controller, remove the standby array controller, replace the cache modules, wait 10 seconds, and then reinsert the array controller, ensuring that it is fully seated in the chassis. If the failure has occurred on the active array controller, wait until downtime is available.
Message 71 SYSTEM HALTED FOR CACHE ERROR 72 CACHE ERROR IGNORE? <=NO >=YES 116 Type Error User input Description Action This message is displayed upon a no response to message 72 CACHE ERROR IGNORE? <=NO >=YES . If = 1.1 or 1.2: There is currently only one cache module in the array controller, but the controller was previously configured with a second cache module that is now missing. If = 2.1 or 2.
Message Type Description Action If the failure occurred on the standby array controller, remove the standby array controller, remove cache, attach cache batteries, replace the cache modules, wait 10 seconds, and then reinsert the array controller, ensuring that it is fully seated in the chassis. If the failure occurred on the active array controller, wait until downtime is available.
Message Type Description 88 NON-HP DRIVE BOX #, BAY Informational An unsupported hard drive is located in the indicated bay of the storage enclosure. 89 INVALID CONFIG BOX #, BAY Error The indicated hard drive contains unrecognized configuration information from another system and therefore will not be used. Informational The configured volume has returned to its normal operating state. This typically occurs after a rebuild operation has completed.
Message 108 VOLUME # STATE MISSING DRIVES 109 VOLUME # STATE WRONG DRIVE REPLACED 110 VOLUME # EXPANSION DISABLED 111 VOLUME # INITIALIZING PARITY Type Description Action Error The configured volume is missing too many of the SCSI hard drives that it is composed of, making it unusable. The volume is disabled. Power off the MSA and then all attached storage enclosures. Unplug and reinsert all SCSI hard drives ensuring they are fully seated in their bays.
Message 121 NO VOLUMES DETECTED 122 NEW VOLUME(S) DETECTED 123 TOO MANY VOLUMES DETECTED 124 SPARES CLEARED 125 ACCESS CONTROL CONFLICT DETECTED 126 ACCESS CONTROL RESOURCES EXCEEDED 120 Type Description Action Informational No configured volumes were detected at power-up. If there are supposed to be configured volumes, power off the MSA and then all attached storage enclosures. Unplug and reinsert all SCSI hard drives ensuring they are fully seated in their bays.
Message 150 BEACON ON 151 BEACON OFF 201 ARRAY CONTROLLER TEMPERATURE OK 202 ARRAY CONTROLLER OVERHEATING 203 ARRAY CONTROLLER OVERHEATED Type Description Informational The LEDs on the MSA and all connected hard drives are blinking because that array controller was selected for identification or configuration in a host-based application such as the ACU or SMU.
Message 301 RECOVERY ROM AUTOFLASH DONE 302 RECOVERY ROM AUTOFLASH FAILED 303 ROM CLONING STARTED 304 ROM CLONING DONE 305 ROM CLONING FAILED 306 FIRMWARE FLASH STARTED 122 Type Description Informational The array controller has successfully completed the process of copying the current active firmware image into the backup recovery ROM. Error The array controller failed to copy the current active firmware image into the backup recovery ROM. Recovery ROM support is disabled.
Message Type Description 307 FIRMWARE FLASH DONE Informational The array controller in the MSA has completed the firmware flash process. It is now safe to restart the MSA and begin using the new firmware. In dual-controller configurations, the new firmware is cloned onto the other controller during the startup routine. 308 FIRMWARE FLASH FAILED Error The array controller in the MSA has failed the firmware flash process.
Message Type Description 319 FAN FLASH DONE ON BOX # Informational Indicates that the array controller has completed updating the firmware on a fan module. 320 FAN FLASH FAILED ON BOX # Error Indicates that the array controller was unable to update the firmware on a fan module. Retry the operation. Contact HP support if the problem persists.
Message Type Description Action The temperature in the specified storage enclosure is starting to exceed the normal operating range. Check all fans and ensure they are operating. Any failed fans should be replaced. Ensure that there is a module or blanking panel (cover plate) in all MSA chassis bays and slots. Empty bays affect the airflow and cooling ability of the MSA. Error The temperature in the specified storage enclosure has exceeded the safe operating range.
Message Type Description Action 450 INVALID SCSI CABLING BOX # Error The MSA has detected an external storage enclosure that is cabled incorrectly. Verify that the external storage enclosures are connected properly to the MSA. For more information, see the MSA installation guide. 500 INITIALIZING PCI SUBSYSTEM Informational The array controller's PCI subsystem is being initialized as part of the power up sequence.
Message Type Description 522 INITIALIZING ISCSI SUBSYSTEM Informational The iSCSI subsystem is being initialized as part of the power-on sequence. 523 LOADING ISCSI PARAMS Informational The iSCSI configuration is being loaded into the iSCSI hardware as part of the power-on sequence. 524 ISCSI MODULE HARDWARE FAILURE Error The array controller has detected a hardware failure in the iSCSI daughter board. Contact HP support.
