HP StorageWorks 1510i Modular Smart Array maintenance and service guide Part number: 383072–002 Second edition: May 2008
Legal and notice information © Copyright 2005, 2008 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . Intended audience . . . . . . . Prerequisites . . . . . . . . . Related documentation . . . . . Document conventions and symbols Rack stability . . . . . . . . . HP technical support . . . . . . Customer self repair . . . . . . Subscription service . . . . . . HP websites . . . . . . . . . . Documentation feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Returning the defective component . . . . . . Recommended tools . . . . . . . . . . . . . . Warnings and precautions . . . . . . . . . . . Electrostatic discharge information . . . . . . Grounding methods . . . . . . . . . . . . Equipment symbols . . . . . . . . . . . . . Weight warning . . . . . . . . . . . . . . Rack warnings and precautions . . . . . . . Device warnings and precautions . . . . . . Determining whether a component is hot-pluggable . Powering off and powering on the MSA . . . . . .
Installing the power supply module . . . . . . . Verifying proper operation . . . . . . . . . . Replacing the MSA1510i chassis . . . . . . . . . . Before you begin . . . . . . . . . . . . . . Verifying component failure . . . . . . . . . . Removing the chassis components . . . . . . . Prepare for the replacement . . . . . . . . Remove the 2-Port Ethernet iSCSI I/O modules Remove the fan modules . . . . . . . . . Remove the SCSI I/O modules . . . . . . . Remove the power supply modules . . . . .
Latvian notice . . Lithuanian notice Polish notice . . Portuguese notice Slovakian notice . Slovenian notice . Spanish notice . Swedish notice . . . . . . . . . 77 78 78 78 78 79 79 79 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this guide This guide provides information about: • Maintaining the MSA1510i • Servicing the MSA1510i • Troubleshooting the MSA1510i WARNING! To reduce the risk of personal injury from electric shock and hazardous energy levels, do not exceed the level of repairs specified in these procedures. Troubleshooting and repair procedures included in this document are detailed to allow only subassembly/module-level repair.
In addition to MSA1510i-specific documents, the following guide, available on the SAN Infrastructure website: http://www.hp.com/go/san, includes detailed, helpful information about Fibre Channel and iSCSI networks: • HP SAN Design reference guide The following iSCSI-related technical information is available on the Internet Engineering Task Force website: http://www.ietf.org/rfc.
TIP: Provides helpful hints and shortcuts. Rack stability WARNING! To • • • • • reduce the risk of personal injury or damage to equipment: Extend leveling jacks to the floor. Ensure that the full weight of the rack rests on the leveling jacks. Install stabilizing feet on the rack. In multiple-rack installations, secure racks together. Extend only one rack component at a time. Racks can become unstable if more than one component is extended.
• • • • • • http://www.hp.com/go/storage http://www.hp.com/go/servers http://www.hp.com/service_locator http://www.hp.com/support http://www.hp.com/support/manuals http://www.hp.com/support/downloads Documentation feedback HP welcomes your feedback. To make comments and suggestions about product documentation, please send a message to StoragedocsFeedback@hp.com. All submissions become the property of HP.
1 Illustrated parts list This section provides an illustrated parts breakdown and spare parts list for the HP StorageWorks 1510i Modular Smart Array (MSA1510i).
7 MSA1510i controller with 256 MB cache module and batteries 417787–001 AD539–04001 Optional 8 MSA controller blanking panel 229208–001 n/a Mandatory AC power cords Contact HP Support Contact your HP Authorized Reseller Mandatory Custom serial cable for CLI connection 316131–001 n/a Mandatory SCSI hard drives Contact HP Support Contact your HP-authorized reseller Optional SATA hard drives Contact HP Support Contact your HP-authorized reseller Optional Cache module (256 MB) with bat
2 Specifications This section provides operating and performance specifications for the MSA1510i. Included in this section: • Chassis specifications • 2-Port Ethernet iSCSI module specifications • Fan module specifications • SCSI I/O module specifications • Power supply module specifications NOTE: For additional information on components and their part numbers, see Illustrated parts list.
Chassis specifications Parameter Value Height 8.79 cm (3.46 in) Width 48.41 cm (19.06 in) Depth 61.77 cm (24.32 in) Weight 24.95 kg (55 lb) Input voltage requirements Rated input voltage 100 to 240 VAC Rated input frequency 50 Hz to 60 Hz Rated input current 6.
Fan module specifications Parameter Value Height 6.0 cm (2.36 in) Width 6.0 cm (2.36 in) Depth 26.8 cm (10.6 in) Weight 0.50 kg (1.10 lbs) SCSI I/O module specifications Parameter Value Height 8.13 cm (3.2 in) Width 2.34 cm (0.92 in) Depth 37.14 cm (14.62 in) Weight 0.46 kg (1.01 lbs) Power supply module specifications Parameter Value Height 7.7 cm (3.0 in) Width 6.4 cm (2.5 in) Depth 32.0 cm (12.6 in) Weight 1.80 kg (3.
Specifications
3 System components and LEDs This chapter includes figures and tables that identify system components and describe chassis and module LEDs patterns. • Front view • Rear view • Chassis and component LEDs Front view 1. Chassis LEDs 2. Chassis Power On/Standby button 3. Blank for an additional controller (controller slot 2) 4. MSA1510i controller (controller slot 1) 5. Controller LCD message display panel 6.
Rear view 1. 2–Port Ethernet iSCSI module (for the controller in slot 1) 2. Chassis slot diagram 3. Blank for additional 2-Port Ethernet iSCSI module (for the controller in slot 2) 4. Power supply module 2 5. Power supply module 1 6. SCSI I/O module (bus 0) 7. Blank for additional SCSI I/O module (bus 1) 8. Fan module 2 9. Fan module 1 10. Blank for additional SCSI I/O module (bus 2) 11. Blank for additional SCSI I/O module (bus 3) 12. Unused slot NOTE: Each MSA SCSI I/O module has two ports.
Chassis and component LEDs The MSA chassis and its modular components are equipped with LEDs. When the fault LED on any MSA component is amber, promptly determine the reason for the alert by examining the component, the messages displayed on the MSA controller LCD panel, and system event logs (such as those provided by HP Systems Insight Manager). The following sections define the LEDs.
NOTE: System power does not shut off completely with the power button. Standby removes power from most of the electronics and the hard drives, but portions of the power supply and some internal circuitry remain active. To remove the power completely, disconnect all power cords from the device. For instructions, see “Powering off the MSA1510i” on page 38. Controller LEDs During normal runtime, the array controller has 18 LEDs that indicate controller activity or malfunction.
Item Name Condition Color Meaning 1 SCSI bus 3 activity On Green There is activity on this SCSI bus. 2 SCSI bus 2 activity On Green There is activity on this SCSI bus. 3 SCSI bus 1 activity On Green There is activity on this SCSI bus. 4 SCSI bus 0 activity On Green There is activity on this SCSI bus. 5 Logical I/O activity On Green Requests from the host are being processed. 6 Direct Memory Access activity On Green Direct Memory Access transfers are active.
Item 1 Activity LED On Item 2 Online LED Off Blinking Off Blinking Off Item 3 Fault LED Meaning Off The hard drive is being accessed in one of the following ways: • The hard drive is not configured as part of an array. • The hard drive is a replacement and rebuild has not yet started. • The hard drive is spinning up during POST. Do not remove the hard drive. Removing a hard drive at this time could terminate the current operation and cause data loss.
SATA hard drive LEDs Each SATA hard drive has two LEDs. The following figure and table describe their locations and meanings. Item 2 Fault/ UID LED (amber/ blue) Meaning On, off, or blinking Alternating amber and blue The drive has failed, or a predictive failure alert has been received for this drive; it also has been selected by a management application. On, off, or blinking Steadily blue The drive is operating normally and has been selected by a management application.
Slot diagram LEDs Located on the rear of the MSA, the slot diagram provides information about MSA modules. 1. 2–Port Ethernet iSCSI module (for the controller in slot 2) 2. SCSI I/O module (bus 3) 3. SCSI I/O module (bus 2) 4. Fan module 1 5. Fan module 2 6. 2–Port Ethernet iSCSI module (for the controller in slot 2) 7. SCSI I/O module (bus 1) 8. SCSI I/O module (bus 0) 9. Power supply 1 10.