Message Type Description Action 608 PORT CONFLICT Error The MSA has detected an IP address conflict with another device on the network. Reconfigure the MSA to use an unused IP address, or remove the conflicting device from the network. 611 PROCESSOR REV Informational The detected MSA processor revision. Error The array controller has detected a 10 Mb/s link on the indicated Ethernet port. The MSA1510i does not support 10 Mb/s, so communication with this port is not possible.
A Regulatory compliance and safety Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
For questions regarding your product, contact: Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800- 652-6672 For questions regarding this FCC declaration, contact: Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product.
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1 1976. Compliance is mandatory for products marketed in the United States. International notices and statements Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Japanese notice Korean notice (A&B) Class A equipment Class B equipment Safety Battery replacement notice WARNING! The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60C (140F).
Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP Partner, or their agents. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider.
• • • • Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. Place parts on a grounded surface before removing them from their containers. Avoid touching pins, leads, or circuitry. Always be properly grounded when touching a static-sensitive component or assembly. Grounding methods There are several methods for grounding.
Dutch notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.
French notice Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques.
újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, valamint biztosítja a selejtezett termékek környezetre és emberi egészségre nézve biztonságos feldolgozását. A begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat.
naturalnych i zapewnią ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty sprzęt do recyklingu, należy się skontaktować z urzędem miasta, zakładem gospodarki odpadami lub sklepem, w którym zakupiono produkt. Portuguese notice Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum.
contribuirá a conservar los recursos naturales y a garantizar el reciclado de estos residuos de forma que se proteja el medio ambiente y la salud. Para obtener más información sobre los puntos de recogida de residuos eléctricos y electrónicos para reciclado, póngase en contacto con su ayuntamiento, con el servicio de eliminación de residuos domésticos o con el establecimiento en el que adquirió el producto.
Regulatory compliance and safety
B MSA1510i worksheets Use these worksheets to record information about your MSA1510i. NOTE: These worksheets are not prerequisites for installing your MSA1510i, but some of the information is required for initial setup and configuration, and some of the information may be helpful for future configuration changes and troubleshooting purposes.
Table 8 Basic MSA1510i information Component Configuration type (check one) Settings Single-path, non-clustered servers Single-path, clustered servers Multipath, non-clustered servers Multipath, multiple clustered servers MSA1510i chassis serial number ____________________________________ Controller firmware version, installed ____________________________________ Controller firmware version, Web ____________________________________ Installation CD version shipped ___________________________________
Table 9 MSA1510i 2-Port Ethernet iSCSI module IP address information Component Settings Primary Ethernet iSCSI module, for the controller in slot 1: Location: Rear-left of the MSA1510i Physical port 0 (top port) Logical port SA0 IP address / VLAN ID ________________________ / __________ TCP port ____________________________________ TCP port ____________________________________ IP address / VLAN ID ________________________ / __________ TCP port ____________________________________ TCP port ___
MSA1510i 2–Port Ethernet iSCSI module IP address information (continued) Component Settings Redundant module, for the controller in slot 2 Location: Rear-right of the MSA1510i Physical port 0 (top port) Logical port SB0 IP address / VLAN ID ________________________ / __________ TCP port ____________________________________ TCP port ____________________________________ IP address / VLAN ID ________________________ / __________ TCP port ____________________________________ TCP port ____________
Table 10 Network switch information Component Setting Make and model ____________________________________ Capability (100BaseT, 1000BaseT) ____________________________________ VLAN ID ____________________________________ LAN segment IP address ____________________________________ VLAN ID ____________________________________ LAN segment IP address ____________________________________ VLAN ID ____________________________________ LAN segment IP address ____________________________________ An
Table 11 Server information Component Settings Make and model ____________________________________ Operating system, version ____________________________________ Service pack and patch kit ____________________________________ Server name ____________________________________ iSCSI qualified name (iQN) ____________________________________ VLAN ID ____________________________________ 100/1000BaseT NIC model ____________________________________ NIC slot number/port number ______________________