2-Port Ethernet iSCSI module LEDs The 2-Port Ethernet iSCSI module has one LED to show the status of the module, and each port has two LEDs to show status and activity information for the specific port. Item 1 2 3 Name Module status Port status Port activity Color Meaning Solid Green Power is on, the module is operational, and communication between the module and the controller is established. Blinking Amber Power is on, but there is no communication to the controller.
Fan module LEDs Each fan module has one bi-color LED. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Fault Condition Color Meaning Solid Green The power is on. Off — The power is off. Blinking Amber A fault was detected in this module. Fan modules cool the chassis by circulating air through the enclosure. The rate at which air moves (the airflow) determines the amount of cooling.
SCSI I/O module LEDs The SCSI I/O module has two LEDs. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Condition Color Description Solid Green The power is on. Off — The power is off. Blinking Green There is activity on this SCSI module. Off — There is no activity on this SCSI module.
Power supply module LEDs The power supply uses a single bi-color LED to indicate status. This LED can be illuminated with either a green or amber color. The following figure and table describes their locations and meanings. Item Name 1 Status 2 Fault 28 Condition Color Description Solid Green The power is on. Off — The power is off. Blinking Amber A fault was detected on this module.
4 Available diagnostic tools The following is a partial list of tools that are supported for use with the MSA: • Storage Management Utility (SMU) overview • MSA Command Line Interface (MSA-CLI) overivew • HP Systems Insight Manager (HP-SIM) overview • Packet InterNet Groper (PING) overview • MSA array controller LCD panel Storage Management Utility (SMU) overview The Storage Management Utility (SMU) is integrated in the MSA array controller firmware and offers a graphical user interface (GUI) application f
third-party devices. HP-SIM reports hardware fault conditions (both failure and pre-failure) and collects data for reporting and graphing. HP-SIM also provides base-level management of HP clients, printers, and selected storage. HP recommends using HP-SIM to monitor the performance of your Windows, Linux, and NetWare systems. IMPORTANT: You must install and use HP-SIM to benefit from the Pre-Failure Warranty for processors, SAS, SCSI, and SATA hard drives, and memory modules.
5 Customer replaceable components This chapter includes the following information regarding the removal and replacement of MSA components: • Procedural overview • Customer self repair • Recommended tools • Warnings and precautions • Determining whether the component is hot-pluggable • Powering off and powering on the MSA • Removing or installing an interconnect blank • Removing or installing a hard drive blank • Replacing a hard drive • Replacing the controller, controller cache, or controller battery • Rep
Verification procedures may include: • Viewing status and error messages sent to the controller LCD panel. • Viewing the LED illumination patterns on the MSA and the component. • Viewing system event logs or other reports generated by system-management tools, such as HP-SIM. Customer self repair HP products are designed with many Customer Self Repair (CSR) components to minimize repair time and allow for greater flexibility in performing defective parts replacement.
billing you for the replacement. With a CSR, HP will pay all shipping and part return costs and determine the courier/carrier to be used.
If you do not have any of the suggested equipment for proper grounding, have an Authorized HP Reseller install the part. NOTE: For more information on static electricity or assistance with product installation, contact your HP Authorized Reseller. Equipment symbols The following symbols may be located on equipment in areas where hazardous conditions may exist. WARNING! Any enclosed surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards.
Weight warning WARNING! The device can be very heavy. To reduce the risk of personal injury or damage to equipment: • Remove all hot-pluggable power supplies and modules to reduce the overall weight of the device before lifting. • Observe local health and safety requirements and guidelines for manual material handling. • Get help to lift and stabilize the device during installation or removal, especially when the device is not fastened to the rails. When a device weighs more than 22.
WARNING! Verify that the AC power supply branch circuit that provides power to the rack is not overloaded. Overloading AC power to the rack power supply circuit increases the risk of personal injury, fire, or damage to the equipment. The total rack load should not exceed 80 percent of the branch circuit rating. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.
CAUTION: To properly ventilate the system, you must provide at least 7.6 centimeters (3.0 inches) of clearance at the front and back of the device. CAUTION: When replacing hot-pluggable components in an operational MSA, allow approximately 30 seconds between removing the failed component and installing the replacement. This time is needed to ensure that configuration data about the removed component is cleared from the system registry. To minimize airflow loss, do not pause for more than a few minutes.