Server information (continued) Component Settings An additional server: Make and model ____________________________________ Operating system, version ____________________________________ Service pack and patch kit ____________________________________ Server name ____________________________________ iSCSI qualified name (iQN) ____________________________________ VLAN ID ____________________________________ 100/1000BaseT NIC model ____________________________________ NIC slot number/port numbe
Server information (continued) Component Settings An additional server: Make and model ____________________________________ Operating system, version ____________________________________ Service pack and patch kit ____________________________________ Server name ____________________________________ iSCSI qualified name (iQN) ____________________________________ VLAN ID ____________________________________ 100/1000BaseT NIC model ____________________________________ NIC slot number/port numbe
Server information (continued) Component Settings An additional server: Make and model ____________________________________ Operating system, version ____________________________________ Service pack and patch kit ____________________________________ Server name ____________________________________ iSCSI qualified name (iQN) ____________________________________ VLAN ID ____________________________________ 100/1000BaseT NIC model ____________________________________ NIC slot number/port numbe
Table 12 Array and unit information Array 150 Unit # RAID level MSA1510i worksheets Disk members Unit capacity nl Drive type (SCSI/SATA) Spare
Table 13 Target information Target Units LUNs IP address/subnet/port MSA portal/portal group/logical port Table 14 Initiator access information Server name iQN name Initiator alias Assigned target VLAN ID 1510i Modular Smart Array installation and user guide 151
MSA1510i worksheets
Index Symbols data recovery, automatic, 95 2-Port Ethernet iSCSI module LEDs, 27 A audience, 9 automatic data recovery rebuild, 95 B battery replacement and recycling notices, 132 best practices cabling, general, 47 Ethernet cables, 51 installing the MSA1510i, 34 iSCSI, 17 performance, 51 racking, 41 box number assignments, 47 bus number assignments, 47 C cables best practices, 47 cable management considerations, 47 connecting Ethernet cables, multipath, 52 connecting Ethernet cables, single path, 51
cache hardware enabled, 114 cache hardware temporarily disabled, 115 cache module size, 114 chassis nvram contents corrupted, 111 clone firmware, 109 cloning refused system halted, 109 configured volumes, 119 controller too old not supported, 109 critical lockup detected, 108 drive failure box, bay, 117 drive hot added box, bay, 117 drive hot removed box, bay, 117 drive position change detected, 117 drive position change invalid, 117 dual cache module size mismatch, 114 ecc corrected memory error seen, 126
conventions document, 10 text symbols, 10 converting rack rails for round-hole racks, 42 corrupted firmware recovering, 91 registering, note, 91 customer self repair, 11 D declaration of conformity, 129 device preparation removing power, 77 diagnostic tools, 59 diagrams connecting SCSI cables to SATA enclosures, 50 connecting SCSI cables to SCSI enclosures, 50 front panel, 14, 19 power supply LEDs, 30 rear panel, 15, 20 SCSI I/O module LEDs, 29 shipping contents, 16 document conventions, 10 prerequisites,
volume rebuild failure, 119 volume state disabled, 118 volume state failed, 118 volume state missing drives, 119 volume state wrong hard drive replaced, 119 Ethernet cables connecting, 51 recommendation, 51 F fan module LEDs, 28 fan modules, 28 fault tolerance, removing hard drives, 97 FCC logo, 129 Federal Communications Commission notice, 129 fimware accessing the SMU to update, note, 82 firmware cloning, 88 cloning in redundant configurations, 78, 78 ISO images, 82, 85 MSA controller updating, 79 obtai
initializing PCI subsystem, 126 initializing redundancy support, 111 initializing SCSI subsystem, 110 initializing subsystem, 110 initializing target-based mgmt, 127 iSCSI module flash done, 123 iSCSI module flash started, 123 loading iSCSI params, 127 management port disabled, 127 management port enabled, 127 new volume(s) detected, 120 no volumes detected, 120 non-compaq hard drive, 118 obsolete cache data deleted, 115 online upgrade complete, 109 online upgrade flashing done, 109 online upgrade f
M management mode controller display, 60 management port IP address changing , 102 message descriptions LCDs, 107 MSA controller updating the firmware, 81 MSA controller firmware overview, 79 updating, 79 prerequisites, 81 updating using the SMU, 82 MSA1510i overview, 13 MSA1510i compatibility guide website, 46 MSA1510i controller LEDs, 22 MSA1510i controller display panel changing management port IP address, 102 MSA1510i information iSCSI concepts and deployment guide, 31 MSA1510i worksheet, 142 multipath
regulatory compliance, 129 information number, 130 notices HP series number, 130 related documentation, 9 replacing hard drive, 96 ROM cloning, 88 S Systems Insight Manager overview, 60 T safety notices, 132 SAN Infrastructure website, 34 scrolling, 105 SCSI cables, connecting, 40, 47 SCSI connections, supported and unsupported, 49 SCSI I/O module LEDs, 29 SCSI I/O module, installing, 40 securing the system to the rack, 45 series number, regulatory compliance, 130 server at MSA1510i startup, 55 preparin
websites clustering, 34 customer self repair, 11 enclosures, 34 HP , 12 HP documentation, 9 HP Subscriber’s Choice for Business, 12 infrastructure, 34 Insight Manager, 34 MSA1510i, 9, 34 multipathing, 34 OS information, 10 related information, 9 servers, 34 Subscriber's Choice, 34 switches, 34 warranty information, 11 160 weight considerations, 36 worksheets, 141 basic MSA1510i information, 142 IP address information, 143 server information, 146 storage information, 150 switch information, 145 target info