Component Hot-pluggable Redundant power supply module X Redundant fan module X MSA array controller (dual–controller configurations) nl X* 2–Port Ethernet iSCSI module (dual–controller configurations) X* nl SCSI I/O module Non- hot-pluggable X MSA chassis X MSA array controller (single–controller configurations) X 2–Port Ethernet iSCSI module (single–controller configurations) X MSA array controller (single–controller configurations) X nl * Before removing one of the two controllers o
5. Verify that the Power on/Standby button LED is amber/off and that the fans are off. 6. Power off all attached hard drive enclosures. 7. Disconnect the power cords from the MSA. Powering on the MSA 1. Verify that the following devices are powered on and in a ready state: • Uninterruptible Power Supplies (UPS) • Network switches 2. Power on all attached hard drive storage enclosures.
Removing or installing a 2-Port Ethernet iSCSI blank Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
Removing or installing a hard drive blank Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
Replacing a hard drive Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
• Do not remove a failed second hard drive from an array until the first failed or missing hard drive has been replaced and the rebuild process is complete. (When the rebuild is complete, the online LED on the front of the hard drive stops blinking.) Exceptions: • In RAID 6 (ADG) configurations, any two drives in the array can be replaced simultaneously. • In RAID1+0 configurations, any drives that are not mirrored to other removed or failed drives can be simultaneously replaced offline without data loss.
3. Press the ejector button (1) and pull the release lever to the full open position (2). IMPORTANT: Wait approximately 10 seconds for the internal disk to stop spinning before pulling the hard drive out of the enclosure. Handling a hard drive while the internal media is spinning can damage the media. 4. Pull the hard drive out of the storage enclosure bay (3). Installing the hard drive NOTE: Illustrations in this section demonstrate installing a hard drive in an MSA20 storage enclosure.
2. Slide the replacement hard drive into the same bay from which the old hard drive was just removed, making sure that the lever is in the full open position to ensure a correct latch. Then, push the hard drive into the bay as far as it will go, pressing firmly on the hard drive to make sure that it is seated properly (1). 3. Close the ejector lever against the front of the hard drive (2). 4. Verify that the hard drive is firmly engaged and that the ejector lever is latched.
Replacing the controller, controller cache, or controller battery The following sections detail procedures for replacing an MSA array controller, controller cache module, or controller cache battery pack: • Before you begin • Verifying component failure • Removing the controller • Removing the controller cache module • Removing the controller cache battery pack • Installing the controller cache battery pack • Installing the controller cache module • Installing the controller • Verifying the replacement Perf
Verifying component failure Before replacing the controller, cache module, or battery pack: • Check the controller LCD display panel for error messages. • Record any Failure LEDs or LCD panel messages for reference purposes. • Check the controller Heartbeat LED (1) . If the LED is not blinking, it might indicate a failure. • Check the controller Fault LED (2) . If the LED is on, it might indicate a failure. Removing the controller 1.
• and you are replacing a cache module with another module of the same size, you can remove one of the controllers and replace the module on that controller while the system is running. • and you are replacing a cache module with a module of a different size, you must schedule a maintenance window and remove power from the system to then change the cache module on both controllers at the same time. The memory size of the cache modules must be the same on both controllers.
CAUTION: Do not dispose of batteries, battery packs, and accumulators with general household waste. Use the public collection system or return them to HP, your authorized HP Partners, or their agents. NOTE: • Always replace batteries in pairs, not individually. • Temperature, age, and cache size can affect battery life. This time span also applies if the controller cache module is removed from the array controller.
5. Lift the pack upward to unhook the top of the battery pack. 6. Wait approximately 15 seconds after removing the old battery to allow the battery charge monitor to reset. NOTE: If you do not wait 15 seconds after removing the old battery, full charge of the new cache battery is delayed. 7. Repeat step 3 through step 6 to remove the second battery pack on this cache module. Installing the controller cache battery pack 1. Remove the array controller as instructed in Removing the controller. 2.
6. Verify that the top hook (1) and bottom clip (2) on the battery pack are securely attached to the cache module. 1 2 15520 7. Repeat step 4 through step 6 to install the second battery pack on the module. 8. Install the serviced cache module in the controller as instructed in Installing the controller cache module. NOTE: The cache is disabled while the batteries are charging and is automatically re-enabled after the batteries are fully charged. Installing the controller cache module 1.
Installing the controller 1. Insert the new or serviced array controller into the MSA chassis controller bay (1). 2. Push the controller in as far as it will go, making sure that the controller is seated, and then press the latch handle inward until it is flush against the front panel (2). 1 2 15493 3. If necessary, power on the MSA as instructed in Powering on the MSA.
Replacing a 2-Port Ethernet iSCSI module Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
3. Lift the port-colored 2-Port Ethernet iSCSI module latch (1) and pull the module out of the enclosure (2). Installing the 2-Port Ethernet iSCSI I/O module 1. Slide the replacement 2-Port Ethernet iSCSI module into the MSA chassis bay until the module clicks into place. 2. Reconnect the cables. Verifying proper operation After replacing the failed 2-Port Ethernet iSCSI module verify that: • The 2-Port Ethernet iSCSI module status LED is solid green.
Replacing a fan module The variable-speed fan module is hot-pluggable, so it is not necessary to power down the system to replace it. Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
15210 Verifying proper operation After replacing the fan module, verify that: • The fan starts operating immediately. • The fan Status LED is On. • No new error messages are displayed on the array controller LCD panel.
Replacing a SCSI I/O module Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
3. Lift the port-colored SCSI I/O module latch (1) and pull the SCSI I/O module out of the chassis (2). Installing the SCSI I/O module 1. Slide the replacement SCSI I/O module into the MSA chassis bay until the module clicks into place. 2. Reconnect all SCSI cables. NOTE: Ensure that all of the SCSI cable connectors are fastened tightly. Verifying proper operation After replacing the failed SCSI I/O module, verify that: • The SCSI I/O module Status LED is solid green.
Replacing a power supply module The power supply is hot pluggable, so it is not necessary to power down the system to replace it. Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device.
Installing the power supply module 1. Slide the replacement power supply module into the MSA chassis bay until the module clicks into place. 2. Connect the AC power cord to the power supply. Verifying proper operation After replacing the power supply, verify that: • The power supply Status LED is solid green. • No new error messages are displayed on the array controller LCD panel.
Replacing the MSA1510i chassis When replacing a chassis, components are removed from the failed chassis and then installed in the replacement. Components that are moved include the following: • 2-Port Ethernet iSCSI modules • Fan modules • SCSI I/O modules • Power supply modules • Controllers • Blanks Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available.
Removing the chassis components Prepare for the replacement 1. Review all warnings, cautions, and preparation procedures as detailed in Warnings and precautions. 2. If the MSA is operational, stop all access to the MSA. 3. Press and hold the Power on/Standby button for five seconds to place the MSA in Standby mode. 4. Label each cable carefully and then disconnect all of the cables. Remove the 2-Port Ethernet iSCSI I/O modules 1. Lift the port-colored latch and pull the module out of the chassis. 2.
Remove the SCSI I/O modules 1. Lift the port-colored latch and pull the module out of the chassis. 2. Remove all other SCSI I/O modules or blanks. Remove the power supply modules 1. Press the port-colored latch towards the side of the module and pull the module out of the chassis. 2. Remove the other module. Remove the controllers 1. Press the controller thumb latch to release the latch handle, and then rotate the latch handle out.
2. Grasp the latch handle and pull the controller out of the chassis. 3. Remove the other controller or blank. Remove the MSA from the rack 1. Remove the decorative bezel from the front of the MSA by grasping the outside edges and pulling with sufficient force to disengage the retaining clips. 2. Loosen the thumbscrews securing the MSA to the front of the rack, and then slide the MSA out of and away from the rack.
2. Attach the decorative bezel on the front of the MSA by aligning the pins and retaining clips on the back of bezel with the corresponding locations on the front of the chassis. Then, with even pressure, push firmly on the bezel until the retaining clips engage. Install the controllers 1. Press the controller thumb latch and rotate the latch handle out. 1 2 15493 2. Slide the controller into the chassis and then push firmly to ensure a good seat. 3.
Install the SCSI I/O modules 1. Slide the module into the chassis SCSI I/O slot until the latch clicks into place. 2. Install all other SCSI I/O modules or blanks. Install the fan modules 1. Slide the module into the chassis fan slot until the latch clicks into place. 2. Install the other fan module.
Install the 2-Port Ethernet iSCSI I/O modules 1. Slide the module into the chassis network interconnect slot until the latch clicks into place. NOTE: The following illustration demonstrates installing a Fibre Channel I/O module in the chassis. For the MSA1510i, the 2–Port Ethernet iSCSI I/O module is in this slot. 2. Install the other I/O module or blank. Completing the replacement 1. Reconnect the AC power cords to the MSA. 2. Reconnect the SCSI and Fibre Channel (or Ethernet) cables to the MSA chassis.
5. Read the controller LCD panel messages during the MSA startup routine. • If the following messages are displayed, the serial number of the original chassis was automatically transferred to the replacement chassis. SPARE CHASSIS DETECTED CHASSIS SERIAL NUMBER FLASHED UPDATED IMPORTANT: If these messages are displayed, the MSA1510i will automatically restart. • If the following message is displayed, it may safely be ignored.
A Regulatory compliance and safety Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
For questions regarding your product, contact: Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800- 652-6672 For questions regarding this FCC declaration, contact: Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product.
International notices and statements Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Japanese notice Korean notice (A&B) Class A equipment Class B equipment 72 Regulatory compliance and safety
Safety Battery Replacement notice WARNING! The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60C (140F). • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Electrostatic discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: • • • • • Avoid hand contact by transporting and storing products in static-safe containers.
místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na příslušném obecním nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v obchodě, kde jste produkt zakoupili.
See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda.
Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριμένο προϊόν δεν πρέπει να διατίθεται μαζί με τα άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη να απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον σε καθορισμένο σημείο συλλογής για την ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού.
Lithuanian notice Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir elektroninės įrangos atliekoms perdirbti.
Slovenian notice Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv način.
Regulatory compliance and safety
Index Symbols bezel part numbers, 11 2-Port Ethernet iSCSI module LEDs, 25 part numbers, 11 replacing, 53 specifications, 14 A AC circuit overload, warning, 36 AC power cord part numbers, 12 audience, 7 B batteries installing, 50 warnings, 48 battery verifying failure, 47 best practices replacing a hard drive, 42 C cables, 70 cache battery pack, replacing, 48 module, installing, 51 module, replacing, 47 cache battery kit part numbers, 12 cache module part numbers, 12 verifying failure, 47 cautions th
electrostatic sensitive parts handling, 33 packaging, 33 storing, 33 transporting, 33 ESD (electrostatic discharge) precautions, 33 preventing, 33 F fan module installing, 55 LEDs, 26 part numbers, 11 proper operation, 56 removing, 55 replacing, 55 specifications, 15 verifying failure, 55 fault tolerance, removing hard drives, 43 FCC logo, 69 firmware cloning in redundant configurations, 39 mismatched, 39 G grounding methods, 33 procedures, 33 H hard drive blank, removing, 41 blank, replacing, 41 ejec
MSA1510i illustrated parts breakdown and spare parts list, 11 powering off and on, 38 MSA1510i powering off, 20 MSA1510i chassis replacement preparation, 62 removal, 62 replacing components, 61 serial numbers, 64 verifying failure, 61 MSA1510i chassis and component LEDs, 19 MSA1510i controller LEDs, 20 N non-hot-pluggable devices, removing, 38 non-hot-pluggable parts, MSA1510i, 37 O operating and performance specifications, 13 P Packet InterNet Groper (PING) overview, 30 part numbers 2-Port Ethernet i
replacing 2–Port Ethernet iSCSI module, 53 fan module, 55 hard drive, 42 best practices, 42 MSA1510i chassis components, 61 power supply module, 59 SCSI I/O module, 57 replacment parts HP limited warranty, 32 T technical support HP, 9 service locator website, 9 thermal failure, caution, 41 tools required for servicing, 33 type recommended, 33 U utilities, configuration, 29 S safety notices, 73 SCSI I/O module installing, 58 LEDs, 27 part numbers, 11 removing, 57, 57 replacing, 57 specifications, 15 ve